Search Documents

By V. K. Gupta

A detailed experimental study of the variations in grinding rate with particle size, particle load, ball diameter, ball load, mill diameter, and mill speed was carried out for a soft cement clinker and a hard cement clinker. The effects of the ball diameter, ball load and particle load were observed to be material (hardness) independent, and those of the particle size, mill diameter and mill speed to be material dependent. A sharp change in the grinding behavior was observed for both the clinkers at about 150 µm size. Below this critical size: (i) the hardness difference between the two clinkers became insignificant, (ii) variation in the grinding rate with particle size became markedly more pronounced, and (iii) mill speed had little or no effect on grinding rate. The importance of these results in the context of process optimization and control is discussed.

Jan 1, 1987

By P. M. Lin

This paper presents an overall stabilization method to eliminate the potential of reoccurrence of subsidence over abandoned mine lands. The method considers column grouting at the specific locations inside the subsidence influence areas including the distressed and stress concentration zones instead of grouting' around and beneath the damaged structures. The later method is commonly used for AML subsidence abatement at the present. By using finite element method the conditions of stress distribution in the strata before and after grouting can be calculated. The design of grout pattern includes the location and number of the grouting holes. Based on the calculation, the proposed method significantly reduces the stress concentration, i.e., the potential of reoccurrence of subsidence can be reduced or eliminated. A comparative analysis including number of grouting holes, grout affected area, stress level, and potential of subsidence reoccurrence will also be presented.

Jan 1, 1990

By William P. Walsh

In December 1983 the author undertook an investigation in east Texas which was organized to learn the feasibility of applying geophysical techniques over shallow lignite deposits. The work embraced experimental high resolution seismic reflection and offset Wenner resisitivity sounds over three 1/4 to 1/2 mile test sections. This site also was sponsored by Woodward-Clyde Consultants (WCC) and a consortium headed by North American Coal Corporation. The principal objective of this investigation was to learn whether the aforementioned geophysical techniques could be applied over shallow lignite deposits (i.e. located at approximately 100' to 300' in depth) and consequently provide structural and stratigraphic information useful for resource and reserve characterization. A secondary objective was to determine if these same techniques could disclose the nature of the overburden and the distribution of ground water therein.

Jan 1, 1986

By James J. Fallon

Last summer Larry Miller of Roberts & Schaefer told me that his AIME committee would like me to present some thoughts on the marketing of industrial mineral fillers and pigments to this illustrious group in Las Vegas. Shortly after, Brian Coupe of "Industrial Minerals" (the magazine) notified me that I would be presenting a paper to the Fourth International Industrial Minerals Congress in Atlanta this June. It seems to me now it might have been more appropriate to reverse the papers. Las Vegas, a town based on risk, might want to hear what we have to say in Atlanta. The subject for June is "Risk Philosophies of U. S. Industrial Minerals Companies". However, upon reflection, marketing of industrial minerals reflects risk philosophies to a considerable extent, so we'll cut the deck and deal on the subject of marketing.

Jan 1, 1980

By Wayne A. McCurdy

I welcome the opportunity to meet with you and discuss the work and program of the Office of Coal Research. Our programs are oriented to serve the conservation objectives of the Johnson Administration and of the Nation by seeking out the most efficient and best uses for coal. We believe that even if only a portion of our program is successful, the coal industry and the Nation will benefit far out of proportion to our expenditures. Operating with a budget of $7,220,000 in Fiscal Year 1966, OCR sponsors contract research which offers potential for achieving benefits to the coal industry in the form of new production and new markets. This directs us into many areas of research activity: in coal combustion, in advancements in mining methods and coal preparation, in new uses for coal, and in associated economic and marketing research.

