Search Documents

By M. J. Hughes

Kaiser Steel Corporation's Eagle Mountain operations are located in Southern California at a distance of about 130 miles east of the Corporation's steel plant at Fontana, California, and at a distance of about 225 miles from the nearest harbors which are located at Long Beach and Los Angeles, California Although the Eagle Mountain ore bodies are strategically located with respect to the steel plant and the harbor facilities, they are not of a very high grade and 'the geologic nature of the deposit makes it very difficult to mine and to concentrate. The iron ores occur as partial replacement of older zones mainly within dolomites and to a lesser extent within quartzites and quartz monzonites. The alteration was extremely variable and generally resulted in the formation of pyritic magnetic which, in part of the ore body, was leached to remove the pyrite and change the magnetite to hematite. Although the overall ore body is large, a major portion of it contains sulfur in the range of 1.0% to 5.0%. Obviously, this is too high a sulfur content for direct use in blast furnace feed.

Jan 1, 1968

By Frank E. Chase

Preventing pillar squeezes, massive pillar collapses, and bumps is critical to the safe and efficient recovery of coal during room-and-pillar retreat mining. To help prevent these problems, the U.S. Bureau of Mines (USBM) has developed the Analysis of Retreat Mining Pillar Stability (ARMPS) computer program. ARMPS calculates stability factors (SF) based on estimates of the loads applied to and the load-bearing capacities of, pillars during retreat mining operations. The program can model the significant features of most retreat mining layouts, including angled crosscuts, varied spacings between entries, barrier pillars between the active section and old (side) gobs, and slab cuts in the barriers on retreat. It also features a pillar strength formula that considers the greater strength of rectangular pillars. The program may be used to evaluate bleeder designs as well as active workings. A data base of 110 pillar retreat mining case histories has been collected across the United States to verify the program. It was found that satisfactory conditions were very rare when the ARMPS SF was less than 0.75. Conversely, very few unsatisfactory designs were found where the ARMPS SF was greater than 1. 5.

Jan 1, 1995

By Douglas Castleberry

The degree of fragmentation obtained in primary quarry blasting has always been a factor in the speed of digging' the muckpile This paper will discuss a case history of increased production and associated lowered costs from increased fragmentation. The quarry under discussion is fairly new, located in Georgia, and is in the large operation .category. Loading is done by three yard shovels, and, primary crushing by a 48" x 60" haw crusher preceded by a 5' wide feeder. The stone is a hard granite gneiss, of Los Angeles rating 22, and apparent specific gravity is 2.68. The product is shipped to points in that state for railroad ballast, concrete aggregate, and road building stone. Inasmuch as fairly large shovels and a large Jaw were to be utilized, initial drilling and blasting were pointed toward producing fairly large sized muck for this large equipment. This was following a concept somewhat in vogue for some years in the Southeast wherein many large equipment plants would tend towards larger fragmentation, and smaller equipped plants would conversely tend toward attempts at smaller sized rock piles for smaller shovels and crushers.

Jan 1, 1960

By C. F. Johnson

Nearly all of the sulphur produced in the world today is converted to sulphuric acid and 49 % is used in the manufacture of fertilizers. In the last few years we have seen the beginning of another chapter in the volatile history of sulphur as the severe shortage of 1963:-67 has been transformed into present-day surplus. Prospects for further aggravation of this situation in the years ahead seem assured. In 1970, western world production showed a rate of increase of 4 -5%, which 1S somewhat less than that of 8% for the period 1963-1967. The rate of growth of consumption dropped considerably in 1968 when the demands of the fertilizer industry fell. During the same period of time, wide-spread demands have been set in motion for a clean environment which indicates that a fundamental change in sulphur supply, demand, and even sources, is likely to result from this upheaval. The sale of sulphur by Poland to the western world has increased and for 1970 was estimated at over one million metric tons. In the next few years, increase in Canadian sulphur supply will stern from two sources;

