Search Documents

By M. Mikhaylenko

Rhenium, molybdenum and tungsten are the elements demanded by high-end technologies. These metals are found in process solutions in forms of their oxyanions: ReO4-, MoO42- and WO42-. The later two can exist in forms of iso- and/or heteropolyanions. Basically all three metals demonstrate very similar chemical behavior in aqueous solutions. Unfortunately, in their mineral sources these elements commonly accompany each other, like pairs of rhenium-molybdenum or molybdenum-tungsten. Their economical separation is a challenging task.

Jan 1, 2012

By P. Zhang

Phosphate mining in Florida generates approximately 100,000 tons/day of phosphatic clays (slime). This waste slime not only creates one of the most difficult disposal problems in the mining industry, but also causes tremendous loss of P2O5. About 20-30% of the phosphate mined end up in phosphatic clays. Recovering the phosphate from this waste is difficult for two main reasons: 1) the slime is extremely fine in size, and 2) clay minerals account for almost half of the material. A half dozen dispersants were evaluated for keeping the clay minerals suspended for subsequent separation from non-clay minerals by either settling or cycloning. The separation efficiency and economics are discussed.

Jan 1, 1998

By Richard F. Coon

Six potential locations along the west shore of Lake Mead were evaluated to site anew water intake pumping station for the SNWA. The evaluations were based upon geotechnical exploration results and conceptual intake pumping station designs. The exploration included geologic mapping, geophysical testing, underwater ROV inspections and borings. Ground surface and underground chamber pumping station designs were considered. Sites at Saddle Island, Black Canyon and Hoover Dam are geotechnically suitable. A Saddle Island site was selected because it has the most favorable conditions for the intake pumping station and the aqueduct to the Las Vegas valley.

Jan 1, 1997

By H. A. Taylor

Graphite is elemental carbon that crystallizes in the hexagonal system as six-sided platelets. It occurs naturally and is mined. And it can be made artificially from petroleum coke in the form of shapes (electrodes) and powders. The market for most kinds of graphite in most end-uses was good in 2004. The 2005 graphite market looks positive. The major graphite prices, as given in Industrial Minerals, remained unchanged throughout the year. The preliminary 2004 U.S. Geological Survey (USGS) prices for natural graphite showed almost no change for crystalline flake. They were $600/t ($544/st) in 2004 and$622/t ($564/st) in 2003. Mexican amorphous graphite was almost unchanged at $150/t ($136/st) in 2004 from$152/t ($138/st) in 2003.

Jan 1, 2005

By Bruce Geller

The 2004 Prospectors and Developers Association of Canada (PDAC) conference contained an air of optimism and excitement that has not been seen since 1997. Many segments of the mining industry are alive and well. This is largely a reflection of improved metal prices, themselves due to the strong euro and improvements in Asian economies. Those factors offset higher oil prices, a weaker U.S. dollar and concerns about the Middle East. This report is an overview of the conference. It is supplemented by an examination of conference handouts, abstracts and a few complete papers that are on the PDAC’s Web site www.pdac.ca. Sixty PDAC 2004 abstracts are available at the same site, along with 15 complete papers in PDF format. The conference was held March 7-10 in Toronto, Ontario. It was attended by a record 9,200 delegates from 85 countries. About 8,000 people from 74 countries attended the 2003 conference.

Jan 1, 2004

The only significant iron ore deposit in Hungary could be found in Rudabánya. The mine was closed in 1986. The area of Rudabánya was always the home of heavy mining activity. In former times, mainly silver and other non -ferrous metals were excavated.

Jan 1, 2011

By Wm. Ross Wayment, Innes P. Grantmyre

INTRODUCTION It has been recognized for some time that major changes in mining methods will be required in the near future. Two types of factors contribute to this need for change. Intrinsic factors include ground control problems associated with mining at increasing depths, noise, dust, toxic fumes, and logistics problems which arise from operation in a cyclical fashion. Extrinsic factors include competition for labor from industries offering safer and less difficult work, pressure for less impact on the environment, and changing economic and political conditions. The search for new mining methods has resulted in extensive research being carried out on such novel approaches as thermal fragmentation, high-pressure water jets, sonic drilling, microwave fragmentation, and laser cutting, among others. Joy Manufacturing Co. has elected to concentrate on impact breaking in stopes as a first generation continuous hard rock miner. IMPACT BREAKING Fragmentation techniques show a drop in specific energy as efficiency improves. Specific energy is the energy consumed per unit volume of rock removed and is affected by such variables as rock material properties, fragmentation method used, operator skill, tool design, etc. Mechanical fragmentation methods generally have specific energies much lower than that of the more novel methods. Table 1 shows impact breaking to have an efficiency exceeded only by that of drill and blast methods and it is this high efficiency which led Joy to impactors as the subject for research on potential mechanisms for continuous mining in hard rock.