Jan 1, 1966

By Suzanne Smith, Frank C. Fantauzzo

Introduction America's workforce is the heart of the nation's economy. The health of its members is a matter of national priority. Statistics show that the most common cause of job difficulties is excess use of alcohol or other drugs. Up to 75% of these troubled employees can be returned to productive careers at little expense and with great benefit to their industries. Of the 1.5 million private corporations in the US, only about 500 have alcohol treatment programs. Even fewer have drug abuse programs. It is time that the myths and prejudices surrounding alcohol and drug abuse are dispelled and help is offered. Corporations and labor unions are now finding that programs to treat these diseases benefit both the employees and the industry. The employee derives health and job security. The company sees increased productivity and decreased costs in sick pay and absenteeism. Unfortunately, three-fourths of the nation's 90.5 million workers are employed in establishments of fewer than 500 employees. In these settings, it is unlikely that either management or the unions will take the initiative in developing programs. Alcohol alone affects the health and productivity of nearly 8% of any workforce. This translates to more than 5 million employees in small business. These workers present an opportunity and a challenge. Alcohol abuse costs the nation nearly $116 billion annually. Seventy billion dollars is attributed to lost production. Medical expenditures related to alcohol are estimated to be nearly $13 billion. The National Institute on Drug Abuse (NIDA) estimates the cost of substance abuse to industry to be in excess of $4 billion a year. In addition to its economic impact, substance abuse has serious personal and social consequences. The mining industry experiences the same exposure as other industries to alcohol, drug abuse, and other employee problems. However, the existence of these problems poses special hazards because of the unique conditions found in mining. Mining has many safety and health hazards. Employees must have full control of their faculties and give full attention to the tasks at hand. Designing employee assistance programs An Employee Assistance Program is a cost-effective, confidential, early intervention system. It is designed to help employees

Jan 11, 1987

By Robert M. Stevens, Arnoldo Acuña

INTRODUCTION In the early 1950s, underground miners and tunnel¬ing contractors were experimenting with ways to supple¬ment or eliminate track-bound loading and hauling equipment. Diesel-powered crawler and rubber-tire mounted front-end loaders and trucks designed for use on the surface were being modified and tried with limited but encouraging success. Miners began working with interested manufacturers to explore the develop¬ment of vehicles specifically designed to meet the de¬mands and constraints of underground material han¬dling. By the mid 1960s, load-haul-dump (LHD) vehicles were firmly established as a fundamental part of what has become known as the "trackless" mining concept, used in many mines and many countries around the world. The flexibility, mobility, and versatility of these units have given the industry a useful tool and have added new dimensions to mine development and produc¬tion. Many old mines have been redesigned to accom¬modate these trackless vehicles, and few new mining plans have failed to find some use for the concept during some phase of development and production. By 1977, several manufacturers in several different countries were producing a variety of LHD vehicles to meet the growing worldwide demand. GENERAL DESCRIPTION LHD vehicles combine certain characteristics of conventional front-end loaders and dump trucks, spe¬cifically designed for materials handling in underground mining and tunneling. The design intent is to provide one vehicle with one man, with the vehicle loading itself, hauling the load over level or inclined haulageways, and dumping the load. A typical production cycle of the most popular units has the operator driving the vehicle forward, forcing the bucket into the muck at or near floor level, and using the tractive effort of the vehicle and the prying action of the bucket to roll out and tilt back the load as shown in Fig. 1. With the bucket rolled back into the carrying position on the boom and the boom resting on the main frame of the vehicle, the load is hauled (trammed) to the dump point as shown in Fig. 2. At the dump point, the boom is raised, the bucket is rolled forward, and the load slides out as shown in Fig. 3. After dumping, the bucket is rolled back to the carrying position, the boom is returned to rest on the main frame, and the unit is driven back to the loading point for another load. There are two other types of LHD units that are slightly different in the cycles that they perform. One uses a hopper arrangement carried on the front of the machine, with a small bucket mounted ahead of the hopper. Several passes with the small bucket load the hopper, which is dumped by opening its floor. Al¬though this concept is several years old, it has gained less than 0.5% of the total market. The most recent LHD concept differs in that it has one bucket nesting inside another. The smaller inner bucket is loaded first, and it is then tilted back and above the larger bucket. When the larger bucket has been loaded, it is rolled back, and the total load is trammed to the dumping point. The dumping operation tilts the buckets in the reverse order from that of the loading operation. The impact of this new concept on the mining industry has not been measured yet. This chapter concentrates on the LHD vehicles employing the cycle described by Figs. 1 through 3, since these LHD units constitute an estimated 99% of the units in current use. MAIN VEHICLE FEATURES In general, the LHD vehicles available from most manufacturers share the same basic features.

Jan 1, 1982

By Rudrajit Mitra, Wesley B. Johnson, Erik C. Westman

The ability to understand stress redistribution within a mine allows greater extraction efficiency with reduced safety concerns. Stress redistribution has been examined at the laboratory scale using ultrasonic tomography and numerical modeling using PFC3D. A data acquisition system was built to obtain tomograms as samples are loaded in uniaxial compression. Limestone samples were loaded to failure. Three-dimensional tomograms of the samples correlate to various stress distributions. The tomograms are compared to analytical and PFC3D results.

