Search Documents

By A. G. Moon

Kennecott Copper Corporation's Chino Mines Division concentrator is located in Hurley, New Mexico. Construction of the concentrator was started in 1910 and its capacity was progressively increased over the years to the present nominal 20, 425 t/d of ore (22, 500 stpd). The principal copper minerals present in the ore are chalcopyrite and chalcocite with much of the chalcotite intimately associated with pyrite. Lime is used to depress pyrite, and flotation at a high pH or alkalinity is required for optimum recovery of chalcocite with good rejection of the pyrite. Regrinding is also required to liberate chalcocite-pyrite middling grains. Accurate control of the lime addition is necessary to obtain both optimum metallurgy and minimum lime usage. At low pH levels, flotation cell control is difficult due to excess froth, but excessively high pH levels can go unnoticed because froth characteristics do not change from those experienced at the deisred pH. With manual control of the lime addition, the desired pH can be exceeded for periods of up to two hours. In 1972 a major renovation of the flotation and regrinding circuits was com¬pleted and at that time a new lime distribution and control system was placed in operation. Limestone is obtained from a nearby quarry west of Hurley. The limestone is crushed, sized and fed to a rotary kiln and the quicklime product is stored prior to slaking. The lime is slaked, as required, in a mixing tank-classifier type slaker and the lime slurry is pumped to a concentrator storage tank from which it is distributed through a conventional closed loop system. The current average lime usage rate is approximately 6 kg/t of ore (12 lb per st).

Jan 1, 1976

By M. A. Reyes, L. Yan

Heat and humidity buildup within refuge alternatives (RAs) may expose occupants to physiological hazards such as heat stress. The Mine Safety and Health Administration (MSHA) regulations require RAs in underground coal mines to provide a life-sustaining environment for miners trapped underground when escape is impossible. RAs are required to sustain life for 96 h while maintaining an apparent temperature (AT) below 95 °F (35 °C). The National Institute for Occupational Safety and Health (NIOSH) tested a 10-person tent-type RA, a 23-person tent-type RA, and a 6-person metal-type RA in its underground coal mine facilities to investigate the thermal environment over a 96-h period. The test results showed that mine air and mine strata temperatures surrounding an RA occupied by simulated miners (SMs) increased over the 96-h test period. The test results suggest that RA manufacturers should consider this increase in temperatures when calculating and evaluating RA components during surface and laboratory tests. The findings can equip stakeholders with additional considerations for calculating the interior heat and humidity temperature profiles for occupied RAs not tested in situ

Nov 22, 2019

By Tae-kyeong Yeu, Cheon-Hong Min, Hyung-woo Kim, Sup Hong, Minuk Lee, Chang-Ho Lee

This paper concerns the optimum arrangement of the buoyancy module, which is used for stable dynamic motion and structure stability of the marine flexible riser. The main method of this study is simulation-based design using Genetic Algorithm (G.A) for optimum design and Multi-body dynamic for simulation. The marine riser connects the vessel and the seabed-tracked vehicle. The motion of the riser affects the motion of the vessel and the vehicle. In this study, a marine riser of the deep-seabed integrated mining system (Figure 1) is used. This riser has a strong effect on efficient transfer of minerals. So, the buoyancy module must be equipped to supplement problems of the structure stability and the dynamic motion. Positions and quantities of the equipping buoyancy modules are determined by the at sea experiment (Figure 2). But this method is not easy because the actual sea experiment is expensive, time-consuming and dangerous (Figure 3). Thus, the position and quantity must be determined by simulation-based design. The dynamic analysis models of the riser and the buoyancy module were built in the commercial software DAFUL. In the marine environment, factors affecting behavior are current, drag force, etc.

