Search Documents

By T. A. Gray

The environmental liabilities of coal waste disposal sites can have a major impact on a mining project's economic viability. Developing a waste disposal site is no longer simply an exercise in completing paperwork to obtain a permit, with the proliferation of environmental regulations in recent years, managing disposal sites now requires design creativity, short term and long term planning and detailed monitoring to maximize the benefits to the mining company. Operating costs and future capital costs for expansion of existing sites, new site development and regulatory compliance should be reviewed periodically and considered in the overall management plan. This paper discusses various management methods that are being employed in the industry to improve waste disposal operations both environmentally and profitably.

Jan 1, 1994

By M. R. Shahan, W. R. Reed, S. Klima, T. W. Beck

"Testing was conducted to determine the ability of foam to maintain roof coverage in a simulated longwall mining environment. Approximately 27% of the respirable coal mine dust can be attributed to longwall shield movement. Developing controls for this dust source has been difficult. The application of foam is a possible dust control method for this source. Laboratory testing of two foam agents was conducted to determine their ability of foam to adhere to a simulated longwall face roof surface. Two different foam generation methods were used; compressed air (CA) and blower air (BA). Using a new imaging technology, image processing and analysis utilizing ImageJ software produced quantifiable results of foam roof coverage. For CA foam in 3.3 m/s (3.3 m/s (650 fpm)) ventilation at 3 minutes after application, 98% of agent A was intact, while 95% of agent B was intact on the roof. At 30 minutes after application 94% of agent A was intact while only 20% of agent B remained. For BA in 3.3 m/s (3.3 m/s (650 fpm)) ventilation, the results were dependent upon nozzle type. Three different nozzles were tested. At 30 minutes after application 74-92% of foam agent A remained, while 3-50% of foam agent B remained. CA foam seems to remain intact for longer durations and is easier to apply than BA foam. However, more water drained from the foam when using CA foam which demonstrates that BA foam retains more water at the roof surface. Agent A seemed to be the better performer as far as roof application is concerned. This testing demonstrates that roof application of foam is feasible and is able withstand a typical face ventilation velocity, establishing this technique’s potential for longwall shield dust control. INTRODUCTION NIOSH personnel have visited many longwall operations at various geographical locations in the U.S., conducting benchmark surveys to characterize current operating practices and dust control measures in use. Sources of respirable dust generated from the longwall face have been identified as: intake (10%), stage loader (20%), shields (27%), and shearer (43%) [1]. Dust generated from the shearer, armored face conveyor, and the stage loader can mainly be controlled by water sprays and increases in ventilation air quantities, however, research has demonstrated limited effective controls for dusts generated by shield movements [2]. One possible approach to mitigating shield dust generation is to apply a layer of water or foam to the shield-roof interface. Once this interface is blanketed with foam or water, dust will be less likely to become airborne and contaminate the airways over the personnel walkways. Though water is an abundant and common dust control measure, roof applications have limited success because water is unable to remain in-place in adequate quantities for the necessary duration between application and shield advance. Past and current testing of foam for material properties has shown that it has longer applicability times, ranging from 10 to 60 minutes [3] and has shown better performance for dust control, ranging from 19-96% improved efficiency over water [4, 5, 6, 7, 8]. The majority of this foam dust control research has focused on dust control efficiency at the longwall shearer or continuous miner cutting drum."

Jan 1, 2017

By Debra Switzer, Swapnil Urankar, Douglas Watson, Steven Hunter, Chandranth Banerjee, Shashank Pathak