Jan 1, 2005

By R. W. Sims

"He?s an SOB, but he's my SOB." Many of us have heard this line in reference to attorneys, and can appreciate the humor. However, the thought reflects a deeper attitude that lawyers should be used for attack purposes in the legal system or the regulatory process. Often, more permitting progress can be made with tact and flexibility than with inflexible, overly aggressive strategies. Usually, administrative hearings or other litigation work to the disadvantage of the applicant. Thus, I have concerns about approaching any permitting system with a hard-line attitude. On the other hand, the project team must always be prepared to defend permit applications and present a legally adequate case at public meetings, administrative hearings, or judicial proceedings. This paper discusses a number of strategies intended to increase the probabilities for successful permitting, whether opposition is informal or highly organized.

Jan 1, 1990

By J. Weyer

"A lot of incorrect, dangerous and misleading statements about the effect of CO2 on the human body can still be found in the internet, the media and in books. It is a fact that already low concentrations can lead to critical reactions, higher concentrations cause a narcosis. The real effect is not a lack of oxygen but an inner suffocation. The breathing reflex is decreased and the transport of oxygen in the blood is reduced due to a low pH value of the blood. Furthermore a reduced oxygen content in the air can also lead to the failure of diesel engines. MOTIVE Different gases can appear in active mines as well in abandoned mines, adits and caves. The most dangerous gases are CO, NO/NO2, H2S, SO2, CH4 and CO2. Although the general danger arising from these gases is mostly known some aspects are underestimated. Furthermore misleading or wrong statements exist about the detection and the effect of gases on the human body. This is especially true for CO2. In the last years a couple of accidents happened with a great number of injured persons and unfortunately also some fatalities. As a result wrong information and comments about the effect of CO2 have been published in the media. A huge unexpected CO2 outburst in a potash mine showed again some additional problems and limits for rescue troops. ORIGIN OF CO2 AND MISLEADING STATEMENTS ABOUT THE EFFECT ON THE HUMAN BODYCarbon dioxide can appear as free gas in the earth crust. It is especially known in significant concentrations in some potash deposits, in hard coal mines and some caves. Furthermore it can be formed due to complete oxidation of carbon. It can appear in technical processes. It is also used for or in technical processes, as fire extinguishing agent, as cooling agent, it is contained (added) in sparkling water or other soft drinks and it is formed by fermentation processes. Up to today a lot of wrong information about the effect of CO2 on the human body is published or is still in the mind of many people and unfortunately even in the mind of members or leaders of rescue troops. On August 16th 2008 a faulty CO2 extinguishing installation in the city of Mönchengladbach/Germany caused the injury of 107 people and the evacuation of further 150 people /1/. People on the streets became unconsciousness and felt down. Fortunately all could be rescued due to the immediate rescue operation of local fire fighters. Furthermore the CO2 concentration on the ground was diminished by help of a helicopter. What could have happen with the engine will be discussed later. After 6 days a second similar accident took place /2/. In the news members of the rescue teams explained that CO2 leads to suffocation due to a lack of oxygen. This is wrong! Also cave explorers often say that a burning candle can detect a low oxygen and/or high Carbon dioxide content in the air. This is also wrong and deadly dangerous! Similar statements we find nowadays in the internet /3, 4 and many other/. In a forum “science and mathematics > chemistry” several people say that winegrowers go with a candle into the vine-cellar to detect CO2 /5/. Again: this can be deadly! Another dangerous statement is that CO2 in higher concentrations leads to headaches so people should leave such areas. A last example found in the literature is that at 3 % the breathing volume is doubled and at a concentration of 20 % one can felt some warmth on the skin. Both is not wrong but can lead to false conclusions. /6/"

Jan 1, 2015

By P. D. Rao, D. E. Walsh, W. W. McClintock

A column flotation system was designed to conduct release analyses on a very finely disseminated, stratiform copper ore from the Denali Copper Prospect in Alaska. Chalcopyrite is finely disseminated in a carbonate matrix, and pyrite is disseminated in both the chalcopyrite and the gangue. Grinding to -20 µm is required for adequate liberation. A 25-mm x 2.4-m glass flotation column was designed. The ore and its flotation tailings were repeatedly floated to obtain a rougher concentrate. The rougher concentrate was then repeatedly floated to produce release fractions. These fractions were analyzed for copper, iron, calcium and magnesium, and release curves were plotted. The procedure was replicated at each of two grinds, i.e., 99% and 88% passing 37 µm (400 mesh). The procedure should find application for flotation characterization and process selection. Bond grindability testing was also conducted.

