Search Documents

By D. S. Flett

Abstract. The commercial importance of hydroxyoximes as extractants for copper has given impetus to basic studies on the chemistry of metal extraction by these compounds. The discovery of accelerator compounds which produce catalytic effects on hydroxyoxime extraction rates has led to mechanistic studies of these rate processes. While these studies have highlighted the importance of interfacial chemical reactions in the extraction process, it is not yet possible to unambiguously describe the mechanisms of metal extraction in these systems or the associated catalytic effects. This paper reviews progress in understanding the mechanism of metal extraction by hydroxyoximes.

Jan 1, 1979

By Z. R. Llanos

The petroleum refining industry makes extensive use of catalysts for the conversion of crude oils into more usable products such as gasoline, fuel oil and gas, aromatics, and others. Catalysts used for hydraprocessing contain cobalt-molybdenum or nickel -molybdenum, although there are catalysts that also contain tungsten. During hydroprocessing, nickel and vanadium are deposited on the catalysts, eventually rendering them inactive. The refiners are then confronted with the problem of disposing the spent catalysts. In the past, landfilling was a common method of disposal and it is still practiced in some countries. Other refiners prefer to stockpile the spent catalysts at the refineries until the price of metals warrants their sale to metal reclaimers. This practice, however, poses environmental problems to the refineries for storage and disposal of spent catalysts. Other types of catalysts are amenable to regeneration. The purpose of this paper is to focus attention on the recovery of nickel, cobalt, molybdenum, vanadium, and alumina from spent hydroprocessing catalysts by Gulf Chemical and Metallurgical Corporation and to review the use of sodium hydroxide and sodium carbonate for pressure leaching of spent catalysts.

Jan 1, 1986

By M. L. Harris

Coal dust produced during the mining process is a prime explosion hazard in underground coal mines. To inert the coal dust and prevent a catastrophic propagating dust explosion, rock dust is applied to the roof, ribs, and floor surfaces of mine entries. Currently, one determination of whether a mine is adequately protected from the coal dust explosion hazard is made by analyzing collected mine dust samples for percent total incombustible content (% TIC). A minimum of 80% TIC is required per 30 CFR 75.403. The as-received moisture of the dust sample is included in the % TIC. Moisture and humidity within a coal mine vary greatly with the seasons, with explosions occurring more frequently during dry winter months. This paper will discuss the fluctuations of the as-received moisture content of the mine dust samples collected by U.S. Mine Safety and Health Administration inspectors in 2010 and the observed fluctuations of the moisture content of rock dust within the U.S. National Institute for Occupational Safety and Health Office of Mining Safety and Health Research Bruceton Experimental Mine and the Safety Research Coal Mine over a one-year period.

By John E. Appleby

Grupo Acera, HYLSA originated in 1942 when Hojalata y Lamina began operations to supply steel strip for the Cuauhtémoc Brewery, the parent company. Production began in April, 1943 with growth accelerated because of World War II. By 1948 the company was producing its own steel from electric furnaces charged with scrap iron. Further expansion was hampered by the fluctuations in availability, price and quality of scrap iron. As a result, a search was made for a suitable process to enable HYLSA to satisfy its need for a reliable source of feed for its steel-making facilities. Their relatively low iron requirements at the time did not justify the very high capital investments required using the conventional blast furnace method. Processes which by-passed the blast furnaces were very much in their infancy and were not commercially tested. HYLSA then undertook an investigation of the direct reduction processes, knowing full well that much larger companies in other countries had investigated several processes but their work had not established a trend toward direct reduction or any particular process. However, after much effort and persistence HYLSA arrived at a process which suited their conditions. By using Mexican iron ore and natural gas they developed the now well-known H. y L. Process to produce sponge iron. Concurrent with the start of investigations which led to the H. y L. Process, HYLSA began an exploration program for a suitable source of iron ore. Thus in 1951, Cia. Minera Las Encinas, S.A. was formed, culminating in the development of the ore bodies near Pihuamo in the State of Jalisco. Mining commenced and ore was

