Search Documents

By Steven A. Bradbury

INTRODUCTION Passive dust control systems are quickly gaining acceptance in the bulk solids handling industries. The number of applications is increasing due to proven performance, especially in US power plants burning Powder River Basin coal. Air Control Sciences ®, Inc., of Boulder, Colorado, has over forty (40) patented Dustless Transfer ® systems in operation. All of the installations control workspace dust levels to less than 2.0 mg/m3, and in some applications reduced conveyor dusting by over ninety-eight percent (98%). Passive systems control fugitive dust emissions by minimizing the induced airflow in bulk material transfer and slowing its velocity. Traditionally, fugitive dust control in the mining industry was accomplished using either dust collection systems or dust suppression systems. The term passive dust control, indicates these methods don't use any active dust collection or suppression. Passive dust control systems are best suited to transfer from one conveyor to another. They can also be applied to transfers from feeder to conveyors.

Jan 1, 2004

By G. Wozniak, R. Rostanski, H. Pfanz, G. Aschan, E. Sierka

"Industrial wasteland is a typical element of the landscape of all the industrialised regions in Europe. There are many examples from Poland as well as from other European countries that post-industrial sites have been undergone natural colonisation and succession to establish in some cases ecosystems of greater biological diversity than the original ecosystems. The post-industry sites regardless of any reclamation carried out, undergo natural successional processes. The respective biological diversity (number of species, and number of plant assemblages) reflects the micro-variety of the specific habitat. This paper summarizes the results of investigations, which have been carried out since 1989 on coal mine water sedimentation pools in the Upper Silesia Industry Region. The aim of this study is to demonstrate the diversity of spontaneous plant communities recorded on post-industrial waste sites. In the course of the long time fieldwork, plant assemblages representing nine phytosociological groups have been identified."

Jan 1, 2005

By M. Yavuz

Multiple Criteria Decision Making (MCDM) is one of the most considerable branches of Operation Research. MCDM refers to making decisions in the presence of multiple, usually conflicting, criteria. The problems in MCDM are classified into two categories: Multiple Attribute Decision Making (MADM) and Multiple Objective Decision Making (MODM). However, very often the terms MADM and MCDM are used to mean the same class of models and mostly confused in practice. Usually, MADM is used when the model cannot state in mathematical equations and otherwise MODM is used (Hwang and Yoon, 1980). Decision-making (DM) is extremely important stage in Mining Engineering like other engineering branches. Every mining engineer makes several decisions in daily mining applications. Most of the decisions made by mining engineers are completely instinctive according to their past experiences and there is not any DM method applied in DM process. Analytic Hierarchy Process (AHP) is one of the well-known techniques solving the decision problems. The AHP is very simple, and understandable method especially non-numerical data considered in DM process. Equipment selection is one of the prominent problems of mining engineering. Mining engineers have to make difficult decisions when equipment selection stage. As the decisions in the equipment selection have radically influenced the economic life of any mining scenario, these are considered as complex MADM problem. So, the decision maker can evaluate the subjective criteria in the problem of equipment selection. The decision maker wants to maximize more than one objective criterion for equipment selection stage. Among the number of alternatives, the most suitable equipment must be selected according to objectives and alternatives. MADM applications can help the decision maker to reach the optimal solution for the equipment selection. In the mining industry, MADM methods can be applied for the equipment selection because it is a process that includes subjective and objective criteria affecting the selection of equipment among the alternatives.

