Search Documents

By Ana Chiquini, Clayton V. Deutsch

The most common approach used in the mining industry for mineral resources modeling is to estimate the grades using ordinary kriging and report the recoverable resources based on this deterministic estimated model. Mineral resources calculated with kriging are a smooth representation of the actual distribution of grades and do not provide an assessment of uncertainty. Unlike kriging, simulation reproduces the variability of the grades in the mineral deposit and provides an assessment of uncertainty. Reporting mineral resources directly on high-resolution simulation results would assume perfect knowledge of the grade at the time of mining and selectivity at the scale of the data. There will always be uncertainty left at the time of mining, so assuming perfect knowledge of the grade in the future is incorrect. There are two concerns when geostatistical simulation is used for resources modeling: the information and the mining selectivity effects. A new framework for resource estimation is proposed with two separate modules to address those concerns. The information effect is accounted for by anticipating the additional production data that will be available at the time mining to guide the destination for the mined material. The mining selectivity effect is addressed by mimicking the grade control procedure to get mineable dig limits at a chosen selectivity, represented by a minimum mineable unit size. In addition to a prediction of recoverable resources that will be closer to the material mined in the future, the framework proposed provides an assessment of local and global uncertainty for risk management.

May 26, 2020

By Brendan Reilly, Jon Isaacson, Paul McDermott

Kenny/Shea JV is constructing the water intake tunnel for the new Elm Road Generating Station, a supercritical coal-fired power plant in Oak Creek, Wisconsin, being built by Bechtel Power Corporation. The intake tunnel system consists of a temporary mining shaft, pump house and intake channel riser shafts, and four lakebed intake shafts. An 8.33 m diameter, 2,800 m long TBM mined rock tunnel is being constructed to connect the shafts. The intakes are located 2.4 kilometers offshore in Lake Michigan. The shafts and tunnel are being constructed in glacial tills and Silurian Dolomite. The estimated tunnel completion is December 2007.

Jan 1, 2007

By M. L. Mellish

The year 1988 unexpectedly turned out to be a good year for the US coal industry. In fact, it was a third consecutive year of record coal production. Accord¬ing to preliminary Energy Information Administration data for 1988, domestic coal consumption went up 5%, or 41 Mt (45 million st), from 1987. Coal exports were up by a surprising 13.6 Mt (15 million st). In 1988, 22.7 Mt (25 million st) of coal were drawn from stockpiles for consumption. Even so, US coal production increased to 862 Mt (950 million st). That was up 28 Mt (31 million st) from 1987. While coal consumption, exports, and production were up, delivered prices for steam coal continued to slide during the year. Metallurgical coal prices, however, firmed up and showed a moderate increase. This reflected tight metallurgical coal markets at home and abroad. Coal consumption US coal consumption reached 800 Mt (882 million st), compared with 759 Mt (837 million st) in 1987. Increased metallurgical coal consumption was one factor. Most of the rise in coal consumption, however, was due to unexpectedly high electricity demand. Unseasonably hot summer weather al lowed added coal-fired electric generation to supplement the drought-related reduction in hydro-electric power supply. Electric utilities consumed 687 Mt (757 million st) of coal in 1988, 35.4 Mt (39 million st) more than in 1987. Coal-fired power plants remained the primary source of US electricity generation, providing 57% of the total in 1988. Coal consumption at coke plants increased 13%, to 38 Mt (42 million st), from the level consumed in 1987. This increase reflects the recent recovery in the iron and steel industry. Metallurgical coal consumption in 1988 could have been greater. But US coke plants reportedly reached their maximum practical production capacity. As a result, net US coke imports amounted to 1.45 Mt (1.6 million st). Despite increased industrial activities, steam coal consumption by industrial plants was up only slightly from the 1987 level, amounting to 69 Mt (76 million st) in 1988. Residential and commercial coal consumption remained virtually unchanged at 6.4 Mt (7 million st). Coal exports and imports US coal exports rebounded in 1988, reaching 86 Mt (95 million st). It was the highest level of annual US coal exports since 1982, when they reached 96 Mt (106 million st). An unusual set of factors led to an opening for US coal exporters in 1988: • a high level of industrial production in Japan and the European Economic Community, • supply disruptions due to labor problems at coal mines in Poland and Australia, • a drought-related reduction in hydro-electric power generation in Canada, requiring increased coal-fired generation, • China's problems in meeting its export commitments, and • a fall in the value of the US dollar. US metallurgical coal exports in 1988 amounted to 56 Mt (62 million st), 9.1 Mt (10 million st) more than the 1987 level. Europe, Japan, and Canada were the principal importers of US metallurgical coal in 1988. European countries, in particu¬lar, increased their take by one-third of US metallurgical coal. The labor problems in Poland and Australia contributed to these higher levels of imports. So did increases in pig iron production of 8% in Japan and 9% in the European Economic Community. US steam coal exports - including bituminous, anthracite, and lignite-increase to 30 Mt (33 million st). This was up from 25.4 Mt (28 million st) in 1987 Contributing to this overall rise were 1.8-Mt (2-million st) increase in shipments to Canada and a 2.7-Mt (3-million st) increase to Europe. Unaffected by the somewhat tighter world coal market, US coal imports showed a slight increase to 1.8 Mt (million st) in 1988. Colombia continue to be the leading exporter to the United States, followed by Canada and Venezuela. Venezuela's entry into the US market is a relatively recent one, having made its first significant shipment in the fourth quarter of 1987.