Jan 1, 1971

By Harland E. Cofer

A computer-assisted resources and sedimentological study of the Andersonville, Georgia kaolin-bauxite district was begun in 1975 under a grant from the Office of Mineral Resources of the U.S. Geological Survey (Grant # 14-08-1110-G-173). A preliminary report on the kaolin and bauxite resources of the district has been placed on open file at the U.S.G.S. in Reston, Virginia; the Georgia-Geological Survey in Atlanta, Georgia; and Georgia Southwestern College in Americus, Georgia. In addition to a resources estimate, the objectives include the determination of the mineralogical variation, sedimentological parameters, and paleogeographic patterns of the deposition of the high alumina materials and their associated sediments. In the process of compiling data for the resources estimate, isopach maps were developed that provide information as to the shape, size, and distribution of the kaolin deposits and the kaolinitic sediments that contain them. These or similar maps developed for other districts can be useful exploration tools.

Jan 1, 1977

By D. Mudd, G. Robertson

"Ask an average non-industry person on the street “What is coal? What is coal mining? What is a coal miner?” The most common answers are coal is something Santa puts in your stocking for being naughty, coal mining is destroying the earth causing global warming, and a coal miner is a person that uses a pick and shovel to dig coal out of the earth. As farfetched as these answers seem, unfortunately this is the opinion of many Americans. Realizing the lack of educational opportunity regarding coal and coal mining, a first-of-its-kind grassroots coal education program known as CEDAR (Coal Education Development and Resource) was created. What started from a general conversation at the December 1992 North Carolina Coal Institute (NCCI) Winter Meeting at the Mid Pines Club in Southern Pines, North Carolina led to the creation, and later expansion of, CEDAR. NCCI President, Gene McBurney, challenged John Justice, NCCI Board Member from east Kentucky, to come up with an idea of how to improve the image of the coal industry, pledging $5,000 from the NCCI as seed money to assist in the development of any such program. John then met with the leaders of Coal Operators and Associates, Inc., (COA) in Pikeville, KY where they agreed to match the NCCI commitment, as well as to assist in the program’s development. After further meetings with representatives from industry, business, and the local school system, CEDAR, Inc. (of east KY) was born. The first year of implementation, the program offered coal education programs to public and private schools in one county in east Kentucky. Although it started in the coalfields of eastern Kentucky, it certainly did not end there. After an amazingly successful first year of the program, it didn’t take long for industry leaders in the western Kentucky coal-fields to learn about, and take note of this new, unique, and exciting program that provided opportunities for teachers and students to learn, “the rest of the story” about the coal industry. Through the joint efforts of Costain Coal, and the Western Kentucky Coal Association, CEDAR of West Kentucky, Inc. was formed in 1994, and has operated since that time, except for the two year period from 2004-2006. The program restarted in 2006 under the name of CEDAR West, Inc. and continues to be offered in six western Kentucky counties."

Jan 1, 2015

By S. Potgieter-Vermaak, T. T. Chiweshe, W. Purcell

The advantage of using ammonium phosphate salt as flux is the selective precipitation of chromium(III) compounds, which are considered nontoxic and environmentally friendly. The technique in this paper is determined to have potential to be applied in the metallurgical industry, where it can be used in the beneficiation of chromite mineral ores. The higher chromium contents of chromite ores often require furnaces to run at higher temperatures of above 1,300 °C, which can cause shutdown of the ore processing plant and accumulation of the sticky chrome compounds — including toxic chromium(VI) waste — which are generated as byproducts. The other advantage of this technique is its low to moderate energy consumption compared to existing techniques.