Sep 1, 2014

By Derek. C. Arnold

In order to meet increasing demands for water supply in the next millennium, the Government of the Hong Kong Special Administrative Region have identified the need for a major new water treatment and transfer scheme. The project now under construction will comprise a 1.2 km long raw water aqueduct, a major new 0.25million cubic metres per day water treatment works (with space for upgrading to 1.2Mm³/d), a 12.1 km long treated water aqueduct and a primary service reservoir. In order to meet increasing demands for water supply in the next millennium, the Government of the Hong Kong Special Administrative Region have identified the need for a major new water treatment and transfer scheme. The project now under construction will comprise a 1.2 km long raw water aqueduct, a major new 0.25million cubic metres per day water treatment works (with space for upgrading to 1.2Mm³/d), a 12.1 km long treated water aqueduct and a primary service reservoir.

Jan 1, 1999

By Bhaskar B. Thapa, Michael T. McRae, Johannes V. Greunen

This paper describes the preliminary design of the fourth bore of the Caldecott Tunnels along State Route 24 in Oakland, California. The paper focus is on two major aspects of the project: initial support system design and seismic design. The initial support system was designed based on the New Austrian Tunneling Method (NATM).NATM provides the required flexibility to accommodate the variable ground conditions in the weak, folded, and faulted rock along the alignment. The seismic design provides a final lining system that meets serviceability requirements for a 1,500 year seismic event with an estimated peak ground acceleration of 1.2g.

Jan 1, 2007

By LeRoy D. Loy

Would you believe me if I told you the constant battle between Government regulatory agencies and industry could be won by both sides? No, I'm not crazy, nor have I been soaking up any of that fine Kentucky whitelightning. But I have recently been a participant in a battle where both sides won. Actually, I'm using the term "battle" loosely because, in reality, it wasn't a battle at all - despite the fact that all the ingredients were there for a monumental struggle; i.e.. government, industry, special interest groups and a controversial issue - the development of effluent limitations. I'd like to tell you about it. Historically, on one side of the battle, government has always been ac¬cused of adopting regulations with limited evaluation of existing technologies; and then with seemingly no regard for the economic consequences. On the other side, industry gets punished by government's harsh actions because of their past "do-nothing" attitude toward pollution control. Recently, this battle seems to be losing steam, because both government and industry are beginning to realize that, ultimately, they both will lose. Even more important is the fact that both sides are, or should be, working for industrial expansion compatible with environmental protection.

Jan 1, 1977

By M. J. Gilbey

London Underground is the oldest and one of the deepest Metros in the world. The temperature of the Underground has been increasing over the last 100 years, mainly as a consequence of increases in train service. Further increases in train service are planned in the coming years to meet the predicted growth in passenger demand. Unabated, the additional service will increase temperatures on the Underground. London Underground Limited (LUL) has therefore set up the Cooling the Tube Programme (CTP) to tackle the issues of thermal conditions on the Underground. Some of LUL?s studies and cooling methods have borrowed experience and techniques from the mining industry; some of methods used or proposed may in turn be of interest to the mining community. This paper presents a background into the sources of heat on the Underground network, the manner in which the heat is presently dissipated, the analysis of future temperatures and criterion and a number of means and methods being used or proposed to cool the network in an environmentally sensitive manner.

Jan 1, 2009

By Steve Kral

The mining industry has had three difficult years. Commodity prices have remained low and investor confidence in the industry has been shaken. And even though the Asian economy appears to be improving, it will be some time before this improvement will translate into better commodity price conditions for mining. In addition, increased environmental and social restrictions that have been placed on the industry in developed and developing countries have made mining a more difficult proposition. And, if that is not enough, the global mining industry has found itself in fierce competition with Internet businesses for investor capital. Despite that gloomy picture, more than 10,500 mining industry professionals from about 70 countries gathered in Toronto, Ontario March 5-10, 2000 for the Mining Millennium 2000 conference. This meeting was a joint effort between the Canadian Institute of Mining, Metallurgy and Petroleum(CIM) and the Prospectors and Developers Association of Canada (PDAC).The joint meeting also featured two trade exhibitions and more than 150speakers. PDAC’s trade show attracted about 400 exhibitors and an additional 200 in the concurrent Investors’ Exchange. CIM’s exhibition attracted about 600 equipment and service companies.