Jan 1, 1996

By Matthew Deutsch

A common casualty of modern openpit mine optimization is the assurance that the resulting design is actually achievable. Optimized mine plans that consider value and a bare minimum of precedence constraints do not, in general, translate into practical, operational mine designs that can be used in the field. Ultimate pits may come to a sharp point at the bottom. Schedules may require taking small parcels of material from many disparate areas of the pit in a single period, and grade control polygons may be ragged, narrow and not minable with realistic equipment. In this paper, these three fundamental openpit mine optimization problems are addressed by encoding them as maximum satisfiability problems. Maximum satisfiability provides a useful framework for problems that are nonlinear and may guarantee the optimality that metaheuristics cannot.

By Peter J. Suardini

Over the last few years, researcher have been working on improving procedures for fine-coal (minus 150 microns) washability analyses. The effort was stimulated by past difficulties in obtaining accurate and reproducible results from the various commercial laboratories providing fined washability services. This paper contains the results from fine-coal washability testing, performed by Process Technology, Inc. (PTI), as part of a U.S. Department of Energy (DOE)-sponsored project. The testing focused on comparing the performance of a number of media options (i.e., aqueous solutions and organic solvents), as well as evaluating the impact of a number of procedural steps on separation performance. The paper summarizes PTI's recommended washability procedures for various size fractions and ranks of coal, and makes recommendations for future studies of certain phenomenon, such as void penetration and particle density changes, which are not well understood.

Jan 1, 1995

By James R. Taylor

24.1-BASIC PRINCIPLES JAMES R. TAYLOR The basic principle involved in maintenance is protection of a company's investment through the care and upkeep of machinery and equipment, buildings and properties. Maintenance is justified through making available to the maximum extent possible the facilities, machines and services required by the operating and production departments in their function of insuring optimum return on investment. As the size, cost and complexity of the equipment used in modern mining and related industries increase, operating and production personnel become proportionately more dependent upon maintenance engineering for its contribution to the overall profit picture. A greater part of the total cost now is charged to maintenance and the maintenance group becomes a major company unit. Basic maintenance concepts have changed very little over the years, but the advances in methods and technique have brought about tremendous challenge and have in consequence assumed a greater influence and importance. The older "sledge- hammer" methods have given way to engineered and scientific systems, while the accelerating development of intricate equipment and machinery, and the instrumentation essential for control, demand an ever-increasing upgrading of maintenance personnel. Regardless of this growth in importance, cost and complexity of the maintenance function, it is important to remember that it is not an independent and self-sufficient unit, but is a necessary facet of the entire plant operation and is subject to the company's total production effort. As one part of a team, maintenance is successful only when functioning cooperatively wit11 the other departments it serves Close collaboration in all areas served by n maintenance group is essential if it is to function fully to protect the company's investment, whether the assets are in machinery, materials or people. 24.1.1-MAINTENANCE SCOPE Maintenance functions may be grouped into the two general classifications of primary and secondary. This grouping constitutes a basic division although, in practice, the scope of the maintenance activity varies in each mine or plant and is subject to differences in size and type of operations and company policy, plus the influence of precedent, which may be sectional or industry-wide. The primary functions supply the justification for the maintenance engineering department. while secondary functions are variable according to plant conditions and needs. The primary functions may be categorized as follows: 1. Maintenance of existing machinery and equipment. 2. Maintenance of existing buildings and grounds. 3. Inspection and lubrication of equipment and machinery. 4. Utilities generation and distribution. 5. Alterations to existing equipment and facilities. 6. Installation of new equipment and facilities. 7. Instrumentation.