Jan 1, 1972

By B. A. Wills

With the increasing need to mine lower grade ores, high energy-related costs in comminution are of major concern. Very fine grinding is needed to liberate the very fine mineral particles in these ores. Not only is this expensive but it leads to greater losses in 'slimes'. In the early 1970's, 50% of the tin mined in Bolivia, 30% of the phosphate mined in Florida and 20% of the world's tungsten were lost in this way (Somasundaran, 1979). Gravity concentration techniques become unacceptably inefficient for particle treatment below 25-50µm, and even flotation fails in the ultra-fine range. Two approaches can be adopted to try to overcome this problem. The first involves increasing the efficiency of existing equipment or developing new slimes treatment processes. Gravity devices such as the Bartles-Mozley concentrator have been developed for this purpose and good recovery has been reported from 100µm down to 5µm. Such machines, however, have relatively low throughputs, so that large areas of plant space are generally required. Flotation is rapidly growing in importance for the treatment of ultra-fine minerals traditionally treated by gravity concentration.

Jan 1, 1986

By S. Hardcastle

Kidd Creek mine has recently completed upgrades of its primary ventilation systems enabling it to maintain a delivery of 1200 m3/s to continue mining ore zones extending to over 3000 m below surface. Following these upgrades the mine initiated a multi-stage review of their ventilation usage. The focus of these reviews, ranged from a brainstorming session of invited experts, through an evaluation of production plans to a detailed analysis of production data to determine if the ventilation system could be run more efficiently, thereby reducing the mine?s power consumption and associated operating costs. The initial review identified 1500 kW of installed fan power that could be eliminated from the primary ventilation system. The benefits of the subsequent analyses, so far, are not as measurable. The second and third analyses, respectively using long range production plan data and historic production data to determine ventilation requirements based upon diesel equipment, did not agree. Both were shown to have limitations, the future based analysis underestimating, and the historical analysis overestimating the requirements. Regardless of the failings of each method, important outcomes were achieved from the detailed analyses, namely, the ability for a mine to meet a forward analysis prediction of airflow depends on its ability to adjust the ventilation to meet the dynamic nature of the mining process. Also, to minimize total ventilation requirements, a mine must regularly redistribute its airflow; this not only reduces the total volume requirement but also increases the variability of the delivered flows which can provide further operational savings. Since the detailed analyses, the Kidd Creek mine has implemented a more frequent ventilation review and redistribution procedure; consequently, it now operates with an average delivery of 930 m3/s, which is 23% lower than in 2005 at the start of the review process.

Jan 1, 2009

By S. C. Lamey, P. A. Hesbach

This study evaluated the use of regionally produced coal combustion products to neutralize and remove metals from acid mine drainage (AMD). Synthetic AMD mixtures were treated with a number of fly ashes and fluidized bed combustion (FBC) ashes. All of the ashes reduced the volume of the sludge produced and gave a faster settling rate than the sludge produced by treatment with lime. Faster settling allows greater throughput rates. In addition, the FBC ashes, which generally contain alkaline components used for sulfur capture, completely neutralized the acidity and, if desired, raised the pH above 10. The fly ashes, on the other hand, reduced the final volume of sludge but required additional neutralizing agents to attain a pH >5. The pH of the AMD can be taken to above 10 to insure complete removal of manganese, or it can be taken to a more neutral pH of 7 or 8 to allow for the safe introduction of the aqueous phase into ponds or streams. The process combines two industrial waste products to reduce the disposal volume of one of the waste products and to produce an environmentally safe aqueous discharge.

Jan 1, 2002

By A. S. Ericson, J. H. Corrigan, E. J. Jahnsen

Calcine is transported from the Reduction Plant at 850°C in insulated hopper cars and charged into three rectangular electric melting furnaces each equipped with three - 18.5 MVA transformers. The electrical energy is applied through six in line prebaked carbon electrodes, and slag and metal are tapped at opposite ends of the furnaces on an intermittent basis. The slag, 5000 tonnes per day, is disposed of by a pot train directly to the dump. The ferronickel, 250 tonnes per day, is tapped into 40 tonne capacity ladles in which it is refined in two ASEA-SKF ladle furnace stations. Casting is done over lip at 1520°C in a pig casting machine with stepless speed control at up to 55 tonnes per hour. The ingots are stacked into self palletizing bundles weighing about 1500 kilograms and are strapped and tagged and transported to the seaport, from which the final shipment is made to the world market. The paper describes constructional details and gives information of both normal operation and start-up and shut-down procedures. Consumption figures for refractory, electrodes, electric energy and refining additions are given and metal chemistry is given before and after refining.