By D. S. Davies

Further development of the Nitric-Sulfuric Leach (NSL) process has led to an improved design of the leach and nitric acid recovery steps. NO produced in the leach step is reacted with oxygen, regenerating N02, which is sparged directly into the leach reactor. Leaching is simplified to two steps and the nitric acid plant is replaced with an oxidation recycle gas sys-tem. Laboratory work substantiated the concept and led to selection of operating conditions. The lab work also pointed to improved process control compared to use of nitric acid as the sole oxidant. Recovery of copper from purified pregnant liquor is modified to use air agitation electrowinning improving cathode quality and lowering tankhouse costs. Economic evaluation shows reduction of capital requirements from $2400/AT to $2000/AT in 1978 dollars for 50,000 TPY of copper production.

Jan 1, 1978

By Leon Y. Sadler

Equations which predict the unsteady-state response of the continuous froth flotation cell to changes in operating conditions are necessary for the rational design of an automatic flotation cell control system. Unfortunately application of automatic control to froth flotation separation equipment has lagged behind application to other types of separation equipment (for example distillation columns, absorbers, liquid-liquid extractors, etc). This may be due partly to the unavailability of suitable mathematical models for predicting the dynamics of continuous mechanical froth flotation cell. This paper presents the results of a comparison of four dynamic flotation models (in transfer function form) using the same set of unsteady-state continuous flotation data. One of the transfer functions tested has been presented previously in the literature (1), another (2) has been accepted for publication, and two are given here for the first time. In addition, data are presented which confirm earlier findings that the mixing in the rotor-stator type cell is nearly perfect. The specific purposes of this paper are to: (1) provide the automatic control systems designer with several alternative dynamic mathematical models of the continuous mechanical froth flotation cell (2) give some idea of the relative a¬bility of each model to predict unsteady-state behavior by fitting each model to the same set of experimental stimulus-response flotation data and (3) provide more insight into the macro-mechanisms prevailing in the continuous mechanical flotation cell. The dynamic models which are presented and tested here all relate the time variation of the concentration of a given floatable mineral in the tailings to a time-dependent disturbance in the same floatable mineral concentration in the feed to the flotation cell.

Jan 1, 1972

By M. Bai

The influence of mining on the hydro-geomechanical environment is greatly constrained by alternating mining geometries. The limiting magnitudes of surface subsidence and groundwater flow over the mining area, as a result of geometry changes, can be reasonably predicted through a coupled finite-element model introduced in this paper. Verification of the model has been tested using real and conceptual case studies which reveal that changes in strata conductivities are strongly related to the strata deformation induced by mining. The greatest modification of hydraulic conductivities occurs within the caving or severely fractured zones. The study indicates that narrowing the panel face width will substantially reduce both the intensity and extent of mining damage to the overlying strata, limit surface subsidence and constrain the change in hydraulic conductivity to a reduced scale and smaller extent, particularly as mining depth increases.

Jan 1, 1993

By F. Soumis

We propose an advanced truck dispatching system which uses mathematical optimization approaches including integer programming, non-linear networks and the assignment problem. The system produces better operation control than existing algorithms. Furthermore, it provides planning tools for choosing equipment and finding an equilibrium between the quality and quantity of production.

Jan 1, 1986

By G. V. Henderson

Large reserves of high calcium limestone have been outlined in the Redwall formation at Nelson, Arizona. Geologic mapping, core drilling and shallow seismic refraction studies have outlined more than 100 million tons of high quality, chemical and metallurgical grade limestone in the Mooney Falls member of the Mississippian Redwall Limestone. Well developed Karst zones in the Redwall were delineated by field mapping, seismic profiling and core drilling. Development of large reserves of high quality, thick beds of limestone near the present mine and rail facilities was the basis for the current mine and plant expansion. When completed in 1978 the planned 1800 Tpd production will represent the largest lime operation in the Western United States.

