Search Documents

By R. Hogg

Sedimentation in highly flocculated suspensions of fine particles such as clays occurs through individual settling units (flocs) which have very open structures and correspondingly low density -typically less than 5% solids by volume. It follows that such settling processes rapidly lead to the build-up of a bed of flocs which are essentially close-packed, with inter-floc porosity of perhaps 50%, but with an overall solids content of no more than about 2-3 percent by volume. An important consequence is that the thickening process is dominated by the consolidation of this bed rather than by simple settling of the individual flocs. Experimental measurements of sediment consolidation in flocculated clay suspensions indicate that for a given system, consolidation rates are essentially determined by solids concentration and can be evaluated using the classical Kynch treatment. However, these rates are strongly dependent on the physical as well as chemical conditions of the flocculation process. Furthermore the extent to which gravity consolidation proceeds depends on the total weight of sediment (i.e. on both height and solids concentration). The implications with respect to thickener operation and the requirements for laboratory testing for thickener design are discussed.

Jan 1, 1992

This paper investigates the effects of solids concentration and the addition of Dispersant S40 on the flowability of original and ground limestone slurries. A rotational viscometer with a concentric cylinder geometry and a controlled-stress rheometer with a cone-and-plate geometry were used to characterize the rheological behaviors of limestone slurries. The rheological behavior of original limestone slurries (<100 µm) is transformed through different types of flows with increasing solids concentration. The use of Dispersant S40 can improve the slurry flowability by decreasing viscosity and eliminating Casson yield stress. It is therefore used as a grinding aid for the wet ultrafine grinding of limestone. The rheological behaviors of ground limestone slurries vary with grinding from a starting dilatant flow-ability to a resulting pseudoplastic one with an evident Casson yield stress in combination with a thixotropic character. The appearance of pseudoplastic flowability combining thixotropy is related to the fineness of a ground product and its specific surface area, which are both correlated to solids concentration and the additive amount of Dispersant S40. In addition, the accurate rheological characterization of time-dependent fluids is dependent on the instruments used and operation conditions.

Jan 1, 2007

By William K. Brown

Are the results of an exploration program worth the cost? This is a question I suspect many of you are familiar with and, theoretically at least, it is an easy question to answer. The answer, of course, lies in comparing the future earnings stream the program is expected to generate, to the present value of the cost of carrying it out. While historical costs can be determined without much difficulty, estimating the value of a future earnings stream involves all sorts of assumptions regarding future costs, metal prices, inflation rates and an appropriate discount factor; and in the context in which the question arises, requires additional assumptions about mineral deposits which have yet to be discovered. As a practical matter, this kind of approach isn&apos;t likely to produce a very convincing answer; certainly not one convincing enough to satisfy a skeptical audience; nor one likely to temper the illusions of recent converts to mineral exploration, who are convinced that if enough money is spent, profitable discoveries will inevitably follow. Within broad limits, however, I believe it is possible to analyze the costs and results of gold exploration in the U.S.A. over the past 20 odd years in a useful manner. And while such an analysis is imperfect, it will provide some insight into this fascinating subject.

Jan 1, 1983

By R. Hogg, P. Bunnaul

Sedimentation in highly, flocculated suspensions of fine particles, such as clays, occurs through individual settling units (flocs) that have very open structures and correspondingly low densities (typically less than 5% solids by volume). Such settling processes rapidly lead to the buildup of a bed of flocs that are essentially close-packed, with an inter-floc porosity of perhaps 50%. However, the overall solids content is no more than about 2% to 3% by volume. Consequently, the thickening process is dominated by the bed consolidation rather than by the simple settling of the individual flocs. Experimental measurements of sediment consolidation in flocculated clay suspensions indicate, for a given system, that consolidation rates are essentially determined by the solids concentration and can be evaluated using the classical Kynch treatment. However, these rates are strongly dependent on the physical, as well as the chemical, conditions of the flocculation process. Furthermore, the extent to which gravity consolidation proceeds depends on the total weight of the sediment (i.e., on the bed height and the solids concentration). The implications with respect to thickener operation and the requirements for the laboratory testing for thickener design are discussed.

