Search Documents

By Yuting Xue, Danqing Gao, Brijes Mishra

Heterogeneity and discontinuity significantly affect rock strength. For accurate stability prediction, intact rock behavior is imperatively included in rock mass behavior. However, past research largely used arbitrary scaling approaches to produce rock strength. This paper considers a stochastic approach in order to determine the strength of a rock. Based on the laboratory data, a MATLAB® with extreme value stochastic model generates a database for each physico-mechanical property. Then FLAC® simulates laboratory-sized rock specimens. The grids developed in the numerical model can in turn develop random material properties in MATLAB®, which researchers then applied to the final FLAC® model. Model runs simulate the approach performed in the laboratory. The results from the model indicate that a stochastic approach produces strengths that are lower than a deterministic approach. Failure modes for each specimen are different, similar to observations in the laboratory. In addition, random density also influences the failure mode, highlighting the importance of stochastic analysis in rocks.

By Lewis J. Patterson

In the period of time allotted to this paper, an attempt will be made to cover a great deal of territory, figuratively speaking, as far as our experience with ammonium nitrate is concerned. In giving this subject the "broad-brush" treatment, it will be necessary to generalize on the major points which at the same time will permit me to avoid, to a great extent, any involvement in the purely technical and theoretical aspects of blasting. The practice of theorizing before a new idea is tried has practically been discontinued in our organization simply because experience has shown that, almost without exception, theories have fallen aside as some new development takes its place. In regard to blasting, logic and experience seem to have little place in this phase of quarry operations. As the use of low cost blasting agents was introduced in our operating practice, a man who had no previous experience in the field of blasting but with sound knowledge in safety procedures was given the responsibility of supervising the drilling and blasting operations. A total lack of experience is not ordinarily recommended as a prerequisite to assuming the responsibilities of a supervisory position. However, in this case it was obviously a wise decision because there were no pre-conceived ideas as to what techniques would or would not be successful.

Jan 1, 1958

By Michael E. Lively

DOUG HALBE: We've talked about copper operations and gold operations. For our third section on the topic "Operating Ideas That Have Saved Me Some Bucks," we'll turn to the coal fields. Our featured speaker is, I'm almost embarrassed to say, a mining engineer, Mike Lively. Mike has 25 years' experience in the coal industry. He is currently superintendent of surface operations for Southern Ohio Coal Company, Meigs Division (AEP Company). I've read his paper, and there's some really great information here. Mike.

Jan 1, 1998

By Brian Zelenko, William H. Hansmire

"By the time the latest expansion of the Washington Metropolitan Area Transit Authority (WMATA) system, known locally as Metro and which opened in 1976, is completed in 2020, the system will serve 97 stations and operate on 188 km (117 miles) of track on six interconnecting lines. Metro provides a critical transportation link to a population of approximately six million people within a 3,900-km2 (1,500-sq-mile) Washington Metropolitan area and has allowed job growth to expand to all corners of the region. In the 1950s and 1960s, when the system was first conceived and construction began, most jobs were centered in downtown Washington, and most of the workforce commuted by bus or car. Today, transit-oriented development has increased residential, commercial and government facilities near most of the existing 91 stations increasing the importance of the Metro system as a critical transportation link for the region. According to recent American Public Transportation Association (APTA) data, Metro is the second busiest transit system in the United States (after New York City’s transit system).During the nearly 50 years of construction on the Washington Metro system, technology improvements and lessons learned from the global tunneling industry were implemented. Portions of this background and history have been adapted from other work by the authors Roach et al. (2017) and expanded for use herein. For soil tunnels, these improvements included the change from a “two-pass” tunnel lining with a typical initial lining of steel ribs with wood lagging or segmental precast lining erected within the tunnel shield followed by a final lining of cast-in-place concrete to a one-pass lining system of pre-cast concrete gasketed segmental lining. Soil tunnels were originally excavated using open-face tunnel shields, but changed over time. By the late 1980s, tunneling using closed, pressurizedface tunnel boring machines (TBMs) using a one-pass tunnel lining consisting of segmental precast concrete permitted tunneling in a wider range of soil conditions with much less risk of damaging overlying utilities or structures, greater safety for tunnel construction personnel and without the need to dewater the soils. However, due to concerns about conditioning clays with earth pressure balance (EPB) TBMs, open face machines were still favored by contractors for their better advance rates, lower cost and ability to deal with boulders that were occasionally encountered in the Coastal Plain Terrace Deposits."

