Search Documents

By S. Natansohn

A prevalent technique for the recovery of silver from wastes generated in silver-tungsten electrical contact fabrication is electrowinning. Such scrap is placed in a permeable plastic basket which constitutes the anode compartment and this basket is suspended in a larger cell in which the cathode is mounted. A silver nitrate solution is used as the electrolyte and, upon application of an electric field, the silver migrates to the cathode where it deposits out. At times, there is tungsten migration to the cathode compartment and consequent co-deposition with the silver. This W contamination, which may amount to several thousand ppm, necessitates additional purification of the deposited Ag and its removal would therefore be advantageous. The elimination of the W impurity would also extend the operating period of the cell with corresponding increase in the Ag output and savings in labor costs.

Jan 1, 1982

By Larry F. Brown

Mining has been the mainstay of the Woods Creek Valley for more than a century. The head of the valley is at the Continental Divide, about 50 miles west of Denver, Colorado. First, it was the quest for gold and silver that drew people to the valley. Then, when molybdenum was classified as a strategic metal by the U. S. Government during World War I, it was the valley's molybdenum mineralization which attracted the most attention. Molybdenum is used primarily as an alloying material in superior grades of steel. Circumstances responsible for providing the label "Urad" are unknown, but Urad is variously reported to be an acronym for "Uranium Research and Development" or "Uranium Research of America Division". The search for uranium was fruitless as no ore grade uranium exists in this area. The moly orebody was first developed and mined by the Primos Exploration Company from 1914 to 1919. During World War II, the mine was purchased by the government and turned over to the Molybdenum Corporation of America to operate. In 1963 AMAX Inc. purchased the property for $2 million. After spending nearly $30 million for exploration and development, AMAX put the mine into production again in 1967.

Jan 1, 1984

By H. Simpson

Middelburg mine is an opencast export mine operating in the Eastern Transvaal Coalfields of the Republic of South Africa (Figure 1). The mine was commissioned in 1983, to its original design capacity of 4.25 million sales tonnes which was subsequently raised to 5.5 million sales tonnes in 1989. This increase in export tonnage was brought about through an increase in the mines export allocation and the revision of management strategies. The maintenance of this increased tonnage with minimal additional capital has been achieved through improved operational efficiencies and the upgrading of planning operations through the purchase of an Enhanced Mine Scheduling Software Package (EMSSP/MINESTAR). Simultaneously with this requirement were additional factors that contributed to the implementation of the EMSSP. The mine was owned by a joint venture of two partners and is operated by Middelburg Mine services (Rand Mines Pty. Ltd) (Figure 2). This structure of ownership required the evaluation of numerous planning options to be under-taken concurrently and hence the need for an efficient streamlined scheduling pack-age that could fulfill this requirement. Compounding the EMSSP needs further, were the problems experienced in the export market, these being the external pressure from current and new suppliers in the market place which obliged management to provide solutions to rapidly changing market conditions. These fluctuating market conditions have had a direct effect upon the mine's planning strategies because of the large percentage of the mine?s sales sold on the international spot market. The sanction factor for all South African exporters has had a negative effect upon price and this was compounded further through internal competition in 1987 via suppliers attempting to maintain the market position.

Jan 1, 1991

By A. A. El‑Midany, O. M. Asem, S. E. El‑Mofty, M. F. Abadir

Glauconite is a clay mineral that is most probably mined with phosphate and represents a challenge for phosphate upgrading by flotation. Reverse flotation is a common method for removing silica and silicate from siliceous phosphate. Thus, a systemic study was conducted to determine the effect of clay and its interactions with siliceous phosphate ore components on its cleaning by flotation. The flotation of each mineral (phosphate, quartz, and clay) was tested in terms of product recovery using quaternary amine at pH 9. In addition, the settling behavior of each mineral was investigated with and without quaternary amine. Binary and tertiary systems were studied to investigate the interactions between the main ore-containing minerals. The results of each mineral flotation test showed that quartz has the highest floatability, with low floatability of both phosphate and glauconite by quaternary amine. The presence of glauconite does not affect the phosphate recovery, whereas glauconite reduces the quartz floatability, which deteriorates the quartz removal from phosphate. Finally, the interaction mechanisms in the different systems are illustrated.

