Search Documents

By Virgil W. Carmichael

In the Fort Union formation of western North Dakota, eastern Montana and northeastern Wyoming there are immense tonnages of lignite and subbituminous coal that have not yet been evaluated in terms of present economic conditions. Continued expansion of United States energy requirements has focused ever increasing attention on this tremendous resource, particularly as efficiency in mining and transporting of coal, as well as in electrical energy generation and transmission have improved and as hydrogenation and gasification of coal approach economic feasibility. This "total energy" concept for coal includes all of the energy uses that coal offers and has resulted in mergers of oil and coal companies and acquisition of coal re- serves by oil companies, as well as by coal companies and others. There is no doubt that these coals are entering an exciting new era of exploration and development that will result in greatly increased production. As a matter of fact, increased consumption for energy generation is well under way and recognition of the economic feasibility of high-Btu pipeline gas and synthetic petroleum products from coal is imminent. As coal is gradually displaced in steam electric generation by the more exotic fuels and processes, it will be increasingly used as raw material for the synthetic petro-chemical industry and the organic chemical industry.

Jan 1, 1968

By Fabian Laumen, Sunny Schoone, Felix Leaman, ELISABETH CLAUSEN

The acoustic emission (AE) technology has a high potential for flow characterization in hydraulic transport processes. For instance, in deep-sea mining, there are applications where manganese nodules are transported from the bottom of the sea to the surface or a transport ship. Here, an AE-based flow characterization system plays an important role to avoid the transport of non-related objects. However, the structural materials for the components of this system must be carefully selected to ensure resistance against corrosion and a good AE signal transmission. Therefore, in this experimental study, we evaluated the AE attenuation behavior of four different materials that can be employed in marine environments due to their properties. The results were obtained using thin plates and they indicate which materials have the highest and lowest attenuations. Moreover, we provide insights regarding the different wave modes that propagate on the plates.

Mar 2, 2023

By CLAIRE STREBINGER, ADITYA JUGANDA, JURGEN F. BRUNE, GREGORY E. BOGIN JR.

Methane gas explosions are a major risk in underground coal mining operations. The severity of such explosions can range from local area damage to massive loss of miners’ lives along with significant damage to mine infrastructure and ventilation controls that may lead to mine closure and loss of the entire operation. This study demonstrates the viability of integrating a computational fluid dynamics (CFD) combustion model into a longwall mine ventilation model to simulate methane gas explosions in the longwall face area. The resulting 3D methane gas explosion simulation can provide better understanding of the fundamental physics and the potential impact of an explosion in an underground longwall coal mine.

Aug 1, 2022

By D. K. Dysinger

The U.S. Bureau of Mines investigated leaching of chalcopyrite with sulfuric acid-oxygen under conditions anticipated during in situ leaching. A central composite experimental design was chosen to study oxygen pressures of 150, 300, and 450 psi, leach temperatures of 35?, 65°, and 95° C, oxygen-to-chalcopyrite mass ratios of 0.5, 1.0, and 1.5, leach times of 8, 16, and 24 hours, initial acid strengths of 0.6, 1.2, and 1.8 g H2SO4/g chalcopyrite and pyrite to chalcopyrite mass ratios of 0, 1, and 2. The leaching kinetics were consistent with the shrinking core model. A quadratic response surface model was used to determine linear and interaction effects of the design factors on rate constants from Arrhenius correlations.

Jan 1, 1993

By S. Shrivastava, R. G. Reddy

Spent potliner is generated in the electrolytic process of reducing alumina to make aluminum metal using molten fluoride electrolytes. Spent potliner(SPL) is obtained at the end of the pot's life. The SPL contains small amounts of cyanide and fluoride, which present environmental problems. Spent potliner could possibly be used as a fluidizer to replace calcium fluoride (CaF2) in the iron- and steelmaking industry and in the glass industry. A low viscosity and a low melting point are prime requirements for such an application. In the present study, viscosity measurements were performed. The effects of various additives, such as sand, limestone, dicalcium silicate dust and MgO baghouse dust, on the viscosity of SPL were studied. The results showed that the addition of sand and limestone can produce a very high fluidity SPL melt at significantly lower temperatures. The results suggest that spent potliner mixed with additives could potentially be used as a substitute fluidizer.

