Search Documents

By Piyush Rai, Suresh Kumar Sharma, Punit Paurush

The present study has been conducted in surface limestone mine to select the controllable blasting design parameters affecting the peak particle velocity (PPV) for assessment of ground vibration. The study aims at using two prominent statistical tools, namely, principal component analysis (PCA) and stepwise selection and elimination (SSE) techniques for identifying the key controllable parameters affecting the PPV. For determining the correlation coefficient between blasting design parameters and PPV from 44 field scale trial blasts, multi-variate linear regression (MLR) technique was done. It was found that the PCA and SSE eliminated a huge number of controllable parameters to identify the most important parameters, affecting the PPV. The PCA eliminated 6 number of parameters while SSE eliminated 5 number of parameters, and the coefficients of determination (R2) obtained were 0.616 and 0.584 for PCA and SSE respectively. The predictor equations were evolved, and these equations were used to validate the PPV results for another set of 21 field scale trial blasts. The predictor equations have been found to be fairly accurate in predicting the PPV values. Further, the PCA technique provides very near prediction of PPV with high degree of correlation in comparison to SSE technique. The paper highlights the role of state-of-art statistical tools in selecting the blasting design parameters affecting the PPV in field-scale blasting.

Mar 1, 2021

By R. V. Ramani

Demands on available lands will continue to increase due to the projected increase in population and industrial expansion. Though there is an upper limit on the available lands, the multi-use nature of the lands will make it possible to meet these demands. However, this will not happen without adequate planning. Land uses can be broadly categorized as non-renewable and renewable. Lands with mineable resources can be dedicated at some point in time to the extraction of resources. Such a dedication, however long-term, is only temporary because of the non-renewable nature of the mineable resources. Implied here is that the land will be available before and after mining for other uses. Planning for such lands must have the objective that, as far as practicable, no non-renewable uses are pre-empted and no renewable uses are permanently destroyed. The primary aspects of this planning process will be addressed in this paper, These aspects include a discussion of planning responsibility, data needs and availability, the integration of mine planning and post-mining land use planning and a long-term plan for resource conservation and utilization. Minerals, together with agriculture and forestry products, are the primary sources of wealth. Therefore, to avoid land development that may pre-empt future mineral resource utilization, the local planning groups must be aware of the mineralization and mining potential. Much work needs to be done to identify and characterize the mineral resources. Even more work is needed in land use planning for lands with mineral deposits.

Jan 1, 1982

By Ellen Amoako Afful, Michael Moats, Guang Xu, Ashish Kakoria

Electrowinning and solvent extraction are crucial steps in the production of high-purity copper. However, safety concerns have been raised regarding the acid mist generated from the electrowinning process. The mist generated results in health risks to workers and damage to machinery and infrastructure. Currently, chemicals and pellets are used to control acid mist. However, the effectiveness of these controls may vary depending on the type of organic solvent used in the solvent extraction process, which can influence the generation of acid mist. This study aims to evaluate the impacts of organic solvents and surfactants on acid mist suppression. In this study, an electrolyte is contacted with organic solvents to simulate the solvent extraction. The electrolyte is dosed with 20 mg/L of surfactant at each contact. Acid mist testing is performed on the electrolyte separated from the organic phase at the end of the solvent extraction step. The mist collected is analyzed to determine the level of acid mist generated. The results of this study indicate that organic solvents and surfactants showed significant acid mist suppression, but with somewhat different suppression efficiencies. After first contact, Licorice and the organic, for instance, showed a suppression efficiency of up to 69.7% but its efficiency gradually decreased as the number of contacts increased.

Feb 1, 2025

By Landy Stinnett

"When performing a valuation of a mineral property, a developing mine or perhaps an ongoing operation, the appraiser is typically provided with a range of information prepared by the property owner. This information can include ownership records, geological interpretation, assay data, an estimate of the reserves or resources believed to be on site (tons and grade), mine plans, production forecasts, capital and operating cost projections, and so forth.The appraiser familiarizes himself with the data, analyzes the various reports and then prepares the appraisal. There is usually a site visit, and there may be some effort at comparison of the particular mineral deposit with others in the region or with those of similar depositional characteristics, but for the most part, the appraiser is relying on the corporate documents, tempered by his/her experience in the field. Time is usually of the essence, the cost for the assignment has been trimmed, and therefore independent verification of the various components comprising the underlying data base (legal review, redrilling portions of the deposit, collection of new samples, re-assaying, etc.) is unlikely in most situations.In the case of high-value commodities — gold, silver, diamonds, perhaps the platinum-group elements — there have been numerous examples of the property owners attempting to increase the value of their holdings by nefarious methods. Most of these involve salting the deposit in some fashion; i.e., introducing small amounts of the commodity into samples being sent to a laboratory for analysis so that the resultant assay shows a higher grade (Donaldson, 2002; Greeley, 2001; Lechler et al., 2008 and Meech, 2001). Other schemes to enhance the apparent worth of a property include the use of nonstandard assay procedures, incorrect handling or withholding of the underlying information, and false reporting."

