Search Documents

By D. C. Martin

Stability analysis and design of open pit slopes is generally based on an assessment of rock cores and rock exposures on surface or in underground workings. Until recently, core for such assessments has been readily available from exploration drilling programs. In recent years, many exploration programs have reduced the amount of coring and rely more heavily on less expensive rotary or percussion drilling programs where drill cut-tings are sampled for geological evaluation and assay. This paper describes a technique whereby costs of the geotechnical investigation are reduced by using rotary percussion drilling information to assess geotechnical properties of the rock mass. A limited number of core holes are required to establish basic relationships between the mechanical properties of core and the characteristics of the percussion chips. These properties are used as a basis to extrapolate the coring information to encompass the entire area of the rock mass for which percussion drilling information is available.

Jan 1, 1990

By B. Stewart

Recent ore pass failures have underlined the need for improved designs, standards, structural monitoring methods, and better hang up prevention and removal techniques. Researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) are investigating methods to improve safety during transport of ore in ore passes. Design criteria and hang-up prevention and remediation strategies involve studies of the effects of static and dynamic ore and waste rock loads on chutes, walls, gates, and support structures. Particle flow analysis methods were used to simulate the response of various ore pass designs to a wide range of ore loading conditions. A full-scale mock-up of actual ore pass and chute assemblies was duplicated and tested for load response. Data from a particle flow code and the mock-ups were com-pared. Loads on an active ore pass chute were measured.

Jan 1, 1998

By N. K. Bohidar

Evaluation of the stability of a structure under given boundary conditions requires accurate knowledge of the state of stress as well as the mechanism of failure at the critical state of stress. This paper represents a part of the research done by N. K. Bohidar during 1965-1968 for his Ph. D. research in Mining Engineering at the University of Utah. It summarizes the determination of internal stress and failure phenomena around cylindrical openings in viscoelastic media subjected to lateral restraint and vertical uniaxial load. The conditions of lateral restraint and viscoelastic nature of the media represent conditions associated with subsurface openings in rocks. The financial assistance provided to the project from the University of Utah Research (Uniform School Fund), W. C. Browning Scholarship Fund, Earth Science Research Fund, and D. C. Jackling Loan and Scholarship Fund is gratefully acknowledged. The authors also acknowledge the assistance of S. Siugh, W. Jones, and K. McCarter during the project.

Jan 1, 1970

By B. Waterman, D. Ramey, L. Schlink

"Water is a primary commodity for most industrial processes. It has become a global focus in light of climate change and population growth. Reuse of process water has two major benefits - minimize the amount of fresh water added now and minimize the amount of discharge water that requires treatment later.Mining and mine product processing has its share of reused water. For example, reclaim water from a tailings impoundment, overflow from thickeners and leach solution to raffinate and back again all demonstrate the use and reuse of water in mining circuits. Eventually, a mine reduces production or ceases operations completely, eliminating the option to reuse the impacted water and, thus, requires treatment of the remaining water.Current methods of water treatment remove the impacts, providing clean water for discharge, but leaves behind a concentrated waste that requires further treatment or disposal of a hazardous waste. Freeport- McMoRan is currently testing three water treatment technologies specific for sulfate and/or metal removal from mine impacted water with the approach of transformation not concentration. These technologies provide clean water for alternative use while creating byproducts that could be marketable, or disposed as a nonhazardous material, thereby reducing the cost and longterm liability of disposal.The selection of a water treatment process is site-specific. The volume of water, contaminant to be removed, disposal options, length of time for treatment, location of plant and reagents and discharge requirements are some of the factors that need to be considered when selecting a water treatment process. Common water treatment technologies for mine impacted water consist of low- or high-density sludge (LDS/ HDS), reverse osmosis (RO) and evaporative technologies. In addition to operating costs, these processes require additional handling of the concentrated sludge or brine. Advanced water treatment technologies include ion exchange, solvent extraction and metals precipitation with or without the aid of a biological system. Some of the more complex systems have a series of unit operations to achieve required discharge regulations."