Jan 6, 2018

By Feng Dingwu, Chen Jin, Sun Zhongyuan, Peng Shiying

The recent development of rare-earth permanent magnets has impacted the field of magnetic separation. The permanent magnets technology led to the advent of various magnetic separators particularly designed for application in mineral processing. In this paper, a new type of rare-earth PHGMS possessing a higher magnetic field strength in the working zone was developed using finite element analysis techniques. The NdFeB permanent magnets used had properties of 38 MGOe stored energy, and magnetic material flux levels exceed 1.2 T, The combination of scientific and engineering design and suitable matrices can offer an effective separation of industrial minerals, such as kaolin, feldspar, etc. Compared with conventional high intensity electromagnetic separators, the equipment can reduce electrical energy over 80% with lower operation and maintenance costs, and less installation space.

Jan 1, 1995

By Clayton Williams, Dale M. Hata, Glenn M. Boyce

The Upper Llagas Creek Flood Protection Project in Northern California encompasses portions of the communities of Morgan Hill and Gilroy, and unincorporated areas of Santa Clara County. The project provides for flood protection improvements along Llagas Creek and two of its tributaries, West Little Llagas Creek and East Little Llagas Creek. Llagas Creek is one of the tributaries of the Pajaro River and drains a watershed of approximately 104 square miles. The river system has a history of flooding the watershed communities, and the project’s goal is to provide 100-year flood protection by creating a bypass infrastructure, including channels, cut-and-cover culverts, and a tunnel. The project has been divided into several phases. This paper describes Phase 2A, which consists of approximately 2,150 linear feet of lined horseshoe-shaped bypass tunnel measuring 14 feet wide by 12 feet high. The bypass tunnel was sequentially excavated using a combination of roadheader and controlled blasting through colluvium and weathered to fresh greenstone. The tunnel was mined near residences, requiring strict noise and vibration controls. Phase 2A also includes the construction of twin bypass concrete culverts, portal shoring, and dewatering systems. It features the use of a Design Review Board and partnering for project delivery. This case study discusses the bypass tunnel design, progress of tunnel construction, plans to complete the work, construction risks, and the software and procedural tools being used to manage the project, including ProjectWise construction management software.

Jun 13, 2023

By A. J. S. Spearing, B. Forbes, T. Kostecki, A. Hyett

Improving upon the past understanding of the interaction between installed rock bolts, the immediate roof and sidewalls is vital for the implementation of sound support system design, as this has a direct impact on rock-related safety. This is the primary goal in rock-bolt-related research. The earliest research in this field concentrated on limited laboratory and in situ measurements accompanied by theoretical analyses, based on the Kirsch equations. This represented the initial insight into understanding relative ground movements and their impact on primary support. However, these studies were far from complete. More recently, major technological advances in computing power within the mining industry has changed the scope from theoretical analysis to computer simulation. Even with these advancements our understanding of rock bolts in situ and in the laboratory has not progressed, particularly concerning bending and shear. To measure the behavior of rock bolts, the widely accepted practice is to populate the bolts with an array of strain gauges. Historically, resistive foil strain gauges or long displacement sensors have been used. Additionally, all instrumented rock bolts have used only two diametrically opposed slots. Rock bolts instrumented with these methods have significant shortcomings, one of which is the inability to capture shear and bending. The shearing and bending of rock bolts are particularly common in tabular soft rock mining, such as coal mining. This paper discusses the use of three slotted rock bolts, cut diametrically 120º apart, and two new optical fiber technologies populated along the entire rock-bolt length.

Jan 1, 2015

By L. C. de Kooker, K. Esmaeili, I. Musonda, M. Ferentinou

A numerical investigation of the effect of pore pressure regime on the safety factor and the critical failure mechanism is presented for fly ash storage facility. Pore pressures’ measurements from standpipe piezometers and pore pressure estimated from seepage analysis are used to compare the factor of safety for a fly ash slope. This was applied for considering static and seismic scenarios. A probabilistic approach was applied to account for the uncertainties resulting from the limited data available and support a qualitative risk assessment evaluation. Slope stability analysis is conducted in two and three dimensions, adopting the limit equilibrium analysis approach, and also a finite element seepage analysis, to assess the stability of the slope. The two-dimensional cross-sections were extruded to three-dimensional models to estimate the factor of safety and associated shear failure. The results from the performed analysis suggest an increase in safety factor values of 5%.

