Search Documents

By ERIK CHARRIER, HUGH MILLER, JOSEF BOURGEOIS

In this study, a unique excavation system was characterized, utilizing waterjet technology as the primary tool for material removal during rehabilitation of reinforced concrete and shotcrete structural liners. Through empiric testing, this research seeks to validate the hypothesis that waterjet removal of these support systems will result in less unintended damage than conventional removal methods. The intent is to develop a viable technology that will reduce the collateral damage caused to surrounding liners during excavation, improve the adhesion between shotcrete and the substrate for longer lasting ground support, and improve overall safety for workers in underground environments. An analysis on the fracture mechanisms and operating parameters of each method was completed. Instrumented shotcrete panels were physically tested and examined through visual inspection and ground penetrating radar (GPR) to compare substrate damage according to each testing method. After testing was completed, the data strongly indicates that waterjet cutting causes less collateral damage to the surrounding intact liner and substrate when compared to that of conventional impact hammers. This research is intended to provide a scientific basis for additional applied research in the rapid excavation and repair of shotcrete support systems.

Sep 23, 2021

Almost all of the world?s zirconium is mined in the form of zircon (ZrSiO4), the majority as a coproduct of titanium mining from heavy mineral sands deposits. These are placer type deposits, in which the dominant mineral is silica but which also contain a suite of ?valuable minerals,? often consisting of a mixture of titanium minerals, various alumino-silicates and zircon plus a range of other mineral species. The composition of the valuable minerals in such deposits is known as the mineral assemblage. There is no reasonable consistent geological relationship between zircon and titanium minerals. They can derive from separate igneous rock deposits that rarely occur together. The connection emanates once these separate rocks have been eroded by weather and water, often across a very long geological period. Once this has happened, zircon and titanium minerals often find their way to the same locations because they share two major characteristics:

Jan 1, 2011

By Andrew P. Gize

The analytical approaches used to solve a specific problem are dependent upon the information required, coupled with limitations imposed by available facilities, costs, and time. The organic matter associated with ore deposits has the potential to yield information for two problems. Information can be obtained to provide guidelines for prospecting, and, secondly, to solve genetic problems. A major potential of organic matter in providing prospecting guides lies in the high thermal sensitivity of organic matter in sediments which are metamorphosed at grades lower than greenschist facies. The organic matter can then be used to map thermal anomalies potentially associated with mineralization. The analytical approach is to determine the thermal maturity of the total organic matter, or of specific fractions, using techniques which are relatively quick and inexpensive. Consideration of genetic models (for example, reduction, complexing, involvement of oil field brines) generally requires more specific information than the overall thermal maturity of the organic matter, necessitating infor¬mation on molecular composition and structure. The facilities, time, and cost of this information are greater than for mapping thermal anomalies. The analytical techniques discussed include elemental analyses, spectroscopy (infra-red, visible and ultra-violet), Fourier Transform infra-red, nuclear magnetic resonance, extraction, pyrolysis techniques, chromatography and mass spectrometry.

Jan 1, 2013

By Ehsan Moradabadi, Debra F. Laefer

"To more rigorously address tunneling risks to above-ground structures, vulnerability evaluation of all structures along a tunnel route is required. This multi-block area along the route can be considered a district. To fully assess each structure within a tunnel’s zone of influence, a multi-block or district-level model may provide new insights as to risk evaluation and mitigation strategies. However populating such a model with the existing geometry of the built environment poses a major challenge as measured drawings are not readily available for all structures along a tunnel’s route. Cost-effective population of such a model could arguably involve remote sensing data in the form of laser scanning or photogramme-try. However even for unreinforced masonry structures, where external, above-ground geometries can be captured, without a prohibitively expensive building-by-building, in person survey many factors would remain unknown. To consider these uncertainties in an automatic way, a performance assess-ment framework is proposed. Such a framework allows a more rigorous, initial, risk quantification than is currently possible within the simple empirical models generally being used in industry when tunneling risk is initially assessed. This paper introduces (within the allowable space limits of this format) consider-ations for auto-population and application of a district-level, tunnel-risk screening tool. INTRODUCTION Challenging topography, intense urbanization and infrastructure development, combined with limited land availability and a growing awareness of environmental issues have lead to increasing usage of un-derground spaces to control aboveground traffic and provide essential services in metropolitan areas. Tunneling, however, is not without its own risks, especially with respect to aboveground structures whether it be widespread minor damage (Burland et al. 2001) or the more notable, although less fre-quent, large-scale collapses such as the 2003 Shanghai (Allianz 2015) or 2004 Singapore (Magnus et al. 2005) events."