Jan 1, 1989

By Ronald L. Wiegel

In the 2000 page Handbook of Mineral Dressing by A. F. Taggart, the subject of material or metallurgical balances is covered in only six pages of eve-straining type. Although Taggart's work was compiled before 1945, and there has been significant progress since then in most areas of mineral processing, the practicing metallurgist's approach to metallurgical balances remains exactly the same as described in those six pages. There are several portions of Taggart's text appropriate to introduce the subject of this paper which I would like to quote: "Milling Calculations. Computations of per¬formance in milling are complicated by the fact that it is a continuous rather than a batch operation, that the quantities of solid materials handled are large and usually mixed with water, hence difficult or impos¬sible to weigh. Fortunately it is possible to determine many facts concerning perfor¬mance without knowing weights, if the value of various constituents is known in some common unit, e.g., the content of some par¬ticular metal or mineral, or of water, or some ingredient soluble therein, or of par¬ticles of a particular size or falling within some particular size range, or the like."

Jan 1, 1979

By W. G. Pariseau

Equivalent elastic properties of discontinuously jointed rock masses are computed using a non-representative volume element(NRVE) approach within a three dimensional finite element program. Joint persistence, defined as the percentage of a joint plane that is actually occupied by joint material, is used in the NRVE computations as a step towards greater realism in stability analysis of mine openings. Persistence p is also the probability that a segment of a joint plane is occupied by joint material. Computations reveal a threshold phenomenon in jointed rock mass moduli similar to that observed in percolation theory. A rapid decrease in moduli occurs above a critical value pc(about 0.6). A detailed analysis of the well-known solution for stress about a circular opening in isotropic, elastic ground illustrates the effects of joint set orientation, spacing and persistence. Although stable “on average”, joint segment failures reveal a threat to stability and point towards rational design of reinforcement or support of discontinuously jointed rock masses.

Jan 1, 2003

By Jamal Rostami, Levent Ozdemir, Amund Bruland, Filip Dahl

Cerchar Abrasivity Index (CAI) is one of the commonly used tests to evaluate rock abrasiveness for cutter life/cost estimations of TBM projects. There are at least 3 style machines, 2 different pin hardness, and the test could be run on fresh rock surface VS a sawn surface. Each of these parameters has a meaningful effect on the results, but its impacts were not fully understood nor its implications well explored. This paper reviews the current practice of Cerchar testing and its implications on geotechnical investigations related to TBM tunnels and provide a set of guidelines on testing and reporting of the test results for future projects.

Jan 1, 2005

By M. Fan

Froth flotation is the most widely-used method of separating fine coal, especially coal with coking properties. However, froth flotation is not efficient for treating ultrafine coal and coarse coal particles. Our previous fundamental test results demonstrated that cavitation-generated nanobubbles can significantly improve coal and phosphate flotation performance over a wide particle size range. In this study, the effect of nanobubble on the flotation performances of different particle size fractions of coal was investigated using a bank of 10-liter flotation cells, a specially designed 50 mm inside diameter column and a 152 mm inside diameter column. It was found that nanobubbles that were either directly formed on or subsequently attached to the surface of coal particles during coal froth flotation process improved flotation efficiency. The use of nanobubble in a bank of mechanical cells flotation and column flotation significantly increased the flotation recovery at a given product grade. Nanobubbles increased the flotation rate constants of different coal particle sizes. The presence of nanobubbles in flotation slurry could extend the lower and the upper particle size limits for effective coal flotation.