Jan 1, 2007

ME?s Arizona Conference was held at the Hilton El Conquistador resort in Tucson on Dec. 2 and 3, 2007. The annual conference is organized by the Arizona Conference Board of Directors, which represents SME sections in Arizona and adjacent areas. The conference provides an opportunity for individuals and corporations associated with mining in the region to get together once each year to discuss the status of the industry. The 2007 meeting featured a keynote address, a distinguished lecturer and more than 25 technical papers that were presented in seven sessions. The sessions included environmental, geology, safety, metallurgy, mining, new projects and a special session on Mexico. Topics covered included mine closure, sustainable mining, exploration methods, health and safety issues, mining equipment and drilling. Much of the discussion at the conference concerned major new developments in the region?s copper mining industry. For example, Freeport-McMoRan?s new Safford Mine and BHP Billiton?s Pinto Valley restart were the topics of technical presentations. There was also much discussion among the attendees on the current and future price of copper, community relations, education issues and recruitment concerns. At the time of the conference, the price of copper hovered around $3.30/lb, up considerably from the 61 cents/lb in late 2001, when the industry was being challenged by world market conditions and a weakened domestic economy. Since then, strong demand from China helped push copper prices to record levels that at one time reached as high as $4/lb. The general consensus among the attendees is that the current price of around $3.30/lb will continue through 2008. Most attendees also expect increased corporate investments in the industry to continue. Copper mining in Arizona has been a major industry since the 1800s. In 2007, Arizona was the leading copper-producing state in the United States and produced more than $5 billion worth of copper. The copper mining industry in Arizona also produces byproduct gold, silver and molybdenum. Arizona is the second largest molybdenum producer in the United States.

Jan 1, 2008

By Andreas Prucker

The Greater Vancouver Water District (GVWD) is currently constructing the largest water treatment plant in Canada. As part of this treatment scheme twin water transfer tunnels are being constructed. Work commenced with the 11 m diameter, 185 m deep Seymour Shaft which was excavated by drill and blast using a mobile crane for hoisting. The Seymour Shaft is the first large diameter shaft that has been sunk in Western Canada in recent years. The operational aspects associated with the hoisting, the drill-blast-support cycle and water control in the shaft are the focus of this paper.

Jan 1, 2008

By R. Hildebrandt, K. Cybulski, G. V. Goodman, Z. Dyduch, M. L. Harris, M. J. Sapko

Past research showed that bituminous coal dust remains dry and dispersible in the presence of moisture. Rock dust must disperse with the coal dust to effectively inert a propagating coal dust explosion. Non-treated rock dust readily absorbs moisture, limiting its dispersibility, while anti-caking treated rock dusts can remain dry. The National Institute for Occupational Safety and Health contracted the Central Mining Institute in Poland to conduct large-scale testing in their Experimental Mine Barbara to determine if a treated rock dust can be as effective as non-treated rock dust in attenuating or quenching coal dust explosions under the same experimental conditions. INTRODUCTION One of the goals of the National Institute for Occupational Safety and Health (NIOSH) is to conduct research to reduce the risk of mine disasters and provide workplace solutions to reduce the risks associated with accumulations of combustible and explosible materials; the most common form of which is the generation of coal dust during the mining process and its subsequent distribution downwind. Dispersible rock dust is a primary defense for preventing coal dust explosion propagation in underground coal mines, and its properties are defined in 30 CFR 75.2. “Pulverized limestone, dolomite, gypsum, anhydrite, shale, adobe, or other inert material, preferably light colored, 100 percent of which will pass through a sieve having 20 meshes per linear inch and 70 percent or more of which will pass through a sieve having 200 meshes per linear inch; the particles of which when wetted and dried will not cohere to form a cake which will not be dispersed into separate particles by a light blast of air; and which does not contain more than 5 percent combustible matter or more than a total of 4 percent free and combined silica (SiO2), or, where the Secretary finds that such silica concentrations are not available, which does not contain more than 5 percent of free and combined silica.” An earlier NIOSH investigation of rock dust revealed two significant concerns with the supply of rock dust to U.S. coal mines: 1) insufficient particles <200 mesh (75 μm) and 2) all rock dusts when wetted and dried formed cakes and were not easily dispersed with a light blast of air (1). Past research by the U.S. Bureau of Mines and others showed that bituminous coal dust remains dry and dispersible in the presence of moisture (2). Rock dust must also be dispersible in concert with the coal dust to effectively inert a propagating coal dust explosion (3, 4, 5, 6). Non-treated rock dust, however, readily absorbs moisture, limiting its dispersibility, while a rock dust treated with long-chain fatty acids (such as stearic acid) can remain dry and dispersible. Stearin-treated rock dust has been used in British coal mines (7) and is commonly used in Polish coal mines.

