Search Documents

By D. R. Wilburn

This summary of international mineral exploration activities for 2012 draws upon information from industry sources, published literature and U.S. Geological Survey (USGS) specialists. The summary provides data on exploration budgets by region and mineral commodity, identifies significant mineral discoveries and areas of mineral exploration, discusses government programs affecting the mineral exploration industry and presents analyses of exploration activities performed by the mineral industry. Three sources of information are reported and analyzed in this annual review of international exploration for 2012: 1) budgetary statistics expressed in U.S. nominal dollars provided by SNL Metals Economics Group (MEG) of Halifax, Nova Scotia; 2) regional and site-specific exploration activities that took place in 2012 as compiled by the USGS and 3) regional events including economic, social and political conditions that affected exploration activities, which were derived from published sources and unpublished discussions with USGS and industry specialists.

May 1, 2013

By J. D. Morgan

The US economy grew steadily in 1989, reaching an annual rate of $5.3 trillion in the last quarter (US trillion=1012 ). The value of domestically processed, mineral-based materials rose 5% to $315 billion (US billion=109). The value of metals produced from US ores rose 14% to $11.6 billion, while industrial minerals rose 2% to $20.2 billion. Recycled scrap was valued at $10 billion. Increasing economic activity stimulated metal prices. Yearly lows and highs were $2.31 and $3.56/kg ($1.05 and $1.62 per lb) for copper, $1.58 and $2.57/kg (72 and $1.17 per lb) for aluminum, 77 and 97 cents/kg (35 cents and 44 cents per lb) for lead, and $1.58 and $2.09/kg (72 cents and 95 cents per lb) for zinc. Many mining and metal companies reported reasonable profits. Consumer demand strongly affects mining because the US economy is saturated with long-lived products. Consumer, mortgage, and Federal debt continued to rise. 250 million US citizens already possess 172 million licensed motor vehicles and 100 million dwelling units. New car production fell 4% to 6.8 million units, while truck and bus production fell 1 % to four million units. New housing starts fell 9% to 1.4 million units. Imports supplied a significant proportion of total US consumption of several important mineral materials. Imports of crude and refined petroleum costing $50 billion exceeded domestic crude oil production. President Bush expressed "strong concerns about this country becoming further dependent on foreign oil." And the Department of Energy held a series of hearings around the country to develop ideas for a "national energy strategy."

Jan 1, 1990

By H. Savasci, G. Yarim, J. S. Chung

As part of ongoing deep-ocean mining research, hydraulic transport systems as well as status of deep-ocean mining systems are reviewed in the aspects of manganese nodules and crusts from 8006,000-m depth. The emphasis of the investigation of hydraulic transport is placed on the shape effect of particles on the pressure gradients and flowrates. Series of tests are being conducted to study the lift characteristics of a 2-phasevertically upward hydraulic transport of 2 types of small solid particles in a PVC pipe of 1-in (2.54 cm) diameter: irregular-shaped silica sands and equivalent spherical glass beads. Pressure drops and mass as well asvolumetric flow rates were measured by electromagnetic(EM) flowmeter and mass flowmeter. The particle sizes used are 8-10 mesh. The results in turbulent flow range of 101045Re show that pressure gradients or friction factors are smaller for the spherical beads than the sands. The larger the concentration of the particles are, the larger the pressure gradients become. The larger the particle concentration is, the less the effect of particle shape on pressure gradients becomes. The shape effect is greater for the minimum particle transport velocities than for the settling velocities.

Jan 1, 1999

By Philip D. Lindahl

The US Bureau of Mines (USBM) began research to improve the safety and efficiency of transporting coal from underground coal mines using a balanced air-lift hydrohoist (ALH). ALH includes a U-tube pipeline that can be installed through an existing shaft or two surface-drilled holes connecting the mine level to the surface. Bench- and pilot-scale models were tested to evaluate the feasibility of hydraulically hoisting a coal-water slurry in a riser pipe by injecting compressed air microbubbles. A prototype injector was developed that continuously compacted -50-mm (2-in.), run-of-mine coal in a screw feeder and injected a thick coal slurry into ALH. Initial production rates of 40 t/h (44 stph) through a 200-mm-(8-in.-) diam riser pipeline were achieved with a50-m- (165-ft-) high pilot-scale model. The potential productivity was expected to increase to 100 t/h (110 stph) through modification of the coal injector.