Mar 27, 2024

By Dewa Putu Agus Sudarmaja, Widi Astuti, Januarti Jaya Eka Putri, Yayat Iman Supriyatna, Himawan Tri Bayu Murti Petrus, Siti Nurul Aisyiyah Jenie, Ferian Anggara, Anisa Maulidia, Vincent Sutresno Hadi Sujoto, Sutijan, Wayan Warmada

With the rapid development of renewable energy technology, such as electricity reserves to store energy for electric and battery-electric vehicles, environmentally friendly energy sources are expected to continue to be tapped to meet mobility and stationary energy needs. Lithium is the most attractive candidate for energy storage development. The presence of lithium in the Sidoarjo mud in Indonesia makes it interesting for use as an alternative source of raw material. In this research work, sulfuric acid was used as a solvent, and hydrogen peroxide as an oxidation agent. Lithium recovery was studied with a leaching process at various temperatures (30, 45 and 60 °C) and sulfuric acid concentrations (0.5, 1, 2, 3, 4 and 6 mol/L). Increases in temperature, sulfuric acid concentration and hydrogen peroxide concentration were found to directly affect the lithium recovery. An increase in sulfuric acid concentration is directly proportional to the recovery of lithium in the solution. Optimum conditions were obtained at a sulfuric acid concentration of 6 mol/L and temperature of 60 °C. The shrinking core model was used to study leaching kinetics, and ash layer diffusion acted as a rate-controlling process. The activation energy of the leaching process was found to be 38.90 kJ/mol.

Jun 1, 2024

By Jeremy Maurer, Duah Philip, Awuah-Offei Kwame, Donya Otarod

Land use impact assessment for mining is time- consuming and expensive. Because of mining’s impact on biodiversity, land use assessment methods that evaluate biodiversity are important for mining land use impact assessments. Remote sensing, in particular satellite multispectral sensing platforms such as Sentinel‑2 and the Landsat mission series, have been used to assess and quantify biodiversity through proxy variables such as NDVI (Peña-Lara et al., 2022). The objective of this paper is to present results of a comparative study of land use and biodiversity based on multispectral satellite observations and production data from copper and cobalt mining in the Democratic Republic of Congo. We quantify the relationship between different spectral bands and vegetative indices and the production data provided by the mining companies and measure correlations. The results suggest that remote sensing could be a cost- effective means of assessing biodiversity impacts of mining.

Feb 1, 2025

By Timothy Batchler, Khaled Mohamed

Standing supports have been used in coal mines for decades to enhance roof support capability. Sometimes standing supports are used as a tool to resist the lateral movement of spalled ribs. Researchers from the National Institute for Occupational Safety and Health (NIOSH) are conducting a testing program for different types of standing supports (steel and timber) to investigate the effect of lateral loading on their vertical loading capacities and the factors affecting their lateral loading capacities. In this paper, the mine roof simulator (MRS), at the NIOSH Pittsburgh research facility, was used to determine the response of steel props to vertical and horizontal loadings. Finite element models (FEMs) were developed and verified using the tested steel props. To justify the testing program for testing standing supports with end-conditions of rock-like materials, the verified prop models were used to study the effect of a wide range of roof and floor materials (gray shale, shale, and claystone) on the critical buckling loads of the steel props. Also, several lateral loading scenarios were evaluated in which the steel props were laterally loaded at different heights. The critical buckling load for steel props setting up against a claystone roof and floor was found to be one-half of that shown by the MRS test where roof and floor platens are made of steel. Minimum prop performance was observed when the lateral load was applied at the mid-height of the steel prop, especially at small lateral displacement (less than 2 in).