Jan 1, 2019

By G. K. Hoffman

Humate, defined as weathered coal or mud-stone rich in humic acid (HA) and fulvic acid (FA) have been mined, primarily as soil amendments or drilling mud additives, in New Mexico for 15-20 years. The New Mexico humate resource is estimated to be 11 Gt, including weathered coal and organic mudstone. The HA and FA content determines the end-use, therefore a simple and consistent method of measuring organic-acid content was developed. The New Mexico Bureau of Mines and Mineral Resources method is based on repeated alkali leaching and acid precipitation. Precipitates of humate are ashed, with mass balance of solids maintained, to correct for material added during alkali-acid treatment. Analyses of upper coal member, Cleary Coal Member (Menefee Formation) and Fruitland Formation samples from the southeast San Juan Basin show ashing to be important in accurate analysis of FA content. Ash in the total FA fraction averages 70% compared to 2% in HA. The FA in weathered coal and organic mudstone are similar, although HA is significantly higher in the former. As weathering progresses, the FA content of weathered coal increases faster than in organic mudstone because of the greater total organic material in coal.

Jan 1, 1994

By Takashi Goto

In 1968 three historical rockbursts had occurred at Bibai Coal Mine in Hokkaido. At the time they had been observed by several seismic observatories as natural earthquakes away more than 100km from Bibai City. These facts taught us that the occuerrence of failure yielded in underground opening that was accompanied with seismic wave could be observed by seismometer on the surface. After two years from this desaster, the study concerning to microseismic events generated from underground mining panels has been begun by researchers with heart-throb.

Jan 1, 1982

By Mark A. White

Surface mining of multiple seams by mountaintop removal and contour mining is complex in Appalachia. Arch of West Virginia, a division of Apogee Coal, has made its operations state-of-the-art to cope with this challenge. Arch of West Virginia moved into the heart of coal mining in Appalachia when Arch Mineral acquired coal reserves and coal operations in the southern West Virginia counties of Logan and Wyoming. These reserves were initially developed at the turn of the century as underground operations. Today, though, they are mined using mountaintop removal and contour mining. The steep slopes in the mountains of Appalachia generated a method of mining referred to as contour mining. During the late 1960s and early 1970s, contour mining was introduced at these operations using front-end loaders with bucket capacities of more than 7 m3 (10 cu yd) that could load 45-t (50-ton) end-dump trucks.

Jan 1, 1995

The use of coal as a fuel causes air, pollution in; a number of different forms, and in nearly all stages of its, handling, preparation, storage, use and-disposal of its residue. First let us consider the handling of coal. As shipped, particularly to large utilities, it is run-of-mine bituminous made up of large chunks as well as pulverized particles. Because it &apos;is in an open car or barge, it is subject to the action o winds and the small particles may be blown around adding to the-particulate load in the atmosphere. Mien un¬loaded from the barge or car, there is again an opportunity for the wind to blow the fine particles around. All of us I am sure have seen a barge at the dock of a utility plant being unloaded by a clamshell bucket. This, after grabbing its load from the barge, lifts it some 60 or 70 feet and, then drops it on a conveyor, which carries the coal to a storage area.

Jan 1, 1964

By E. C. Westman, F. J. Shreve

This paper presents the design and construction of a multi-channel geophone array that improves tomographic imaging capabilities in both surface and underground mines. Especially important in the design of the array is sensor placement. Three issues related to sensor placement are addressed in this paper: 1) sensor placement in long, horizontal boreholes, 2) development of simple, robust, MSHA-acceptable clamping unit, and 3) orientation of the geophones within the borehole. Improved imaging capabilities will produce energy, environmental, and economic benefits by increasing exploration accuracy and reducing operating costs.