Jan 1, 2012

In February 2001, Kalgoorlie Consolidated Gold Mines (KCGM) commissioned its first full-scale ultra fine grinding (UFG) plant to supplement existing roaster concentrate treatment capacity. This process involves the fine grinding of refractory pyritic concentrate to 10µm, followed by direct cyanide leaching for the recovery of gold. By this means gold is economically extracted from the concentrate without the need to first oxidise the host pyrite. This paper details the history of the project from initial laboratory testwork comparing possible treatment options, to current performance of the 12 tph plant. This includes the cost comparison of the major treatment options, the laboratory and pilot scale UFG performance, the UFG mill selection, cyanide leaching of UFG product, commissioning and plant performance to date.

Jan 1, 2002

By I. Fafoutis

Laboratory column studies were conducted in order to assess the effectiveness of slag and red mud reactive barriers for cleaning up leachates generated at mining and waste disposal sites and loaded with copper and manganese. Solutions containing the metals of concern were prepared by dissolving the required quantities of CuSO4?5H2O and MnSO4?H2O in distilled water so that Cu concentration was 100 ppm and Mn 20 ppm. Flow rates of 25 mL.h-1 for Cu solution and 75 mL.h-1 for Mn solution were used in order to simulate aquifer water velocities of 1 ft/d and 3 ft/d respectively. Solutions were pumped upflow, in Plexiglas laboratory columns filled with each reactive medium, using peristaltic pumps. Measurements of middle and outflow column pH, redox potential, conductivity and elements concentration were performed to provide information regarding removal mechanisms for both elements and exhaustion/inactivation rates for each reactive medium. Both reactive media showed fairly good removal efficiency over the period studied. Copper was mainly removed by precipitation and formation of Cu(OH)2 while removal of manganese was due to precipitation of Mn(OH2).

Jan 1, 2006

By John Dasher

In 1980, some US cars were designed and built to metric dimensions; wine and gas were sold by the liter; and the March of Dimes Walkathon was measured in kilometers. Although the US Congress has taken a ''soft" approach to metrication, and public resistance to the idea remains strong, the use of metric units is becoming more and more widespread. As the minerals industry becomes more international in scope, US mining companies are converting to the metric system-particularly those companies with business interests overseas.

Jan 2, 1981

By Fulvio Tonon

And Rabcewicz said ?tunnels should be driven full face whenever possible.? ADECO, which stands for ?Analysis of Controlled Deformations in tunnels,? now allows us to fulfll Rabcewicz?s dream in any stress-strain condition. In order to achieve that dream and its consequent control over cost and schedule, however, NATM must be abandoned for the ADECO. The paper presents the basic concepts in the ADECO approach to design, construction and monitoring of tunnels together with some case histories, including: full face excavation for Cassia tunnel (width of 22 m, height of 14 m) in sands and silts under 5 m cover below an archeological area in Rome, Italy; Tartaguille tunnel (face area > 100 m2) advanced full face in highly swelling and squeezing ground under 100 m cover where NATM led to catastrophic failure, France; and 80 km of tunnels (face area > 100 m2) advanced full face in highly squeezing/swelling ground under 500 m cover for the high-speed railway line between Bologne and Florence, Italy (turnkey contract).

By S. K. Kawatra, K. J. Shoop, T. C. Rao, T. C. Eisele

This study investigates the use of a horizontally- baffled column (7.6 cm inside diameter by 344.2 cm high) to reduce the ash content of a high ash bituminous coal. Tests were carried out to determine how the baffled column responded to changes in feedrate, reagent dosage, and feed quality, and to compare its performance with a conventional column installation in an operating plant. In this paper, the results of this investigation will be reviewed and discussed.