Jan 1, 1995

By B. Oraee

Tunnels as any other structures are affected by different loads and stresses. Generally, the loads on tunnels consist of both static and dynamic loads. These loads must both be considered in the tunnel design process. In this paper, the stability state of Jiroft water-transform tunnel is evaluated. Firstly, the in-situ stresses and then using Kirsch?s equations the induced stresses due to static loads in walls and crown of tunnel are calculated. Consequently, the strain caused by probable earthquake without considering the interaction between the concrete lining of tunnel and rock mass using seismic analysis is calculated based on free-field deformation. When the strain is determined, the simplified method of closed-form solution, Wang?s equations and Penzien?s equations are used to estimate the applied forces on the tunnel due to earthquake such as axial force and bending moment on a tunnel section taking into account the interaction of the tunnel concrete lining and rock mass. Results of this study show that the loads applied to the tunnel as a result of earthquake waves can be affect the stability of underground structures, especially long structures such as tunnels.

Jan 1, 2011

L.R. Bower In regard to the paper by J.B. Gwiazda, it makes a highly technical approach to show that the µ factor used by designers of lemniscate-guided roof supports has never really been confirmed as a maximum and assumes that convergence is vertical. Also, the paper does not appear to take into account deflection of structures, which occurs when the lemniscate and base members are fully loaded to their maximum stress level, nor the front to back line of the support in relation to differential roof to floor movements caused by strata movements under pressure. It is not unusual for differential movements to be slightly diagonal to the line of the support, particularly in faulted areas and on gradient faces. The paper also does not take into account consolidation of fines immediately above and below the support. Generally speaking, any differential movement is from face to waste and under these conditions the µ of 0.3, which appears to be an international standard, has worked in practice. However, if the face end of the support is lower than the waste end, then the µ of 0.3 can be considerably increased, giving rise to the damage mentioned in the paper. The ideal design should aim for a slightly forward bias in the lemniscate guide so that the last increment of setting is toward the face, tending to close any fissures that may have developed during the support advance cycle. The support should also be fitted with positive set valves to ensure that a high setting load density is attained to minimize bed separation. As far as powered supports are concerned, convergence is irresistible and all powered supports converge at their rated yield load. A similar principle can be applied to the differential roof to floor movements to drastically reduce the very high forces that would otherwise be applied to the lemniscate structures and pins and that, in turn, are transferred to the base arrangement and floor loading. Any differential movements are usually catered for by the 0.3 µ factor or deflection of structures in the lemniscate guide arrangement and consolidation of the floor. The floor loading, due to differential movement, is in addition to the support convergence load and requires additional bearing area to avoid possible floor penetration. Some seven years ago, Fletcher Sutcliffe Wild Ltd. (FSW) introduced a lemniscate-guided shield support where the lemniscate linkage is connected to the roof bar through two horizontally converging rams to allow differential movement to take place above a given rated figure. This is a known force and can be guarded against, whereas with rigid connections the forces, as yet, are unconfirmed. By careful design, a horizontal force in excess of 6 MN (60 tons) opposes differential movements for a total ram loading of only 2.5 MN (25 tons), or 1.25 MN (12% tons) each. This principle can considerably reduce the length and weight of the support in comparison with a rigid pin-type structure ; also, the yield load rating can be increased without affecting the lemniscate forces. The graph shows the tensile and compressive forces in a lemniscate linkage of a support with and without hydrostore. These forces react into both the roof beam and base members and, as can be seen from the support height to linkage load graph, a considerable reduction in these reactions is gained by the use of the FSW patented hydrostore system. Floor loading is considerably reduced under maximum µ conditions, and by allowing the roof bar to move with the strata, some degree of improvement to strata control is achieved in line with the assumptions in the paper. In practice, these movements have only been in the region of a few millimeters, which, in turn, reflects on the improvements to strata control by the addition of positive set valves. Supports to this design of both 450- and 280-t (496-and 309-st) rating have been successfully used in the United Kingdom for several years, negotiating many faulted areas without one single reported need for repair or maintenance. This includes supports left unattended during the year-long strike, proving the reliability of the system.