Jan 1, 1993

By W. Blake, J. Whyatt

Sixty years of rock bursting in the Coeur d&apos;Alene district has taught painful lessons and led to a number of practical advances in controlling rock-burst hazards. This paper summarizes these lessons, concentrating on practical measures that have been successfully adopted to reduce hazards. These lessons are explained in the context of district mining history and current understanding of rock-burst phenomena. Overall, the paper provides the practicing mine engineer with an appreciation of rock-burst hazards and an overview of practical measures that can be used to control these hazards in the context of Coeur d&apos;Alene district experience.

Jan 1, 2003

By G. Plenge, M. Diaz

Silver-bearing, bulk sulfide concentrates from several Peruvian mines were autoclaved in a l9-L (5gal) laboratory autoclave in Lima, Peru. Cyanidation of autoclaved concentrates, following a hot lime jarosite destruction step, extracted more than 98% of the silver and more than 95% of the gold. Autoclave operating parameters, such as time, temperature, pulp density and autoclaved solids recycle, were investigated and reaction rates determined. The problems of excessive heat generation, silver solubility during autoclaving and formation of pellets containing unreacted sulfides were addressed. The data presented will be used to design a continuous autoclave pilot plant to provide reliable scale-up data for a 50 to 100 t/d (55 to 110 stpd) facility.

Jan 1, 1994

By T. V. Johnson

The microstructural relationships in dolomitic fluxed taconite pellets were studied. The influence of basicity (in the range 0.75 to 2.1) and firing temperature (to 1340°C) on the grain structure, macrostructure, and mineralogical phase relationships are described. Extensive slag bonding of hematite grains begins at temperatures between 1220 and 1230°C, and results in fundamental changes in grain structure. Successive temperature increases result in little change in grain structure until 1340°C, when extensive coalescence of the hematite grains begins.&apos; Increasing flux additions have little effect on grain structure but greatly influence pore character. The compressive strength decreases with increasing flux addition, increases with increasing firing temperature, and is related to the macrostructure of the pellet. The compositions of the slag phases are represented on the CaO-Fe2O3-SiO2 phase diagram, and the compositional path of slag development is described.

Jan 1, 1980

By Dongjie Zhang, Zeyu Liu, Shuxin Liu, Yang Liu

Lateral pressure provided by caving rocks plays an important role in keeping the stability of the sidewall rock mass and controlling the rock movement. Taking Xilinhot Fluorite Mine as an engineering background, we studied the control mechanism of the granular media lateral pressure on the rock movement by combining physical experiments, theoretical analysis, and field monitoring. The results indicated that with the increase of the granular media depth, the lateral pressure provided by the static granular media presented two stages of rapid growth and slow growth. The lateral pressure on the footwall was negatively correlated with the dip angle of the orebody, and the lateral pressure on the hanging wall was positively correlated with the dip angle of the orebody. Ore drawing only caused the granular media lateral pressure near the drawing point to decrease. As the granular media moved, the granular media lateral pressure outside the pressure reduction area further increased, and this part of the granular media would play a key role in limiting surface rock movement. On this basis, the improved calculation formula of GLMP was given, which could be better applied to calculate the GLMP and critical granular media column with different dip angles. The action mechanism of the GLMP in the control of the surface rock movement was clarified. The granular body in the collapse pit was mainly composed of three parts: the bottom loose granular media column, the middle compaction granular media column, and the upper critical granular media column. The critical granular media column was the most important area to control surface subsidence and rock movement. Finally, through field practice, after effective filling of the collapse pit, the surface vertical displacement of the hanging wall and footwall was decreased by 56.8% and 55.6%, respectively, and the control effect of surface rock movement was remarkable.