Jan 1, 2002

By L. Piga, P. Cipriani, F. Pochetti

High-temperature roasting of alunite in the presence of K2CO3 gives rise to a reaction that results in up to an 80% recovery of its potassium content as K2SO4 by leaching of the roasted mixture. K2SO4 is also generated from the reaction between the added K2CO3 and the SO3 driven off during roasting of the alunite. This limits the environmental and corrosive problems involved in the thermal treatment of this mineral. A solid residue containing mainly aluminum oxide is also obtained. This could be used as raw material for the production of aluminum, as the use of K2CO3 does not introduce different cations than are in the ore. A statistical study was performed on the factors assumed to affect the recovery of potassium, namely, roasting temperature, K2CO3- alunite stoichiometric ratio and leaching temperature.

Jan 1, 2000

By Lester A. D. Chin

The cost of bauxite is a multiple of the Bauxite Consumption Factor and the Unit Cost of Bauxite, and is a major cost item at most alumina plants. Bauxite Consumption Factor can be reduced by increasing alumina recovery during processing. Unrecovered aluminas are analyzed and possible research identified, using the framework below: 1. [Unextracted Aluminas] 1.1 Aluminous goethite 1.2 Boehmitic alumina 1.3 Diasporic aluminas 2. [Chemically-Bound Aluminas] 2.1 Desilication product 2.2 Phosphorus precipitate 2.3 Solid-phase lime-reaction products 3. [Alumina Reprecipitated on Red Mud] 3.1 Red mud separation and washing 4. [Physical Loss] 4.1 Liquor 4.2 Alumina dust

Jan 1, 1984

By N. Arbiter

Introduction The theoretical analysis of tumbling mill energetics and performance has largely neglected mill dimensionality, and, in particular, the importance of the length/diameter (L/D) ratio. This is in spite of the fact that practice varies substantially: geographically, for semi-autogenous and autogenous mills, as between North America and South Africa/Scandinavia, and historically, for overflow ball mills, for which the L/D ratio has increased significantly from the earliest small mills to the largest mills currently. The present study is concerned primarily with the influence of the L/D ratio on the design and operation of overflow ball mills, on the occurrence of the overload phenomenon, and on the limits, if any, it may impose on mill capacities because of critical pulp axial velocity limits. It will be shown that the shape factor is of major importance in this area and that its adjustment to the extent that this is practical should remove the diameter limitations previously postulated for this mill type. Dimensionality in mill design Ball mill shape factors in the period prior to 1927 (Taggart, 1927) averaged 1.1/1 for 29 center discharge mills and 1.0/1 for 30 peripheral discharge mills. With the resumption of new plant construction after the 1930s depression, the Morenci concentrator continued the 1/1 ratio with its 3.1 x 3.1 m (10 x 10 ft) mills. The ratio was increased progressively from then on, reaching 1.6 and 1.8/1 for the largest overflow mills currently. As shown recently (Arbiter, 1989), this is in sharp contrast to autogenous and SAG mill shapes, for which the ratio averages 0.4 in North America. On the other hand, South African practice, starting at the turn of the century with autogenous mills having 4/1 ratios, moved toward 1/1 until recently, when a 2.5/ 1 ratio mill was installed. The reasons given for such divergent practice for mill shape factors are in some respects contradictory and generally inconclusive. The most complete discussion from a practical viewpoint (Dor and Bassarear, 1982) is limited to primary SAG and autogenous mills. Considerations of ball mill dimensionality have had a twofold direction. On the one hand, it has been argued that ball mill efficiencies should increase with increasing diameter and that the specific energy for a particular grind should be reduced accordingly. An inadvertent test of this idea at the Bougainville operation (Burns and Erskine, 1983) resulted in drastic underpowering, which led to failure to reach design capacity until additional mills were installed. This can be taken as strong evidence against any increase in efficiency with diameter. In another direction, it has been argued (Arbiter and Harris, 1982, 1983) that there is a limit to ball mill diameters because of the demonstrable limit to axial flow velocities evident in the overload phenomenon, which as a fact is incontrovertible. But that it places a limit on mill diameters overlooks the evidence given below that appropriate variation in the L/D ratio will permit major increases in diameter, limited only by constructional or economic factors. The present study was directed toward quantifying the overload phenomenon through examination of the influence of mill dimensionality variation and mill operating variables on its occurrence. It is shown that varying the operating conditions, specifically the load fraction and the fraction critical speed, can reduce the risk of overload for existing operations; while appropriate decreases in the L/D ratio can minimize the risk in the design of new circuits. Ball mill overload Ball mill overload is a consequence of the approach to a critical velocity with increasing feed rates or circulating loads. Although the effect has been known for over 50 years, there have been no previous attempts to quantify it. The following description of the ball mill as a flow system is the preliminary to a quantitative analysis: 1) In the absence of a ball load, axial flow of pulp through a mill resembles open channel flow, except for disturbances near the shell due to shell/lifter rotation. 2) For a given ball load (Lf), the void fraction available for pulp hold-up (H) for the ascending portion of the load is approximately 0.4 Lf. In the descending portion, it is greater than this and increases with fraction critical speed (Fc) because of load expansion. 3) Increasing the feed rate increases pulp hold-up and progressively fills the available void space. At a critical flow rate, which depends on system geometry, hydraulic head and pulp rheology, void filling reaches its limit; a pool forms rapidly and fills available space outside the ball load and up to the overflow level. Prior to this, pulp discharges mainly along the ascending rim of the overflow. 4) For a small mill (Lo et al., 1990), it has been shown that with increasing feed rates the critical filling is at or near 50% of the mill volume. Power drops rapidly when this level is reached, as required by the torque formula. 5) The transition to overload is associated with the following phenomena: a) The decrease in power draw. b) Damping of mill sound. c) Reduced comminution of coarser feed sizes, probably due to reduced direct impact in the presence of a pool. d) Increased circulating loads, which further intensify the overload, and increased density of cyclone underflows, which can lead to roping. e) Conditions beyond overload are not known because feed rates are not delibelrately increased beyond this point. f) The existence of the phenomenon limits the capacity of a mill with a fixed set of operating conditions and can prevent the balancing of hard ore feed rate decreases by increases in soft ore rates.