Jan 1, 2014

By Chris McKee

Quartz has been of interest in occupational health for years because it can cause silicosis after prolonged exposure. New OSHA regulations (Air Contaminant; Final Rule) list perlite as a nuisance dust. They conclude that perlite is nontoxic when air-borne total particulate concentrations are 15 mg/m3 or below and when quartz content is less than 1% crystalline silica. OSHA has established an 8-hour PEL of 15 mg/m TWA for total perlite dust containing less than 1% quartz. OSHA has established a 5 mg/m3 TWA PEL for respirable perlite. These limits will protect workers from significant risk of eye, skin, or other physical irritation. This regulation is based on a Group 2A classification as a probable carcinogen in humans, at the 0.1% crystalline silica level, by the International Agency for Research on Cancer (IARC 1987a, b). IARC found sufficient evidence for carcinogenicity of crystalline silica in animals and limited evidence in humans. Perlite is not listed as a carcinogen by OSHA or the National Toxicology Program.

Jan 1, 1990

By Gary G. Grim

The reliable performance of the coal reclaim system is essential to the continued availability of a coal-fired electric generating unit. The control of fugitive coal dust within the areas housing the reclaiming equipment is necessary not only to minimize maintenance and clean-up costs, but is also a safety and health consideration. This paper describes the reclaim system control and dust suppression systems as initially installed, the shortcomings of these systems and the steps eventually taken to correct these shortcomings.

Jan 1, 1983

By K. V. K. Prasad

Stochastic simulation has been routinely used for performing risk and sensitivity analyses in a variety of fields. The commonly used means of generating the simulations has been the Monte Carlo approach which usually employs a Simple Random Sampling (SRS) scheme of the variable distributions. This method is prone to sample clustering and requires a large number of samples to represent the distribution faith-fully. This can become problematic for simulating complex processes where it is impossible to run an arbitrarily large number of replicate simulations. The Latin Hypercube Sampling (LHS) method uses a stratified sampling approach which assures representation of the input distributions for any given number of samples. In this paper the LHS and SRS approaches are compared using a petroleum resource estimation example.

Jan 1, 1993

By Bo Hyun Kim, Mark K. Larson

Researchers at the National Institute for Occupational Safety and Health have tested the finite element code, UT3PC, with LaModel to evaluate their results using know case studies. The purpose of the testing was to demonstrate the usefulness and limitations of these programs in evaluating mine layout design. Both of these software packages are simple to use and free for public download. Their use by mine engineers, along with other tools, such as empirical methods, can enhance the assessment of a mine layout design. LaModel can model mining layout on a mine scale or, at least, on a multiple-panel scale. However, this software has limitations in calibrating to conditions at many coal mines in the western United States. The UT3PC software models smaller parts of a mine and is used to evaluate the design of pillars, shafts, or drifts; but the software calculates all components of the stress tensor and provides stresses, displacements, and safety factors throughout the model volume. The two codes are used to evaluate design of one known case, and UT3PC is used to evaluate another case. The results and approaches demonstrated in the testing are intended to aid mine engineers in evaluating site-specific problems and to show that these tools can provide useful information to the mine engineer in evaluating mine layout design.

Jul 1, 2023

By B. Ladanyi

An adequate knowledge of the overall behavior of a rock mass at a given site is fundamental to the satisfactory design of a rock slope. The be- havior is controlled by a variety of factors, in- cluding rock type, geological structure, stress and ground water conditions. There are essentially three lines of approach that may be used to obtain information on the in-situ rock mass behavior for the purpose of the design of a rock slope: (1) Direct measurements of rock mass properties by means ol laboratory and field tests. (2) Evaluation of rock mass properties from a study of slope failure case histories and sta- tistical information on stable and unstable natural rock slopes. (3) Evaluation of in-situ behavior of rock mass by using a physical or mathematical model technique.