A hydrocyclone is a piece of equipment commonly used as a classifier in mill circuit operations. Traditionally, hydrocyclone performance is characterized by the classification efficiency parameter, such as cut size (d50c), sharpness of separation () and bypass (Rf ). A plethora of endeavors have already been made to develop parametric models to determine hydrocyclone performance that correlate design and process variables. In contrast to those studies, we made an attempt to develop an approach to derive required design parameters purely from hydrodynamic principles that provides a platform to optimize the operation of a hydrocyclone for a given application. In this selection methodology, we calculated the differential pressure at the air core, as well as the tangential velocity at the boundary of the air core from the vortex principle in a confined geometry at different operating regimes. A series of experiments were conducted using Weir’s Cavex® hydrocylone where process variables—such as solids concentration and feed flowrates—were experimentally studied to determine the key classification parameters. For the validation of the current approach we used the same process variables to derive design parameters and compared them with the existing design. The current approach can provide insights towards the selection of design parameters and can be useful for mining industry professionals to optimize different operating parameters of hydrocyclones to achieve the best performance.

Feb 1, 2024

By Ataç Başçetin, Hasan Çelt, Hüseyin Onur Dönmez, Kürşat Hasözdemir

Phenolic foams, known for fire resistance, show broader industrial potential, particularly in mining, through property enhancements. Adjustments to the formaldehyde-to-phenol (F/P) ratio, bio-based additives like lignin, and nano-silica improve foam strength and thermal stability. Density modifications allow foams to range from flexible, low-density forms to rigid, high-density supports. In mining, enhanced phenolic foams could reduce coal ignition risks by acting as oxygen-blocking barriers. Current findings suggest these foams offer viable, sustainable solutions for safety in hazardous environments. Continued development could make them essential for thermal and mechanical applications under extreme conditions. This paper aims to provide a comprehensive overview of the mechanical characteristics of phenolic foams, current enhancement strategies, and standardized testing methods used to evaluate foam properties.

Feb 1, 2025

By D. C. Myntti

An open pit mining equipment maintenance program, in order to be successful, must have many active segments covering the full range of equipment selection, trained personnel, repair facilities, preventive maintenance programs, warehousing, interdepartmental cooperation, paperwork and effective communications. The mine maintenance program is required to protect company assets Which are units of equipment generating revenue. The program should result in reduced unscheduled equipment downtime, increased equipment productivity rates, and decreased unit operating costs. Current maintenance problems; maintenance effectiveness and future projections on equipment maintenance are discussed. Equipment maintenance is big business and the maintenance department is a full-time partner in the mining venture.

Jan 1, 1978

By S. K. Kawatra, S. J. Ripke

During 1998, 62 million tons of iron ore pellets valued at $1.7 billion were shipped from U.S. mines. These pellets are the primary source for domestic iron and steel production. During pelletization, binders are required to improve the green strength of the pellets. Each year, bentonite binder costs a typical plant from $3 million to $5 million. Reducing the bentonite dosage has the advantages of significant cost savings while producing higher quality, lower silica pellets. The authors have recently identified a new and important bentonite binding mechanism, the fiber theory. During this study, procedures were developed that took advantage of the ability of bentonite to form fibers, and resulted in a dramatic decrease in the necessary bentonite dosage. Acceptable quality pellets were produced with the bentonite dosages reduced in half from 14 lb/lt (0.66%) to 7 lb/lt (0.33%).

Jan 1, 2001

"A long-term mine production schedule optimization based on stochastic integer programming is presented that manages the risk due to geological variability and uncertainty while jointly considering mine profitability, truck fleet requirements and waste management. The evolution of the pit is controlled so that space within the mined-out pit is continuously provided to allow for tailings and waste rock to be replaced, thus minimizing the project’s environmental footprint. The method is applied at a taconite iron ore deposit and has a project net present value that is 16.9 percent higher than that of a conventional schedule and has a higher chance of meeting production forecasts. The stochastic schedule reduces equipment requirements by delaying waste mining and by mining selectively in order to meet plant ore feed requirements without stockpiling material, resulting in 23.7 and 26.2 percent lower mining capital and operating costs, respectively. IntroductionThe LabMag iron ore deposit is part of the Millennium Iron Range, a 210-km (130-mile) belt of taconite in northern Quebec and Labrador, Canada. LabMag has significant economic potential. It contains more than 3.3 Gt (3.6 billion st) of proven reserves at an average total iron content of 29.8 percent and is very low in impurities. However, on a project basis of 23 Mt/a (25 million stpy) of product, the required capital expenditure is estimated at more than $5 billion (SNC-Lavalin, 2014), which necessitates careful evaluation of all sources of risk. Resource estimation is one of the main sources of risk in a mining project as knowledge of the orebody is primarily based on drilling, which is often sparse because it is expensive. If the expected ore tonnages and qualities are not obtained when mining, the project cash flows are directly affected. The expected quantities and qualities of ore and waste are defined by the mine production schedule, which specifies the sequence of extraction and is dependent on the resource estimation. The goal of mine production scheduling is thus to maximize the expected profit, while also meeting all production targets and constraints, by creating an extraction schedule that is robust in the face of geological risk and has the highest chance possible of actually being realized."