Apr 5, 2024

By F. Arslan

Gold extraction from refractory ores is still a problem. Gold losses in the cyanidation process are mainly due to the presence of sulfides and carbonaceous materials. Oxidation of carbon and sulfide minerals by sodium hypochlorite is a possible method to render the ore amenable to cyanidation, and earlier work by the USBM indicates that electrochemical generation of hypochlorite is promising. Laboratory work was carried out on the oxidation of pyrite and carbon in an electrochemical cell with a sodium chloride electrolyte. The results of preliminary tests are discussed in relation to the mechanism of electrooxidation of refractory gold ores and the estimation of current efficiency.

Jan 1, 1991

By John Barakso

The Sam Goosly or Equity silver deposit is fundamental- ly a discovery based on the analysis and interpretation of reconnaissance geochemical samples. The discovery was made by Kennco in an area of heavy forestation and wide- spread cover by thin glacial debris. No major mines had been discovered in the vicinity of the discovery prior to the geochemical reconnaissance, and the interpretation of the geochemical results therefore was based on data available through geologic mapping and the sample collection process. In the period 1959-1961, PE. Hirst and his crew, in 1962- 1965 P.T. Blackand his crew, and in 1966-1967 C.S. Ney and P.T. Black and their crew collected geochemical samples from the area of what is now the ore body. Several of these samples were compiled and reanalyzed in the winter of 1966- 1967 for various trace elements, including fluorine. A strong, almost 16-sq-km (10-sq-mile) fluorine anomaly was projected along with a very weak heavy metal anomaly. On the basis of this anomaly, a chalcopyrite-bearing quartz monzonite was discovered in 1967. This was a misleading, noneconomic discovery not associated with the Sam Goosly discovery. The interpretation of the geochemical data by Barakso that summer indicated that another source was responsible for the fluorine anomaly. The conclusion was based on the assemblage of trace elements. Therefore C.S. Ney recommended further regional soil sampling to check the original data. The early results of this follow-up sampling found over 33 ppm silver. First float, then ore outcrop was found in the area of the silver anomaly. The attached reprints complete the development of the property after the discovery of the outcrop of ore.

Jan 1, 1990

Heap leaching has become one of the prime technologies used for the recovery of precious metals from low-grade ores over the past ten years. The recovery process involves mining and stacking the ore on engineered leach pads, with or without crushing and/or agglomeration, followed by leaching with a low concentration sodium cyanide solution. The metal-bearing, pregnant solution is then processed by zinc precipitation or activated carbon absorption to extract the precious metals. The leaching process continues until all economic metal values are removed at which time the spent heap leach pads, the leached materials and excess process solutions require decommissioning. The management of these solutions may present a potential challenge for successful and environmentally sound decommissioning due to their composition, volume or continuity of generation from the spent ore even though active leaching has been terminated. The principal objectives of solution management in decommissioning spent heap leach pads are to meet all operative environmental regulations in a cost-effective manner and to leave the pads in a condition where they do not present a long-term liability either to the operator or to the environment. This involves the reduction in volume of the residual process solutions and/or treatment of these solutions to where they meet applicable water quality criteria. In the past, the environmental and economic aspects of decommissioning and solution management have been overlooked or under-estimated during the planning of mining operations. As a result, there is a potential for long-term liabilities and costs to be recognized only at the end of active leaching, a time at which operating revenues and cash-flow are minimal. Therefore, the decommissioning process requires addressing at the mine planning stage and agencies now require that a plan for solution management after the cessation of operations be submitted prior to initiation of mining. This paper discusses aspects of process solution management during decommissioning, both in terms of quantity and quality, and how potential issues may be recognized and planned for in the initial stages of heap leach design.

Jan 1, 1992

By J. A. Pigott

Undercut-and-fill mining is a method developed by the International Nickel Company to deal with abnormal pillar mining conditions at one of its mines. Results have been such that its use has been extended to normal, pillar recovery operations in other mines of the Company as a replacement for conventional square-set pillar mining. It is anticipated that the method will also largely replace square-set stoping at INCo mines, especially for mining at deep horizons.