Jan 1, 2016

By C. Clark, J. Seymour, D. Benton

"National Institute for Occupational Safety and Health NIOSH is conducting research on jackleg use and related accidents in underground metal mines. This paper provides an analysis and overview of jackleg drill usage, accidents, operational characteristics, and alternatives, based on information from injury reports, legacy research, stakeholder input, and published literature. Jackleg drills are involved in more ground fall accidents in underground metal mines than any other drill. Jackleg-related injuries are most prevalent at the face in the course of installing initial ground support. Alternatives to jacklegs for drilling and bolting under incomplete support in narrow underground openings are not yet available. Small mechanized bolting equipment needs to be developed to address jackleg-related accidents and improve safety at mines where jacklegs are being used. JACKLEG DRILL Description The term “jackleg drill” is a generic name for a class of handheld, rotary, percussion rock drills that are equipped with an attached reaction leg to provide stability and thrust for the drill (Figure 1). All of the drill and leg controls are located near the operator’s handle at the rear of the head portion of the drill. Jacklegs are classified according to the bore size of their pneumatic pistons which normally range from 6.03 to 8.26 cm (2.375 to 3.25 in) [Kurt, 1982; Clark, 2012]. Jacklegs typically weigh 460 N (103 lbs), but their weight can approach 535 N (120 lbs) after they are fitted for operation with drill steel and air and water hoses [McKibbin and Clark, 2001]. In underground mines, jackleg drills are commonly used to drill 3.8-cm (1.5-in) diameter holes 1.83 m (6 ft) deep in rock. Application The jackleg drill is primarily used in underground mines when the size of the ore body, the ground conditions, or the mining method do not permit large openings to be mined using mechanized equipment (e.g., narrow vein mining). Jacklegs are used to drill blast-holes for explosives and also holes for installing ground support. These versatile drills are used in nearly all phases of mining including exploration, development, production, and maintenance [Kurt, 1982; Williams et al., 2007; Chen and McKinnon, 2012]. The jackleg is used to drill holes in rock using drill bits attached to hollow steel bars called drill steels (rotary percussion drilling). After the hole is drilled, the jackleg can be used to install different types of ground support components, depending on the ground conditions and the specific ground support measures that are needed. For example, the jackleg can be used to install expansion-anchor rockbolts or resin-grouted rockbolts using the drill’s rotary-motion feature. On the other hand, the jackleg can also be used to install friction-type Split-Set™ rockbolts using the drill’s percussion (hammer-motion) feature. As shown in Figure 1, various washer-like bearing plates can be installed along with these bolts to provide additional ground support and to help secure surface control products, such as wire mesh and shotcrete that are in turn used to retain small, loose material between the bolts [Clark, 2012]."

Jan 1, 2016

By Erwan Yap, Brian Mangogna, Craig Romrell, Jeff McKay, Weishi Mang, Andrea Deml, Adam Steimel, Justin Dix

The Doe Run Company (Doe Run), a global supplier of lead (Pb), copper (Cu) and zinc (Zn) concentrates, and lead metal alloys, installed an enterprise expert control system— termed as Digital One—on the company’s Pb, Cu and Zn circuits at its Buick Mill in December 2022. Digital One was developed with Metso and deploys Metso’s product, VisioFroth™. This automated system is now running and optimizing the flotation processes for all three circuits (Pb, Zn and Cu), all plant air and methyl isobutyl carbinol (MIBC). In addition, Digital One also controls a second, newly built, modern flotation reagent system. Digital One also paves the way for automation and expert control of the entire mill, integrating grinding, thickening and filtration. Digital One is digitally immersed in a universal distributed control system (DCS); therefore, today’s mineral processing plants may be upgraded to it or designed around it. This presentation will explore the plant design and operation of this technology at the Doe Run Buick Mill.