Sep 1, 2016

By Emily Rose

The concept of risk management is applied to multiple aspects of the mining lifecycle including safety, mine design, business plan—anything that affects getting the ore to the mill for production. However, risk management is not a topic that can readily be taught in universities. Many situations require knowledge gained from experience to know how this impacts current and future operations. Recent graduates, who must develop and apply decisions based on geotechnical monitoring, likely have not developed “operational experience” and may not be aware of options and typical applications. Thorough resources that explain different monitoring systems, and when and how to implement them, are available for geotechnical professionals. Accessibility to this information can often cause information overload, leaving one unsure of where to start, without knowing where to start. This paper is intended to serve as a high-level overview of development practices, levels of risk, and risk tolerance for entry-level geotechnical and mining professionals who do not come from a geotechnical background. Summarized detail on typical monitoring practices, types of instrumentation, and how to communicate what the data indicates to key stakeholders are provided.

Feb 22, 2026

By Fred Pena

Cyprus Pima Mining Company is located in the Mineral Hill District of southern Arizona, approximately 22 miles south-southeast of Tucson. Cyprus Pima Mining Company is owned 50.01% by Cyprus Mines Corporation, 24.99% by Utah International Incorporated, and 25% by Union Oil Company of California, with Cyprus having the management responsibility. Cyprus Pima's history has been one of continued expansion from an initial plant of 3,000 TPD in 1957; 6,000 TPD in 1963; 18,000 TPD in 1966; 36,000 TPD in 1967; and 53,500 TPD in 1972. The major reason for Expansion IV was that a large volume of low-grade ore had to be moved to get at a higher grade ore in the course of proper pit development. With mining costs already defrayed, this relatively hard, low-grade material became economically profitable for subsequent milling and concentrating treatment. Similar material previously stockpiled was available for ore treatment. In an effort to meet the continuing search for lower unit costs, the largest milling and concentrating equipment had to be examined. The management of Cyprus Pima Mining Company began investigating autogenous, and semi-autogenous milling in 1964 when two carloads of ore selected from the Cyprus Pima pit were sent to the Koppers--Hardinge Operation at York, Pennsylvania for testing. One car contained approximately 40 tons of hard arkosite and the other contained approximately 40 tons of ore classified as soft Hornfels. The purpose of the testing was to determine the amenability of both ore types to autogenous or semi-autogenous grinding.

Jan 1, 1974

By R. E. Hamilton

Automation is a word whose meaning has been broadened by popular usage to include any labor saving device. We with restrict our usage to the replacement of human judgement by instrumental measurement and mathematical analysis in the control of industrial processes. Mineral concentration is an area which has resisted automation because of the great difficulty in developing measuring instruments which can exist in the rugged environment and can measure useful properties with acceptable accuracy. This is not the only factor limiting progress, but until recently it has been of over-whelming importance. The development of on-stream X-ray analysers, magnetic flowmeters and nuclear density meters for mineral slurries has eliminated this obvious barrier and is enabling us to locate and attack the less obvious problems which still limit our ability to automate concentrators. If we examine the history of automation in industries which are highly automated we find that it has usually gone through three distinct phases. The first phase has been regulation. This is the simplest form of control and involves manipulating some variable whose value is of no importance in order to maintain the value of some other variable which is important at a constant specified value in spite of disturbances which may occur in other variables which affect it. A simple example is the use of a control valve to maintain a constant flow of fluid in a line in spite of changes in pressure in the vessels at the ends of the line. The position of the valve stem is of no consequence, as long as it is within its operating range. Unfortunately we soon run out of variables which can be

Jan 1, 1971

By H. Colin

The basic industry, such as mining, ferrous and non-ferrous, cement and aggregates, stores and handles millions of tons of raw materials, re- quiring often different types of storage, blending and reclaiming systems.