Jan 1, 1978

By Gordon M. Pugh, David G. Rasmussen

INTRODUCTION Square-set timbering of stopes developed from stull support methods because veins too wide for stulling were being mined. In general, the void caused by the stoping of the ore is filled with a system of interlocking timbers. Timber framework supports the wall rock, the mining operations, and provides access. A timbered stoping method can be used in all widths of veins at any dip. The timbering can be normal and parallel to the planes of the walls or at angles to these planes. Irregularly shaped ore bodies can be worked by timbered methods. Pinching or swelling of the vein will not adversely affect the method. Timbered stoping is especially advanta¬geous where weak ground is encountered in the vein or the wall rock. The ground is unsupported only until timber sets are stood. These stopes can be filled with sand or waste when desirable. The customary method of developing a square-set timbered stope with haulage drifts above and below and timbered raises on each endline is shown in Fig. 1. The drifts are timbered the full stoping length. The raises have two compartments with the manway and timber slide in one compartment and the chute in the other. The drifts and the raises cannot be widely spaced as handling timbers is an important consideration. Stoping can begin immediately above the drift timber and continue in both directions and upward from the raise. Breasting down each blast round for only one timber set laterally is the common practice. The blasted ore falls to a lower floor where it is slushed or trammed to the chute. Drilling can proceed on the upper floor while broken ore is being removed from the stope. As shown in Fig. 2, square-set timbering may be used in cut-and-fill stopes to support the back and walls until fill is added. There are various ways of developing an ore block for timbered stoping. Fig. 3 depicts the situation for the main haulage in the vein with an intermediate drift separated from it by a sill pillar. The ore is slushed into the chute connecting the two drifts. The situation in Fig. 4 is identical to that in Fig. 3 except that no sill pillar is used. In Fig. 5, the haulage drift development is done in the footwall with crosscuts driven to intersect the ore body. The intermediate drift development is above the crosscuts with a minimal sill pillar. The main bottleneck in timbered stoping is in the timbering process. Drilling in the stope is generally held up while timbering is done. Two or three men are re¬quired to do the timbering and an additional one or two men are needed to transport and raise or lower the tim¬ber. Good organization is essential to timbering. Skill must be exercised in standing the timber to support the ground and still maintain good production. COSTS AND PRODUCTIVITIES Development and stoping costs are presented in Tables 1 through 7 for the situations in Figs. 3 and 5,

Jan 1, 1982

By Paul T. Allsman

The guiding principle in developing this plan resulted from evaluating potential future markets for oil, the quantity of mineable oil shale and the optimum rate of production comensurate with market demand on the available oil from shale. In addition, the rate of production may depend upon a solution to the problems of scarcity of resources other than oil shale. The rate of production finally will tend to establish the choice of technologies with these limits. The principle components discussed will be: 1) The place of oil shale among the various energy sources and its relative adaptability for use in the area of major consumptive demand. 2) A recalculation of the reserves and their classification on the basis of quantity, grade - gallons per ton, - and physical characteristics principally thickness, overburden and depth.

Jan 1, 1982

By D. F. Scott

Spokane Research Center personnel have been investigating the use of seismic tomography to monitor the behavior of a rock mass, detect hazardous ground conditions, and assess the mechanical integrity of a rock mass affected by mining. Seismic tomography can be a valuable tool for determining relative stress in deep (> 1220 m) underground pillars. If high-stress areas are detected, they can be destressed prior to development or avoided. High-stress areas can be monitored with successive seismic surveys to determine if stress decreases to a level where development can be initiated safely. There are several benefits to using seismic tomography to identify high stress in deep underground pillars. The technique is reliable, cost-effective, efficient, and non-invasive. Also, investigators can monitor large rock masses, as well as monitor pillars during the mining cycle. By identifying areas of high stress, engineers will be able to assure that miners are working in a safer environment.