Jan 1, 2002

By Tim O’Neil

Big and getting bigger. Barrick Gold Corp., the third-largest gold producer in the world, began production in September — ahead of schedule — at its Meikle Mine. At a scheduled full production rate of 12.4 t/a (400,000oz/year), it will be the largest producing underground gold mine in the United States. The $180-million Meikle Mine is located on Barrick’s Goldstrike property in Nevada and has 205 t(6.6 million oz) of gold reserves. The compact Meikle deposit has an average ore grade of 23 g/t (0.68 oz/st), making it one of the highest-grade mines in the country.

Jan 1, 1996

Analysing a flotation plant?s operating performance requires accurate metallurgical sampling. Typically, the aims of performing flotation plant surveys are to establish a consistent and accurate understanding of the operation of the circuit as well as to identify potential areas for improvement. Once the data have been collected, a mass balance is required to provide a consistent set of data from which plant performance can be assessed. Mass balancing is a key skill that many metallurgists and mining industry professionals are familiar with. Mass balancing reconciles the feed and product streams throughout the plant and is sometimes used for accounting of the material entering and leaving a system (eg. JKMetAccount). However more common reasons for mass balancing are: better understanding of the flowrates within a system, assessing the quality of data obtained from sampling and surveys, and providing a key dataset for assessing and improving the performance of unit operations. Mass balancing requires practice and experience to determine if the results are reasonable. There are various software programs available to assist in the mass balancing and understanding of processing plants. This paper is focused on JKMultiBal initially developed by Gay (1993), and then later commercialized by JKTech. JKMultiBal in its current release is for balancing data in both one and two dimensions, i.e. balancing data on either sized or assay bases as well as size-by-assay. With the recent trend in flotation circuits becoming more complex, JKMultiBal has been used to gain a better understanding of the processes occurring within the circuit. This paper provides a description of the program as well as several case studies where the two-dimensional mass balancing has resulted in improvements in plant performance.

Jan 1, 2009

When looking for indicators for the mining business ? and these days who isn?t? ? one might need to look no further than the SME Annual Meeting. Held in Phoenix, AZ Feb. 28 to March 3, the meeting was, by almost any measure, a record-breaking success. Attendance included 4,937 industry professionals. Many of whom, feeling rejuvenated following the worst economic recession since the great depression, were greeted with a record 630 exhibits and 103 technical sessions covering all aspects of the mining and minerals business. Adding to the general optimism of the future was a celebration of the past and re-cent achievements in safety and health. The theme of this year?s meeting was ?Celebrating 100 Years of Mining Research? and the emphasis on advancements in safety was evident from the keynote address that kicked off the conference, to the field trips, to the Resolution and Safford mines that concluded the meeting.

May 1, 2010

By J. M. Mutmansky

This paper outlines the results of a study of opinions of practicing engineers concerning the value of environmental engineering courses in a mining engineering curriculum. One hundred engineers with significant experience in mining-related engineering work were carefully chosen. Of the sixty-seven responses received, about half were from mining engineers and half from environmental engineers. The results of the survey are outlined in detail. The number and type of courses recommended by the respondents are summarized as well as the specific topics recommended for inclusion in a mining engineering curriculum. The survey form also asked for the stages in the mine life when environmental experts were needed and the percentage of environmental engineering performed by outside experts for many mining-related environmental tasks. The results of this line of questions are provided. Finally, the paper offers a comparison of the results for environmental engineers and mining engineers and analyzes the differences.