Feb 1, 2024

By B. Boutilier, R. Mendoza

"First Majestic Silver Corp. (FMS) is a silver mining company founded in 2002 that operates exclusively in Mexico. It has six producing silver mines, one of which is the La Encantada silver mine (La Encantada) located in the state Coahuila. La Encantada is located near the southern United States border and 708 km (440 miles) north of the city Torreon.La Encantada is located in the Sierra Madre Oriental and is a high-temperature carbonate replacement deposit. Mineralization in La Encantada occurs in many different forms such as veins, chimneys, breccia pipes and reefs (mantos). Mineralization is mainly oxides of iron, zinc, lead and manganese, with high concentrations of sulfides at depth relating to two main intrusive events: the Milagros Intrusive and the La Prieta Skarn.Mining began in La Encantada during the 1950s with small vertical shafts, drifts and raises. It focuses on the high-grade silver zones using traditional hoists and extraction methods, before branching into two main separate mining camps: El Plomo and Penoles camp. Penoles, the previous owner, focused mainly on large ore bodies using post pillar cut-and-fill mining method to extract the higher-grade material. Due to the type of ground, irregularity of pillars, and rock conditions, large amounts of high-grade pillars had to be left in situ to ensure the stability of the excavations. The mined-out areas would then be filled with lower-grade material to assist in the stability of the secondary level. These room-and-pillar development entries were 2.5 m x 2.5 m (8.2 ft x 8.2 ft) and spaced every 10 m (32 ft), leaving a vertical pillar of 7.5 m (25 ft). First Majestic acquired La Encantada in 2006. After the acquisition of the mine, the company began the conversion of the surveying reference system from a local grid (Maria Isabel Shaft as 0,0) to the Nav27 coordinate system, and subsequently converted to the WGS84 coordinate system in 2015. Due to the extensive history of the mine, different areas were surveyed with different systems, causing significant challenges when designing the principal extraction levels, pillar heights and ramp locations. To overcome this difficulty, the entire mine was resurveyed and the old workings transposed to the new coordinate system, except for some inaccessible areas due to poor ground conditions or ground collapses. To further ensure pillar height and the safety of the mine workers, probe holes were drilled during the development process."

Sep 1, 2019

By George Saratsis, George Exadaktylos

In the marbel industry, ore reserves refer to the produced tonnage of orthogonal prismatic, defect-free blocks of commercial sizes and of marketable aesthetical quality. On the contrary, in the mining sector, ore reserves refer to the tonnage of ore with grade above some cut-off value. While in the mining sector ore reserves are reported according to existing standard guidelines, the marble industry has no standardmethod. The purpose of this paper is to present a method to estimate white marble reserves using drill coring or borehole wall logging and limited joint mapping on exposed marble surfaces. Data pertaining to fracture orientation, fracture frequency, size, and whiteness were collected. The primary phase of marble characterization is followed by the discretization of the orebody into a three-dimensional array of orthogonal prismatic blocks, where the marble whiteness and fracture intensity are attribute values. Both these variables are considered to obey continuous and not discrete probability distributions. The discretization is performed using computer aided design and the Block Kriging techniques. An outline to improve the description of a given marble ore deposit at the exploration stage is presented for the prediction of marble block size distribution from joint count measurements along diamond drill cores. An example case of a white dolomitic marble quarry is used to demonstrate these methods.

May 27, 2020

By Thomas J. Regan

The first stage of the Massachusetts Bay Transportation Authority's Red Line Extension Northwest, is a two-track rapid transit extension from Harvard Square in Cambridge, through three stations, to the Alewife Station/Garage complex in North Cambridge. The extension, about 5.0 km. (3.1 miles) in length, is entirely in tunnel, with the Alewife Station/Garage complex and adjacent line sections of tunnel constructed by cut-and-cover methods. The Station/Garage complex, just west of Alewife Brook Parkway, is in an area underlain by deep deposits of very soft highly sensitive clays. It is proposed to construct the station and adjacent tunnel sections by the slurry trench method, using the slurry wall as the permanent structural wall of the station and tunnel. The unusual nature of the underlying clay and its very high sensitivity raised questions concerning the feasibility of the proposed construction. Since research failed to reveal any construction precedent for the specific conditions encountered, a test section was undertaken to determine construction problems, resolve uncertainties, and to establish acceptable parameters for the construction of the slurry walls. PROJECT ORGANIZATION Sverdrup & Parcel as tunnel and transit systems consultant for the Red Line Extension-Davis Square to Alewife had overall responsibility for determining program objectives, project management and test implementation.