Jan 1, 1980

By Peter C. Finlayson

Rapidly rising gas and oil prices and the falling quality of coal is forcing energy users in many parts of the world to consider the application of low grade fuel, particularly coal, for steam raising and power generation. However, the use of such low grade coal is normally resisted by the consumer because of operational problems associated with high ash content, sulfur emission and, in some instances, slagging problems caused by low melting temperature constituents in the ash. Recently developed technology involving 'fluidized bed combustion' offers a potential solution to these operational problems. Much of the early work was conducted in Britain, where rig tests were commenced during the early 1960's. This has led on to the successful conversion and operation of a fluidized bed fired industrial boiler at the Renfrew works of Babcock & Wilcox Ltd. Orders for the first commercial boilers incorporating this technology have recently been announced. Significant development work on fluidized combustion is now being undertaken in various parts of the world, in particular North America, Germany and Japan, and the first large scale units are under construction or being commissioned. This paper concentrates on the development of the technology in Britain, outlines the reasons for applying fluidized bed combustion and de-scribes its application at atmospheric pressure for steam raising and at elevated pressure for power generation . Coal Processing Consultants is a Partnership between the National Coal Board and Babcock & Wilcox Ltd. of Britain and has been established in order to provide technical advice and economic evaluations on all aspects of coal processing and utilization. In view of the involvement of its Parents in the development and exploitation of fluidized bed combustion technology, Coal Processing Consultants has been retained by clients in various parts of the world to provide expert advice on the application of fluidized combustion for particular coals and project situations.

Jan 1, 1978

By Dennis C. Martin

Construction of the Cerro Colorado on-off leach pad in northern Chile required about 3 Mm2 (32.3 million sq ft) of fill over an area of about 600,000 m2 (6.5 million sq ft) in irregular terrain with relief of up to 40 m (130 ft). Earthwork construction was completed in about six months using mine waste, placed in 4 to 6 m (13 to 20 ft) lifts with mine haul trucks. The lift thickness was reduced and the compactive effort increased in the upper 10 m (33 ft). This was done to develop a mat for additional resistance to possible differential settlements due to the modest density of the fill and dynamic (earthquake) conditions. A single 2-mm (80-mil) high-density polyethylene (HDPE) liner was used below the leach pads. This was protected from the loading and unloading equipment by bedding and cover systems. It consisted of screened sand, gravel and silt as the bedding and cover layers and a heel of screened gravel and primary crushed low-grade ore.