Jan 1, 2000

By S. S. SHINDE, P. C. JIKAR, N. B. DHOKEY

Mill scale is an oxide waste product of steel mills, containing around 70 percent iron and other allied impurities. In the present context, a dynamic prototype counter-current reactor (CCR) was used for the experimentation and simulation of a particle bed using the discrete element method (DEM). Mill scale was pulverized to ASTM mesh range 140 (106 μm)/+ 270 (53 μm) and oxidized in a CCR to make a single oxide Fe2O3 phase by maintaining the required thermodynamic conditions, such as pure oxygen at 1,100 °C. This oxidized powder was then subjected to a reduction reaction in the CCR, with gas mixture (H2:N2) ratio of 1:4 at 875±5 °C for filling degree, fd , and reactor revolution, ω, ranging from 5.38 to 16.14 percent and 2 to 5 rpm, respectively. A creeping fluid flow condition (Re < 1) and natural heat convection (Gr/Re2 >> 1) were maintained during the solid–gas reaction, and the particle-bed behavior was quantified by Froude number for the optimum operating window. The simulation was validated with the experimental results of reactor reaction product by X-ray diffraction (XRD) and scanning electron microscope (SEM) images.

Worldwide minerals exploration slipped in 1992 from 1991 levels. Although industrial production figures showed the US economy emerging from recession in early 1992, it was not until February 1993 that the lagging indicator of unemployment dropped to 7%. Most other industrialized countries are still in recession. Preliminary data for 1992 showed industrial production dropping in Japan (5%), Germany (1.4%), the United Kingdom (0.5%) and France (1.4%). The slowdown in industrial production led to reduced mineral demand. This resulted in lean cash flows from mining operations, which squeezed exploration funding. Although mineral prices were steady during most of 1992, some mineral commodity prices began falling in late 1992 and early this year. Exploration 1991-1992 According to Metals Economics Group (MEG), planned 1992 exploration expenditures were down by about 5%. Geographically, the leading exploration target was the United States with 21 % of the expenditures, followed by Australia (19%), Canada (18%), Latin America (15%), South Africa (9%) and the western Pacific (7.5%). The remaining 10% was split between Europe and Africa. There were absolute increases in exploration expenditures in the United States and Latin America. Latin America showed the largest increase. The change in the Mexican mining law allowing foreign ownership of mines should result in the inflow of direct foreign investment in Mexico&apos;s mining industry.

Jan 1, 1993

By Taghi Sharizadeh, MAURICE SUNKPAL, ELAHEH TALEBI, PEDRAM ROGHANCHI

Excessive heat exposure is among the health and safety hazards that have adverse effects on the mine workers. The very nature of the underground climate makes it a convenient avenue for heat generation and accumulation from several heat sources including autocompression, equipment, and heat from strata. This study investigated the effects of clothing insulation and acclimation on the thermal comfort ofmineworkers who are exposed to heat in underground working environments. Several clothing ensembles have been considered to analyze the effect of the thermal resistance of clothing on the thermal comfort of workers. To investigate the impact of the clothing insulation, the thermal comfort limit of an underground miner was calculated in the form of maximum allowable exposure time for an 8-h shift. Parametric analyses were subsequently performed using an already developed thermal comfort model using MATLAB software. The results demonstrate that clothing insulation has a significant effect on the thermal comfort of mine workers. Increase in the clothing insulation decreases the maximum allowable exposure time of mine workers. This is especially true for the new and non-acclimated workers. Since acclimatized workers can tolerate a higher level of the dehydration and are capable of losing more water by sweat per shift, the maximum allowable exposure time for the acclimated workers are higher than non-acclimated workers. These analyses have shown that acclimated workers can have more continuous work per shift compared with non-acclimated workers. For example, in an environmental condition with clothing that a nonacclimated worker cannot work more than 5 h, an acclimated worker can work a full 8-h shift.