Jan 1, 1992

By Donald Babbitt

In 1971, during the planning and design stages of a $300 million expansion, the Iron Ore Company of Canada Ltd. through its Engineers, Canadian Bechtel Ltd., came out with a preliminary request for two (2) 10,000 LTPH belt conveyor scale systems. These Systems were to provide weighing accuracies within 2.5% of the iron ore pellets and concentrates in transit on two (2) 72" wide conveyors from the stockpiles to the ships. Each conveyor system would be fed by a rail mounted bucket wheel reclaimer, with the conveyed material moving directly to the ship loaders with no inter- mediate surge and/or storage bins between the stockpiles and the ships. The bucket wheel reclaimer discharge rates would vary from 0-9600 LTPH in cyclic periods, with the periods varying from 1-5 minutes - dependent on the level of the reclaim buckets in relation to the stockpile as well as the slewing rate of the reclaimer. There would be frequent interruptions for bucket wheel repositioning (laterally and vertically), changing ship holds, and trimming ship holds. These frequent zero flow conditions, approximately 500 per 150,000 ton ship, could last 1-5 minutes. In addition, the conveyors on which the scales were to be mounted would be over the water and subject to the wind and cold of Northern Quebec. These Systems would be in use 350 working days of the year and would load 30,000,000 LT/yr. (An average of 90,000/working day).

Jan 1, 1975

By Gary Peach, Khalid Saif Al-Khayareen, Vigil Fernandez, Furqan Hameed

The Musaimeer pump station and outfall project (MPSO) is in Doha Qatar. This technical paper will discuss and explain the three major stages of geotechnical investigation employed. Stage one the tender geotechnical data and how this was used to design the TBM and identify various areas of risk. Stage two was the selection of supplementary geotechnical investigation methodologies. Stage three was the geotechnical investigation by specialist equipment installed on the TBM and providing further data on a real time basis as the TBM was advancing. Analysis of all the data will be provided along with the lessons learned.

Jun 23, 2024

Dunn has written an excellent paper providing a wealth of advice on what is often the most costly consumable in the mineral processing plant. As he pointed out, grinding media selection and quality control can play a major role in successful plant operation. Owing to the economic importance of this topic, there are some important factors related to media sizing that I believe merit further comment. Dunn made reference to a slightly simplified version of the Azzaroni (1981) equation and pointed out its successful use for the Henderson SAG and Climax ball mills.