Jan 1, 1962

By T. D. Parris

At the Frood Mine of International Nickel, tests were begun in March 1966 to evaluate the use of low profile diesel Load- Haul-Dump equipment in cut-and-fill operations. In December 1966, this test was extended to drawpoint loading of caved ore at the Creighton Mine. The results of these tests conclusively demonstrated the effectiveness of this equipment in the operations at International Nickel. This paper describes the equipment used, the operation of the equipment, production data and operating details. Also discussed in the paper are other trackless equipment which works with the Load-Haul-Dump carrier. Production and Safety comparisons are made with the slusher method in bulk mining, giving the reasons for replacing the slushers at the mines of International Nickel Company of Canada, Limited, Ontario Division.

Jan 1, 1969

By R. T. Langland

The U.S. Bureau of Mines has conducted underground tests and computer analyses to study coal mine roof behavior. Southern Ohio Coal Company provided test sites it) their Heigs mines located near Athens, Ohio. Testing apparatus was adapted for monitoring roof behavior at the face of mining from a remote surface location. Finite element analyses were applied to study the structural conditions present. Test sites were located at three different intersections of entries and crosscuts of the room-and-pillar mine. Electrical read-out instruments were used to record roof bolt loads, roof sag, and roof-floor convergence. They were installed during the roof bolting cycle of a conventional mining section and data was recorded for several months. Normal mining operations continued throughout the test period with minimal interruptions due to the installation and monitoring of the instruments. A computerized data acquisition system, partly underground, partly on surface, permitted continuous monitoring of data and its retrieval, display, manipulation, and storage. The finite element code used to model the test sites accounted for three-dimensional geometry, nonlinear material behavior, and the mining excavation and bolt installation sequences. Results of the test are highly variable. Comparable values between test and analysis results were obtained by applying statistical averaging of. roof test data. Results of the analyses indicate that bolts have a lesser effect on the gross behavior of mine roofs than has been indicated and that bolt load changes are strongly influenced by mining excavation sequence, bolt-placement sequence, and face distance

Jan 1, 1977

By Alan T. Nelson, Ronald D. Mariani

The Tilden concentrator was originally constructed in 1974 for the processing of low grade hematite. Flotation is a key concentrating process in the operation, and therefore flotation optimization has been a major concern since the plant startup. This paper will discuss some of the modifications made in the process to achieve optimization. The conversion that now enables the plant to process magnetite as well as hematite also will be discussed. INTRODUCTION The Tilden Mine, located in Ishpeming, Michigan, is managed by Cleveland-Cliffs Iron Company and is owned by Cleveland-Cliffs and two Canadian steel makers. It was constructed and started production in 1974 and expanded in 1979 for processing a low grade, fine-grained hematite iron formation for which there was previously no technology available. Several papers have been written describing the unique character of the concentrating operation. The hematite plant consists of 12 grinding and concentrating lines, which utilize two stages of autogenous grinding with crushing of an intermediate sized product. The ground product is deslimed in a highly dispersed alkaline environment to reject silica. Corn starch, the flocculant, has a high affinity for iron at the operating pH range of 10.5 to 11.0. The ore is upgraded from 35% to 45% iron in the desliming step. The deslime thickener underflow is the feed to flotation. Each flotation line consists of a bank of 10 rougher cells, followed by four scavenging banks incorporating 5, 4, 3, and 3 cells each. The Wemco flotation cells are each 14.1 cubic meters (500 cubic feet) in volume. A total of 12 flotation lines are available. [ ] A reverse flotation process is employed, using a straight-chain, 8 to 10 carbon primary ether amine silica collector. At the levels used in the circuit, the amine also serves as a frother. A final concentrate is produced in the rougher cells. The concentrates from the four scavenging steps are combined and recirculated to the feed end of the roughers, with the fourth scavenger froth being discarded as a final tailing. Upgrading to about 65% iron is achieved, with control of the circuit based on final concentrate silica grade. Starch is again used, this time as a depressant for iron. During the years of operation, several key areas of the flotation process have been targeted for optimization. The most significant improvements have been realized in the following areas: *Grade Control Automation *Control of Water System Chemistry *Flotation Spray Water This paper will focus on these areas, but other minor improvements also will be briefly discussed.