Jan 1, 1979

By James K. Gowans

The Red Dog Operation is located in northwestern Alaska at Latitude 68°, 100 miles north of the Arctic Circle and 50 miles inland from the Chukchi Sea. The orebody was acquired by the NANA Regional Corporation, (an Alaska Native Corporation established by the Alaska Native Claims Settlement Act of 1971), in 1980 in their land selection. In 1982 Cominco American and the NANA Corporation signed a development agreement and Cominco Alaska Inc., a wholly owned subsidiary of Cominco American, was formed to manage the Red Dog Project. An extensive exploration program in 1980 -1982 outlined a mineral inventory of 85 million tons, at a grade of 5.2% Pb, 17.1 % Zn, and 2.4 oz/ton Ag, which makes the Red Dog the second largest deposit ever discovered. Broken Hill, in Australia, is the only zinc orebody which was originally larger than Red Dog. The design of the facilities is to process 2.1 million tons of ore annually, which will produce 560,000 tons of zinc concentrate, 100,000 tons of lead concentrate and 50,000 tons of bulk lead/zinc concentrate.

Jan 1, 1991

By F. H. Nehl

The U.S. Bureau of Mines investigated the selective electrowinning of Ag and Au from cyanide solutions contaminated with Cu with the goal of decreasing the amount of Cu co-deposited. Decreasing Cu co-deposited will reduce refinery costs. Direct current was applied to the cell in pulsed and square wave voltages at 0.7 A?h per 150 mL of solution. Times tested for each cycle ranged from 1 to 10,000 ms. Graphite, lead, and stainless steel were evaluated as electrode materials. Square wave e1ectrowinning at 70? C gave the best separation of Ag and Au from Cu. Applying 2.5 V during the duty cycle, 0.0 V the rest of the period, a duty cycle of 10 to 30 pct, and a period of 100 ms to 1,000 ms gave the following results: Ag concentrations decreased from 34 µ g/mL to 0.1 µ g/mL, Au concentrations decreased from 54 µ g/mL to 0.2 µ g/mL, and Cu concentrations remained almost constant at 560 µ g/mL.

Jan 1, 1993

By John D. Smart, John W. Sager

The following paper is an evaluation of the instrumentation programs on recent Corps of Engineers tunneling projects. The authors have first-hand knowledge of the NORAD Cheyenne Mountain Complex (NCMC) Expansion Project. Information on the other projects comes from conversations with those directly involved in the instrumentation programs and from referenced reports. The specific objectives of this paper are: (1) to state the purposes of the instrumentation programs, (2) to discuss the benefits gained from the instrumentation, and (3) to present conclusions from this study that will provide guidance to those planning instrumentation on future projects. Presentation of detailed descriptions of the projects and instrumentation data is limited to that necessary to the accomplishment of the above objectives. NCMC EXPANSION PROJECT The NCMC is located at a depth of approximately 800 feet in Cheyenne Mountain near Colorado Springs, Colorado. For the current expansion project new chambers were mined to accommodate a new diesel power plant and associated cooling and air handling equipment. During 1971 some 55,000 yd3 of granite were mined through existing access tunnels for this expansion. A model of the new excavation is shown in Figure 1. The light shaded areas are new openings, and the dark areas are portions of the existing operating complex. The large chamber to the right is the power plant chamber and has a span of 67 ft, a height of 50 ft, and a length of 172 ft. The other large chamber on the lower level is the cooling tower chamber and has a span of 38 ft, a height of 45 ft and a length of 185 ft. The small chamber on the upper level has a span of 20 ft and is 27 ft high and 140 ft long. Other major excavations are the 18 ft diam air tunnel