Jan 1, 1973

By William S. Pintz, William A. Vogely, Charles J. Johnson

This chapter on the role of minerals in developing economies is oriented toward economic policy issues. The discussion and analysis cut across the technical, economic, legal, and policy fields. The goal of this chapter is to pro- vide relevant background information important to individuals involved with the minerals sector in developing countries. Where possible, trends are shown to provide a basis for understanding the evolving role of minerals in developing economies. This chapter is divided into the following five sections: (1) characteristics of developing countries (which presents selected statistical comparisons); (2) government objectives in developing countries; (3) government policy formulation in developing countries; (4) determinants of future trends, and (5) a summary of the chapter's major points combined with the authors' view. CHARACTERISTICS OF DEVELOPING COUNTRIES There are 155 nations in the world categorized as "developing countries." In total these nations represent about one third of the value of the world's mineral production, three quarters of the world's population, and over half of the world's land surface area. The group of so-called developing countries is quite diverse and there are exceptions to almost any general observation about the group as a whole. Most definitions of the term "developing country" are based on levels of per capita income. However, if per capita income is the sole criterion used in categorization, then several oil-exporting countries would jump from the category of developing country to the category of developed country.a Obviously, this results in a poor fit with respect to other measures. In general, the majority of developing countries can be characterized by relatively low per capita income, high population growth rates, high levels of unemployment, low levels of education, short average life ex- pectancies, income distribution skewed toward the highest 20% of the population, and a large share of exports represented by primary commodities. b For the purposes of this chapter a slightly modified version of the widely used World Bank system of classification (shown in Table 1.2.1) is used. As summarized in Table 1.2.1, developing countries are divided into three main groups based on estimated gross national product (GNP) per capita. It should be noted that the high- income, oil-exporting countries have characteristics of both developing and industrialized countries; however they are included for most statistical comparisons within the group of developing countries. Of the 155 developing countries in the world, approximately half produce minerals other than common building materials, and only 32 account for more than five percent of world pro-

Jan 1, 1985

By D. Malhotra, K. Purdy, G. Ramadorai

INTRODUCTION Today, flotation is clearly the dominant mineral concentration method. Since it is a relatively selective process, it is used for almost all sulfide minerals. A recent U. S. Bureau of Mines study indicated that approximately 225 million metric tons of sulfide ore was processed in 67 plants in the United States in 1980 (USBM Staff, 1981). There were over 100 plants processing copper ores in the world (Bassarear, 1985). Sulfide ores containing lead, zinc, copper, molybdenum, precious metals, cobalt, nickel, and iron are generally separated and concentrated by flotation. This chapter briefly reviews the plant practice related to the recovery of the above-mentioned sulfide minerals with emphasis on chemical reagents used for the production of marketable-grade products. PROCESSING OF SULFIDE ORES It is beyond the scope of this chapter to review the milling data for operating plants which have been extensively covered in literature (Tveter and McQuiston, 1962; Rausch and Mariacher, 1970; Weiss, 1985; Crozier, 1979). However, the following generalizations can be made regarding the processing of sulfide ores: 1. The primary grind is targeted to produce as coarse a product as necessary to provide an economic degree of liberation. 2. The concentration process, generally flotation, is designed to produce a concentrate consisting predominantly of valuable minerals and a middling fraction which may require further grinding to produce an optimum release of minerals. 3. The chemical reagent suite (collectors, frothers, etc.) for the separation of sulfide minerals from gangue minerals is generally complex. Total reagents used in the flotation process can be as high as six to eight, as is the case for lead and molybdenite separation from complex sulfide ores. 4. Chemical reagents are generally expensive because of the high selectivity for sulfide minerals. The process flowsheet is dependent on several factors, including ore grade and mineralogical composition. Generic process flowsheets for processing different sulfide ores have been developed for discussion in this chapter. However, there appears to be a consistent relationship between the reagent combination choice and the mineralogical composition of the ore (Tveter and McQuiston, 1962). These are covered in detail in the following sections. LEAD AND ZINC Galena (PbS) and sphalerite (ZnS), which commonly occur together, are the only minerals of lead and zinc, respectively, in most primary deposits. Feed ore grades are typically 1 to 5 percent Pb and 1 to 10 percent Zn. Very often economic quantities of copper and precious metals, silver and gold, also occur with these base metals.

Jan 1, 1986

By P. F. Mataich

"Why bother with computer control?" This question and others like it have been heard over and over again by those who have tried to convince operating men that there are sound merits to installing a process control computer. At IMC we have done a great deal of thinking and talking about computer control. In the course of these discussions the operating people have asked a number of questions about computer control. These questions and our answers to them make up the main part of this article. Obviously, the answer as to whether or not to go into computer control will be an individual problem conditioned by your company's circumstances. What I hope to do here is raise some questions, give you an idea of our thinking on the subject, and lay out some general guidelines for you to consider.

Jan 1, 1965

By J. Herbst, J. A. Kitchner, J. P. Anfruns, G. Poling

Measurements have been made of the rate of capture of single particles of strongly hydrophobic, surface-methylated, quartz, of sizes ranging from 12 to 40 pm diam., by single rising bubbles of diam. 0.5 to 1.1 mm. The results agree closely with the theoretically calculated hydrodynamic collision rates, indicating that, in this system, every collision results in capture and retention of a particle.