Jan 8, 1986

By E. J. Berentsen

The Turquoise Ridge gold deposit is located near the Getchell Mine, 72 km (42 miles)northeast of Winnemucca, NV (Fig. 1). The deposit is owned by Getchell Gold Corp. The host rocks consist of Ordovician and Cambrian age shales and limestones. They have been crosscut by the northeast-trending Turquoise Ridge shear zone and northwest-trending shear zones. Gold mineralization occurs at depths from 427 to 671 m (1,400to 2,200 ft) along the intersection of these structures. Large tonnage, flat-lying deposits occur where folded, favorable beds are intersected by the faults. The carbonate in the beds has been replaced with silica, pyrite and arsenic sulfides.

Jan 1, 1996

By B. Samanta

This paper highlights the use of an innovative mine production scheduling scheme for grade-control planning tasks that take into consideration grade-model uncertainty. The scheduling exercise has been carried out with the help of a multiobjective genetic algorithm (MOGa) for the production scheduling operations. The underlying motive behind the use of MOGa has been the generation of a set of pareto optimal solutions to meet the goals of the target-grade specifications for the considered multiple grade attributes. Several new concepts related to MOGa formulation, in particular the mutation operation and the convergence criteria of this algorithm, are proposed in this paper. The modeling of grade uncertainty into the scheduling outputs has also been incorporated through a set of conditional simulated grade maps. The proposed scheme of production scheduling operations has been applied for the grade-control planning operations in an iron ore mine to meet the targeted grade specifications of iron, silica and alumina, and a risk analysis has been performed to this end.

Jan 1, 2013

By U. Srivastava

In the processing of manganiferous ore, it is useful to control whether the manganese (Mn) goes to the iron product to produce ferromanganese, or to the slag for extraction as a high Mn product. This can be done by manipulating the thermodynamic conditions for manganese oxide(MnO) reduction to control whether it remains as MnO or converts to metallic Mn. Results are presented showing that during production of iron nuggets, reduction of manganese oxide (MnO) can be controlled by changing the furnace temperature and reductant composition appropriately.

Jan 1, 2010

By O. M. Arafat, J. A. Finch

Since its development, the functional performance equation for ball milling (McIvor, 1988) has facilitated a new understanding of industrial circuit cause and effect relationships, leading to significant strides in operational performance. Success stories of this approach to plant circuit performance improvement are now too numerous to list. Finch and McIvor (circa 1986) also discovered that the functional performance mill grinding rate at the size of interest was the same cumulative grinding rate that is calculated from mill feed and discharge size distributions using a first-order rate equation. By calculating these cumulative grinding rates for all screen sizes, a complete ball mill model is generated (as used by Finch and Ramirez, 1981). Others in industry, Hinde and Kalala (2009), for example, have noted the same. Lacking the complexity needed to maintain their interest, most researchers have ignored this model, broadly opting instead for Epstein’s (1948) characterization of grinding as a chemical reaction, combining selection rate and breakage size distribution functions. The much simpler ball mill model has previously been incorporated into a proprietary circuit modeling program (McIvor, 2005) and used for plant improvement work (for example, see McIvor and Finch, 2007, and McIvor, 2014). Now, by combining this business-friendly ball mill model with optimization criteria from functional performance analysis, a circuit modeling system (including the needed supplementary steps to assure successful plant implementation of circuit design changes) is at the disposal of every plant metallurgist, grinding equipment/ material provider and circuit designer.