Jan 1, 1997

By Garry M. Hughes

Lynn lake, Manitoha, where Sherritt has operated a copper-nickel mine since 1954, is located north of the 56th parallel approximately SOO miles north of Winnipeg. Sherritt's new, 3,000 tpd, copper-zinc Fox Mine is situated 30 miles southwest of Lynn lake. This paper focuses on the Fox Mine concentrator, hut first some background information. Sherritt Gordon Mines Limited started mining operations as a copper-zinc producer in 1931 at Sherridon, Manitoba, 150 miles south of Lynn Lake. As Sherridon fizzled out development of a series of nickel-copper orebodies commenced at Lynn Lake. The Forward process was developed to treat the nickel concentrate from the Lynn concentrator. Sherritt's ammonia leaching process is now history and is expected to gain more prominence as pressure is applied to the mining industry for closer environmental control. But few are aware of the fact that the present Lynn Lake crushing plant and concentrator were dismantled in the autumn of 1951 and freighted from Sherridon by tractor train during the winters of 1952 and 1953. The copper-zinc orehody at Fox Mine was discovered early in 1961 by geophysical methods which included both airborne and ground surveys. It is part of a ,large body of massive and semi-massive sulphides consisting chiefly of pyrite; with chalcopyrite, sphalerite (containing 7-9% iron) and pyrrhotite in varying proportions which occur within a series of volcanic and sedimentary rocks. The total mineralized zone is a lenticular body with a minimum average length and width of 1,350 feet and 66 feet respectively, to the explored depth of 2,000 feet. The average sulphide content is 67%. Higher zinc zones are masses of pyrite grains cemented by sphalerite with lower than average copper content. Zones higher in copper and lower in zinc are slightly more quartzose. Gold and silver are present in small amounts roughly proportional to the copper content.

Jan 1, 1971

By K. Rushdi, B. E. Abulnaga

The conventional Froude number is blind to the presence of solids, their density and their concentration in a stream of slurry mixture such as tailings flowing in an open channel. This often leads to rough approximations of subcritical, critical and supercritical regimes, based on one phase flow Froude number, limiting subcritical to a value smaller than 0.8 and supercritical to values above 1.4, as proposed in the past by Green, Abulnaga and other authors. While acceptable for small flows, such approximations can be uneconomical for the larger flows encountered in some modern plants that treat up to half a million t/day. A review of concepts of a densimetric Froude number sheds some light on the effect of solids on stratification prior and subsequent to a hydraulic jump. While the approach is heavily borrowed from modern sedimentology, it provides a useful tool to designers of large launders or open channel tailings systems. These concepts are reviewed with some practical examples.

Jan 1, 2013

By Michael G. Zabetakis

Effective accident prevention programs utilize a broad spectrum of activities, including meaningful training programs. In practice, such programs must be directed towards specific, defined needs. These needs are considered here for three categories of employees: new, re-assigned, and experienced.

Jan 1, 1983

By Jerry R. Riding

Metallurgical process methods have seen dramatic improvement over the past fifty years. As these improvements have come about, more and more emphasis has been placed on obtaining accurate and rapid analysis of the metallurgical processes. Well-defined conventional laboratory analysis procedures which have proven to be reliable were developed early in the mineral industry's history; however, these conventional procedures, which have not changed appreciably in fifty years, have the serious drawback that they are too slow to be of appreciable value in automatic control of the processes. For example, the assay results normally become available to a mill operator from eight to twenty-four hours after a sample is taken. Since the desired mineral separation can only be made while the minerals are in the flotation circuit, conventional assay results provide information similar to postmortem reports. Consequently, using conventional procedures, the mill is operated with information from an earlier period of time, which may not reflect current conditions. In recent years there has been a steady increase in the volume of required samples. At the same time, labor, material, and overhead costs have continued to rise causing the cost per assay to reach an alarming level. This rising cost per assay, plus the increasing demand for rapid analysis necessary for control, has caused the mining and metal processing industries to look toward other techniques to solve these problems As a result, X-ray fluorescence which can provide on-stream analysis necessary for control, as well as perform numerous laboratory assays at lower cost and at a much greater speed than conventional methods, has gained wide-spread attention. In addition, multichannel X-ray fluorescent instruments are now available which have been perfected to the point where the analysis of the most important chemical constituents is available within one minute after a sample is presented to the X-ray analyzer. Because of these obvious advantages, extensive use is being made today of X-ray analysis in the mining industry to analyze slags, ores, and mineral content of rocks. The results are used to make quick decisions for both mining and beneficiation of metals. For example, X-ray systems which provide rapid on-stream analysis of the slurries at desired points Fn metallurgical processes have recently been developed. The successful application of these systems has moved the milling process a step closer to fully automatic control.