Jan 1, 1979

By Paul Madsen, Bade Sozer, Thomas Hennings, Eileen Test

The Rondout Bypass Tunnel in New York has two access shafts. The upper sections of the shafts are lined with steel pipe to resist a substantial net internal water head . Initial design included a ¾-inch-thick cement mortar lining (CML) for all three components. Because of concerns with CML application on large-diameter pipes, the protective lining was redesigned for shotcrete application. This paper discusses the details of that design, mock-ups, and shotcrete application.

Jun 13, 2023

By F. K. Spragins

The growing demand and a diminishing supply of conventional crude oil in North America are bringing about an ever increasing interest in the so-called "synthetic fuels". With one commercial plant already in full production, another in the planning and engineering stage, and still others being seriously considered, the Athabasca tar sands is proving to be a leading center of interest. Here, and in the closely related deposits, reserves in place total over 700 billion barrels.1 This major source of new oil is about ready to play a significant role in the filling of ever increasing market demand. When and if fully developed, the Athabasca tat sands could make both Canada and the United States substantially independent of all off-shore supplies of crude for many years to come. Its product, a high-quality, low-sulphur synthetic crude, is beginning to enter the market place at a most favourable time.

Jan 1, 1972

By W. M. Ma, Daniel W. H. Su, K. Centofanti, Yi Luo, W. L. Zhong, Syd S. Peng

5.1 INTRODUCTION There are several types of surface ground disturbances, each of which is immediately transmitted to surface structures and causes damage of various forms, depending on the location of the structures in the subsidence basin. Many criteria have also been proposed for defining the potential structural damage. All of these topics will be discussed in this chapter. 5.2 TYPES OF GROUND DAMAGES There are two types of ground damage, continuous and dis¬continuous, that could inflict damages to surface structures. Dis¬continuous ground damage is open fractures of various degrees. Four types of fractures are commonly seen (Brauner, 1973b): 1. Fissures or cracks. Cracks are the most common form of ground damage and range from completely closed to several feet wide. Surface cracks are most prominent when the ratio of mining depth to mining height is smaller than 30 to 50 times mining height. Cracks initiate parallel to, but ahead of the moving long¬wall face at some intervals when the depth-to-mining height ratio is less than 25 to 30. As the face continues to move, they open up and then close gradually, and in most cases eventually close up completely when the face moves farther away. Sometimes when the depth-to-mining height ratio is larger, cracks may initiate be¬hind the face and go through the same cycle. Cracks are also more likely to occur in the hill when the face is moving in the uphill direction. Cracks also occur at or near both sides of the panel edges. Those cracks tend to remain open permanently. When the surface is covered with grass or other vegetation, cracks of less than 1 to 2 in. wide usually do not penetrate it and become invisible on the surface. 2. Steps. A step may occur when the longwall face stops abruptly if the mining depth-to-mining height ratio is less than 20. Steps may also occur along the panel edges. Steps also range from a few inches to a few feet in width and depth. If planes of weakness are oriented favorably, ground will slide along these planes and form steps on the surface. 3. Cave-in pits. These result from local collapse of the ground from the mine level to the surface when the mining depth is less than 150 ft and occur mostly above abandoned mined lands. They may be as large as 40 ft wide and deep. 4. Bumps (compression ridges). Bumps result from ground compression and occur mostly near panel center some time after mining. Bumps of up to 4 ft, but mostly 1 to 2 ft, have been identified. Continuous ground damage refers to the formation of the sub¬sidence basin where continuous nondestructive ground deforma¬tions occur. As mentioned earlier, continuous ground deforma¬tions associated with a subsidence basin include subsidence, slope, curvature, displacement, horizontal strain, twisting, and shearing. 5.3 TYPES OF SURFACE STRUCTURAL DAMAGES Both continuous and discontinuous ground disturbance cause damage to surface structures. A. Structural Damages Due to Discontinuous Ground Disturbance 1. Fissures or cracks. Open cracks can cause dislocation of surface structure if the gaps are sufficiently large so that the struc¬tural elements cannot resist but fail. On the other hand, minor cracks affect only the appearance, and not the structural integrity. 2. Steps. When a surface structure is located on a step, some portions of the structure lose support and become overhung. In the case of a residential house, there will likely be many open frac¬tures in the overhung portions, followed in severe cases by sepa¬ration of the superstructure at the edge of the step. 3. Cave-in pits. If the caved-in pit is larger than the surface structure, the structure will drop into the pit and become unstable. If the caved-in pit is smaller than the surface structure, the struc¬ture may either become overhung or lose support in some portions. In either case, it is unsafe for use. 4. Bumps (compression ridges). Bumps will disrupt roadways or house floor. If located under supporting members of the struc¬tures, it may cause damages. B. Structural Damage Due to Continuous Ground Disturbances 1. Subsidence. Pure subsidence or uniform subsidence over an area does not cause any structural damage. However, if it becomes a topographical low area, it may be flooded with water and make the surface structures unusable. It must be noted that the flat bottom area at the center of the final supercritical subsidence basin does not reach that position suddenly. Rather, as shown in Fig. 3.1, it is subjected to the dynamic surface deformation asso¬ciated with the traveling subsidence basin before it is left behind to be part of the flat-bottom area. Therefore any structure located at the center of the final supercritical subsidence basin must be able to resist the dynamic surface deformation in order not to be dam¬aged. 2. Slope. Ground slope will induce tilting of the structure. Tall structures with small base areas, such as water towers, chimneys, and power transmission towers are most sensitive to ground slope. If the ground slope is such that if after tilting the center of the gravity of the tilted structure falls outside the base area, it will topple, but this seldom occurs. Ground slope will change the designed slope of a buried trans¬portation pipeline, either increasing or decreasing the original slope depending on whether the ground slope coincides with or opposes the original slope. There are maximum allowable final slopes for various types of transporting materials. Ground slope also affects highways and railways. There is a maximum allowable final slope for a railway because tractive effort increases 1/1000 of its weight for every increase of 1/1000 in grade. 3. Curvature. There are positive (convex) and negative (con¬cave) curvatures. When a surface structure is located on a positive curvature, both ends become unsupported, followed by bending upward at the midportion. The top portion is subjected to more severe stretching than the lower one. As a result, vertical cracks with a wider gap at the top occur at the window, door frames, on the walls, and at -the wall joints. V-shaped cracks appear at the