Sep 18, 2023

By A. P. Cook

Methane drainage on a mine-wide scale is a relatively new technology to South African coal mines. Shallow seams and apparently low methane contents have been assumed to result in less methane problems than experienced in other countries. The introduction of deeper mines however, has now resulted in methane drainage taking on a higher priority. Methane contents in the region of 12 m3\t have resulted in one colliery introducing drainage as a ventilation support. Although a low seam permeability initially indicated reduced potential for drainage, early borehole flows of 90 m3\m\year have since increased to 450 m3\m\year. Rapid inflow of methane into goafs and sealed areas from seams surrounding the main production seam at another colliery have warranted extensive evaluation of the methane properties of these seams with the projected introduction of predrainage from surface. Methane pressures in excess of 1000 kPa and contents in the region of 10 m3\t again give methane volumes suitable for drainage. Coal seam drainage ahead of mining is becoming more significant and is likely to see an increase in the near future. INTRODUCTION Methane gas is an everpresent hazard associated with underground coal mining. Safe working levels of methane in the mine atmosphere are normally maintained by ventilation practises, ensuring sufficient dilution of the gas. However in some cases the ventilation must be assisted by methane drainage, either from the mined seam, or from adjacent seams and strata, or from goafed areas. South African collieries have practised only limited methane drainage until now. Relatively shallow mining depths, and apparently low in-seam methane contents have been assumed to result in fewer problems with methane than are the normal for other countries. This is now being shown to not necessarily be the situation. Work carried out by the Coal Mining division of COMRO (Cook and Erwee, 1991) indicates South African production coal seams have very similar methane retention properties to those of coals in other countries, with seam gas contents of up to 12 m3/t. This awareness, as well as greater mining depths, and higher degrees of mechanisation, has resulted in higher priority being given to methane emission problems throughout the industry. Increased levels of safety, as well as possible commercial applications, are the main reasons for the interest now being shown in methane drainage. Not only is there possible applications in the present production coalfields, but South Africa has vast areas of coal reserves which are presently non-mineable, now being seen as possible alternative energy sources. Limited methane drainage is practised within the industry, but only on collieries that have identified specific methane problems that can be alleviated by drainage. Historically this has been restricted to surface drainage of longwall goafs, reducing emissions onto the faces. More recently, horizontal in-seam holes have been drilled, until now for bord and pillar sections, but the results are being evaluated for later application to shortwall faces. Adjacent seams pose problems at some sites and vertical and cross measure boreholes are now being considered.

Jan 1, 1993

By D. H. Y. Tang, S. S. Peng

Three-dimensional finite element modeling (3-D FEM) was performed to analyze the safety factors of stump pillars, 5.5 m x 5.5 m, under a cover of 63 m using the Modified Drucker-Prager Theory. The results showed that they were safe. This was substantiated by underground observations. But the safety factors predicted by three commonly used pillar design formulae showed otherwise. This paper discusses the modeling details and analyzes the difference between 3-D FEM method and traditional pillar design formulae.

Jan 1, 1987

By M. Elzeky, A. Attia

The effects of bacterial adaptation and partial replacement of leaching solution on the rate and extent of bioleaching reactions of a complex sulfidic gold ore were investigated. The ore was first concentrated by bulk sulfide flotation and the sulfide concentrate was treated by bioleaching using T. Ferrooxidans bacteria. The residues from bioleaching were treated by cyanidation to extract the gold and silver. Bacterial adaptation before bioleaching significantly increased the rate and extent of bioleaching reactions. Similarly, the daily partial replacement of leaching liquor enhanced to a great extent the leaching rate and in some cases up to ten fold increase was observed. Both bacterial adaptation and solution replacement increased the gold recovery by about 2-fold and that of silver by about 1.3-fold. In this work more than 95% of the gold and more than 98% of the silver could be recovered from the sulfidic gold ore, when bioleaching was used ahead of cyanidation compared with 18.3% and 52.3% by direct cyanidation.