Jan 1, 1976

By L. B. Hales

Image analysis for feed belts and flotation has been used for over 20 years. It has been shown to aid in the modelling and optimization of Sag Mill circuits, and any improvements in the image analysis result in improvements in the model for control. Using a laser to measure the height-profile of rocks on the conveyor has been shown to increase the accuracy of the size classification. We have developed a system using two cameras in a stereoscopic configuration to provide height-profile measurement without the added expense and safety concerns of using a laser. Additionally, we have developed a novel technique for calibration of the system, using artificial intelligence techniques to optimize the model fit by adjusting the image analysis tuning parameters to values resulting in the best classification.

Feb 27, 2013

By J. Garretson

When mining accidents occur, workers often become trapped and/or incapacitated. Current rescue operations can be dangerous and too slow to produce favorable outcomes. Currently, no method exists for rescue crews to scout ahead at critical times to assess the situation. Sandia National Laboratories (SNL), through a National Institute for Occupational Safety and Health (NIOSH) sponsored program has developed the Gemini-Scout mine rescue platform. The Gemini-Scout was created to assist in underground mine rescue missions. It has been designed to go into potentially hazardous environments to assess the conditions (structural, air quality, temperature). In addition, it will enable two-way communications with potential survivors prior to human rescue teams being able to enter the area. The Gemini platform is a dual tracked-chassis design, which gives the robot excellent mobility in unstructured environments. The design includes a passive 2-degree of freedom joint between two identical bodies allowing for ±30deg of pitch and roll. In addition to the base mobility platform, the Gemini-Scout incorporates many other features to help it succeed in its underground mission. The electronics are mounted in explosion proof housings to ensure safe operations in hazardous gas environments. The platform is also able to operate in up to 18in of standing water with its elevated pan/tilt cameras for navigation. A four-channel video link and Two-way audio on the vehicle help to ensure located survivors can communicate with the robot operators. The platform also incorporates a Mine Safety and Health Administration (MSHA) approved multi-gas sensor to monitor air quality. SNL believes that this technology is broad enough to be appealing to other first responders, such as police, firefighters and medical personnel. Gemini could easily be fitted to handle earthquake and fire scenarios, and it could provide relief in currently inaccessible situations.

Jan 1, 2012

By T. Lilley

The use of membranes in wastewater systems has increased rapidly in recent years. Microporous or semi-permeable barriers augment conventional chemical or biological processes to meet stringent treatment targets. These developments enable elegant solutions to wastewater discharge challenges and extend the scope of water recycle redressing the overall water balance and operational economics Wastewater treatment processes are discussed by reference to the spectrum of waterborne contaminants and the respective membrane separation capabilities. The role chemical pre-treatment to enable physical separation of metals with micro-filtration (MF) is described and how integration of MF with reverse osmosis (RO) is used to control a broader range of dissolved contaminants Membrane configurations are considered apropos function, operational economics and sustainability. These features are exemplified with case studies. Firstly, MF alone following chemical precipitation for the removal of heavy metals, then MF onto two stages RO of different configurations for TDS reduction and waste volume minimisation and finally an open channel RO alone for the reduction of inorganic COD from a leach stream.

Feb 27, 2013

By E. A. Metz

Perfect combustion in an engine would produce only water vapor, carbon dioxide and nitrogen as by-products; however, complete combustion is never achieved. As a mobile power plant, the diesel engine is relatively inefficient in terms of energy produced from the energy potential of the fuel. The diesel is not a perfect engine. The fuel burned can undergo a very large number of reactions in the combustion chamber. It only stands to reason that a large number of compounds are contained in the exhaust, actually, thousands of chemicals. The exhaust can be broadly divided into a gaseous phase and a particulate phase. Each phase is made up of organic and inorganic compounds. The vapor phase contains carbon monoxide, sulfur dioxide, various oxides of nitrogen and many hydrocarbons. The particulate phase contains clusters of respirable inorganic particles made mostly of carbon. This paper will address the health hazards, as we know them today, of the major components of the particulate phase in the exhaust of diesel engines. It will briefly examine the operational factors of the diesel engine as it applies to particulate emissions. Longitudinal studies of occupationally exposed miners are needed with documentation of levels of exposure before a chronic effect of exposure can be determined. At this time, it is not possible to conclude from human studies the level of diesel exhaust exposure that results in the observed lung cancer risk.