Jan 1, 1992

By Zong‑yu Li, Shao‑jian Ma, Xiao‑jing Yang, Jin‑lin Yang, Xing‑nan Huo, Heng‑jun Li

Optimizing and adjusting the particle size composition of grinding products is of great significance for improving economic benefits and resource recovery and utilization. In this study, grinding contribution and quantitative separation of impact and grinding mechanism in cylindrical mill were creatively researched, and the grinding technical efficiency of impact and grinding was coupled to the grinding technical efficiency of grinding in drop-off mode. The results showed that the contribution rate of impact and grinding in grinding in drop-off mode varied with the grinding time. On the whole, the contribution rate of impact action increases with the grinding time and gradually becomes stable, and the contribution rate of grinding effect was just the opposite. Under the experimental conditions, the main contribution of the grinding process is impact action, and the contribution of grinding action is auxiliary. In addition, the contribution rate of impact and grinding effect in grinding in drop-off mode was also related to the feed particle size. The contribution rate of impact effect decreased with the decrease of feed particle size, while the contribution rate of grinding increased inversely.

Aug 3, 2023

By M. L. Harris, I. Zlochower, M. J. Sapko, I. E. Perera

Experiments conducted with limestone dusts and dolomitic marble dusts have indicated that when rock dust is wetted and subsequently dried, it becomes a solid, non-dispersible cake. However, in order to be effective, rock dust must be able to disperse as individual particles to inert. To counteract this, rock dust manufacturers created treated rock dusts that will resist caking after moisture exposure. National Institute for Occupational Safety and Health (NIOSH) researchers conducted a series of laboratory-scale experiments on four base rock dusts and their treated counterparts to assess the effectiveness of various anti-caking additives after being exposed to moisture and then dried. The dusts were exposed to moisture using humidity cabinets having a high relative humidity (99% RH) and by also exposing the rock dust bed to water through bottom wicking. The dusts were then evaluated for dispersibility after drying using the NIOSH-designed dust dispersion chamber. The anticaking additives were different concentrations of stearic acid, oleic acid, and xylene-based surfactants. All results were compared to a reference rock dust used to conduct large-scale experiments in the Lake Lynn Laboratory (LLL), Fairchance, PA. When the untreated dusts were dried after exposure to moisture for one day, no dispersion was measured. However, rock dusts treated with anti-caking agents were readily dispersible even after exposure to moisture for six months. This report details the analysis and characterization of anti-caking additives using the NIOSH-designed dispersion chamber and the 20-L explosion test chamber. INTRODUCTION In order for a coal dust explosion to propagate, five elements are required. In addition to the fire triangle in which three elements are necessary to sustain a fire—fuel (coal dust), heat (ignition source), and an oxidizer (oxygen in air)—a combustible dust explosion requires dispersion of a dust cloud (pressure wave) and confinement of a dust cloud (underground mine entry) (1). Coal dust explosions can originate anywhere in a mine. For example, when a small volume of a flammable methane and air mixture is ignited in a closed end, the high-temperature gases rapidly expand to create a pressure wave, sometimes referred to as a “pioneer wave,” that may steepen into a shock wave as it propagates away from the ignition source. The shock wave produces a wind that disperses the dust preferentially from any elevated and exposed surfaces (roof, ribs, belt structure, cribbing, etc.). Factors that are known to affect the intensity of an explosion are the dust particle size, the location of the dust within the entry, the dust dispersibility, and the volatility of the coal dust (1). Particles less than 75 μm (< 200 mesh) in size are most reactive (2). Dusts that are located on the roof, ribs, and elevated surfaces are more readily dispersed than dusts on the floor. Therefore, application of quality rock dust in sufficient quantities is essential to inert coal dust and to prevent continued flame propagation. 30 CFR 75.402 and 75.403 require 80% total incombustible content be maintained within 40 ft of the face, and 30 CFR 75.2 defines rock dust acceptable for use in underground coal mines. It also defined that “when rock dust is wetted and dried, will not form a cake”.

Jan 1, 2019

By William G. Pariseau

The flexure of geologic strata, a phenomenon of inter- est to geologists and mining engineers alike, is examined as a sheet bending problem&apos; in Coulomb plasticity. Formulae for the distribution of stress, strain and displacement increments, volume change, change in the length of the central surface and power of dissipation, as well as for the neutral surface shift are given. Strains of any magnitude are considered. The analysis shows that deeply buried strata may bend and develop "tensile" cracks under generally compressive states of stress. It is also shown that bed separation and high capacity props are desirable in mechanized longwall mining, a result in keeping with operating experience. Although speculative at this time, the analysis provides a rational working hypothesis as regards the problem of strata flexure and control.

