Search Documents

By Klaus Rieker

North of Antwerp central train station, two single-track tunnels for the high-speed train line between Brussels and Amsterdam were constructed. At the same time, the central train station was modified to a through station. Both 1.23 km tunnels are situated in the Antwerp sands and were constructed using a slurry shield machine. Due to the inner city location, the tunnels run over their entire length underneath structures, in some cases with only minimal clearance. The paper deals with these challenging situations. In addition, the tunnel boring machine, the tunnel lining and measures to limit settlements will be introduced.

Jan 1, 2007

By Arthur M. Langer

Since the promulgation of the first Federal Asbestos Standard by the Occupational Safety and Health Administration in 1972, other federal agencies have modified the standard to better carry on their own unique missions. The instruments used to identify and measure asbestos, the sampling protocol, and the criteria used to define asbestos, have been modified to some degree. The Mine Safety and Health Administration regulates and controls asbestos dust in the mining and mineral commodity industries. However, crushed stone and processed ores contain mineral fragments that are frequently difficult to distinguish from asbestos. Mineral nomenclature, instruments for particle analysis, and sampling strategy must be accommodated to some degree to make asbestos control workable and meaningful. Precedent in other agencies has made consideration of these changes possible. Newly identified amphibole asbestos minerals have further complicated the agency?s regulatory charge. Changes in its Asbestos Standard are now being considered. Crushed taconite ore in the Eastern Mesabi highlights many of these issues. ©2008 Published by Elsevier Inc. Keywords: Amosite; Grunerite asbestos; Crocidolite; Riebeckite asbestos; Tremolite asbestos; Actinolite asbestos; Winchite asbestos; Richterite asbestos; Arfvedsonite asbestos; Fluor-edenite asbestos; Asbestos defects; Cleavage fragment; Mineral habit; Mesabi amphiboles

Jan 1, 2008

By Jr. Pitts

Elevation of surface charge density on colloidal particles in the presence of a high potential electrostatic field is demonstrated as a viable technique for preventing the accumulation of solids in solvent extraction circuits. The effect of the technique is manifest by relative turbidity measurements between pregnant leach solution and raffinate, by changes in the character of the sludge accumulations, by alteration of the zeta potential of particulates, and by a general reduction in the mass of solids.

Jan 1, 1992

By Michael E. Berndt

Asbestos first became an issue to Minnesota?s iron industry when it was revealed that mineral fibers similar to those in Reserve Mining?s tailings were being found in drinking water for several communities that used Lake Superior as their primary water source. This discovery turned what had largely been an environmental court battle into a case concerning public health. The courts listened to much conflicting and uncertain scientific testimony on the size and distribution of the mineral fibers and on the potential health effects imposed by them. In April 1974, the plant was ordered to shut down by a federal judge but the company quickly appealed the decision. The appeals court granted a stay and ultimately ruled that the plant?s closure could not be justified based on the unknown health effects of the mineral fibers since the consequences of such an action would have immediate and severe social and economic impacts. The plant was allowed to continue operation, but ordered to abate emissions to air around the plant and to switch to a land-based tailings disposal system. Much of the scientific uncertainty and public concern over mineral fibers in Minnesota?s taconite industry remain today. ©2007 Elsevier Inc. All rights reserved. Keywords: Minnesota; Iron ore; Taconite; Asbestos; Amphibole; Reserve Mining; Tailings; Mesabi Iron Range

Jan 1, 2007

By ANGELA NAIR AVELAR, Reiner Neumann, PAULO R. G. BRANDÃO

The understanding of the influence of the different types of apatite on the performance of mineral processing of igneous phosphate ores is still a challenge due to the difficulty to explain why some types of apatite floats in the froth flotation cell and others do not under the same conditions. Three types of apatite were identified by means of cathodoluminescence (CL) images in flotation concentrate and tailing samples from the Catalão mine: predominantly blue apatite, followed by green apatite and less frequently yellow apatite. The chemical composition of these types of apatite was determined by electron microprobe analysis (EPMA) and LA-ICP-MS. Blue and green apatite respond well to the process, thus remaining in the concentrate, while yellow apatite remained in the tailings. Yellow apatite is the one bearing the lowest P2O5 content and the largest anionic and cationic sites substitution, followed by green apatite, whereas blue apatite is the most homogeneous, with highest P and Ca grades and lowest substitution level. A negative correlation of the amount of phosphorus with fluorine was observed. Furthermore, impregnation of iron oxide-hydroxides in the yellow apatite was also observed. Therefore, the low flotation behaviour is due to low crystallinity coupled with impregnation onto its surface.