Jan 10, 2017

By Alexander N. Winchell

The construction and erection of the Coleraine concentrating plant was commenced in April, 1909, and was completed (with the machinery installed) ready for use in 1910. Attached to the main building is 'a table house large enough to accommodate con¬centrating tables for five units and space for a small machine shop and supply store. For the handling of the' railroad cars in the upper portion of the mill there is provided on the north side of the main structure a trestle approach 650 feet long, and on the south or opposite side a tail track 300 feet long. The latter is so constructed as to permit its being incorporated directly in a possible future extension of the plant. The building, viaduct approach and tail, trestle, as well as the table house, are con¬structed of steel, the total amount used being 6,100 tons. The building is covered by corrugated' steel sheeting over 2 x 6-inch wood sheathing fastened directly to the structural steel. The north end of the trestle approach is connected with the main road-beds forming the track system for delivery of the crude ore to the plant over an embankment of a maximum height of 110 feet containing over 2,000,000 cubic yards of dirt.

Jan 1, 1920

By Vittorio Manassero, Antonello de Risi, Filippo Cavuoto

"This paper deals with an innovative mechanized method to bore and simultaneously line circular shafts, adopted in the Naples Metro project for the installation of 10 vertical shafts for ventilation purposes. With this method, excavation of shafts is carried out under a positive head of stabilizing fluid by a milling machine, temporarily set at the bottom of a permanent lining made of precast reinforced concrete segment rings. The debris is evacuated by inverse fluid circulation. The shafts in Naples are 4.5 m I.D., from 34 to 44 m deep and they are all located downtown in a highly urbanized area. They were bored and installed into volcanic soils under a hydrostatic head of up to 30 m. Displacements and groundwater level were constantly monitored to keep control of the effects on the surrounding buildings and utilities. INTRODUCTIONThe extension of Metro Line 1 in Naples (Italy) from the previous terminal of Piazza Dante to Piazza Garibaldi is also called the “low stretch”. Most of it runs along the coastline, encompassing the historical city center, the Greek-Roman Neapolis. The Metro Line crosses under densely urbanized areas for the whole way (Figure 1). It runs beneath Via Toledo, which follows the layout of the ancient Aragonese walls. The first station (Toledo) is located halfway along this street. Then, after a wide bend, the line reaches Piazza Municipio, where the second station is located. From there, the line moves along the axis of Via Depretis and Corso Umberto I, where the stations Università and Duomo are situated. The fifth station is in Piazza Garibaldi and the end of the stretch is located at the Naples Business Center. The twin single track tunnels were bored into volcanic tuff by TBM. This design choice simplified by far the construction of the tunnels and reduced to practically zero the interactions between tunnelling and surface buildings and utilities. Nevertheless, this choice entailed that the line had to be located at depths to the order of 35-45m below ground level and 30-35m below the water table. At each tunnel segment between stations, a pair of ventilation chambers were constructed (10 in total). Each ventilation chamber is connected to one TBM tunnel by a vertical shaft and a horizontal drift at the base of the shaft. The shafts, in addition to tunnel ventilation, provide a safety access/escape."