Jan 1, 1968

By C. T. Holland

Coal mining has been an important industry in the Appalachian area for many years. This is particularly true in the northern part of the area, namely, in Pennsylvania, West Virginia, and Ohio. Also, in the south a great deal of mining activity has been carried on in Alabama, Kentucky, and southwest Virginia. Some of the by-products of this activity has been the production of mineralized water from the mines in copious quantitites. The southern Appalachians have been somewhat more fortunate in that the water there has had a considerable amount of alkalinity in it, which has to a large extent eliminated some of the more undesirable aspects of mine drainage. Northern Appalachia, including central and western Pennsylvania, the Monongahela basin in West Virginia, and the Appalachian area in eastern Ohio have not been so fortunate in that coals in those areas and the top and bottom rock have, in many cases, shown considerable quantities of pyrite, and the water does not carry the carbonates found farther south.

Jan 1, 1969

You have been involved with research activities in froth flotation and size reduction. What do you think the future holds for these technologies? Froth flotation and size reduction are essential processing steps common to almost all current mineral-processing operations. The most significant recent advances in both of these technologies have been in the increased size of equipment and in some alternative machine designs, such as the column cells and the high-pressure roller mills. I believe that the next major area of improvement in size reduction will be at least partially driven by an improved awareness of controlling the conditions that influence the efficiency of particle breakage. This would include factors such as water-chemistry influences, the influence of fines from classification, chemical grinding additives and better rheology control. In froth flotation, significant changes are currently taking place in the plant use of frothers. Also, there will be an increasing number of new collector chemistries for certain types of flotation, such as with oxide minerals, oxidized mineral recovery in sulfide systems and improved selectivity with certain sulfide mineral systems. You have been active in implementing new engineering technology in industry. What do you think will be the technological future of mineral processing? Being involved in the invention and industrial implementation of new technology has been one of the most positive experiences of my career. I also have had the unique experience of working in the chemical and petroleum industries as well as in mineral processing. In my opinion, the future of mineral processing will be an exciting, wonderful work area in which to be involved. The development of new technology in minerals processing offers a special challenge compared, for example, to that of chemistry or chemical engineering. In successful industrial innovation involving minerals, having a sound theory is not enough. Instead, what is required is a valid blend of a good idea, meaningful laboratory characterization and, most key, the experience necessary to adjust the plant in such a way to incorporate the idea. The complexity of engineering systems that contain solids, liquids and gases, as well as highly variable natural mineral properties, means that nothing new comes easily. In some cases, it has been difficult to explain how processes practiced in industry for decades actually work, in terms of physical and chemical fundamentals. On the other hand, when a new idea is successfully implemented, the economic and professional returns can be very rewarding. I know of no more challenging field of engineering than minerals processing. What is your view of the future of the minerals industry in general? The need for minerals, metals and coal will be with us for decades to come. In many aspects, the minerals industry became global much earlier than some of the other industrial sectors that are currently experiencing globalization. I believe that fair international competition is beneficial to the users of minerals, metals and coals and to those involved in producing such materials. The key word here for a global economy to work is "fair." So the various playing fields involved such as finance, profit return, regulation and labor should be relatively level for all the players involved. Competition is an amazing driving force for innovation. This has been true in the minerals industry during the last few decades. The mining industry is producing more at less cost per unit than ever before in our history. I anticipate that this trend will continue as long as the global political situation remains relatively stable.