Jan 31, 2022

By S. Boone, J. N. Shirlaw

INTRODUCTION Soft, near normally consolidated clays generally provide ideal conditions for tunneling using Earth Pressure Balance (EPB) shields. It is easy to turn the clay into a low permeability, viscous spoil that can be pressurized to maintain the required face pres-sure. Despite this, there are records of relatively large, and often quite variable, surface settlements over EPB driven tunnels in soft clay. To understand this variation it is necessary to identify the various factors that contribute to settlement. Tunnels in soft clay are ideal for study these effects in the field, as an unsupported void will close almost immediately, due to the low shear strength of the soil. In the short term, deformation in a soft clay will occur at constant volume, so short term surface settlements can be related to movements at tunnel level. In this paper, data will be used from EPB driven tunnels in Singapore marine clay. In all of the cases discussed the lining consisted of precast concreted segmental rings erected in the tail of the shield. The marine clay in Singapore has been studied, among others, by Tanaka et al.(2001). The clay typically has a plasticity index of 40 to 60, and the undrained shear strength (SU ) can be derived from: SU = 0.22 svo' where svo' is the current vertical effective stress. Figure 1 shows a summary of undrained strength/depth plots used for design on two sections of Singapore’s North East Line. The stability of a tunnel in clay can be assessed by comparing the stability number (N) of the tunnel with the stability number at total collapse (NTC). The stability number can be calculated from the equation: N = (?Z + q – Pt)/SU where: ? = the average unit weight of the ground above the springline of the tunnel Z = the depth to the springline of the tunnel from the ground surface q = the surcharge Pt = the support pressure within the tunnel The stability number at total collapse depends on the size, geometry and depth of the tunnel, and typically ranges between 5 and 9. Charts for assessing the number at total collapse are provided in Kimura and Mair (1981), based on the testing of model tunnels in a geotechnical centrifuge. For tunnels in the Singapore marine clay, the stability number of an unsupported tunnel would be over nine if the tunnel ois more than 8m deep. As a result, a support pressure

Jan 1, 2007

By Cem Şensöğüt, Özer Ören, Yaşar Kasap

The mining sector, which has an important place in terms of raw material and energy supply, is referred as a sector with one of the highest fatal accidents in comparison with other sectors. In this century, where occupational health and safety awareness has increased, it is important to review the past accident statistics and to determine the current deficiencies by using the information in the inventory. In this study, the Malmquist total factor productivity index (MPI) has been utilized to investigate the changes in the work accidents occurring in the Western Lignite Corporation (Turkey), where underground and surface production methods are applied, and to determine the measures to be taken. According to the results obtained, both the decrease in production amount and the increase in the number of accidents caused inefficiencies during the period in concern due to the expected 10-year economic life of the mechanized system operating in the underground production panel that came to an end in 2007 and the flooding took place in early 2017. Compared with the underground operations, it has been determined that production can be carried out at the appropriate scale despite the heavy working conditions encountered due to the changing climatic conditions and the progress of production in the surface operations.

By W. R. Reed, Y. Zheng

A recent study conducted by the National Institute for Occupational Safety and Health (NIOSH) evaluated the roof bolter canopy air curtain (CAC) systemin a blowing face ventilation system, demonstrating its effectiveness and illustrating the CAC protection zones. This study evaluates the roof bolter machine CAC while operating in an exhausting face ventilation system. This study considers two similar locations to allow comparison with the previous blowing face ventilation (Zheng et al., Min Metal Explor 36(6):1115–1126, (2019)) study: (1) a roof bolter machine bolting the roof at 20 ft (6.1 m) from the face and (2) a roof bolting machine bolting at 4 ft (1.2 m) from the face. The environment introduces 6.0 mg/m3 of respirable dust to represent the roof boltingmachine operating downstreamof the continuous miner. However, the exhausting face ventilation uses an exhaust curtain with 9000 cfm (4.25 m3/s) of air. Two roof bolter machine working positions are simulated with the use of dual drill heads in the inward position for two inside bolts and in the outward position for two outside bolts. The influence of the CAC on airflows and dust dispersion is evaluated with the CAC operating at 250 cfm (0.12 m3/s) with dust reductions ranging from 39.5 to 82.8%. When the roof bolter machine operated close to the face, increasing CAC airflow was required for adequate protection since the dust reductions can be as low as 39.5%. Additional CAC airflows of 350 cfm(0.17 m3/s) and 450 cfm(0.21 m3/s) were evaluated and demonstrated that dust reductions increased to 59.7% (350 cfm) and 72.0% (450 cfm) for the worst location where the roof bolter operators located.