Jan 1, 1980

By N. E. Lehman

Cordilleran metamorphic core complexes in the southwestern United States are areas where middle to late Tertiary low-angle normal faulting has uncovered rocks that were at temperatures sufficient for mylonitization during the early part of Tertiary extensional faulting. Large-displacement low-angle normal faults that separate upper-and lower-plate rocks in metamorphic core complexes are termed detachment faults. The significance of Tertiary detachment faulting in the Basin and Range Province has only become apparent in the past 6-8 years, and the association of mineral deposits with detachment faults has only been recognized in the past few years as well. Crystalline rocks below detachment faults have typically undergone chloritic alteration and brecciation over a distance of a few to a few hundred meters below the fault surface (Fig. 1). Chloritic alteration and brecciation overprinted mylonitic fabrics formed during earlier ductile shearing along the down-dip projection of detachment faults. Rocks that underwent pre-Tertiary ductile deformation and prograde metamorphism were subjected, in rapid succession, to middle to late Tertiary mylonitization, brecciation and chloritic alteration, microbrecciation immediately adjacent to the fault, and subaerial exposure. Lower-plate rocks thus experienced rapid decompression and cooling as a result of tectonic denudation and isostatic uplift (Wernicke, 1981; Davis, 1983; Davis et al., 1986).

Jan 1, 1987

By Ray E. Harris

A resource of 134,400,000,000 tons of minable trona and mixed trona and halite underlies an area of about 1,300 square miles vest of Green River, Wyoming (Culbertson, in preparation)(Figure 1). In 1982, the total domestic consumption of soda ash (refined trona) was 6,667,000 short tons (Kostick, 1983), approximately 90 percent of which came from Wyoming trona. This enormous resource occurs in the Wilkins Peak Member of the Creen River Formation (Eocene). The Green River Formation is derived from sediments deposited in a large lake (Lake Gosiute) that occupied the Green River Basin in south-western Wyoming 38-54 million years ago. The Wilkins Peak Member represents a restricted, evaporite-rich cycle of deposition during which time the trona deposits were formed. A total of 42 trona beds are known, of which 25 are of sufficient thickness and extent to be considered minable (Culbertson, in preparation).

Jan 1, 1984

By G. W. Cutting

Interlocking material balances on complex mineral dressing plants greatly assist in metallurgical investigations: indeed, without such a balance, there is no firm basis upon which to base process performance evaluations. To achieve balances both qualitative and quantitative data must be rationalised in conjunction with the process flowsheet. WSL has developed a range of programs to evaluate interlocking material balances. However, to obtain maximum benefit from the balances, answers of direct value at the process level must be provided: WSL has developed also a range of programs for this purpose. Practical examples are given, which illustrate the benefits obtained from process balances.

Jan 1, 1979

By K. Oraee

Excessive emissions of methane from the coal seams can have a serious adverse effect on both safety and productivity of longwall coal faces. Mechanization of coal faces has increased production possibilities to the extent that normal ventilation systems may not be able to ventilate coal face areas in order to lower methane content in the air to within legal limits. Production increases may therefore be prohibited for this reason, especially in gassy seams. Methane drainage from the coal seam by means of long holes and before production starts can act as a useful remedial action. In this paper a two dimensional mathematical model has been produced. The model that is based on finite elements, simulates a methane drainage system where the resultant risk is linked to the coefficient of diffusion, coal permeability, holes pattern and the duration for which the seam is subject to drainage. It is concluded that methane drainage of this type can assist in achieving production increases in many coals seems, especially where high gas content is a virtue of the seam.

Jan 1, 2010

By Madan M. Singh

A new mining project can raise questions about what effect it will have on the community after it closes. Historically, little was done by communities to plan for and accommodate the changes in the economic infrastructure when a mine project is finished either after the ore runs out or if market conditions deteriorate and make it unprofitable. Projects that were underfunded were generally unable to withstand periodic market downturns. However, data in a recent study conducted by the Seidman Research Institute leads to the conclusion that, even when a mining project is terminated, there can be (and, in the specific case studied, is) a residual beneficial economic effect in the community, which lasts for a long period of time.

Jan 1, 2010

By Mahiyar Nasarwanji, Jonathan K. Hrica, Jonisha P. Pollard, Lydia M. Kocher, Brianna M. Eiter

Within the metal/nonmetal mining sector, fall-related incidents account for a large proportion of fatal and nonfatal injuries that occur in mining in the United States. However, the events and contributing factors leading up to these incidents have not been fully investigated. To help provide a clearer picture of these factors, an analysis of imminent danger orders issued by the U.S. Mine Safety and Health Administration (MSHA) from 2010 through 2017 at both surface and underground metal/nonmetal mine sites revealed that most orders are associated with fall risks. Of these cases, 84 percent involved the workers not using fall protection, fall protection not being provided or the improper use of fall protection. Fall risks for workers most frequently occurred when standing on mobile equipment, performing maintenance and repairs on plant equipment or working near highwalls. In most cases, a single, basic, corrective action — such as using fall protection — would have allowed workers to perform the task safely. Overall, these findings suggest that a systematic approach is needed to identify, eliminate and prevent imminent danger situations. Furthermore, to protect mineworkers from falls from height, frequently performed tasks requiring fall protection should be redesigned to eliminate the reliance on personal fall protection.