Jan 11, 2017

By Mahaboob Basha Shaik, Shakuntala Tudu, Indrajit Paul, Chandra Sekhar, Neha Gupta, Amit Kumar, Srinivas Dwarapudi, Arvind Kumar Patel

In this study, the effect of colemanite and calcined colemanite (CC) addition on the properties of iron ore pellets is studied. The pellets are prepared in a lab without and with 0.2% colemanite and varying amounts of CC from 0 to 1.0 wt%in steps of 0.2%. A reference pellet is prepared under typical plant conditions, and the properties of the reference pellet are considered as the base value for improving the cold compressive strength (CCS) while maintaining the other parameters at an acceptable limit without altering the pellet. The study also aims to provide a detailed characterization of colemanite and calcined colemanite to better understand their behaviour during firing. The lab-scale results show that the CCS of pellets made with 0.2% colemanite was reduced by 222 points (60%) as compared to the reference pellets due to crack formation during firing. The results show an improvement in the CCS of the indurated pellets with CC dosage up to 0.4%, and decreasing strength is noted thereafter. It is observed that the swelling index increases with the increase in calcined colemanite dosage. To simulate plant conditions, reference pellets and pellets with optimized CC dosage were fired in a plant furnace.

Oct 16, 2020

By L. Yuan, J. Soles, D. Bahrami, W. Tang, R. Thomas

Mine equipment fires remain as one of the most concerning safety issues in the mining industry, and most equipment fires were caused by hot surface ignitions. Detailed experimental investigations were conducted at the NIOSH Pittsburgh Mining Research Division on hot surface ignition of liquid fuels under ventilation in a mining environment. Three types of metal surface materials (stainless steel, cast iron, carbon steel), three types of liquids (diesel fuel, hydraulic fluid, engine oil), four air ventilation speeds (0, 0.5, 1.5, 3 m/s) were used to study the hot surface ignition probability under these conditions. Visual observation and thermocouples attached on the metal surface were used to indicate the hot surface ignition from the measured temperatures. Results show that the type of metal has a noticeable effect on the hot surface ignition, while ventilation speed has a mixed influence on ignition. Different types of liquid fuels also show different ranges of ignition temperature. Results from this work can be used to help understand equipment mine fires and develop mitigation strategies.

Mar 2, 2022

By H. Hinds

Plant testing of DuPont's Activator Technology in the vat leach circuit of the Homestake mine shows increased gold recoveries of 3-5%. Activators are catalysts of gold dissolution in cyanide solution. DuPont received the patent for this technology in January, 1996. The test was run in the west sand plant alternating control and activated vats to reduce the variability in head grade and cyanide consumption. Activated vats had gold in the preg solutions earlier, higher gold recovery, and lower gold residuals. Activator addition did not adversely affect mill operations or the environment. Optimization of the technology continues.

Jan 1, 1997

By Robert G. Bottge, Paul C. Hyndman, Don J. Barnes, Clark A. Roberts

The effect of Federal restrictions on Federal mineral estate in Alaska and the Western States is being addressed by systematic, State-by- State studies. The Bureau of Mines has inventoried and classified 3.5 million sq km (876 million acres) of land, section-by-section, according to 1) mineral ownership, 2) availability for mineral exploration and development as affected by Federal restrictions, and 31, areas containing mines and mineral resources. The availability of Federal land for exploration and development is spatially compared to areas containing mines and mineral resources. The methodology and overall results of the studies are presented.

Jan 1, 1991

By E. M. Hill, D. E. Walsh, J. T. Hollow, H. K. Lin

Fairbanks Gold Mining, Inc. (FGMI) began blending and processing True North ore at their Fort Knox mill on April 12, 2001.Gold extraction subsequently dropped from 88% to 71% during the last week of April 2001. 25% of the gold values remaining in the leach tailings were gravity recoverable free gold. Significant quantities of stibnite and arsenopyrite were also identified in the tailings. In laboratory bottle roll tests, the gold extraction from a composite of leach circuit feed collected during the same period was 72.6%, when leached at an average NaCN concentration of 0.16 g/kg. The extraction increased to 82.4% and 91.7% with 0.5 g/kg NaCN, and 0.5g/kg NaCN plus 0.075 g/kg Pb(NO3)2, respectively. A passivating layer surrounding liberated gold particles and resulting from sulfide mineral dissolution, likely contributes to reduced gold recovery, which can be substantially increased by the addition of lead nitrate. Lead species remain in the solid residues after leaching and were not mobilized using Meteoric Water Mobility Procedure.