Jun 29, 2020

By James F. Kvitkovich, George V. Weisdack

Editor’s note: This is the second part of a two-part series on longwall mining in the United States. Part one was published in the December 2005 issue of ME (pp. 21-26). It provided a history of longwall coal mining in the United States. It also discussed the technology involved in the productivity gains and operational improvements. Boyd anticipates that U.S. coal production will increase by 61 Mt (67 million st) (6 percent) from 2004 to 2010. A combination of higher surface and underground mine production will be required to meet the projected market demand. Boyd’s projections of coal production by major mining methods are shown in Table 1.

Jan 1, 2006

By R. R. Oder, R. E. Jamison, E. D. Brandner

This paper presents preliminary test results obtained with a 0.38 kg/s (3000 lb-hr) beta prototype MagMill™. In processing Upper Freeport coal the beta prototype recovered 82% of the weight of the feed and 91% of the heat content while reducing the potential emissions of sulfur, kgSO2/GJ(lbSO2/MBtu), by 61%. Pyritic sulfur in the MagMill™ product was reduced by 78% compared to that in the feed. For all runs, the mill product was controlled between 70 to 80% finer than 74 µ particle size. Recoveries of mercury, arsenic, and selenium ranged from 35 to 45% of that in the feed. Power draw was reduced by 26% and mill throughput was increased by 9% compared to the pulverizer operating with no magnetic separator attached.

Jan 1, 2000

By C. Wen

In Huoqiu region of Anhui Province, Fe2O3 occurs mainly in the form of specularite. Besides quartz, the gangue minerals include iron-bearing silicates such as chlorite and sericite which account for about 10% of the total gangue. The separation effect of conventional collectors is poor in the flotation of the minerals, that is, the average grade of iron concentrates is only 60-62%. Using the developed amphoteric collector can successfully realize not only the separation of specularite from various gangue minerals with results of iron concentrate grade above 65% and iron recovery of above 80% but also low temperature flotation at 15°C.

Jan 1, 2012

By Wayne Trudel, Eric Saderhold, Lloyd McEvers, Lori Clarke, Charles Lynn Bolin, Leroy Schutz

Editor’s note: This is the second part of a two-part series on how mine geologists added about 141t (4.53 million oz) at Newmont Mining’s gold operations in Nevada during 2003. Part one (ME, July2004, pp. 19-26) showed how cross-functional teamwork among mine geologists, engineers, metallurgists and operators added $65 million in revenues at Newmont’s Gold Quarry Mine. Part two deals with how this same cross-functional team added about 25.8 t (830,000 oz) of gold reserves and two years of life at the company’s LoneTree Mine. This was done through improved reconciliation methods, pit optimization designs and updated geotechnical parameters. Part two also discusses how Newmont’s Nevada mine personnel added about 62.2 t (2 million oz) of gold reserves at its Twin Creeks Mine, extending the mine’s life by several years. The Lone Tree Mine is a sediment-hosted, micron gold deposit. It is dominantly situated in the Golconda thrust footwall. The north-south trending Wayne Zone fault controls the highest-grade ores and

Jan 1, 2004

By L. F. Ruppert, P. A. Freeman, R. C. Milici, S. J. Tewalt, L. J. Bragg

The U.S. Geological Survey has completed a dig-ital coal resource assessment of six of the top-producing coal beds and coal zones in the northern and central Appalachian Basin coal regions. These include the Pennsylvanian-aged Pittsburgh, Upper Freeport, Lower Kittanning, Fire Clay, Pond Creek, and Pocahontas No. 3 coal beds and coal zones. Resources were calculated on all of the coalbeds/zones, with the exception of the Lower Kittanning coal bed. Preliminary original resources are estimated at about 93 billion short tons (84 billion tonnes), of which about 66 billion short tons (60billion tonnes) remain. Much of the remaining coal in all five coal beds/zones is thinner [<3.5 ft (1.07m)] and deeper [>1,000 ft (305 m)] than the coal that has been mined, but economic resources are still available and mining in each coal bed/zones will continue throughout this decade and into the next given current market conditions.