Jan 1, 1997

By J. E. Murphy, R. Y. Wan, K. R. Sandgren, M. C. Fuerstenau

As part of a U.S. Bureau of Mines program to evaluate alternatives to sodium cyanide in gold leaching, three organic nitrile compounds were tested for their effectiveness as gold lixiviante. The organic compounds examined were malononitrile, acetonitrile, and cyanoacetamide. The reagents were tested on an oxide ore, two carbonaceous ores, and a eulfidic ore. Acetonitrile and cyanoacetamide were shown to be ineffective gold leachante. Malononitrile was the most successful of the organic lixiviants. On an oxide ore, malononitrile performed shilarlyto sodium cyanide with extractions of around 80 pct. For carbonaceous "preg-robbing" oree, sodium cyanide was completely ineffective while malononitrile extracted 24 pct of the gold. When using a resin-in-leach technique, extraction with sodium cyanide increased to 60 pct and the extraction with malononitrile increased to 80 pct. On the sulfide ore, sodium cyanide and malononitrile performed similarly with 80+ pct extraction as long as the pH of the malononitrile solution wae maintained above 10.5. Malononitrile is six times less toxic than sodium cyanide as measured by LD, levels. Therefore, malononitrile has a significant advantage over eodium cyanide, but its high cost and undemonstrated usefulnees make it unlikely to gain acceptance.

Jan 1, 1993

By M. Yavuz

The use of natural stones like marble is approximately as old as the emergence of human. Marble and natural stone usage of Turkey also dates back to very old times. Marble is produced in Anatolia since the ancient times. The archaeological excavations made in Anatolia indicate that the modern methods that are used for the production of marble blocks in modern world were first used by Anatolian people. Turkey is one of the oldest natural stone producers with its 4000 years of production history, starting from the Marmara Island. Therefore, the territory of Turkey possesses 4000 years of natural stone processing technology and experience. Turkey has fairly richer reserves of marble compared to other countries. This is why the rich and quality marble deposits of Turkey are resembled to the appearance of the Alpine-Himalayan marble belt of the world. Turkey has almost 40% of the total marble reserves (13.9 billion tones) of the world with 5.2 billion tones. Turkey?s marble reserve?s monetary value is worth about 2 trillion dollars. However, only 1% of these reserves are currently being utilized.

Jan 1, 2011

By Jordan Hoover, Erika Moonin, Chuck George

"In response to a severe regional drought and in preparation for the further decline of water levels in Southern Nevada’s Lake Mead, the Southern Nevada Water Authority (SNWA) built a new intake system to ensure water supply to Las Vegas and its surrounding communities. In 2015, design began on the Low Lake Level Pumping Station (L3PS) that will move the water from this lower intake, ensuring operability of the water delivery system despite these declining lake levels. The L3PS Project includes a 159-meter-deep shaft, a large underground chamber, and 34-each 152-meter-deep, 2.4-meter-diameter drilled well shafts to be constructed in highly faulted and fractured ground. The Construction Manager at Risk (CMAR) delivery method was chosen to facilitate early contractor involvement in the design process to address the significant challenges and risks anticipated on this US$650 million Project. This paper describes the CMAR selection process; the CMAR involvement during design and benefits resulting from that involvement; and the unique collaborative effort among the owner, engineer, program manager and CMAR used to evaluate and select the best design approach, preferred underground construction methods, and coordinated geotechnical baseline report. PROJECT BACKGROUND AND NEED Seven of the United States’ western states rely heavily on the Colorado River and its tributaries for their water supply. The primary source of water for the Colorado River is winter snow that falls in the mountains ringing the Colorado River Basin. Flows in the Colorado River vary significantly from year to year, depending on the amount of snow and rain deposited in the basin. Beginning in the year 2000 and continuing to the present, snowfall has been well below documented historical averages and Colorado River flows have diminished."

Jan 1, 2016

By F. P. Schwarz, A. J. Erickson, S. M. Weber

The Mount Hope stockwork molybdenum exposit, Eureka County, Nevada, occurs in a small igneous cauldron complex 32 to 38 mybp in age. The deposit is characterized by alteration zones and mineralized shells symmetrically distributed around multiple intrusives. For samples from the 25 000 meters of 1981-82 drilling, an appraisal of error in in-house sample preparation and in commercial assaying has been made. After splitting, drill core is crushed and reduced in volume (8:1 at 10-mesh, 8:1 at 70-mesh, 6:1 at 200-mesh) to supply 25 grams of 200-mesh pulp for replicate analyses. A 0.5 g portion of the pulp is used for dissolution and atomic absorption analyses. Factors which initially generated unacceptable data variances have been minimized by planning, repeat analyses, introduction of standards, and routine monitoring. Assuming that error between replicate assays defines a Gaussian distribution with its average ideally equal to zero, precision (from preparation including core splitting and analysis of 8400 pairs of molybdenum samples) is on the order of + 25%. The error distribution is not biased. Accuracy is approximately 4% lower than absolute as determined by replicate assays of commercially prepared samples.