By Brian Gettinger, Jim Schlaman, Alston Noronha

"INTRODUCTION The public understanding of green solutions today is based on the definition of sustainability adopted by the Brundtland Commission (World Commission on Environment and Development) in 1987: “development that meets the needs of the present without compromising the ability of future generations to meet their own needs.” Over time this initial definition evolved to identify three distinct factors impacting sustainability that are often referred to as the “Triple Bottom Line”: Economic, Environmental and Social. The triple bottom line approach seeks to drive outcomes that create maximum value for all stakeholders. In the last ten years purveyors of water and wastewater tunnel solutions have found themselves on the wrong side of a politically polarizing issue in the crosshairs of politicians, environmental activists and community groups branding tunnels as expensive, “gray” and not-sustainable. Tunnels under design were stopped and large planned tunnel programs were delayed or canceled. Therefore being sustainable and “green” is not simply using natural vegetation, but creating an asset that meets current and future needs and will not become a future liability. As this paper will discuss, tunnel projects embody a sustainable triple bottom line project well, are equally sustainable as green infrastructure, and have begun to gain awareness for their sustainability. GREEN INFRASTRUCTURE CHANGES TUNNELING LANDSCAPE The green movement quickly swept across the nation in the mid to late 2000’s and was a hot topic in the media and at all the local, regional and national industry conferences. Politicians espoused the benefit of green infrastructure including job creation, urban renewal, aesthetics, property values economics and sustainability. The political microscope was focused the closest on stormwater and wastewater management, particularly in communities responding to combined sewer overflow (CSO) consent decrees from the Environmental Protection Agency (EPA). As communities with CSO problems evaluated their long term control program (LTCP), local government officials and planners began to balk at the huge price tag required for compliance and began looking for alternatives. “Green” infrastructure was proposed as lower cost solution that could be used to offset capital-intensive “gray” infrastructure like new sewers, storage tanks, tunnels, and treatment facilities. In addition, including green infrastructure in a previously negotiated LTCP required a reset on the entire planning process, additional studies and more planning which would push capital investment further off into the future, subsequently delaying unpopular user rate increases. As a result, tunnel projects as well as trenched conveyance and treatment plant projects that had not yet started construction were stopped, delayed or substantially changed."

Jan 1, 2016

By E. McCullough, S. Gaillard

"Diesel particulate matter (DPM) has been regulated by the U.S. Mine Safety and Health Administration since 2002 in underground metal and nonmetal mines. To demonstrate regulatory compliance, DPM samples must be collected and later analyzed by the U.S. National Institute for Occupational Safety and Health (NIOSH) 5040 standard method, but the FLIR Airtec DPM monitor can serve as a complementary engineering tool. The monitor is a handheld instrument that offers near-real-time measurements of elemental carbon (EC), which is a primary constituent of DPM. As part of an ongoing field study, the monitor was used to survey EC in an underground stone mine. This effort was aimed at determining spatial and temporal DPM variations in several key locations. The results of prolonged area monitoring—that is, lasting several hours — revealed that DPM concentrations were diluted substantially as air moved away from the primary production zone, but that concentrations could vary quite a bit in a single location from day to day and between seasons. DPM concentrations were generally lower in winter than in summer, which is consistent with increased natural ventilation airflows during winter. Using a modified sampling cassette, an attempt was also made to sensitize the Airtec monitor to allow for “spot-checking” of EC concentrations — that is, measurements made in several minutes. Preliminary field data showed that the sensitive cassette performed well in terms of providing accurate data that could be useful for rapid assessment of DPM. IntroductionDiesel particulate matter (DPM) is the solid fraction of the exhaust emissions from a diesel engine. It largely consists of elemental carbon (EC) and organic carbon (OC) (Birch, 2003). The World Health Organization International Agency for Research on Cancer classified diesel exhaust, including DPM, as a carcinogen (World Health Organization, 2012). It is believed to cause and/or exacerbate respiratory illness upon inhalation, deposition and retention in lung tissue. Because DPM exists in both the micro- and nanoparticulate ranges, it can bypass typical autoimmune defense mechanisms that keep larger particles out of the respiratory system (Ristovski et al., 2012)."