Jan 1, 2003

By Greg Colzani, Emily Thompson

The 3RPORT Project, includes a 5-mile tunnel excavated by a 19-foot diameter slurry Tunnel Boring Machine below the city of Fort Wayne, IN. The Geotechnical Baseline Report (GBR) indicated vuggy to massive argillaceous dolomite within the tunnel alignment. During excavation of the first reach, the TBM encountered zones of cohesive clay and sandstone presented in full face and mixed face conditions. The occurrence of Sandstone was not a “Baselined Condition” described in the GBR for this reach of the alignment. This paper will discuss the methodology to investigate, mitigate and evaluate the DSC impacts on TBM performance.

Dec 1, 2022

By D. J. Barratt

The application of autogenous and semi-autogenous grinding circuits in recent years has contributed toward substantial savings in capital and operating costs compared to conventional circuits, particularly for large scale copper and molybdenum operations. Such savings have been realized from the deletion of operating, maintenance, equipment purchase and substantial civil/structural costs associated with secondary-/tertiary crushing and screening, fine ore storage and conveying. In spite of the downturn in the copper- moly industry in North America, there is still an interest in autogenous and semi-autogenous grincting for copper-zinc, gold and silver ores and in the overseas market. Both single-stage and two-stage circuits are in operation. Primary circuits operate autogenously or semi-autogenously in either open or closed-circuit. Critical sizes are extracted and crushed for recycle in some cases (e.g. ABC circuit). Secondary grinding is conducted using ball mills or pebble mills.

Jan 1, 1985

By Rolf Pollak, Jan Tegtrneier, Gerhard Keller, Horst Gerhardt, Wolfgang Müller, Dieter Tetzner

INTRODUCTION Under certain geological and mining conditions mining near the surface results in an intensive destruction of the overlying rock strata. If the system of mine openings remains filled with air after having completed all mining activities because the flooding of the mines depending on the morphology of the mining area does not exceed a certain level, this circumstance might result in dangers for the public. This is particularly true where uncontrollable air- ways occur within the destroyed rock or if former uranium mining areas are concerned. In these areas radon emanation resulting in undue radon concentration should be taken into account. This circumstance can be counteracted by suitable measures of ventilation. In the following the example of a uranium deposit in the Erzgebirge Mountains (Saxon Ore Mountains) is used to illustrate how statements about the ground flow through overlying rock can be made on the basis of systematic investigations. Finally comparisons with experience gained in coal mining yield orientation data which are used as input quantities in ventilation network calculations and in project preparation of mine fans. Last not least it is proved that endangering the population by radon can be excluded by installing an appropriate fan. INITIAL SITUATION From 1946 to 1989 the uranium deposit of Schlemal-Alberode was mined starting from superficial zones down to depths of 1,800 m. The total output amounted to 80,000 t of uranium, i.e. Schlemal Alberode is one of the largest uranium deposits in the world. The mine openings comprise a cavity of 40 million m3. Al- though thin seams (0.2 to 0.3 m) and steep to semi-steep veins (60 - 70 degrees on average) were extracted using the method of overhand cut-and-fill there were also deposit sections with larger thicknesses and poor ore zones, respectively, where especially after the war until about 1955 large openings were formed due to missing filling. Due to this uncontrolled, relatively "wild" mining considerable subsidence of the surface and fractures in the border zone of the subsidence area occurred. The town of Oberschlema was destroyed and an area of 0.14 km2 was damaged by mining involving a maximum subsidence of 6 m in the centre - called deformation area. The rehabilitation work for the deposit area of Schlemal Alberode involves the flooding of the openings up to a level of the Markus-Semmler-Sohle as long-term preventive measure. Fig. 1 shows the flooding level of October 1996. The level of the -540 m drift will probably be reached in June 1997. From that point of time a general rearrangement of the ventilation has to be made because the central return air ventilation via shaft 373 will no longer be possible. This shaft has no connection with the superficia1 system of mine openings. A new return air ventilation system based on shaft 382 as return air shaft will be designed (Fig. 1). The capacity of the future mine fan system will e.g. be determined by the flow conditions in the deformation area mentioned above. For this reason investigations were carried out in a test drift 13a on the level of the Markus-Semmler-Sohle in the stretching zone of the subsidence trough for several days (Fig. 2 and 3). INFLUENCE OF THE OPERATING CONDITIONS OF THE MAIN MINE FAN ON THE RADIATION SITUATION ON SURFACE The beginning of flooding in 1991 was also the beginning of the investigations into the options of future ventilation due to the reduction of the mining area. The first analyses of radon emanation made in May 1991 showed that only about 20 % of the total radon emanation result from systematically ventilated mine workings. This means that despite of existing dams the air streams through the majority of mine openings of the deposit. The analysis of the individual radon inflows illustrates the special problematic nature of the deposit involving all possible effects on the surface. The shutdown of the main mine fan over the long period between 2.10. and 6.10.1991 showed the essential influence of the operating conditions of the fans on the whole radiation situation on surface. Fig. 4 shows the comparison of the radon concentration level and its daughters during a 'normal" weekend with the level during long-term shutdown in the old 'Casino" of the papermill of Niederschlema. This papermill as well as the 'Casino" are situated in the outcropping zone of the deposit section of Niederschlema. The -60 m level was driven as the upper level in this area, from which the panels were driven to about 20 m below the surface. Also below the "Casino" there is such a panel in the vein 'Glirck", whose roof is directly situated below the building in a depth of 39 m. Directly next to it there is the raise 2 of the panel 'Namenlos" in a depth of 27 m. The graphics clearly shows the immediate increase in radon concentration as well as in the daughter concentration after the shutdown of the fans. The elimination of the artificially generated negative pressure results in the reversal of the convection direction due to the natural ventilating pressure. The interface structure allows the mine airto pass through aero- dynamic connections to the surface. Neglecting the meteorological parameters the concentrations of radon and its daughters in- creased by about 350 % as compared to a 'normal" weekend during longterm shutdown (i.e. in 4 days). Furthermore it could be noticed that a stationary state between the radon and its daughters has not been established in the period