Jan 1, 1991

Maptek I-Site laser scanning expertise and software technology is being used to map the geology and layout of the deepest underground laboratory to be established in the U.S. The Deep Underground Science and Engineering Lab (DUSEL) in the former Homestake gold mine in Lead, SD, will provide for scientific studies in particle and nuclear physics, geology, hydrology, geo-engineering, biology and biochemistry. The project, funded by the National Science Foun¬dation (NSF), will allow geoscientists and engineers to research the behavior of subsurface rock, minerals, water and energy sources

Jan 1, 2010

By John G. Reid

Geologists, employed by the Australian Company, Metals Exploration Limited, discovered nickel laterite enrichment at Greenvale in 1967. A joint venture was arranged with the Freeport Minerals Company who had gained early experience with nickel laterite ores when building and operating the Nicaro and Moa Bay Treatment Plants in Cuba. A 5 tonne/day Pilot Plant at the Freeport research facilities at Belle Chasse, Louisiana, verified the amenability of the ore to treatment by the reduction and ammonia-ammonium carbonate leaching process used at Nicaro. A 5 800 tonne/day Treatment Plant was constructed on the coast at Yabulu, North Queensland. This paper describes the ore body, the mining operation and the stages of treatment required to produce nickel oxide products and a mixed nickel/cobalt sulphide product at Yabulu.

Jan 1, 1979

By Bror Nyman

Wide settlers are a way to decrease the linear velocities of advancing liquid phases. It has, however, been found unnecessary to risk a proper settler performance by building shallow settlers in order to avoid a so-called interface turbulence due to a too big difference between the linear velocities of the organic and the aqueous phase. This conclusion has been reached from tests using a large transparent settler model, where the behaviour of a clean interface between two advancing liquids has been investigated. Also in a more realistic case, making an organic in aqueous or an aqueous in organic dispersion to move between the liquid phases, no obstacle has been found to use a somewhat more deep and correspondingly ore slowly t10wing aqueous phase. Based on above findings, support can be given to a new trend to build the settlers slightly deeper than what has been typical for the so-called low-profile design. In this way, it is much easier to avoid an excessive air introduction and other severe difficulties, like those caused by crud moving from one stage to another. It is further shown, how gravity can be used to slow down and distribute a dispersion being fed into a settler of a VSF unit. Entrainment levels have been found to be reduced by a careful design of primary dispersion distributors and picket fences of the settler. Finally, it is demonstrated, how outlets from the side of the settler can be used to simplity interstage pumping and to decrease the rotation speed of any pumping device.

Jan 1, 1996

By Scott A. Norby

Kennecott's Ray Mines Division (RMD) is located in central Arizona. The pit and silicate plants are located at Ray while the 27,500 tpd concentrating facilities are located at Hayden, approximately 20 miles away from the pit. Ore is delivered in 100 ton railroad cars, 60 cars per train via the Copper Basin Railroad. The side discharge cars are dumped into a 6,000 ton trackhopper. There are 6 Nico feeders, two per belt. Three 48" belts transport the -8" ore to three 7' standard (secondary) Nordberg crushers. Each crusher is preceded by a 6' x 12' Tyler double deck screen. The secondary crushers are open circuit. The -1/21t material from the screens is transported directly to the fine ore bin at the mill. The discharge from the crushers and the intermediate product -2 1/411 x +1/2" is conveyed to a surge bin. The tertiary crusher feeder belts discharge onto five 61 x 161 Tyler double deck screens, each followed by a 7' shorthead (tertiary) Nordberg crusher in closed circuit. The -1/2" product joins the -1/2" ore from the secondary crushers and both are conveyed along a 42", 4,230 foot long belt to the fine ore bin that feeds the grinding circuits. When hard ore is experienced at the concentrator the daily throughput decreases by up to 10%. This coupled with the fact that the ore is generally becoming harder with mine depth provided the incentive to improve the performance at the crushing plant.

Jan 1, 1986

By Willard C. Lacy

INTRODUCTION A program to insure adequate talent for development and management of our mineral resources entails two equally important and interrelated aspects: 1) attracting and retaining promising student talent, and 2) providing a first-rate education for those entering careers in mineral science and engineering. Manpower shortages have eased in many areas of engineering, particularly in those areas dependent directly or indirectly upon government contracts in space and war programs. However, in the minerals industry the needs still remain critical. As increasing concern over preservation of the environment has developed, the political and social reaction was to seek out major offenders, to look for "whipping boys" -- and the mineral industry was, and had been, an offender. It was there for everyone to take pictures, it couldn't be covered up, and the Department of the Interior lashed away in the beautiful and popular brochures: Quest for Quality, The Third Wave, The Population Challenge, and Surface Mining and Our Environment (Ravaged Land). The Sierra Club, the Field and Stream magazine, TV, and daily news media added their lashes. In the minds of our social-conscious youth the mineral industry took on the image of "exploiters" of natural resources; "polluters" of streams, lakes, and the atmosphere; "despoilers" of wilderness areas and scenic beauty -- a plague to combat, rather than an exciting challenge that entailed exploration of the remote, conquering of the primitive, and developing of the undeveloped. Enrollments declined and many traditional mineral engineering curricula were abolished or Integrated into other stronger engineering departments to meet student-faculty ratio requirements.