Dec 1, 2016

By B. W. Stunkard

Hibbing Taconite Company is located by the cities of Hibbing and chisholm near the center of the Mesabi Range, approximately 169 km (105 miles) from the Canadian Border. The plant site is equidistant from these two communities, about 6.4 km (4 miles) from each. A 169 km (105 mile) railroad connects us with the port of Superior, Wisconsin, where the pellet production is loaded into lake carriers for lower lakes destinations. Immediately to the south of the mine area is the world famous Hull- Rust-Mahoning Mine which produced more than 700 000 000 million tons of red ore between the years 1893 and 1973.

Jan 1, 1979

By Qingwen Shi, Yun Zhao, Brijes Mishra

The effect of discontinuities on the fracturing and mechanical behavior of shale has been extensively investigated on a laboratory scale in previous works. It is well agreed that the lamination properties, including discontinuity and lamina properties, affect the behavior of shale. However, it is still unclear how the lamination properties are affecting the stability of the shale roof in an underground coal mine entry. This paper investigated the effect of lamination properties using the discrete element method on a mine-scale entry model as an extension to the previous work conducted on laboratory scale models.

Jan 11, 2022

By R. E. Cook

"Mineral deposits require substantial amounts of energy to transport and be processed into usable form and, as such, present a real processing challenge in that the deposits are never homogeneous and orebody compositional characteristics are all over the map. Extracting the desired mineral(s) from the deposit at sufficient profit margin, despite severe fluctuations in market price, requires process automation architecture capable of supporting an integrated enterprise solution. Such an architecture will encompasses the activities of individuals, process units, process areas, plant level activities, mine management and business planning, and accounting systems. Key to the automation process is the aspect of value generation. This article brings together the various requirements for the automation of a mining enterprise and presents the different aspects of how to obtain value across the entire mining operation.Minerals’ processing sites are historically long lived, with 20-year life-of-mine not uncommon and 75 years not unheard of. Considering that hardware technology advancements are introduced every six months, or less, it is prudent to select process automation systems that adhere to “open” industrial standards versus proprietary based systems. In the minerals processing industry, the key to survival is driving the cost of production per unit volume to the lowest possible level and provide enough profit to sustain operations. Control system architecture and business information technology are rapidly becoming important tools in the quest for productivity. Getting key dynamic business performance information at the right time to the right person or process unit is crucial to successfully achieving corporate goals. The process automation architecture selected must, therefore, be able to integrate to the various networking enterprises and business systems.The mining industry is generally known as an extractive industry that is physically oriented with respect to operations and the activities in which workers engage. Large numbers of people performing manual tasks in difficult surroundings, produce variable outputs. But times are changing – and so are industry best practices. While the nature of work still consists of activities such as ore extraction, ore movement, ore concentration, refinement and logistics, automation innovations are starting to change the nature of many of the production steps. The industry has transitioned from requiring more physical activities by workers to more information management, automated control and collaboration within the operation. Humans are good at situational intervention and nonlinear reasoning and do best when empowered with an overall production perspective. Machines and automation are good at repetitive functions, steady state operation, and managing transitions. Thus, a combination of advanced technology solutions, reliable and useful information and full human contributions are necessary to mining operations for value generation."

Jan 1, 2015

By Hamid Mazouz, Mohammed Hakkar, Rim Jouraiphy, Fatima Ezzahra Arhouni, Ahmed Mahrou, Aziz Boukhair, Mohammed Fahad

The wet process is the most commonly used worldwide for phosphoric acid (PA) production, in which phosphate rock (PR) is reacted with strong acid mainly sulfuric acid. This work aims on studying the rare earth elements (REEs) distribution during the production of phosphoric acid using different qualities of phosphate through various industrial technologies. At the onset of this work, the process started with 12 samples of PR, PA, and phosphogypsum (PG) being taken simultaneously from two different Moroccan basins (Ouled Abdoun mine represented by K09 and Gantour mine depicted by G10, G20, BG) and various production lines at two processing platforms (Jorf Lasfar and Safi). Afterward, collected samples were prepared and analyzed for REE characterization using an inductively coupled plasma mass spectrometry (ICP-MS). Based on the analysis results, a transfer factor ( TFX) was introduced with the aim of gauging the REE distribution between PA and PG. The results showed that the total concentration of REEs in different phosphate qualities ranged from 411 to 631 ppm; the major part of this concentration was attributed to the four elements: Y, La, Ce, and Nd which constitute more than 77%. The REE distribution between PA and PG depends on neither the phosphate quality nor the industrial technology used since that the distribution results showed that 55 up to 66% of the initial REEs in phosphate rock ended up in the PG. The behavior of each REE was common except for the element scandium, which transferred mainly to the phosphoric acid.

Nov 3, 2021