Jan 1, 1989

By Gabriel E. Zárate, Juan C. Guzmán

In Chile there are significant amounts of gold in flotation tailings that could be recovered, being heap leaching the most promising alternative. In order to determine the feasibility of treating these tailings by this method, a detailed study is carried out using 4 representative samples. After defining the best conditions an economic evaluation is done for a plant treating 200 tpd, sensibilizing with respect to parameters such us gold price, tailing grade and capital costs. The results show that it is technically feasible treat these gold tailings by heap leaching with gold extractions over 70 %. It is also economically feasible for gold grades higher than 0.5 g/t and gold prices over 350 US/oz.

Jan 1, 1987

By J. M. Wempen

Booster fans in underground coal mines are often located using the concept of a neutral point. Normally, intake airways are maintained at higher absolute pressure than return airways; therefore, air leaks from intake to return. By adding a significant pressure force to a region of a ventilation system, booster fans installed in a return airway can increase the pressure in the return so that air leaks from return to intake. This is commonly referred to as recirculation. The neutral point occurs at the location in the system where the pressure difference between [ ] the intake and the return airway is zero. At this point, there is no leakage or recirculation. Ideally, placing a booster fan near the neutral point minimizes leakage and recirculation. However, in practice, the position of the neutral point is not static and it changes as the ventilation system parameters change. Booster fans have the potential to increase the capacity and efficiency of coal mine ventilation systems. However, these fans add a significant pressure source to ventilation systems and can create areas where the pressure in the intake is less than the pressure in the return causing recirculation. In systems with multiple booster fans, there may be multiple recirculation paths and, as the capacity of these fans increases, recirculation is more likely to occur.

Jan 1, 2012

By S. K. Oraee

Most management decisions at all levels of the organization are as directly or indirectly depends on the circumstance of future. With regard to predict the future events in the process of decision-making plays a main role, therefore, forecasting is very important for every organizations and institutions. There is a variety of methods to predict time series. In general, these techniques can be divided as following: statistical, artificial intelligence and analytical techniques. Two of the most common methods for time series prediction is autoregressive integrated moving average (ARIMA) and artificial neural network (ANN) methods, these methods are the subset of statistical and artificial intelligence techniques respectively. In this paper, a hybrid model of ARIMA and ANN models are employed to predict the number of fatal injuries in the USA underground coal mines. This research showed the result of hybrid model is better than split model.

Jan 1, 2011

With the rapidly growing use of hydraulics in mining equipment, maintenance personnel should be familiar with the various components in hydraulic systems. Hydraulic systems do wear out - the fluids they transport are hot and turbulent, the equipment they power often imposes tremendous pressure pulsations and bending stresses, and the working environment is harsh. Therefore, even though hydraulic hoses are made of remarkably trouble-free components, they do need to be replaced periodically. There must be coupling methods that allow hoses to be replaced without disturbing other components. Couplings must also provide a variety of leak-resistant connections between hoses and other components in the hydraulic circuitry. Threaded Connection and Seals Hydraulic coupling thread ends and sealing arrangements are standardized, with many types available. Their outward appearance varies, but coupling configurations are recognizable by examining threads and seals and comparing them to the examples provided here. Iron Pipe Thread There are two kinds of iron pipe threads normally used in mining equipment circuitry - National Pipe Tapered Thread for Fuels (NPTF) and National Pipe Straight Thread Mechanical Joint (NPSM). The NPTF seal is the engagement of the coupling threads, called thread interference. When tightened, the tapered thread of the male fitting binds into that tapered thread of the female fitting to form a relatively leakproof seal (Fig. 1). In the NPSM seal, there is a 30° angle seat machined into the end of the male NPTF fitting. This seat engages with a mating 30° angle cone on the inside of the female fitting. Female NPSM fittings have straight threads, as opposed to the tapered threads of the NPTF fittings. However, most NPTF solid male fittings also have a 30° angle seat enabling them to be used with NPSM female fittings (Fig. 2). JIC and SAE Fittings Joint Industry Conference (JIC) and Society of Automotive Engineers (SAE) seals are formed by joining two mating, conical metal surfaces. The coupling threads are used to bring and hold these surfaces together to form a leak-resistant seal. A JIC connection is a solid male threaded end, with a 37° machined male nose, mating with a 37° female flare seat. When connected, the mating surfaces are held together by the threads, but the threads do not form the seal. The female seat is created by flaring a tube end or machining the interior surface of a stem to 37°. A female JIC has a swivel nut, allowing the sealing surfaces to be joined together without twisting a hose or twisting the seats against each other (Fig. 3). JIC couplings are frequently used on low, medium, or high pressure hydraulic circuits on mining equipment and machinery. The SAE connection is similar in appearance and sealing characteristics to the JIC system, except the angle of the machined male nose and female flare seat is 45° (Fig. 4). "O" Ring Fittings Seals for "O" ring fittings are formed by compressing an "O" ring against an exposed machined surface on a mounting block or hydraulic component part. The "O" ring must be compatible with the type of hydraulic fluid used (Fig. 5). An "O" ring boss connection is made of a male straight thread