Aug 26, 2020

By Brendan Demich, Joseph McGuire, Emily J. Haas

Near misses recorded and reported by workers can provide awarenessto the potential causes of injury and prompt safety management initiatives. Although most companies require near-miss reporting, it is unclear what the value of these reports are, if any, and how they influence subsequent actions or controls to reduce on-the-job risks. Researchers at the National Institute for Occupational Safety and Health (NIOSH) conducted a case study with an aggregates company in which near-miss reports were analyzed at each of their locations over an entire quarter during the summer of 2018. Within that quarter, workers recorded 249 near misses. Of those, 167 were valid near misses that occurred at work. Researchers coded the reports using a qualitative 5 × 5 risk matrix. Of the 167 near misses, 19% were deemed low risk, 25% moderate risk, 30% high risk, and 26% critical risk. Several patterns in the near-miss incidents were documented, including classification of incidents and common corrective actions referenced (i.e., elimination/substitution, engineering control or redesign, work process/procedures, and personal protective equipment). The analysis provides insight into ways that risk communication and management programs can be improved to reengage workers and their situational awareness on the job.

By M. J. Gilbey

Cross passageways between adjacent tunnels in passenger rail or transit systems may be used during train fire emergencies to evacuate passengers to points of safety in the non-incident tunnel. Rescue trains can be brought into the non-incident tunnel to remove passengers to expedite evacuation times as compared to walking along bench walls to the nearest egress stairs. In cases of multiple train emergencies, the required ventilation capacities can result in high pressure differences between the incident and non-incident tunnels. These pressure differences can make it difficult or impossible for a normal person to open doors of a cross passageway between adjacent tunnels. If opened, the velocity of the airflow through an open cross passageway can reach levels high enough to impede passenger evacuation. This paper describes the analysis of this problem for a sample rail tunnel. A ventilation concept that mitigates the problems of high cross passageway door opening forces and high velocities through open cross passageways is presented.

Jan 1, 2009

By S. Acar, M. Botz

Introduction In 2007, Newmont Mining Corporation will begin construction of a milling and cyanidation leaching circuit for the Yanacocha site in Peru. Ore to be processed in the circuit contains a relatively high level of cyanide-soluble copper, and as a result, leach solutions are expected to contain elevated levels of copper and WAD cyanide. As the means of controlling copper levels in leach solution, a circuit will be installed to precipitate copper sulfide from barren solution using sodium hydrosulfide. In addition, a circuit will be installed to recover cyanide from barren solution, with recovered cyanide to be returned to the leaching circuit and treated solution to be utilized as make-up in existing heap leaching facilities. As needed to support design of the copper precipitation and cyanide recovery circuits, pilot testing was conducted in 2005 to determine preferred operating conditions and evaluate the performance of the processes. This paper presents results from the pilot testing where 99% copper reduction was achieved and 95% to 98% cyanide recovery was achieved.

Jan 1, 2007

By Steve Kral

Reducing the cost per ton and increasing productivity are key factors in a mine’s profitability. Mining companies can do little about commodity prices. So to keep a mine operating at a profit, management must reduce costs and improve worker and equipment productivity in every facet of a mining operation. From mining to crushing to processing, mine management is constantly seeking new methods and technologies to improve the way it mines minerals. And it is willing to borrow techniques used by other operators.