Jan 1, 1992

By Solomon S. Katz

As more and more computer software is written for geological mapping applications, the users of the software are discovering the problems of transferring data between the programs, maintaining correct data and integrating maps produced last week with those produced today. One way to deal with these situations is by using a geographic information system (GIs). Last September the USGS and National Academy of Science held a 5-day GIs symposium on integrating technology and geoscience applications (USGS, 1988). It was followed in October by GEOTECH '88 (Peters and Krajewski 1989) which had a session exclusively for GIs applications in the Geo-Sciences. Editorials in Geobyte (Leonard, 1986, 1988) suggested that geographic information systems will be the next major computer programs to be adopted by the mineral industries. As far- back is 1985, the Computer Oriented Geological Society (COGS) printed An Introduction to GIs in their newsletter (Katz, 1985). About 20 years ago, a revolutionary idea occurred in the world of business data processing. It was the idea that all related data be stored in a standard format, in a single place and that all related computer application programs would use the same data.

Jan 1, 1989

By Robin P. Gardner

The mechanistic approach to comminution consisting of incorporating particulate breakage functions into a suitable population balance equation has been developed by a number of researchers over the past decade or so. (1) To date this approach has been developed and demonstrated primarily for batch-operated, laboratory or small-scale ball mills. However, since industrial mills are mostly quite large and operated in the continuous mode; suitable population balance models and methods for obtaining the necessary breakage and other model parameters must be developed. This paper describes and investigates a radioisotope tracer technique for this purpose, Population balance models previously developed(2,3) are adapted for this study.

Jan 1, 1974

By R. R. Klimpel

The use of chemical reagents in flotation has been studied in great detail, e.g. (1, 2, 3, 4). Important progress has been made on the understanding of surface chemistry concepts involved in flotation. However, such scientific studies are often very complex even for rather simple idealized systems. Therefore, the deve- lopment of predictive or quantitative tools for plant engineering evaluation is still in the evolutionary stages. Until further progress in fundamental work is achieved, the operating engineer is faced with semi-empirical physical testing of reagent changes on several sizes of the actual equipment under study to be confident of the economic viability of any change.

Jan 1, 1980

By D. D. Young

During the 1970's a number of covered storage facilities were constructed in North America to store and handle large quantities of bulk, solid materials. This trend, away from outdoor storage piles, will probably continue at a stronger pace in the 1980's. This paper attempts to answer some of the questions often raised about the economics of large covered storage facilities. The paper is in four parts: 1. Why Build a Storage Facility? 2. 2. Common Components of Storage Systems With Details of Six Storage Facilities 3. Results of a Study for 50,000 Mg Clinker Storage 4. Guidelines for Conducting a Study to Select a Storage System.

Jan 1, 1980

By S. S. Cook, S. E. Paulson

The US Bureau of Mines is conducting core leaching experiments with sulfuric acid on oxide copper ores from the Cyprus Casa Grande and Asarco/Freeport Santa Cruz deposit in Arizona to further the understanding of the leaching process in supergene copper ores as it relates to in situ mining. Leach solutions from atacamite mineralization contained 5 to 30 g/L (0.05 to 0.28 oz/gal) copper and few extraneous ions. Leachant from chrysocolla ores, with grades similar to the atacamite, contained 2 to 9 g/L (0.02 to 0.08 oz/ gal) copper and abundant extraneous ions. Quartz and K-feldspar had no impact on leach solution composition at any acid concentration up to 40 g/L - (0.39 oz/gal) while illite and sericite had minimal impact. Biotite, calcium-rich clay, and limonite have a significant impact on solution chemistry when there is abundant free acid in solution. High acid concentra¬tions increase acid consumption in ores with abundant biotite and limonite gangue. High acid concentrations can be used in ores with quartz, K feldspar, and sericite gangues without increasing acid consumption per unit of copper removed.

Jan 1, 1990