Jan 1, 1971

By L. Whitby-Costescu

The Shebandowan mine and concentrator, with a capacity of 9072 t/week (10,000 st per week), was opened in 1972 after several years of environmental study and planning. The mine is located in a popular vacation cottage .area about 96 km (60 miles) west of Thunder Bay, Ontario. Undertaken before environmental assessment procedures had become an established requirement, Shebandowan is one of the first Canadian examples of effectively integrating environmental work into overall planning. Although it is an underground mine, many of the environmental considerations are common to open-pit operations, and hence, it provides a case history for the use of all mine planners. Computers can play a part in such studies by simulating the annual production of mine wastes, by on-line polling of environmental sensors and by processing sensor data. Early attention was focused on establishing base-line conditions in a two-year water quality monitoring program. Since production began, water quality monitoring has shown that mining has not caused any significant changes. However, mine drainage disposal arrangements had to be modified in the light of operating experience. There is no townsite associated with the mine, and workers commute from established municipalities. Harmonious relations have been achieved with local cottage residents after their initial fears were dispelled. Plans are ready to begin revegetating the tailings when a sufficient area of dry elevated tailings has been accumulated. Rehabilitation of the land disturbed during development was begun before start-up and was completed during initial operations.

Jan 1, 1979

By D. L. Whiting

Dump leaching and ,in-situ solution mining have received considerable attention during the past few years due to their apparent economic viability and minimal environmental impact. Solution mining actually dates back to the 17th century when leaching of copper ore was first reported. However-, modern day leaching didn't begin on a wide scale until the mid-1900's. In-situ mining for copper, nickel, salts, and oil shale is currently looking more attractive as the technology advances. Presently, about 15 percent of the copper production in the United States is from leaching operations at approximately 14 active sites, the largest of which are the waste dumps near the Bingham Copper Mine, Utah. To establish a common background, the discussion is centered around state-of-the-art conditions. For dump leaching, complications inherent to the physical conditions and chemical reactions such as channeling, porosity and permeability, sorption, air flow, rock alteration and pH control are discussed. Emphasis is made on those conditions which render solution recovery rates and solution mineral concentrations unpredictable. By illustrating typical and actual field conditions, the generally accepted flow theories for both dump leaching and in-situ solution mining, including rubblization, are presented. For in-situ mining, hydrogeologic techniques such as geophysical well logging, aquifer testing and digital computer modeling are also discussed. The importance of artificial fracturing and well stimulating to solution injection and recovery is made with regard to project development. Finally, the subject of water pollution control techniques and the potential impact of the

Jan 1, 1977

By W. Hoecker, S. Watson

The use of oxygen (Goldox™) in gold leaching has emerged as a significant modification in the past nine years. The Goldox™ process was ori gi na 11 y developed by Afrox Ltd ( part of the BOC Group) and is currently used in South Africa, Australia, Canada and the United States. Although a variety of benefits have been observed with oxygen, this paper out 1 i nes the main ones with reference to Australian plant data. The case studies were categorised into the ore type: Oxide, blends and primary ore.

Jan 1, 1992

By Ian J. Corrans, Gary Johnson, John E. Angove

Activox® is a hydrometallurgical process used to oxidise sulphide concentrates. The process is based on two relatively simple, established unit operations; i.e. fine or ultra-fine milling (UFM) and pressure oxidation under mild conditions. An under-standing of, and ability to control the pulp chemistry during oxidation has resulted in the successful Activox® treatment ( on a batch scale) of a wide variety of sulphide flotation concentrates; • pyrite/arsenopyrite + gold • pyrite/chalcopyrite + gold • pyrite/chalcocite + gold • pyrite/enargite/tetrahedrite + gold Oxidation rates are rapid (1-2 hours retention time) and gold

Jan 1, 1995