Jan 1, 2001

By H. H. Murray

The largest reserves of palygorskite in the world are located in Anhui and Jiangsu Provinces in East Central China. The deposits are Middle Miocene in age and range from 3 to 6 m in thickness. The deposits are the alteration product of basaltic volcanic ash. The Chinese Geological Survey estimates the palygorskite reserves are in excess of 200 million tons. The elongate particle shape results in unique colloidal properties. Large quantities are exported to Japan, Taiwan, Southeast Asia, New Zealand, Australia, and West and Gulf Coasts of the United States. The markets include agricultural carriers, paint, joint tape compounds, animal feed binders, catalyst support, drilling muds, and suspending agents for chemicals, pharmaceuticals, and medicines. The viscosity is high and the quartz content is generally 5% or less.

Jan 1, 2009

By R. Q. Honaker, D. P. Patil, A. Sirkeci

Due to increased production of fine coal during mining during this century and inefficient fine coal recovery technologies, a vast reserve of high quality coal currently exists in refuse ponds. A novel fine coal circuit consisting of a hindered-bed classifier, an enhanced gravity concentrator and a flotation column has been evaluated for the recovery of fine coal from refuse ponds. The treatment of a pond derived from Pittsburgh No. 8 seam coal resulted in the production of a premium fuel containing less than 5% ash and a calorific value of about 30,173kJ/kg with 60% mass yield. The results from the treatment of two refuse pond materials will be presented in this publication.

Jan 1, 2000

By T. A. Rundle, K. Kim, W. M. McCabe, E. C. Gregory

Overcoring tests were conducted at the Near-Surface Test Facility(NSTF) to assess the suitability of five techniques (U.S. Bureau of Mines borehole deformation gauge (BDG), Commonwealth Scientific and Industrial Research Organization (CSIRO) hollow inclusion stress cell, Luleå triaxial gauge (LuH gauge), and Council for Scientific and Industrial Research (CSIR) doorstopper) for in situ stress determination in a closely jointed basalt. This effort is in support of the Basalt Waste Isolation Project, which is studying the feasibility of locating a nuclear waste repository in the basalts of the Hanford Site in southeastern Washington. This paper presents the results from the overcoring study that formed the basis for selection of two techniques to be used during the further exploration of the basalt formations at depth.

Jan 1, 1983

By Hyung Jeek Kim, Jongmin Joo, Jonguk Kim, Jai-Woon Moon, Kyeong-Yong Lee

"Co-rich ferromanganese crusts (Fe-Mn crusts) distributed on seamounts in the western Pacific are potential economic resources for cobalt, nickel, platinum, and other rare metals in the future. Evaluation and selection of a mining site can be established based on abundance and grade of Fe-Mn crusts in the site as well as topography that should be smooth enough for mining operations. Therefore, acquisition of shipboard echo-sounding and acoustic backscatter data are prerequisite to the selection of potential mine sites in addition to visual and sampling operations. Acoustic backscatter data can be used to locate crust-covered areas on a regional scale with the understanding of acoustic properties of crust through its correlation with visual and sampling data.During an expedition that took place from January to March 2014, KIOST collected geophysical and geologic data to assess the resource potential for Fe-Mn crusts on three seamounts (guyots) in the Western Pacific. In OSM11, one of the three surveyed seamounts, three camera tows were performed to observe the distribution of Fe-Mn crusts on the summit and slopes of the seamount. Although sediments of various thicknesses generally cover most of summit region of OSM11, several regions with high backscatter signals occur on the periphery of the summit. The occurrence of Fe-Mn crusts, observed during the camera tows, on those high backscattered regions suggests that the backscatter signals of shipboard multi-beam sonar can reflect changes in the geology of the seafloor from sediment layer to Fe-Mn crust deposits. The Fe-Mn crust deposited around the summit region is worthy of notice because of its topographic characteristics, including shallow depth, flat or gentle inclined surface, and smooth relief, which are more suitable for mining operation compared to the flanks of seamount."

Sep 1, 2014