Jan 1, 1995

By D. H. Carlson, J. H. Johnson, C. F. Renders

Introduction Diesel-powered vehicles are used extensively in underground mines throughout North America. The bulk of the diesel vehicles found in underground mining operations are used for loading and ore haulage, as well as for transportation of personnel and supplies. Along with the advantages of using diesels underground is the disadvantage associated with diesel-tailpipe particulate-matter emissions (DPM). The concentration of DPM in the ambient air of US underground metal mines is not now regulated by the Federal Mine Safety and Health Administration (MSHA). However, recent studies have shown DPM to be mutagenic (National Institute of Occupational Safety and Health, 1988), and the American Conference of Governmental Industrial Hygienists (ACGIH) has recommended that the exposures of per¬sonnel to DPM be limited to an 8-hr time-weighted average concentration (threshold limit value or TLV) of 0.15 mg/m3 (Anon., 1995). The authors, while making measurements in a number of US underground mines that use diesel haulage equipment, found mine air DPM concentrations ranging from 0.2 to 2.36 Mg/M3 (McCawley and Cocalis, 1986; Watts et al., 1989; Cantrell et al., 1991; Haney, 1992; US Bureau of Mines, 1992; Watts, 1992; Watts et al., 1995). If the proposed DPM TLV were to be adopted as a permissible exposure limit (PEL) for US underground mines, the proposed limit of 0.15 mg/m3 PEL would be lower than any of the concentrations measured in the earlier studies and would represent more than a 15-fold reduction from the maximum 2.36 mg/m3 concentration. A 0.15 mg/m3 PEL would also represent a 4.5-fold reduction from the average 0.68 mg/m3 measured mine ambient air DPM concentration reported in this paper. Other diesel tailpipe emissions that are now regulated underground include carbon monoxide (CO), with a PEL of 50 ppm; nitrogen dioxide (NO,), with a PEL of 5 ppm; nitric oxide (NO), with a PEL of 25 ppm; and sulfur dioxide (SO,) with a PEL of 5 ppm. Because the concentrations of these gaseous pollutants and DPM are affected by the state-of-maintenance (Waytulonis,1992), it is important that a means be developed to measure emissions from engines that are now in service to determine when maintenance is needed. The current study was the result of an inquiry by mine¬maintenance personnel who had been receiving complaints about high concentrations of diesel soot (DPM) in mine headings from load-haul-dump (LHD) vehicle operators. Mine-maintenance personnel were searching for an objective test to determine if the diesel tailpipe particulate emitted was excessive. The mine was also evaluating electronically controlled, two-cycle, naturally aspirated, direct-injection diesel engines on some of their JCI (John-Clark Inc.) load-haul-dump (LHD) vehicles. These LHD vehicles were used to haul freshly blasted ore from mine headings to a feeder breaker. The feeder breaker breaks down the larger chunks and feeds the broken ore onto a conveyor. Michigan Technological University, in past studies, developed an emissions-measurement apparatus (EMA) ca¬pable of measuring diesel vehicle tailpipe pollutant concentrations (Chan et al., 1992; Chan et al., 1993; Carlson et al., 1994). At the time of the study reported here, most of the mine's LHD vehicles used a 12-cylinder, four-cycle, naturally aspirated prechamber diesel engine. The study was undertaken in cooperation with mine maintenance supervisors from late 1992 through July 1993. The objectives were to compare diesel exhaust emissions between the 6-cylinder, two-cycle, electronically controlled, direct-injected diesel engine and the 12-cylinder, four-cycle, prechamber diesel engine and to, then, use the data collected, in conjunction with mine ambient air measurements, to demonstrate the application of the "deterioration factor" (Chan et al., 1992), which is a measure of the state-of-maintenance of mine-vehicle engines that are now in service. The information would be used to identify vehicles that need maintenance to reduce emissions. The data reported here are unique in the sense that they combine underground diesel vehicle ambient and tailpipe

Jan 1, 1999

By Toshio Fujiwara, Sumikichi Ito, Masao Kitamura

The Tennohji-Benten Giant Trunk Sewer Project has been under construction since 1974 in the eastern part of Osaka, the second largest city in Japan. The entire project is divided into 7 blocks, some of which have already been completed. This 8.8-km sewer tunnel, being driven through a densely populated area, was planned to be constructed by the shield tunneling method. This paper described shield tunneling performances and ground behaviors during the construction of Blocks 2 and 3. An earth pressure shield (dia., 6,750 mm) was employed in Block 3 tunneling. The ground was generally soft and the cover over the tunnel varied from 13 m to only 4.5 m, so that a considerable amount of chemicals was injected to stabilize the ground. A hand-digging type shield (dia., 7,250 mm) was used in Block 2 tunneling under compressed air. For 85 m of the total length of 1.6 km, the soil at the face was extremely soft, and therefore, the ground freezing method was additionally employed.