Jan 1, 2002

By Xuehua Zhang, Shengxiong Yang, Huiqiang Yao, Gaowen He

"Seamount cobalt-rich ferromanganese crusts (hereafter crusts) are authigenic iron/manganese hydroxide/oxide deposits formed from direct precipitation of minerals from seawater onto a hard substrates surface. Crusts contain significant concentrations of cobalt, manganese, nickel, copper, platinum, rare earth elements and other valuable metallic elements, with potential economic value. Regulations on Prospecting and Exploration for Cobalt-rich Ferromanganese Crusts in the "Area" was approved by the Council and Assembly of the International Seabed Authority in July 2012, China and Japan became the first to obtain exploration contracts, which were signed respectively in April and January 2014.The crusts form pavements and are mainly attached tightly to the surface of the substrate, and less commonly crusts coat talus debris located on the surface of sediment and substrate rock. During prospecting, crust sampling methods mainly include dredge, TVgrab and sub-bottom coring system. During exploration, the sub-bottom coring will be the dominant method for crust sampling, and if necessary, ROV sampling will be used. Usually the samples collected by different methods provide a larger quantity than samples needed for chemical analysis, but sampling quantity is a question that should be considered for mineral resource evaluation that how to ensure that the sampling is representation for the sampling station. Using the samples collected by China from Pacific seamounts, according to the designed analysis flow and Qeqott formula (Q=Kd2), the minimum reliable assay sample quantity ("MRASQ") of crusts for Mn, Co, and Ni are obtained. In the case of the sample homogeneous fines at ~100 mesh size (~0.15 mm), MRASQ for Mn, Co, Ni is respectively 4.5 g, 9 g and 9 g. This result provides the basic data for crusts resources evaluation."

Sep 1, 2014

By H. Lyn Bourne

This is the fifth annual tabulation of mineral royalty information. This tabulation, like the previous editions, includes all of the earlier data. There are also 60 new entries. In addition to royalty information, some entries show the cost of purchased reserves. Two articles relative to the evaluation of minerals reserves appeared in December, 1986. R.H. Paschall (In the Aggregate, ME, p 1139) wrote a good article, although it lacked specific royalty data. However, this author takes exception to two ideas in Paschall's column. Paschall contends that the royalty rate does not affect the mineral appraisal. This present author could not disagree more. Paschall also claims the location of an industrial mineral deposit is the only serious or practical caveat in comparing royalties. Comments received here from readers helped make the list of caveats that are cited each year. The readers will decide which factors influence the mineral value for their commodities of interest. Paschall's point about the relationship of the parties who are negotiating a royalty agreement is important and very well taken. The other article, written by William Vernon (Pit and Quarry, December 1986), gives a step-by-step process on how to conduct a mineral appraisal. The article cites three reasons for an appraisal: transfer rights; collateral for a loan; and taxation. A fourth reason is to establish adequate compensation for reserves lost through condemnation. This author has appeared in several court cases where compensation for loss of mineral reserves through condemnation required a mineral appraisal. Royalty rate becomes an important factor in the appraisal process, although the Pit and Quarry article refers to that part of the valuation equation as "profitability." Both articles were well written and are recommended reading for those interested in mineral valuations. The same caveats that have appeared in previous columns relative to factors that influence the value of reserves are restated. The data in the table serve as a general reference and are not intended to present an absolute scale of reserves costs. Several factors influence the value of any mineral commodity. The factors include: • location/transportation - especially significant for most industrial minerals; • market conditions both for the commodity and the company acquiring the right to mine; • quality or grade of the deposit as it reflects the amount of processing/beneficiation necessary to produce the finished product; and • legislative restrictions and conditions for mining a given material at a given site. These and other factors will significantly influence the cost of reserves. The table shows the range of royalties and the variations in the basis of computing the fees. In a few instances, it gives the cost of acquired reserves based on purchase price and quantitative estimates of the material in place. The table lists the commodity in column 1, and the subsequent columns give: • the location by state, US geographic area, or Canadian province ; • the cost - R for royalty and P for purchased cost; • the year in which the lease or purchase agreement occurred; and • comments or footnotes for more information. The cost column requires more explanation. The units may refer to cubic yards (/cu yd), cubic feet (/cu ft), short tons (/T), or acres (/A). 1 cu yd = 0.76 M2 1cuft = 0.28m3 1 st = 0.9072 t 1 acre - 0.4047 ha or m2

Jan 7, 1987

By Richard S. Della Valle

Sandstone and shale samples from the Morrison (Late Jurassic) and Dakota formations (Cretaceous) from northwestern New Mexico have been analyzed for the major elements Na, K, Fe and the trace elements Sc, Cr, Co, Rb, Sb, Cs, Ba, Hf, Ta, Th, iJ and the rare earth elements (REE) in whole rock and clay sized fractions by instrumental and delayed neutron activation analysis. The clay sized fraction clearly shows enrichment patterns and halo effects ; whereas, the whole rock fraction does not. Important elemental dispersion halos associated with uranium in sedimentary environments include the REE, Hf, and Sb. The distribution of these halos are due to a combination of complexation, chelation and the orignal paleoenvironments.