Feb 24, 1997

By T. C. Eisele

The use of column flotation was considered for the ?reverse flotation? of iron ore, where the gangue (quartz) was recovered in the froth product. This use of the froth for carrying the gangue mineral rather than carrying the valuable concentrate significantly changes the operational requirements of the column. The objective of this work was to determine which of several column flotation technologies would be most suitable for this type of flotation operation. Studies were carried out using both the Jameson column and the Deister column. Comparative results are presented that show the capabilities of both column types in this application relative to conventional Wemco flotation cells. Columns were demonstrated to have grade-recovery performance superior to what could be achieved with conventional cells. Two-stage flotation with the columns could produce a concentrate that was up to 70.2% Fe at 87.5% iron recovery, compared to 70.4% Fe at only 77.7% iron recovery for four stages of flotation in conventional cells. It was shown to be particularly important to operate the columns to recover a maximum of the quartz gangue into the froth. It was noted that there are often problems in scale-up of laboratory columns to plant scale, because the increase in height and the decrease in the ratio of height to diameter at the larger scale allows more axial mixing and bubble coalescence, both of which degrade the column performance. Horizontal baffling was shown to improve column performance by reducing axial mixing and breaking up large bubbles, and so the use of such baffles in the reverse flotation application was investigated.

Jan 1, 2007

By James R. Norris, Thomas A. Conto, Gary R. Walter

For at least five decades, a plume containing acidic metal-bearing water has been moving through the shallow alluvial aquifer along Pinal Creek in the Globe-Miami area. Two chemical facies of water are distinguished in the alluvial aquifer: (1) a metal-rich acidic plume with gram per liter concentrations of metals (primarily iron) and pH values between 3 and 5 and (2) neutralized water with a pH greater than 5, low concentrations of metals, and high concentrations of sulfate and manganese. Historically, the acid plume has moved through the aquifer at an average velocity of 0.6 m/day, ten times slower than the average pore velocity of groundwater in the aquifer calculated using the Darcy equation. The rate of migration of the metal-rich plume is retarded by pH-dependent chemical reactions between acid water and the aquifer matrix. As acid water is neutralized by reaction with calcite, rising pH conditions in- crease the oxidation rate of iron and decrease its solubility resulting in the precipitation of ferric hydroxides. The formation of ferric hydroxides is a proton releasing reaction which main- tains acidic conditions. The acidit of the plume and the neutralization capacity of tKe aquifer are best assessed in terms of the iron content of the water and not the hydrogen ion activity computed from pH measurements. The parameters controlling plume migration are: (1) the calcite content of the aquifer (2) the iron acidity of plume water, and (3) the rates of acid neutralization and ferrous iron oxidation. A numerical solute transport and reaction model based on the concept of iron acidity effectively simulates the historical development of acidic conditions, predicts the behavior of the plume, and was used as a management tool to identify the most efficient and cost effective remedial strategy.

Jan 1, 1991

By M. S. Safarzadeh

Over the last fifty years, the treatment of enargite concentrates has not received much attention, primarily because of the availability of other clean concentrates suitable for processing with existing smelting and/or leaching technologies. As traditional copper ores have become scarcer, copper-arsenic ore deposits have garnered more interest. Arsenic release is a significant concern during the treatment of enargite concentrates by pyro or hydrometallurgical methods. Enargite is also very refractive in standard leaching procedures. Thus, economical treatment options for enargite concentrates are needed. Preliminary experiments have shown that the acid bake-leach process could be adapted and used for the treatment of enargite concentrates. In this study, low-temperature (100-400º C) sulfuric acid baking of an enargite concentrate followed by water leaching has been evaluated. The results indicate the thermal transformation of enargite to copper sulfate happens during sulfuric acid baking, with most of the arsenic being released from the concentrate into the gas phase when baking at 400º C. The condition for maximum copper extraction (~100%) from the concentrate was found to be 400º C, a sulfuric acid concentration of 0.5 mL/g and two hours baking time. Part of the arsenic was captured in the form of arsenopyrite (FeAsS). X-ray diffraction (XRD) analysis proved the presence of some arsenic in the form of claudetite (As2O3) in the baked concentrate. Acid baking of pure enargite behaved in a similar fashion.

Nov 1, 2011

By Pelin Altinkaya, Maria Leikola, Jussi Liipo, Mika Haapalainen, Mari Lundström, Eero Kolehmainen