Jan 1, 2001

By D. Richers

When modeling predictive pit lake chemistry, groundwater chemistry is integrated with the affected portions of the wall rock and chemistry of the lake in a complex series of mixing. Fractions of the solutions impinge upon fresh, unaltered or fractured and oxidized zones of the wall containing sulfide materials and/or soluble metal/metalloid salts. Changing conditions over the short term (biannually) and long term (decades) can drive reactions allowing for dissolution or precipitation of acid rock drainage and metal leaching (ARD/ML) constituents. Local zonal variations can result in a portion of the pit releasing materials into solution; whereas other portions of the lake might favor the formation of colloids or precipitants. The proportions and character of groundwater can drive the chemistry of the pit lake provided sufficient buffering capacity is available to temper the generation of ARD in the system. For sulfide-rich systems, reduction of oxygen by rapid inundation and consumption by sulfides is key to reducing the ARD/ML. This paper presents several models of a sulfide-rich wall rock system using a range of groundwater chemistries to show these constraints.

Jan 1, 2012

By Augustine O. Orumwense

Ball mills are commonly used for regrinding operations in the mineral processing industry. But, in recent times, efforts are being made at the introduction of stirred mills particularly for those instances where very fine grinding is required. Media type (steel shot, glass beads, alumina balls and crushed quartz), media size, mill speed and the number of passes required to obtained the target product size are studied. The product size and energy consumption are used in the evaluation of the test results. The grinding media size, shape, density, filling ratio, mill circumferential speed and grinding time play a distinct role in product size fineness.

Jan 1, 2005

By W. H. Langer

Large amounts of limestone fines coproduced during the processing of crushed limestone may be useful in the sequestration of carbon dioxide (CO2). Accelerated weathering of limestone (AWL) is proposed as a low-tech method to capture and sequester CO2 from fossil fuel-fired power plants and other point-sources such as cement manufacturing. AWL reactants are readily available, inexpensive, and environmentally benign. Waste CO2 is hydrated with water to produce carbonic acid, which then reacts with and is neutralized by limestone fines, thus converting CO2 gas to dissolved calcium bicarbonate. AWL waste products can be disposed of in the ocean. Feasibility requires access to an inexpensive source of limestone and to seawater, thus limiting AWL facilities within about 10 km of the coastline. The majority of U.S. coastal power generating facilities are within economical transport distance of limestone resources. AWL presents opportunities for collaborative efforts among the crushed stone industry, electrical utilities, cement manufactures, and research scientists.

Jan 1, 2009

By E. R. Bauer

Previous studies and research efforts have shown that noise-induced hearing loss (NIHL) is a problem in the U.S. mining industry. This is especially true in surface and underground coal and stone mining where large, noisy equipment predominate. Workers in coal preparation and stone processing plants have also been found to be subject to high sound levels that could potentially cause NIHL over prolonged periods of exposure. National Institute for Occupational Safety and Health (NIOSH) researchers have been conducting a cross-sectional survey of equipment noise and worker noise exposures in the mining industry to estimate the potential for NIHL within the mining community. One commodity recently surveyed was the extraction of sand and gravel from surface pits and by river dredging. Little is known about the noise environment and worker exposures in these environments, where processing and mining equipment similar to coal and stone are employed. To address the potential for NIHL in the sand and gravel industry, sound levels on and around the dredges and processing equipment were recorded to identify areas of high noise levels. Full-shift worker dosimetry, in conjunction with task observations, was documented to determine the relationship between exposure and source. This paper presents research examining noise on dredges, in several surface mine sand and gravel operations and in the processing facilities. The locations where workers are likely to be overexposed and were found to be most susceptible to noise overexposures are reported. Results indicate that there are areas on the dredges (crane, suction pumps, and diesel engines) where sound levels greater than 90 dB(A) are present. In addition, crushers and screens used in the processing of the sand and gravel also generate sound levels greater than 90 dB(A). Although no surveyed worker exceeded the Mine Safety and Health Administration (MSHA) Permissible Exposure Level (PEL) of 90 dB(A) TWA8, laborers, mechanics, oilers, helpers, pickers, and greasers are the workers likely to be exposed to hazardous sound levels and thus develop NIHL over time. Knowledge of the equipment noise, area sound levels, and worker dose levels is information that management and employees can use to reduce exposures. Exposures can be reduced in certain areas through administrative controls and through engineering controls applied to the noisiest equipment.