Jan 1, 1993

By John W. Barnes

In seeking cost reductions, control methods are a fertile field because they significantly affect labor and other costs. While process control in uranium mills is excellent by the evidence of high recovery, the costs seem high to those familiar with extractive operations for other metals. To some extent this high cost is inevitable, because of exacting quality control-, the technically complicated recovery processes; poor control over grade and nature of mill feed- special problems arising out of the radioactive property of the material. Practices used in uranium mills and the limitations indicated for instrumentation and automation are discussed. It is concluded that any large investment in automatic controls should be preceded by a careful study of their reliability and maintainability, and an estimate of the net income after taxes smaller plants my find it more profitable, or at least less risky, to concentrate their efforts on the possible reduction of some control problems and to development of a stable force of skilled employees. The observed experience does not inspire optimism that ore-dressing plants can be extensively automated although certain unit operations offer a challenge for improvements in instrumentation and machine design.

Jan 1, 1960

By Miguel Angel Ibarra

This paper describes the results of a digital computer simulation study in which the impact of the proposed truck dispatching on the overall mine productivity was investigated for an operating open pit mine. In the study, the existing operation was first simulated for a one-month period, using both the actual time study data and the computed cycle times. By adjusting certain input parameters to the simulation program, the actual one month production was first duplicated through simulation. Afterwards, the operation was again simulated in a dispatch mode. Comparison of simulation results under the dispatch mode, with the initial base case simulation results, showed a definite improvement in overall productivity with dispatching; i.e., approximately 10% gain for the operation. As expected, the results also showed that the extent of possible improvement did vary with the particular pit configuration being investigated.

Jan 1, 1980

By K. V. Godfrey

With the increasing need to exercise better control over mill circuits has come a requirement to develop rapid, accurate means of measuring circuit parameters. One of the most important parameters is the assay of the material in the circuit (or about to be introduced to the circuit). To date, most on-stream analysis has been performed using X-ray fluorescence equipment. Neutron activation offers an alternative method in certain circumstances, and one which has several interesting advantages. Recognizing the need for a simple, safe neutron activation unit suitable for on-stream analysis in the mineral industries, Atomic Energy of Canada Limited has designed, built and tested the SHERLOCK system. One prototype (SHERLOCK I) is located in Ottawa and is now used primarily in research. A second prototype (SHERLOCK III) is located in Vancouver at the laboratories of B.C. Research. This unit is being used for some development research and for evaluating the unit in specific applications. Most of the work completed to date has been aimed at proving the technique and in developing some of the parameters needed to design systems for a milling plant. Funding for the work has been through research grants and through sponsor¬ship by interested companies.

Jan 1, 1971

By Ewan Wingate, Ranjit Prasad, Yanjun Liu

The phosphorus journey begins with the extraction of primary phosphorus in the form of phosphate in apatite through openpit mining and, in some rare cases, underground mining methods. The ores are processed in beneficiation plants to remove impurities before the phosphate rock concentrate is either sold on the open market or converted into phosphoric acid in downstream chemical production facilities by the wet acid process or thermal phosphorus routes. These can in turn be converted into fertilizers, as well as used in the food and electronic industries. The advent of the EV battery has given rise to a new use for purified phosphoric acid in the production of lithium ferro phosphorus (LFP) cathode material for EV battery cathode assemblies. The production of LFP relies on raw materials such as lithium carbonate, lithium hydroxides, iron salts and purified phosphoric acid.

Feb 1, 2024

By George O. Lower

The use of cyanides in the extraction of gold and silver is well known.1 Such extractions employ con¬centrations of cyanide in the range of 0.02-0.25 % sodium cyanide equivalent in leaching cycles of 24-48 hours and frequently longer. Copper minerals, even though minor components of precious metal ores, dissolve in these cyanide leaching solutions, consume cyanide, cause fouling of mill solutions, and thus interfere with the precipitation and recovery of gold and silver. 2,3,4 This paper presents a summary of laboratory investigations on the use of cyanide solutions as extractants for copper from various copper-bearing ore fractions. In view of the metal contents involved, it will be apparent that larger quantities of cyanide are required to extract copper than for the extraction of precious metals. In cyanide solutions of concentrations generally favorable to copper extraction, sulfide and oxide copper minerals were found to dissolve rapidly at room temperature and atmospheric pressure. For example, on products in the flotation size range, the major portions (e.g. 65-85%) of the extractable copper frequently dissolved in 2-10 minutes. At coarser grinds, e.g. 100% minus 28 mesh and 100% minus 10 mesh, 75-85% of the total copper was extracted in 30 minutes.