Jan 1, 1976

By W. E. Anderson

As part of a larger study to identify factors influencing the practical operating life of wire rope used on large draglines in surface coal mining, field trips to operating surface coal mines were made during late 1975. Wire rope performance information was obtained from personnel at thirteen mine sites west of the Appalachians. Seventeen pieces of equipment, utilizing buckets ranging from 30-to 220-cubic-yard capacity, were documented. We have judged that U.S. surface coal mining draglines, 30 yards and larger, can be represented as 120 machines having 60-cubic-yard buckets, moving 1.8 x 10 yards of overburden during 6,650 hours of productive availability per year. Based on our limited field study, we have calculated that downtime resulting from rope-related causes averages 105.6 hours per year for each (typical 60-yard) dragline. The total lost production from this source alone is thereby estimated at about 25 x 10 yards annually. Although study findings did not reveal anything about dragline rope life that wasn't known or practiced by one operator or another, most operators could expect improved rope life by periodic review of their practices and by adopting or adapting one or more life-improvement measures employed at other sites. Since rope productivity was found to vary by about five to one, among the sites studied, we believe considerably improved average performance is possible. As little as ten percent overall improvement would mean increased national productivity exceeding two million yards of solid overburden removal, and associated savings in rope costs alone of some two million dollars annually, not to mention any reduction of labor-related expenses. This report outlines preliminary findings which may prove useful to many operators in extending wire rope life, thereby lowering expenses and increasing surface coal mining productivity. Some of these modifications or adjustments in maintenance/operating practices would not require capital investment. We did not find anyone who had tried cost reductions by using presocketed dump

Jan 1, 1977

By G. W. Johnston

INTRODUCTION For many years mining at the Stobie mine of the Inco Metals Co. consisted mainly of fill-type mining for higher grade ores and block caving or blasthole open stope mining for lower grade ores. Open stope mining, although quite favorable in the initial stoping phase, has always presented problems in the pillar recovery phase, especially at depth. In 1966, sublevel caving was introduced. This method is ideally suited for low-grade ore and can be applied very successfully to intermediate or higher grade ores providing proper controls are enforced. Sublevel caving has three distinct advantages: it is highly adaptable to mechanization; it recovers the ore in one operation; and it provides adequate ground sup¬port and safety regardless of mining depth. This method does, however, make extra demands, particularly for new types of supporting services. The constant presence of rock makes quality control of the grade of the ore being extracted essential. Increased de¬velopment, different types of ventilation, roadways, and maintenance are only a few of the many changes re¬quired. The care and maintenance of the fleets of diesel equipment and the modification of equipment is a con¬stant challenge. CHOICE OF SUBLEVEL CAVING The question arises, why mine by sublevel caving? Fig. 1 shows a typical problem encountered by the open stope or blasthole mining method. Near the surface there is little or no ground support problem. As mining progresses to an intermediate depth, however, ground failure starts to occur in the supporting pillars. If open mining is carried beyond this point, the critical depth is soon reached, accompanied by hanging wall caving, ex¬tensive pillar failure, and the danger of losing control of the mining cycle. The rock caved from the hanging wall mixes with and dilutes the ore being extracted from the blasthole stopes. Ore losses occur when pillar failure pre¬vents drilling and development of part of the ore. The interruption to the mining cycle causes serious curtail¬ment in production until ground failure is controlled and the mining method changed to adapt to the new conditions. Having recognized the limitations of open stope min¬ing, alternatives were sought. The first alternative (Fig. 2) was to fill the open stopes with sand fill be¬fore extensive pillar deterioration occurred, recover the pillar ore by fill mining, and then convert to total fill mining below. If the ore grade is high enough it can support the costly fill method. Recovery will be at a much slower rate and will therefore extend over a longer period of time. On the other hand, sublevel caving gives complete primary mining recovery in a short time and is very adaptable to mechanization, which is now a necessity to combat spiralling labor costs and give greater produc¬tivity per man. Sublevel caving is ideally suited as a mining method for low-grade ore bodies which eventually reach a criti¬cal depth for open stope mining. DEVELOPMENT The development phase comes first and of course its main purpose is to gain access to the ore and provide a route for ore removal from the mine. Initially a 20% inclined service ramp is driven in the footwall rock (Figs. 3, 4, and 5). It is preferable to start at the top of a mining block and drive the ramp down¬ grade so gravity can assist in mucking the blasted de¬velopment round, and also access can be gained more quickly to the initial production area. The ramp nor¬mally turns at 3.1 rad (180°) about every 152.4 m (500 ft) to keep it reasonably close to the rock disposal

Jan 1, 1982