Jan 1, 1981

By Thomas N. Walthier

This paper will review world trends that are increasingly restrictive of mineral exploration and mining throughout the Free World This is occurring in the face of projected huge increases in demand for mineral products Some of the impediments are direct and absolute; others are indirect, but nevertheless effective; still others represent merely hostile attitudes Many of the world governments have a reputation for lack of integrity in dealing with existing foreign investments within their borders, and consequently are quite uninviting places for new investments, especially in the capital intensive natural resources industry. Compared with even 35 odd years ago (and pre-World War II is not that long ago) there are few places left where private mining investments are both wanted and where investors are willing, to go. We shall begin with an analysis of conditions in the U. S., shift to neighboring Canada and Flexico, and then have a look around the world. As the world grows smaller for the private mining sector, the function of exploration, development, and operation is passing over to government. We'll conclude with a view of what this holds for the future

Jan 1, 1976

By Babcock. C. O.

This report presents equations derived from experimental testing to convert borehole pressure cell data from vertical and horizontal cells to the biaxial ground stress changes. While hydraulic pressure cells in boreholes have been in extensive use since 1957, methods of data reduction have been slow to develop. The methods of Sellers (1970) and Bauer et al. (1985), respectively, indicate a linear relationship between cell pressure change and the rock stress change. Lu presented a theory for creep behavior (Babcock et al., 1982). In the present work, in laboratory testing, the logarithm of the cell pressure was related to the stress change in seven elastic materials for a range of Young's moduli of 3.45 to 85.5 GPa (0.5 to 12.4 x 106 psi). The gage response depends upon the setting pressure of the gage, the gage pressure at any time, the rock properties, and the cross-sensitivity of the gage to transverse loading. The setting pressure of the cell should be proportional to the Young's modulus of the rock, the absolute stress can be determined by overcoring in strong rock, and the in situ Poisson's ratio can be estimated in some cases from the cell responses.

Jan 1, 1986

By H. Wesley Peirce

Although not generally recognized, Arizona has rock salt deposits unique in the United States. This uniqueness stems from a combination of two factors: (1) relatively youthful geologic age and (2) nonmarine origin. Although Arizona shares one deposit with Nevada (Figure 1, No. I) there are three others within the State (Nos. 2, 4, 5) that are believed to be both late Cenozoic in age (less than 15 million years) and nonmarine in origin. The only other recognized nonmarine salt deposits in the U.S. are much older, being in the early Cenozoic (Eocene) Green River Formation of Colorado and Wyoming. According to Johnson and Gonzales (1), the remaining rock salt deposits in the United States are marine and either Paleozoic or Mesozoic in age. Of the seven localities shown in Figure 1, six in the Basin and Range geologic province are believed to represent nomarine late Cenozoic phenomena and one (No. 7) in the Colorado Plateau geologic province is Paleozoic (Permian) in age and marine in origin. The following comments are intended to update the general geologic highlights of these deposits and to summarize the nature of their present utilization.

Jan 1, 1979

By W. Dan Hausel

In previous reports by Hausel et. al., (1979 a, b, and c), Leighton and McCallum (1979), and McCallum (1974;1979), several exploration procedures were examined as to their effectiveness in locating kimberlite intrusives in northern Colorado and southeastern Wyoming, where approximately 90 kimberlites have been recognized within 5 districts (Figure I). Briefly, geological mapping and stream sediment sampling for indic- ative heavy minerals of kimberlite (pyrope garnet, chrome diopside, and magnesian ilmenite) proved to be the two most effective methods in isolating kimberlite occurrences within the granitic terrain of Colorado and Wyoming (Hausel et. al., 1979 a, b, and c; Leighton and McCallum, 1979). Where a kimberlite intrusive is deeply weathered, remote sensing using color and color infrared aerial photography may be a potential reconnaissance tool in kimberlite exploration. The kimberlitic eluvium supports thicker grassy vegetation, and at least one species of grass (the Bluebunch Wheatgrass) is found to grow only within the eluvium. The result is that vegetation in the kimberlitic eluvium is a better infrared reflector than the vegetation in the surrounding granitic soils (Hausel et. al., 1979 b; McCallum, 1974