Jan 1, 1969

By Nenad Spoljaric

Greensand, greensand marl, and green earth are names given to sediments rich in the bluish green to greenish black mineral known as glauconite. The word glauconite is derived from the Greek word glaukos, meaning bluish green. The term "greensand" as a rock name for a glauconite-bearing sediment is more appropriate than "greensand marl," a term that has been doggedly perpetuated in the literature. Because of its potash and phosphate content, greensand was mined and marketed as a natural fertilizer and soil conditioner for more than 100 years. The advent of manufactured fertilizers with adjustable nutrient ratios led to a decline in the use of greensand in agriculture. The material has since been recognized as useful in water treatment. Unfortunately, despite large reserves and world- wide distribution, glauconite has not been utilized to any significant commercial extent because no major application has been found for a substance with its chemical composition and properties. This is probably due mostly to a paucity of research on its potential commercial uses. Extraction of potash received considerable attention during and just after World War I. Because of relatively high extraction costs and a generally low potash content (viz., less than 8%), glauconite lost its appeal as a source of this commodity. Historical Background Greensand was used as a fertilizer in New Jersey in the latter part of the 1700s. During the early 1800s its use became more common; applications of as much as 22.5 kg/m2 were sometimes made, although recommendations for agricultural use suggested 4.5 to 11 kg/m2 (Tedrow, 1957). Many crops, especially the forage type, were said to improve with greensand application; however, because of its slow release of potash, large quantities were required. Certain greensands that contain sulfur and sulfide minerals are harmful to plant growth, and these were classified as poison, burning, or black marls. The availability of higher grade potash salts from other mineral sources and the manufacture of prepared fertilizers displaced the agricultural use of greensand during the latter 1800s. During the mid-1800s the greensand industry, centered in a small section of the eastern United States, grossed more than $500,000/y. Toward the end of the century, however, annual production had dwindled to less than $100,000 in value. By 19 10 there were only six or eight greensand producers grossing less than $5,000/y each (Tyler, 1934). There was a brief revival of the US industry during World War I because of the curtailment of foreign potash, especially from Germany. During the latter 1940s and early 1950s greensand was again recommended as a food nutrient for plants and farm crops. Agronomic studies discussed its potential as a soil additive that gradually releases potash and many trace element nutrients essential for plant growth (Tedrow, 1957). Greensand was sold with the idea that it would condition soil and absorb and hold water while its base exchange properties would release trace elements. For a short time glauconite was used in certain parts of New Jersey as a binding additive in the brick industry, and in the 1800s it was used for making green glass (Cook, 1868). In the early 1900s the base exchange properties of glauconite were recognized for water treatment and the mineral gained acceptance as a water softener. Mansfield (1922) does not mention base exchange even though this phenomenon was known in 1916 or earlier. From 1916 through 1922 several patents for the use of glauconite as a water softening agent were granted. A method was also patented for treating greensand to improve it for water softening and ready regeneration with common sodium chloride brine (Borrowman, 1920, Spencer, 1924, Kriegsheim and Vaughan, 1930). Treated glauconite, on contact with water containing magnesia or lime, takes up magnesium or calcium ions and releases sodium ions. This exchange is limited to the outer surface of glauconite grains, and when all the surfaces have absorbed their capacity, the grains must be regenerated. Regeneration, simply stated, consists of treating or backwashing the glauconite with a sodium chloride solution, which replaces the hard water elements with sodium, thus reviving the glauconite. The process has become more sophisticated due to competition among companies in the water softening business. Greensand products for water softening generally consisted of several different grades distinguished by the particular treatment the glauconite was given during processing. The standard greensand water softener was produced from natural glauconite that was only washed and classified. Its characteristics for water softening are given in [Table 1].

Jan 1, 1994