Jan 1, 2001

"Cast blasting is the primary means of overburden displacement in a surface coal mine. It serves two purposes; fragmenting the rock and throwing it directly to its spoil pile using explosive energy. Increased throw minimizes costs by reducing the amount of material that needs to be rehandled. Prior studies have shown that by only changing blasthole timing with the same blast design, fragmentation and throw alter. It is necessary in cast blasting to optimize both fragmentation and throw, since larger fragments will require more wasted energy to throw the same distance. In an operating mine in Georgia, an optimum interhole delay for fragmentation has been found by studying timings from 0 millisecond (ms) to 45 ms. Instantaneous timing between holes increased the throw by more than 31 m (100 ft), but fragmentation was poor. Shock and detonation wave collision is a potential reason for this increased throw.Explosives are utilized extensively by the mining industry in order to break rock, as either ore or overburden, for hauling, loading and crushing. An effective production blast strives to achieve optimum rock fragmentation in order to increase the efficiency and reduce the costs of those downstream operations, while simultaneously meeting environmental regulations. The goal of blasting with respect to fragmentation is, according to Hettinger (2015), “to decrease the average particle size of the fragmented rock without overly increasing fines or, in other words, improve fragmentation.”Additionally, the distance the rock is transported by the explosive energy from the blast, also known as throw, can increase efficiency by reducing the amount of material that is rehandled by mine equipment. The primary situation in which this is desirable is the cast blasting of overburden across the narrow pit of a surface coal mine. A key variable in a blast design pattern that can be manipulated to optimize both fragmentation and throw is delay timing between detonations. The invention and increased utilization of electronic detonators have allowed for precise delay timings to be used between rows, holes and even multiple primers within the same hole. These recent developments in the blasting community have also provided an opportunity to investigate whether or not the mechanism of shock or detonation wave collisions caused by short timing delays are responsible for any increased fragmentation or throw. This experiment attempts to demonstrate if an increase in throw can be achieved while maintaining optimum fragmentation."

Jan 6, 2017

By A. Adu-Acheampong

Photogrammetry and laser scanning has been employed at a number of Newmont mine sites to mitigate risks associated with conventional structural mapping, determining the geometry of voids from old underground workings, and generating topography in areas of slope instability. Laser scanning has also been used to evaluate as-built pit slope configurations with respect to design assumptions, operational practices, and rock fall potential. Recently, remote sensing applications carried on an unmanned aerial vehicle (UAV) were used to generate base topography at some Newmont sites. UAV are generally more convenient and less expensive and can be utilized in areas where cloud cover prevents manned aerial photography missions. This paper discusses these applications, and provides commentary on their benefits and limitations based on recent experience.

Feb 27, 2013

By B. J. Timmons

An initial point that I would like to make very emphatically?and as our title might erroneously suggest for those of you old enough to remember . . . Peter Harben and myself do not intend to shoot ourselves in the foot. We derive our livelihood from a number of aggregate, industrial and other minerals producers, both here in the United States and outside. This paper, therefore, is a fence-straddler or for information purposes (we hope) only, rather than any "fur or agin" stances. In essence, some of you may consider it a U.S.G.S. publication! In fact, we hope that it serves to inspire aggregates producers to do some radical thinking, to promote introspection, and to that end it would benefit both domestic and foreign producers. The title could be shortened into a brief question of "Aggregates Travel?" with an emphatic no for the answer. In the past, the success of a construction materials venture depended upon your ability, through siting, to provide the customer f.o.b. the job site, a product at the lowest possible cost.

Jan 1, 1987

A bearing isolator is a noncontact, nonwearing, permanent bearing protection device. It has a rotor and a stator, and the two are unitized, so that they do not separate from one another while in use. The rotor turns with a rotating shaft, while the stator is pressed into a bearing housing. The two components interact to keep contamination out of the bearing enclosure and the lubricant in. Bearing isolators do not require lubrication or any particular shaft finish or condition. The best bearing isolators are made of metal, usually bronze. They use a vapor-blocking feature that inhibits the free transfer of vapor contamination when the rotating equipment is cycled on and off.

Jan 1, 2004

By M. Polat

Variations in flotation rate by particle size and specific gravity have been investigated for three different bituminous coals. The flotation rates for various components were determined by separating the products of bulk flotation into size-specific gravity fractions. The effects of feed size and reagent addition on the flotation response of individual size-specific gravity fractions were evaluated.

Jan 1, 1994