Jan 1, 1997

By Shakuntala Tudu, Indrajit Paul, Surajit Sinha, Pulibandla Basaveswara Rao, Shaik Mahaboob Basha, Srinivas Dwarapudi

The iron and steel manufacturing sector directly accounts for 7–9% of global CO2 emissions. Raw material preparation, such as iron ore sintering, pelletizing, and cock making, is the major CO2 emitter. As climate change becomes a bigger concern, steel manufacturers need to lower CO2 emissions without hindering efficiency or increasing costs. In recent years, the percentage of iron ore pellets in blast furnaces has increased due to its uniform size, good reducibility, and high tumbler index. Pelletizing is energy-intensive and emits considerable CO2. Around 20% of CO2 emissions during pellet making come from fluxes. In the present work, the authors established a novel CO2- free flux called wollastonite (CaO.SiO2) for sustainable palletization. Pellets with varying percentages of wollastonite (0–6%) are prepared and tested for chemical, physical, and metallurgical properties. Image analysis through an optical microscope is carried out to quantify the phases of fired pellets. SEM–EDS is performed to evaluate the chemical composition of the melt and slag phases. The results showed that the reducibility index (RI) and swelling index (SI) of pellets decreased with an increase in wollastonite dosage. Pellet strength increases with an increase in wollastonite addition up to 1.2% CaO (2.27% wollastonite), and a decrease in strength is observed thereafter. The increase in strength is attributed to the increase in slag bonds. The decrease in strength beyond 1.2% CaO is mainly because of an increase in low melting eutectics and more magnetite content. Pellets with 2.27% wollastonite to get 1.2% CaO showed good physical and metallurgical properties.

Mar 4, 2024

By David L. Gefvert

A general review of the role of cationic flotation reagents in the beneficiation of phosphate, iron, and potash ores. The three major types of cationic collectors-amines, ether amines, and condensates will be compared and contrasted. The effect of particle size, water chemistry, and water temperature on the choice of cationic flotation reagents for each industry will be discussed.

Jan 1, 1986