Jan 1, 1997

By William A. Kneller

Fifteen samples of chert from seven localities in Ohio were tested for potential durability and reactivity in concrete. The tests determined are porosity, pore-size distribution, relative degree crystallinity, specific surface area, and degree of dissolution according to the ASTM C289-71, Potential Reactivity of Aggregates, Chemical Methods. The results of these tests were compared with petrographic, electron optical, physical-chemical, and engineering properties of the chert samples. Based on these tests, the important properties that affect the durability and reactivity of chert in concrete were observed to be: (1) porosity, (2) pore-size distribution or pore spectra, (3) relative degree of crystallinity, (4) grain size, (5) specific surface area, (6) impurities, and (7) amount and species of quartz present-all of which are functions of original composition, time (geologic age), depth of burial, tectonics, and diagenesis. Preliminary results of this study indicated that the geologic history and physical-chemical properties of chert vary from one sample to another, and any one or combination of these parameters affect the performance of the chert in concrete. These complex interrelationships are difficult to ascertain; if the performance of the chert in concrete is to be predicted, it is necessary to study in detail this enigmatic material.

Jan 1, 1978

By Ronald R. H. Cohen, Margaret W. Staub

Two pilot scale bioreactors designed to treat acid mine drainage primarily using sulfate reducing bacteria were constructed underground at the Eagle Mine Superfund site in Minturn Colorado. The project was designed to test th applicability of microbiological treatment on water with high metals concentration and to test the process in an underground environment. Objectives were, 1) to compare metal removal, pH increase, and sulfate reduction in a single stage reactor with a double stage reactor of equal volume at varying flow rates; 2) to determine where within the substrate treatment occurs· and 3) to examine volume versus surface ara as a design parameter for optimizing metal removal processes. Results from the reactors showed that the single stage reactor and double stage reactor performed equally well for the removal of Cd, Cu, Pb, Fe, Mn, and Zn. pH increased above 6.5 in both reactors. Greater than 97% of metals were removed within the first ten inches of substrate. Volume proved to be a more useful parameter for determining removal rates than area. Using volume as a design parameter rather than surface area enables PMDT systems to be constructed as packed columns rather than broad wetlands, Thus, space requirements are significantly reduced.

Jan 1, 1993

By A. ALLANORE, OLIVEIRA M. DE, D. CICERI, D. P. CHEN

The alkaline hydrothermal processing of K-feldspar rocks in an autoclave can be a pathway to synthesize a potassium fertilizer for tropical soils that is potentially cheaper and more efficient than traditional potash (KCl). When K-feldspar undergoes hydrothermal alteration in the presence of calcium oxide (CaO), it generates a complex mixture of calcium-aluminum-silicate-hydrate (CASH) minerals that incorporate K atoms stochastically in their structure. These atoms are subsequently released, as shown in a test-tube leaching test, indicating a possible uptake by crops. The relationship between the processing temperature and time in the autoclave for the hydrothermal reaction and the resulting mineralogy and elemental release are only partially understood and are investigated in this study. Elucidating that relationship is the key requisite for subsequent techno-economic analysis, and ultimately for the development of a fertilizer that can be considered as a feasible alternative to KCl.