Jan 1, 1966

By Richard Chojnacki

The western united States is not usually noted for the production of fluorspar; however, many significant fluorspar districts do occur in the Rocky Mountain region and constitute a resource of sizable dimension and major potential. This is particularly true within the area of the West served by the rail lines of the Union Pacific Railroad (see Figure 1). Fluorspar deposits near the Union Pacific have produced over 1.3 million tons of finished fluorspar products from 2.3 million tons of ore. Approximately 80% of this production was of acid-grade and 20% of metallurgical-grade fluorspar. Production of ceramic-grade was negligible. Through the years substantial production has come from eight mining districts. Five of these have produced metallurgical-grade and three acid-grade. The best-known fluorspar producing area in the West is the Jamestown Mining District. It was one of the first producers of fluorspar in the western United States and is estimated to have produced over 500,000 tons of finished fluorspar from over a million tons of ore. The district encompasses approximately 36 square miles in central Boulder County, Colorado, about 9 miles northwest of the City of Boulder. Although small shipments were made from the district as early as 1873 or 1874, significant sustained production was not achieved until 1940 when the General Chemical Company, now a division of the Allied Chemical company, acquired the Alice, Burlington, Chancellor,

Jan 1, 1971

By Jerry M. Whiting, Landy A. Stinnett

The subject of this paper is broad and complex. Secondly, it is near and dear to the authors' hearts. Therefore, it doesn't seem possible to deal with every aspect of it in less space than a good size textbook. Also, if we dealt with all of the basics of feasibility studies and report preparation, we would cover a lot of material available in the literature, and would have to minimize our editorial comments. In view of these limiting realities, we have chosen to discuss selected facets of the subject, and to provide several comments which stem from our personal experiences during the past 20 years. "Think Ahead" hen someone is undergoing training to command a large ship, the following short phrase is engraved in his memory: "Think Ahead." The reason is simple enough. A battleship, aircraft carrier or oil tanker cannot change directions quickly, and if one waits to a what the other ship is going to do, there may be twisted metal and bodies scattered all over the ocean floor. The commanding officer has to use radar, forward rind aft lookouts, experience, common sense, intuition, weather forecasts, and everything else available to him to avoid trouble. Remember the USS Stark, and the fate of its captain? The fact the Stark was hit by a "friendly" missile didn't lessen the damage. How about running into a mine? Is it an excuse that no one thought about the possibility of a minefield ahead of the ship? The point is, relative to feasibility studies, that its prospective authors, and especially the commander of the efforts required to create it, must "think ahead" from the moment of their association with 4 mining activity. They must

Jan 1, 1987

By R. B. McCammon

Four areas have been identified as favorable drill-site locations for determining whether or not a suspected prophyry copper deposit exists in Rowe Canyon, Nevada. Favorability is based on the similarity to a deposit model constructed from geochemical data for the porphyry copper deposit near Ely. Favorability is defined as the coincident number of positive anomalies for the elements zinc, silver, arsenic, antimony and iron. The favorable areas coincide with an observed magnetic high and areas in proximity to major faults.

Jan 1, 1979

By J. D. Isbister

Coal is the most abundant and most economical source of energy in the United States, however, combustion of coal results in release of pollutants to the environment. The release of sulfur dioxide and oxides of nitrogen during combustion of coal contributes to the deterioration of the environment. Energy independence in the United States must include the increased use of coal reserves. Increased reliance on coal for energy will dictate the necessity for making coal a cleaner fuel. New technologies employing a variety of techniques from harsh chemical treatment to mild physical separations to clean coal are rapidly becoming available. Success for any coal cleaning process is in economics which translate into efficient removal of sulfur with high recovery of combustibles as well as low capital and operating costs for the process. Conventional coal cleaning processes remove water soluble sulfates and a portion of the pyritic sulfur and ash from coals. Removal of additional sulfur from coals requires more advanced coal cleaning techniques. Coal contains many organic sulfur forms which are the most difficult of the sulfur types to remove from coal. The heteroaromatic sulfur species, such as the comlex thiophenes, are the most commonly found organic sulfur forms. These sulfur forms are resistant to chemical attack and are considered to be refractory compounds. Atlantic Research Corporation has developed an "unique" microorganism, CB1 (Coal Bug 1), capable of oxidizing thiophenic sulfur in coal to form water soluble sulfates.

Jan 1, 1986