Jan 1, 2008

By Richard Addison

Introduction A staccato beat rings out across the Australian bush. The stamps are at work, slowly pulverizing gold-bearing ore for a patient, grizzled prospector. This is the State Battery near Marvel Loch, a tiny 22.6-t/d (25-stpd) capacity gold plant operated by the Western Australia government. It is one of many such plants located in remote corners of Western Australia and the Northern Territory. They are miniature custom mills operated for the benefit of prospectors and small mine operators. These state batteries are so called because they are operated by state governments and because the principal item of machinery in the plants are stamp batteries. They are fascinating anachronisms - throwbacks to times past, a century ago, to the hard and heady existence of gold rush days. Marvel Loch plant Typical of these operations, and perhaps a trifle more sophisticated than most, is the plant near Marvel Loch, a small center for mining and farming about 400 km (250 miles) due east of Perth. Marvel Loch. The name evokes visions of a pristine lake set in a cool, green, misty glen of the Scottish highlands. Actually, it is probably a hot, dry salt pan somewhere nearby. Just where the "loch" is difficult to discern. There is no sign of it on the map.

Jan 7, 1986

By G. G. Marino, J. W. Mahar

This paper provides an utierstanding of the betivior and potenttil damage of homes resulting from sag-type mine subsidence. This is done with extemive research of numerom case histories in Illinois collected by the authors. The howe response to substience-itiuced ground displacements are summarized and evaluuted. A damage level criteriu, specifically developed for residenttil structures, is presented based primarily on repair costs. Damage levels and the associated subsidence profile characteristics for each case history are compared.

Jan 9, 1985

By S. Shaw

There is an increasing requirement for mines to meet a certain minimum criteria for sustainability within the context of the physical environment, ecosystem and socio-economic system in which they are located. The mining industry has wrestled to develop methods for assessing the ‘sustainability’ value of a mining project and indicators of ‘sustainability success’. A methodology for the evaluation of sustainability of a mining project using the Multiple Accounts Analysis (MAA) system was developed. The MAA is a platform for engagement of stakeholders and for the assessment of site-specific alternatives based on both qualitative and quantitative indicators of success.

Jan 1, 2004

By C. G. Buttleman, W. C. Brice

In Minnesota, reclamation of active aggregate mining sites is primarily regulated through local permits issued at the county, township, or municipality. However, for abandoned or depleted aggregate mining sites, a responsible party for reclamation is often no longer available. Since 1995, the Minnesota Department of Natural Resources has reclaimed several abandoned aggregate sites using innovative public/private partnerships and emphasizing native plant materials. The purpose of these projects is to demonstrate cost effective reclamation methods that can be utilized by both aggregate operators and local government and to promote mine planning and resource identification as it relates to reclamation.

Jan 1, 2000

By H. Y. Sohn, R. D. Hagni, M. K. Kojo

Reflected light microscopy was used to study the mineralogy and textures of experimental reactions of a nickel concentrate with a slag. Such an interaction is an important step in the bath smelting of nickel sulfide concentrate. Concentrate particles in the central portions of the pellets are rounded and develop vermicular SO2 gas porosity. In the outer portions of the pellets, the original minerals of the concentrate, pyrrhotite, pentlandite, pyrite, chalcopyrite, and violarite have agglomerated and reacted to form two intergrown phases: 1) pyrrhotite solid solution (Fe0.75Ni0.18Cu0.01S) and pentlandite solid solution (Fe0.58Ni0.51Cu0.03S). Magnetite formed euhedral crystals, skeletal crystals, and dendrites at the margins of the matte. Prismatic ferrohypersthene and octahedral Mg-Al-Fe spinel crystals and dendrites are present in the glassy slag.

Jan 1, 2001