With decreasing ore grades, the tailings of mining operations are becoming of increasing interest as metal-containing secondary raw materials. The objective of the current work was to investigate chloride leaching of gold, copper, cobalt, nickel, and zinc present in the flotation tailings. In the current study, the effect of cupric ion as an oxidant (0–50 g/L) and NaCl (150–250 g/L) on metals extraction was investigated. The other parameters, such as pH (1.8), temperature (95 °C), solid/liquid ratio (25%), oxygen feed rate (1200 mL/min), leaching time (24 h), and stirring rate (950 rpm), were kept constant. Gold dissolution rate was shown to increase with increase in cupric ion concentrations up to 50 g/L. Also, increase in NaCl concentration up to 250 g/L increased gold extraction. Majority of the copper present in the flotation tailings could be dissolved with all the all solutions investigated. The other base metals, cobalt, nickel, and zinc extractions were also shown to increase with increase in the cupric ion and sodium chloride concentration. However, even in the absence of cupric ion addition (t = 72 h, 250 g/L NaCl), the final extraction of Cu, Ni, Zn, Co, and Fe increased up to 98, 93, 83, 76, and 80%, respectively. This shows the power of inherently originating oxidants present in the tailings. Furthermore, the solid analysis of the leach residue indicated that leaching the flotation tailings in pure NaCl may result in partial gold dissolution. The results demonstrate that significant amount of metals present in the tailings could be extracted even with only NaCl as added chemical in the presence of oxygen feed, oxidizing agents originating directly from the raw material. This can provide an advantageous cyanide-free method for extraction of metals from very low-grade tailings with low chemical consumption.

By Paul Gribbon, Julius Strid, Greg Colzani, Jim McDonald

Portland, Oregon’s $370 million West Side Combined Sewer Overflow Tunnel Project has completed the final phase of construction and commissioning. The construction contract, which began in September 2002, was a reimbursable cost plus fixed fee contract that followed a qualifications-based contractor procurement process and apre-construction planning phase. This paper addresses the final results of the contracting method and provides a lessons-learned case history. Specific items addressed include the benefits realized from the contracting method, areas of improvement, final costs compared to the original contract estimates, design changes and schedule impacts, and subcontract management issues.

Jan 1, 2007

In conjunction with steady increases in production levels, longwall operators have applied greater quantities of ventilating air and spray water in an effort to control respirable dust and/or methane. Air velocities greater than 7.6 m/s (1500 fpm) have been measured on longwall faces. Operators have expressed concern over the potential entrainment of respirable dust at these high velocities. The greatest likelihood for entraining dust into the high velocity airstream may occur as shields are advanced allowing relatively dry particles to fall from the shield canopy directly into the airstream. Laboratory tests to simulate dust liberation during shield movement were conducted at the Pittsburgh Research Laboratory of NIOSH at velocities ranging from 2.0 to 8.2 m/s (400 to1600 fpm). Airborne dust samples were obtained with personal impactors to quantify the size distribution and concentration of the dust entrained at the various air velocities. Statistically significant increases in both total and respirable dust concentrations were measured as test air velocities were increased.