Sep 10, 2022

By Sai Phaninder Reddy Chaganti, Corrina D. Beaven

This study investigates the effect of reagent type, dosage, and pH on flotation kinetics and copper recovery for secondary sulfide ore with elevated clay content. The primary objective was to determine whether Xanthate performs comparably to or better than the currently used primary collector, Thiophosphate. Approximately 80 kg of ore was collected from three blast holes and systematically prepared through drying, crushing, grinding, and flotation testing. Grinding tests were conducted to establish optimal grinding time and lime consumption for pH control, achieving a target particle size distribution in 13 minutes and 30 seconds. Elemental and mineralogical analyses using X-ray Fluorescence (XRF) and X-ray Diffraction (XRD) identified a copper content of 0.36% and significant clay presence, affecting flotation performance. Fifteen flotation tests were performed under controlled conditions, with variations in reagent dosages. Control tests confirmed reproducibility, with recoveries around 80–82%. Increasing the pH did not improve kinetics or recovery, making higher pH adjustments economically unjustifiable. Adjusting the Thiophosphate dosage yielded the best recovery of 83%. Xanthate collectors, tested both as tertiary additives and as replacements for Thiophosphate, delivered comparable or superior recoveries—up to 91.5% in plant tests—and demonstrated faster flotation kinetics, even under high-clay conditions. These findings highlight Xanthate’s reduced sensitivity to clay, potential for lower dosage requirements, and operational benefits such as improved selectivity and circuit efficiency, validating its role as a cost-effective and alternative for processing complex sulfide ores.

Feb 22, 2026

By F. M. Benavides

The mining complex being analyzed consists of four mines and two processing plants located in an area where there are several existing modes of transportation. Figure 1 shows a map of the general layout of the four proposed mines and the two existing processing plants. The mines are identified by the numerals "I" through "IV" and the plants by the letters "A" and "B". A proposed overland conveyor would collect the product from all four mines and convey it to Processing Plant A. Alternate transportation systems are as follows: Railroad transport from Mines I and II to Plant B; Highway trucking from Mines I and II to Plant A; Off-the-road truck haulage from Mine III to Plant B and from Mine IV to Plant A. River transportation from the mines to the processing plants was not considered in this study under the assumption that the high capital investments for the loading and unloading facilities, in addition to difficult traffic problems, would make this mode of transportation unattractive.

Jan 1, 1980

By David Newman

"Horizontal stress can have a profound effect on the stability of an underground limestone mine. The presence of horizontal stress is usually determined once the mine has been developed and the orientation of headers and crosscuts are well established. Multiple attempts are typically made to control roof falls without re-orienting the mine. Once the decision has been made to change the orientation, pillar centers, mine opening widths, and the question of how to determine the correct orientation must be answered.A case history is presented to illustrate how geologic structure, ground conditions and roof falls in adjacent mines, the World Stress Map (Heidbach et al., 2016), in-mine measurement of “cutter” roof orientation, the orientation of strata offset (cats eyes) within borescope holes, and the diametral deviation method of determining horizontal strain from drill core were used to establish the most likely range of horizontal stress.The main headers were re-orientated in a direction parallel to the median of the range of horizontal stress. The crosscuts were angled 60° to the headers to avoid being perpendicular to the horizontal stress direction. Pillar centers and opening widths were increased in the favorable stress direction of the mains and decreased in the less favorable crosscut orientation. The major principal horizontal stress magnitude was estimated using the strain measurements from the diametral deviation method and elastic modulus obtained through testing.INTRODUCTIONOver the past decade, there has been a significant increase in the number of underground stone mining operations in the United States. As stripping ratios at surface quarries become uneconomical and reach the extent of the mineral boundary, coupled with the encroachment of urban development on previously rural mining operations, the remaining mine reserves are best accessed through underground development.Although the majority of underground limestone mines in the Midwest are in relatively flat lying deposits with minimal geologic structure, many Appalachian mines are in folded and faulted environments. Tectonic horizontal stresses associated with multiple orogenic episodes are locked in the formation and are released as the underground mine is developed.A common misconception is that horizontal stress impacts are more prevalent at shallow depths where the ratio of horizontal to vertical stress may be high. However, field observations and academic research indicates that horizontal stress conditions may be encountered at any depth due to the tectonic compression of the limestone formation (Esterhuizen et al., 2007; Dolinar and Esterhuizen, 2007; Iannacchione et al., 2003; Slaker, Murphy, and Miller, 2017; Kuhnhein and Ramer, 2004). This paper outlines mine design and layout guidelines for the mitigation of horizontal stress impacts on underground stone mining operations through a case history example. This approach to mine planning and the ability to anticipate horizontal stress can significantly improve future production of multiple levels (Newman and Newman, 2019). As underground stone production continues at deeper depths and in more geologically and geometrically complex mining conditions, an emphasis on ground control and the anticipation of horizontal stress can provide safer and more productive single and multiple level mining operations."