Jan 1, 2016

By C. V. Deutsch, T. Acorn

Understanding and managing risk is of increasing concern for the mining industry. Although methods exist to model geologic uncertainty based on stochastic modeling techniques and multiple realizations, there are few approaches to manage this geologic uncertainty in pit optimization. Block values can be penalized if the block uncertainty is high, but the goal here is to consider the reserve risk within the pit. This paper presents an approach for pit optimization that considers all realizations simultaneously with a heuristic pit optimizer. The heuristic algorithm maximizes value and also penalizes reserve risk. The inclusion of multiple realizations provides access to the risk or uncertainty in the total pit value. Considering this information permits an active risk management approach that can manage the uncertainty in the reserves within the entire pit.

Jan 1, 2018

By Lauren M. Roberts, Ralph R. Sacrison

Pipeline or borehole free-fall transfer of material has long been done in support of underground mining. This paper addresses some characteristics and design elements in selecting systems suitable to the transferred media and the mine requirements. Though aspects of overall systems are discussed, principal attention is directed to the slickline/dropline/transfer line and the discharge diverter/rockbox/energy dissipator/boot. These terms are common to these systems, often used interchangeably, and will be used as appropriate to the material, equipment and construction. Following several design sections, fabrication and construction, and system operating and maintenance procedures are discussed.

Feb 1, 2025

By Ken Goering, Steve Kral, William Gleason

"Once every four years, the global mining industry gathers in Las Vegas, NV for MINExpo International. According to the show’s organizer, The National Mining Association (NMA), about 44,000 people attended the three-day show from Sept. 26-29. It was a show that featured the latest and greatest in equipment and technology. It also served as the backdrop for a snapshot of the state of the industry and while the picture of a global industry is never completely clear at any one time, one thing that is evident is technology has become a major force in the way mining is done.Had it not been for the awe-inspiring “iron” that was on the show floor in the form of haul trucks and shovels weighing hundreds of tons, one could be forgiven for thinking that they were at the Consumer Electronics Show. From training simulators designed to give a realistic experience of operating mining equipment to virtual reality technology that can take the user into the depths of an underground mine or the middle of a mapped ore deposit, an overriding theme of MINExpo 2016 was that the mining industry is connected like never before.In the north hall of the Las Vegas Convention Center was the GE Mining booth that was designed to showcase its efforts to help create a mine that will be connected from the front office to the face of the underground wall or bottom of the openpit. GE Mining called its booth a digital mine, and it included a suite of technologies that can improve performance, reliability, safety and operations. GE Mining said it views each mine as a mini-city, requiring power, water and transportation. Intelligent, real-time monitoring across the mine allows operators to make data-driven decisions that improve equipment reliability and optimize mine operations for substantial savings. And GE Mining was just one of many exhibitors showing off software that allows various types of equipment to communicate. Its booth sat in the shadow of the Komatsu booth with its new 360-t (400-st) 980E-4 haul truck that included GE’s 360-t (400-st) electric wheel motor. This is just one example of how technology is connecting machines, operations and people around the world and how mining is moving forward."