Jan 1, 2001

By A. S. Winters

INTRODUCTION Homestake Mining Co. owns and operates the Bull¬dog Mountain mine near Creede, CO. Lead-silver con¬centrates are produced from ores extracted from narrow veins which dip from 1.04 to 1.39 rad (60 to 80°). An¬nual mill throughput is approximately 90 700 t (100,000 st). Ore shoots average 2 m (7 ft) in width and the ore is often weak, muddy, and poorly consolidated. Walls can be either strong or highly fractured along the strike of the veins. Cut-and-fill methods were initially selected to mine the deposit and considerable overhand mining occurred during the initial stages of the mine. Because of un¬stable ground conditions, mine management recognized that other methods would have to be employed. Undercut-and-fill mining was adapted to extract the loose ore from narrow veins and is presently the primary method used. Approximately 80% of the annual pro¬duction is extracted by this system. Loading ramps are positioned along the strike of the vein on 90-m (300-ft) intervals to allow for 45-m (150-ft) long cuts in each direction from the extraction raise. This interval was selected for efficient slusher operation and stope cycling. Loading ramps rather than chutes were selected for ore movement into 4.5-t (5-st) Granby-type cars because of extremely sticky ore conditions. Mined-out areas are filled with deslimed mill sands. Sand is pumped from the mill into two mine storage dams where the water is decanted. Each dam has a 544-t (600-st) capacity. Sand is pumped into the mine at a 30 to 40% slurry through 2195 m (7200 ft) of 51-mm (2-in.) thick wall pipe. When called for, sand is reslurried within the dams to a density of 55 to 65% and pumped to the particular mine opening requiring fill. Dry cement is added to the slurry prior to pumping. The capacity of the mine fill system is 20 t/h (22 stph). DEVELOPMENT Vertical development below the main adit level oc¬curs on 61-m (200-ft) intervals from an internal winze. Main haulage drifts or laterals are 2.7 x 2.7 m (9 x 9 ft) in section and driven parallel to the vein structures. Ground conditions generally dictate that better progress can be realized in the footwall than in the hanging wall. A distance of approximately 21 m (70 ft) is maintained between vein and drift openings to accommodate a smooth 18-m (60-ft) radius curve for crosscuts which are driven on 91-m (300-ft) intervals. Approximately 18 m (60 ft) of tail room is driven past the vein inter¬section to accommodate train loading. Ore and waste are hauled using diesel or electric driven locomotives operating over 18-kg (40-Ib) rail [762-mm (30-in.) gage]. Loading ramps are established above each crosscut¬ vein intersection. Scram drifts are then driven in the vein to determine the width and grade of the ore. If a prior decision to mine the block had been reached, then the scram is driven only far enough [about 12 m (40 ft)] to establish a drawpoint and scraper tail room. In most cases, the drawpoint is a 2.1 x 2.1-m (7 x 7-ft) cutout driven about 2.4 m (8 ft) into the footwall. On the level above, a raise bore station is established in the footwall to one side of the crosscut-vein inter¬section. The station is of sufficient size to accommo¬date a Robbins 41R raise boring machine. Support for the station is accomplished with 1.2 and 1.8-m (4 and 6-ft) roof bolts and wire screening. Once completed, a 152-mm (6-in.) concrete slab is poured and the raise drill set in position to center the 1.5-m (5-ft) diam hole approximately 1.8 m (6 ft) from the vein footwall. A 229-mm (9-in.) pilot hole is then drilled to the scram cutout below and reamed back to full diameter (see Fig. 1). STOPING Initial mining in a typical undercut-and-fill stope be¬gins from the top of the borehole. The initial cut can be either immediately beneath the track level or the old scram drift depending upon the particular situation. Cuts vary but are generally 2.4 to 3 m (8 to 10 ft) high. Support is accomplished by square-set timber, overhead caps, or roof bolts and screening depending upon ground conditions. Once the initial cut is removed, underhand timber and screen is installed and cemented sand fill placed. The stope is then ready for undercut mining. Prepara¬tion work begins with sinking 4.5 to 6 m (15 to 20 ft) on the borehole plus cutting a slot to the vein. As sinking progresses, hanging sets are installed to provide man¬way and service facilities. Hanging sets 1.7 m (5 ft 8 in.) long and 1.6 x 2.2 m (5 ft 4 in. x 7 ft 4 in.) in section are installed with steel hangers similar to shaft sets. Framed 203 x 203-mm (8 x 8-in.) timbers are made up in advance and shipped to the stope during sinking operations. When manway and service facilities are completed to the floor of cut to be mined, generally 3.65 to 4.3 m (12 to 14 ft) below the previous sand fill, the ore is removed to the hanging wall plus a round each way along the vein. Levelers or long stringers are then installed over the raise opening to support the work deck, slusher, and grizzly opening. All waste and ore from the sinking process is fed by gravity to the raise (see Fig. 2). Once the stope is equipped, mining pro¬gresses outward in each direction from the grizzly open¬ing. Stope equipment consists of 907 kg (2000 lb) pull air tuggers, timber skips, 11-kW (15-hp) ventilation fans, 15 to 22-kW (20 to 30-hp) electric slushers, 762 to 1270-mm (30 to 50-in.) scrapers, 67-mm (25/a-in. ) jackleg drills, as well as other drilling and blasting supplies. In narrow stopes [generally less than 2 m (7 ft) wide], no support is required for the underhand caps of the previous fill. Where wide sections in the vein occur, segment braces are installed beneath the caps to insure that the sand support cannot slip away from the hanging wall. Sections as great as 6 m (20 ft) wide and 4.5 m

Jan 1, 1982

By A. Bascetin

Waste materials caused by mining activities are an important environmental problem. Paste technology is a good alternative for waste management because it has many benefits in the aspects of environment, cost and safety. Disposal of process wastes in paste form is an attractive option for waste management, as it eliminates or reduces the risks associated with conventional methods. Due to the geotechnical characteristics of the paste, it is very similar to soil materials. So determining the geotechnical properties of the paste material is essential to durability of the paste. The some important geotechnical properties are compressive strength, porosity, shear strength, hydraulic conductivity, water content, consolidation, etc. In this study, the important parameters and the relation between them were investigated and obtained some results which will affect for optimum design of waste management.

Jan 1, 2012