Jan 1, 2019

By G. A. Gunderson

Since our time is very limited, I would like to relate to you as best as I can a few important areas that I think may be helpful. 1.) The Real Difference between Dense Phase and Dilute Phase Pneumatic Conveying: Within the many variations of so called Dense Phase conveying, it is often difficult to determine to what degree a system is Dense Phase or if, in fact, it is a Dense Phase system at all. A system that appears and is generally known to be Dense Phase can under certain operating conditions perform as a Dilute Phase system. If, for instance, a high pressure system, which is generally a Dense Phase system, operates at 60 PSIG, say 4 atmospheres, utilizes enough air volume, the conveying velocity will easily exceed the normal design velocity of a typical Dilute Phase system. Now, on the other hand, a low pressure system which we will term a Dilute Phase system, operating at 15 PSIG; say 1 atmosphere, can convey a given product at well below the saltation velocity, like a Dense Phase system.

Jan 1, 1977

By Robert L. Major

The expanded role which coal has been assigned in the energy future of the United States has raised numerous policy questions. The very complexity of these questions makes them suitable to analysis by econometric models. However, as the Wall Street Journal indicated in its recent article, business' success with such models have been mixed. I have been asked to present my views as to how coal producers can use such models and in what ways the industry is likely to be impacted by such models. I do not presume to speak for the whole coal industry, but only to share with you the personal observations of one who has worked "both sides of the street", having been employed' both by government and a consulting firm prior to joining the coal industry. In my opinion, the use of econometric models to analyze the coal industry will impact the coal producers in two main ways. First, their use by government will have a profound impact on future government policies related to the mining, transportation and utilization of coal. Second, such models, when properly calibrated and refined, may become useful tools for the coal producers in doing market research and long-range planning. While the former has already begun to impact on the operating environment or the coal industry, the latter is still in the embryo stage.

Jan 1, 1977

By W. Jacobi, B. Haider, D. Regulla, J. Huber

[Introductory Remarks] Thermoluminescence (TL) detectors are widely used for the dosimetry of X- and[ y]-rays. Also filter devices for radon daughter monitoring have been developed in which the a activity on the filter was measured with TL-detectors (Breslin et al., 1977). For this purpose normal LiF-tablets with a thickness of 0.4 - 1 mm were used. However the lower detection limit of such TLmonitors for radon daughters is relative high, especially in areas with a high [y]-background, due to the low [a /-y]-sensitivity ratio of such thick LiF-detectors. This [a/y]-sensitivity ratio can be increased if TL-detectors are used whose thickness is comparable with the range of [a]-particles. On the basis of this consideration we have developed a simple light weighted and sensitive TL-monitor for the measurement of the cumulative radon daughter exposure in air. [Description of the "Monitor] The monitor consists of two parts: The sampling pump with the accumulator, and the sampling probe which contains the air filter and TL-detector system. Both parts are connected with a plastic tube. For operation in mines a light weight, portable air sampler with a built-in accumulator (DuPont model 125 and 200, 400 g) is used which enables an adjustable, constant flow rate in the range of 7.5 -12 1/h. These air samplers allow a sampling period of 10 hours before recharging is necessary. For radon daughter measurements in houses this pump is replaced by a larger, netoperated pump with a flow rate of 180 1/h. Figure 1 shows a schematic cross section through the sampling probe whose weight is 40 g. The radon daughters are collected on a hydrophob membrane filter (Sartorius) with an effective filter diameter of 11 mm and a pore diameter of 3 µm; its collection efficiency for radon daughters is [>] 95%. Above the filter the detector system is mounted. It consists of two thin Tm-activated CaSO4-TL films of 8 mm diameter on a Al-carrier foil manufactured by Matsushita Inc., Japan. The thickness of the TL-film is 6 mg/cm2, which is comparable with the range of a rays. The first detector is faced in 3.5 mm distance above the filter; in addition to the ambient y background this detector is exposed to the [a] and ß radiation from the radon daughters on the filter. Between the first and the second TL-detector is an Al-absorber of 0.5 mm thickness which shields this detector against the [a] radiation and partly also to the ß radiation from the filter. Both detectors have the same [y] shielding. After air sampling both TL-detectors are read-out with a commercial, hot-air reader (Matsushita Inc. / Japan, Model 505 A). The glow-curves are identical for [a and y] rays (Regulla et al., 1980). The integral TLsignal from both detectors is displayed in mR-units (or mR-equivalent). The difference between the response of the unshielded TL-detector above the filter and the shielded TL-detector is proportional to the time-integral of the filter activity, integrated over the sampling period. Calibration and Intercomparison Measurements] The linearity of the a response was checked with a 241Am-source for an [a] fluence on the detector surface of 5400 [a's/cm2•s] in the range of 102 -105 mR-equivalent. Within the experimental error of 15% the response function is linear. The TLD-monitor was calibrated for radon daughters in air by comparison with a calibrated integrating, monitor (WLM-meter) equipped with a Si-surface barrier detector and a direct electronic read-out; this instrument was developed by us for area monitoring some years ago (Haider et al., 1976). The results of simultaneous measurements with the TL-monitor and the electronic WLM-meter in mine areas and in indoor air of houses are shown in figure 2. On the abscissa the mean potential [a] energy concentration (in WL) during the sampling period is given which was derived from the measurements with the electronic WLM-meter. On the ordinate the corresponding response of the TLDmonitor to radon daughters (difference between both TL-detectors) is displayed, expressed in terms of mRequivalent per liter sampled air. It follows from this comparison a linear relationship over the whole range of 0.005 - 5 WL with a standard deviation of 10%. The resulting calibration factor for the TLD-monitor is 18± 2 mRequiv per WL • 1.