Dec 1, 2016

By J. J. McClellenand, R. A. Jankowski

Face ventilation and water sprays are the primary controls used on continuous miner sections to protect workers from respirable coal and silica (quartz) dust. Laboratory tests were conducted by the U.S. Bureau of Mines to determine the impact on respirable dust concentrations when increasing airflow from 3000 to 9000 cfm (1.42 to 4.25 m3/sec), water flow from 15 to 35 gpm (0.057 to 0.132 m3/min) , and water pressure from 80 to 200 psi (5.52 x105 to 1.38 x106 pa). The effective limits for each control and interactions between these controls were of particular interest. Initial analysis concentrated on defining the impact of the control parameters on the respirable fraction of the feed dust, which was a blend containing 90% coal and 10% quartz. Gravimetric sampling indicated that airflow had the most significant individual impact on respirable dust levels and resulted in reductions of 99% at the operator and 57% in the return. Regression modeling was used to predict dust concentrations at the operator and in the return. Significant interactions were observed between control parameters and often, defined the level for a control parameter where increases above that level did not significantly benefit dust control. Increasing airflow to 8400 cfm (3.96 m3/sec), water flow to 25 gpm (0.095 m3/min), and water pressure to 140 psi (9.65 x105 Pa) typically provided respirable dust reductions at both sampling locations, while optimizing use of control resources. After determining these relationships for the total respirable fraction, selected filters were analyzed for quartz content to define the impact on the quartz component of the feed dust. For the individual control parameters, airflow again had the most significant impact and resulted in reductions of 98% at the operator and 26% in the return. Regression modeling of the quartz concentrations indicated that no significant interactions between control parameters were present. At the operators location, airflow was the only parameter identified as having a statistically significant reduction for quartz dust. A reduction in quartz approaching 95% was observed for increasing airflow to 6000 cfm (2.83 m3/sec). Increases above 6000 cfm had little additional impact. In the return, a linear relationship between control parameters and quartz levels was observed with reductions of approximately 27% predicted for increasing any one control parameter to its maximum level. The synergistic impact of increasing all control parameters to maximum levels resulted in a maximum predicted reduction of 81%.

Jan 1, 1991

By Joseph D. Drew

Oregon Resources Corp. (ORC) has developed and permitted a new mining operation that incorporates a process design that will allow the unique paleo-beach placer deposits of southwestern Oregon to be extracted efficiently and economically, creating the only domestically mined source of a unique foundry grade chromite and specialty de-veining sand for precision casting. The operation will also provide an additional domestic source of garnet and zircon. Engineering design has been guided by the variable geology and mineralogy of the paleo-beach placer deposits as well as the need for a dry tailing scheme that resolves a lack of water resources at the placer locations and at the same time eliminates the need for slurry settling ponds, typical of paleo-beach placer operations in North America.

Jan 1, 2010

By Clayton J. Parr, Northcutt Ely

Mining law is essentially a branch of the law of real property. It concerns acquisition of property for extracting contained minerals, and the rights, privileges and duties that fall upon the holder thereof once the rights are acquired Accordingly, this section focuses on the procedures to be followed in acquiring state. federal and private lands, and defines briefly the nature of the rights obtained. The mining laws of Canada and Mexico are summarized, and the related subjects of minerals taxation and governmental regulation are discussed briefly. This section is not intended to be the basis for legal decisions. Rather, its purpose is to provide the engineer with an understanding of basic principles and procedures. For a detailed treatise of mining law, reference can be made to The American Law o] Mining, a five-volume set edited by the Rocky Mountain Mineral Law Foundation. The law changes constantly, especially that based on federal and state statutes, and the reader is cautioned to be alert for subsequent modifications of statutes, regulations and case law. 2.1-PRELIMINARY LAND-STATUS CHECK Often, after completion of area reconnaissance, or perhaps after receipt of a submittal, a specific more localized target area will become of interest. Usually, an intensive exploration program comprising detailed surface mapping, sampling, geophysical prospecting and drilling will be required before the mineral potential of the ground can be properly evaluated. Before an investment of this magnitude is made, however, it is advisable to obtain rights to mine ore from the property. Otherwise, knowledge of the exploration activity might greatly inflate land values, or speculators or competing mining concerns might step in. Hence, as a general rule, a land-acquisition program should be undertaken before an intensive exploration project is begun. The first step in such a program is to make a land-status check to determine whether the subject lands are available and, if so, from whom they can be obtained and by what means. 2.1.1-BUREAU OF LAND MANAGEMENT RECORDS In those states which contain large areas of federal land, basically (he western states, the primary informational source is the records of the Bureau of Land Management. These may t)e examined at the land office having jurisdiction over federal lands in the area of interest. The records for Montana and North and South Dakota are kept at the Billings (Mont ) land office; Wyoming, Nebraska and Kansas, Cliejenne, Wyo.; New Mexico, Oklahoma and Texas, Santa Fe, N M ; northern Alaska, Fairbanks, and southern, Anchorage; Utah, Salt Lake City; Nevada, Reno; Arizona, Phoenix; Colorado, Denver. There are two land offices in California, at Sacramento and Los Angeles Records for other states are kept in Washington, D C. at the office of the Director, Bureau of Land Management.