Jan 1, 1980

By S. G. Hardcastle, C. K. Kocsis

Ventilation is an expensive prerequisite for underground mining. Current mining trends, including increasing depth and mechanization and more stringent health regulations would generally dictate that more air volume is required in order to provide good working conditions underground. However, any increase in the mine’s intake airflow can produce a disproportionate increase in power consumption and hence operating costs due to the cubic relationship between the sup-plied air power and the airflow (Power a Flow3). Furthermore, forecasts of significant increase in energy prices and new commitments with regard to reductions of greenhouse gas(GHG) emissions, determined the mining industry to look into developing new concepts, design tools and incorporate the latest mining technologies in order to lower capital and operating costs while meeting commitments regarding GHG emissions. The advances in computing power and modelling software now make it possible to design, model and schedule a mine from opening to closure. A developing trend is to design and plan the mine by means of orebody modelling software, followed by using discrete-event simulation techniques to predict production rates and evaluate various operating scenarios throughout the life of the mine. The authors are currently evaluating how such process simulators could be adapted in order to forecast the need for materials or a specific resource, and one of these would be the mine’s “life-cycle” airflow demand as a function of scheduled production rates and mine operating characteristics. Further to this, based upon the mine’s life-cycle airflow demand schedule, the ventilation system could then be designed using a mine ventilation simulator. This new design approach would integrate in parallel the development of the ventilation system with the current mining conditions, therefore, heading towards “develop-as-you-go” as opposed to developing the system for final requirements with high upfront costs. This new ventilation system design criteria would also incorporate the use of the “ventilation-on-demand” technology, which will further lower development and production costs and implicitly, the mines’ GHG emissions.

Jan 1, 2004

By S. K. Sahoo, S. K. Sharma, A. Yadav, B. Behera, G. S. P. Singh

A field representative modeling of the gob behavior is critical for the understanding of the associated mechanics of strata behavior in longwall workings. The findings of theoretical models and laboratory tests on the simulated gob material have shown the strain hardening behavior of the gob material. The double-yield material model, which is a built-in constitutive model in FLAC3D, has significant potential to simulate the gob compaction process as it represents materials which undergo irreversible compaction in addition to shear yielding. Apart from this, several researchers have attempted using modified elastic model or applied nodal force in reaction to the strain in the gob area as per the well-known theoretical relations to meet this requirement. Although these models can simulate the mechanical response of the gob for subcritical and critical extraction widths, they do not apply to supercritical extraction width as the gob stress may exceed the in situ stress level in such cases. For overcoming these limitations, a standard approach has been developed and validated in this paper, which can be used for simulating the gob behavior in supercritical longwall workings as well. The complete study is divided into two stages wherein the laboratory scale compression test on the simulated gob material has been numerically replicated to develop preliminary confidence followed by a parametric study of the double-yield constitutive parameters for a rational estimation of their values in different conditions. The calibrated model has been used for verifying its results by plane strain modeling of two different longwall workings, using well-established empirical and analytical findings and field observations. The approach suggested in this study can be used for the efficient modeling of the gob behavior of longwall panels under varying geo-mining conditions without compromising the accuracy of the numerical model. The meticulously validated model can be helpful in rational estimation of stress redistributions around the gob area apart from load transfer on the barrier pillar.

By M. Stephen Enders

The Little Rocky Mountains host epithermal gold-silver bearing vein and stockwork deposits in a syenite intrusive complex. Pegasus Gold Ltd. is currently mining the oxidized deposits by open-pit methods and recovering gold and silver by heap-leach processes. A geologic program has been designed to effectively determine the basic ore characteristics; 1)mineralization; 2)oxidation; 3)structural setting; 4)lithology; 5)alteration; and ultimately, 6)the leachability of the ore. Geologic mapping, sampling, drilling, assaying, and testing are routinely used in exploration, development, production control, mine planning, and ore reserve estimations. Timely and accurate assay results are essential for the program's success.

Jan 1, 1983