Jan 1, 1984

By Jon Y. Kaneshiro, Ed Walton, Stephen J. Navin, Robert M. Sergeant, Storer J. Boone

The Coronado Traffic Tunnel is a proposed two-lane, reversible, road tunnel, which will relieve severe peak hour congestion problems on surface streets. The tunnel will take traffic from the Coronado Bay Bridge to Naval Air Station North Island. The project will include 12.5 m (41 ft) inside diameter by 1,112 m (3,650 ft) of tunnel, 552 m(1,815 ft) of cut and cover box structure, and 400 m (1,315 ft) of open cut structure. The geology consists of predominately clean and silty sand, saturated sand, with some clay layers, requiring Earth Pressure Balance or Slurry Shield tunneling technology.

Jan 1, 2001

By Tom Michaud, Rob Albinger, Ian Turner, Michael Rispin

Data transmission, communication, tracking, and the connection of equipment such as gas detectors, cameras, and collision avoidance systems in today's tunnel industry are critical pieces of the constructor's infrastructure. Reliability, flexibility, redundancy, and cost-effectiveness are key in selecting and implementing inte- grated systems. Both wired and wireless components are used to deliver custom solutions and can involve interconnectivity between backbones. Systems integration is important as industry adopts proven technologies from other industries. Case stud- ies are given showing how tailor-made approaches deliver needed functionality, with varying degrees of com- plexity, in various classifications of environment, in order to meet a project need.

Jun 23, 2024

By Shosei Ph. D Serata

The Stress Control Method of mine design provides enhanced engineering control over the behavior of underground structures in comparison to conventional mine design methods. The same Method can be applied to achieve design control of surface subsidence. The basic mechanism relating undergroued deformation and surface subsidence is disclosed by mine simulations, using the REM (Rheological Element Method) computer code, whose predictions have been validated by field measurements. The key components of the underlying mechanism of surface subsidence have been shown to be the stress envelopes formed in the process of underground excavation. It has also been demonstrated that significant control of surface subsidence can be achieved by designing the geometry and timing of underground excavation to regulate the formation of stress envelopes. A field example is given in this paper to illustrate this application of the Stress Control Method.

Jan 1, 1986

By Steve Stuart

Deep-sea mineral SMS deposits present some of the world’s most challenging conditions for drilling equipment. As robotic seabed drilling services mature so too the ways that clients engage with service providers to maximise their data requirements. This presentation reviews key considerations for planning and executing a successful seabeddrilling program in variable mineralised deposits. Some of the means of collaboration between robotic seabed drilling contractors and those hiring their services are explored; where improved efficiencies and recoveries over the period of a drilling programme could be achieved. Potentially new technology or methodology can be looked at to further improve these approaches.

Sep 1, 2014

? The economic health and national security of the U.S. depends on the continued availability of, and access to, reliable and affordable energy and mineral resources. However, America is hindered by a costly, inefficient and often redundant regulatory structure that thwarts domestic investment, expansion and job creation. The annual cost of federal regulations in the U.S. increased to more than $1.75 trillion in 2008; averaging $8000 per employee.(The Impact of Regulatory Costs on Small Finns, SBA, 2010) ? The complexity, uncertainty and delays within the current permitting system places the U.S. at a competitive disadvantage with many other countries that have both abundant mineral resources and a more welcoming business and regulatory climate. As a result, American and international mining companies often move overseas or across borders to invest capital, create local employment, and produce the critical minerals America must then import at higher cost, while sacrificing employment and economic stimulus. ? According to Behre Dolbear, the U.S. is ranked lowest globally due to the lengthy permitting period required before mine development can commence. (Where not to Invest, 2010).

Jan 1, 2011