Jan 1, 1973

By Gabriele Eccher, Michele Caponero, Paolo Cucino, Roberto D’Angelis

"This paper describes the optic fiber structural monitoring system implemented for Pavoncelli Bis tunnel. The paper highlights the optic fiber sensors customization capabilities, how they smoothly fit precast concrete lining processes and TBM operations, and how a lifelong service monitoring can be achieved. An overview of readings’ evolution during excavation concludes the paper.INTRODUCTIONPavoncelli Bis is a 10 km hydraulic tunnel designed to by-pass the existing Pavoncelli tunnel which experienced severe damages during the 1980 Irpino-Lucano earthquake, in south of Italy (Barla 2009). Pavoncelli Bis excavation work commenced in 1988-90, however, when excavation approached pk. 0+583 in 1992, water percolations became more and more consistent and resulted in work suspension. The tunnel was eventually sealed at pk. 0+383, leaving a flooded section between pk. 0.383 and pk. 0+583. Work resumed in 2012 where EPB-TBM excavation was adopted to cross the flooded section and to overcome complex hydro-geological conditions in various lito-types and, in particular, in the Varicolori Clay-shales area (Figure 1).Consequently, stress evolution monitoring is extremely important during construction and during the service life of tunnel lining in clay-shales and in faults areas. In particular, the paper focuses on the monitoring system proposed for the newly EPB-TBM excavated portion from pk 0+583 onwards where optic fiber sensing technology was chosen for its reading stability and reliability in presence of water and its ability to be connected in series and remotely interrogated at kilometers of distance. FBGS OPTICAL FIBER SENSOR TECHNOLOGYFiber Bragg Grating Sensors (FBGS) are gaining increasing attention in the field of experimental stress analysis. Basically, Fiber Optic Bragg Sensors are strain-measuring devices and therefore provide many of the advantages of the well-known metal foil strain gages (Kreuzer 2007).Bragg gratings are written into so called single-mode fibers. These fibers consist of a very small inner core of 4 to 9 µm diameter and an outer part (cladding) of pure glass (SiO2) of 125 µm diameter. The difference of refraction indexes between inner core and cladding causes the light to propagate only inside the small core."

Jan 1, 2016

By Gordon B. French

The Occidental Oil Shale mining and retorting system for the production of shale oil has many advantages over the conventional underground mine and surface retort systems. For example only a portion of the oil shale is mined and transported to the outside, where it blends with the existing shale talus found on most of the slopes in the immediate area. The retorted spent shale is retained underground so that it does not become a surface disposal problem. The process consumes only minor amounts of water which is produced in adequate amounts in the retorting to fulfill all mining operations needs without outside supplies. Noise and dust levels are kept to a minimum with most of the facilities located underground. The exception being the generating stations and facilities as required to monitor air and water qualities, and last but not least, more than four times as much oil is pro¬duced from a given acre than from conventional surface processing. With the increased thicknesses as available on the government monopoly area this number could be increased by a substantial amount.

Jan 1, 1975

By V. O. Tenorio

The implementation of autonomous technologies for production in surface mines demands changes in the existing monitoring and control systems. The present study deals with the concepts involved in the development of a decision support system (DSS) for the supervision of a combined fleet of manned and unmanned equipment operating in a surface mine. The project was carried out as part of an autonomous mining program that lasted from early 2006 until the end of 2008. The objective of the DSS was to achieve short-term planning goals while maintaining safe working conditions. Supervisory tasks become more complex when several autonomous vehicles operate simultaneously alongside manned equipment. The operation center where the DSS was installed allowed autonomous vehicle operations to be controlled while tracking technology reliability experiments performed on control display interfaces and interaction provided design parameters for more complex supervisory systems for autonomous mines. Mining Engineering, 2011, vol. 63, no. 11, pp. 80-86. Official publication of the Society for mining, metallurgy and exploration, Inc.