Jan 1, 1981

By Raphael Victor

The construction and modification of tunnels brings a requirement for precise measurement of convergence and divergence to safeguard the structure, maintain safety and provide the assurance needed to maintain efficient progress. Established methods include manual measurement using tape extensometers and automated methods using photogrammetry and automated total stations. Drawbacks include the need for frequent access, power supply, cabling, and cost. The paper describes how the development of reliable optical displacement sensors (ODS) has changed the landscape. ODS sensors are connected to a long-range wireless mesh communications network via a solar-powered gateway outside the tunnel, with data instantly transmitted to the internet. A sensor and its reflector target can be installed in 20 minutes and is maintenance free for a decade. Tunnel movement is measured to sub-millimeter precision with repeatability of ±0.15 mm. Integration of a triaxial tilt sensor allows slope distance to be converted to horizontal and vertical changes and allows rotational movement to be determined. Applications include new-build and long-term structural health monitoring. Case studies will be given, including the refurbishment of rail tunnels in Spain where the ODS measured movement during track lowering in a situation where no other automated system was considered viable.

Jun 13, 2023

By Richard R. Klimpel

The author was the banquet speaker at the 48th Annual MPD meeting, sponsored by the SME Colorado Minerals Processing Section, May 14-16, 1998, in Colorado Springs, CO. Here are his remarks. It has been an exciting experience to have spent 34 years involved with the process of generating patented technology eventually leading to commercialization. In today's terminology, this process is called technology transfer. I have had the unusual experience of being involved doing basic research as an inventor while also being responsible for managing new product development and commercialization. In addition, I worked for 31 years before my retirement for a large research-oriented company, The Dow Chemical Co. In 1995, the company spent more than $1 billion dollars on research and development. The last three years of my career have been spent working with a research-oriented university, The University of Florida. And I have worked as a consultant helping several companies to optimize their products and processes. It is on this cumulative experience base that the preparation of this article is based.

Jan 1, 1998

By C. Bryce

Rhenium is primarily recovered as a by-product from molybdenum roasting circuits. However, rhenium is also present in copper heap leach solutions at very low concentrations and represents a potential new rhenium source. Freeport-McMoRan Copper & Gold has developed a new process using carbon adsorption followed by ion exchange or solvent extraction to concentrate rhenium from less than 1 ppm to 15 g/L. The product is compatible as a feed to an existing rhenium processing plant. A pilot plant operated at Freeport-McMoRan?s Sierrita mine has demonstrated the technical and financial feasibility of this new process.

Feb 23, 2014