Jan 1, 2011

By C. L. Lin

The characterization of rare-earth resources in 3D is now possible using high-resolution X-ray microtomography (HRXMT) to describe ore texture and mineral phase composition. In addition, detailed texture analysis, including grain exposure and mineral association, can be described. Preliminary examination of a sample of Mountain Pass ore is reported to describe the spatial distribution of the mineral phases (calcite, barite and bastnaesite), particularly the grain size distribution of bastnaesite. The examination includes analysis of selected particle size classes to determine the appropriate size for liberation of the rare-earth mineral bastnaesite. Good liberation is expected to be achieved if the material is ground to a top size of -150 µm.

By Barrie Butt, V. S. Znamensky

The opportunity for an exploration geologist to follow a successful exploration project through the feasibility, financing, construction, development, and exploitation phase is rare. In addition, it is not often that the exploration geologist can be present during the mining of a deposit to explain why certain actions were taken or interpretations made, and to find out how these interpretations turned out in actuality. At the Woodsreef chrysotile asbestos mine in New South Wales, Australia, mining has been- in progress for seven years and the writer of this chapter has been intimately associated with the project during the five years of exploration and seven years of exploitation. The Woodsreef mine has had major production problems, the majority of which have stemmed from the unique characteristics of the ore body and fiber. Because of the latter feature, much research has been undertaken by Woods- reef and other scientific organizations in Australia, England, and Canada regarding the Woodsreef fiber. The answers to some of the problems have negated some accepted concepts of asbestos ore milling and led to the development of new techniques. Some of these new techniques include the adoption of microscopic fiber counts as a routine procedure, the modification of accepted evaluation procedures, the development of new machines for dedusting fibers, and the recognition of a fiber with a unique milling behavior pattern and, possibly, properties. The problems experienced can be broadly divided into those associated with the geology and the physical properties of the fiber. It is possible that the same features may manifest themselves in other deposits around the world, and if they can be recognized during the exploration stages, a feasiblity evaluation may be just a little closer to the actual. The Woodsreef chrysotile asbestos deposit (latitude 30°24' S, longitude 150°44' E) is located 80 km north of Tamworth, NSW, Australia. The mine has been in production for six years and has a present scheduled mining rate of 33.11 Mt/y. An eight rock line mill treats an average of 7000 t/day, after beneficiation, and yields fiber grades in the range of group 4 to group 6 with some floats. The estimated re- serves of 30.56 Mt, with an ore to waste ratio of 1:3.0, are contained in two main zones that are designated the North and South zones. Mining started in the South Zone in 1972 and then, be- cause of the higher ore value, moved to the North Zone in 1975. Presently, there are two distinct open cuts referred to as the South and North pits that will eventually be worked together. The Woodsreef mine is owned by Woodsreef Mines Ltd. and is operated by Chrysotile Corp. of Australia Pty. Ltd., and is one of only two producing asbestos mines in Australia. The second mine is at Baryulgil, (latitude 29°13' S, longitude 152°37' E), and is operated by a subsidiary of Woodsreef Mines Ltd. This operation produces about 500 t/y for a captive market. An exploration program is being conducted in the area surrounding this small producer with a significant degree of success. The concepts developed during the exploitation of the Woodsreef deposit are being incorporated in the evaluation of the Baryulgil area, and if the Baryulgil deposit proves to be eco- nomic it is hoped that this approach will eliminate some of the major crises that have beset the production at Woodsreef during the first four years of operation. The purpose of this chapter is to describe the Woodsreef deposit, and more important, to

Jan 1, 1986