Jan 10, 1983

By Miguel Carrera, Jose Arnal, Julian Ortiz, Maarten Haest, Fouad Faraj

ShovelSense is a complete solution for bulk ore sorting at the mine face that combines robust shovel bucket mounted X-ray fluorescence sensors, with real-time material classification, fleet management integration and supporting cloud-based data infrastructure, to ensure each truck always goes to the right destination. Correct truck destinations are a challenge in many current mining settings because the material classification of a truck, which is the key input into the truck destination, is often based on estimates at block resolution (~20x20x15m), with limited adjustment for blast movement and mixing. In this contribution, we present a geostatistical, data driven approach to estimate the potential value of bulk ore sorting at the mine-face for seven open pit mines. The approach is premised on the assumption that truck loads within blocks follow a simple gamma distribution. Standard ore control data from the seven mines have been used to estimate the potential bulk sorting value at these operations and ShovelSense-integrated dispatch datasets have been used to validate these estimates for specific benches on which ShovelSense operated. ShovelSense results validate the ore control data-based value predictions and show how at mine-face bulk ore sorting value varies between distinct deposit types. In general, deposit types that have higher bulk ore grade contrasts, display more potential ShovelSense value. The manuscript concludes with the limitations and opportunities of applying the proposed value estimation approach to evaluate at mine-face bulk ore sorting opportunities for open pit operations.

Jun 25, 2023

By Danu Putra, Budi Sulistianto, Tri Karian, Mohammad Nur Heriawan

Stope layout optimization is an important feature of underground mining that maximizes the economic value of the project while taking mining limits into account. The large number of parameters and constraints makes it difficult to obtain the optimum condition. Several algorithms have been created to address these problems using a variety of methods. However, the circulating method has not explicitly included stope dimension stability analysis, resulting in a solution that is not stability-proven, which can result in a suboptimal solution. This study integrates the Mathews stability graph into the stope optimization algorithm so that the optimized stope layout considers stability conditions directly through an assessment of the available geomechanical data within the block model. The proposed algorithm is validated through a case study of a synthetic block model created by considering variations in grade and the geomechanical conditions of the rock. Furthermore, several scenarios are created to compare the performance of the algorithm that applies variations in stope sizes with the common case study of stope sizes that remain fixed. A more detailed assessment is also conducted on each final stope layout wall to ensure the successful application of stability analysis in the proposed algorithm through back analysis on the Mathews stability graph. The optimization results show that all walls in the final stope layout fall into the stable condition. Also, the proposed algorithm is also capable of maintaining the project’s economic value. Ultimately, the proposed algorithm can be deemed applicable and suitable for use in the initial stages of mining as a comprehensive assessment of the optimal stope layout, taking into account the stability conditions of the stope.

May 22, 2024

By Ning Liu, Di Yin, Xuming Wang, Yongqiang Lu, Jan D. Miller

Air-sparged hydrocyclone (ASH) flotation technology has been evaluated for phosphate recovery from the central Florida phosphate deposits. As expected, it was demonstrated in pilot-plant tests that the ASH system has a specific capacity about 50-100 times higher than that of a traditional flotation cell. In the case of fatty acid flotation, single-stage ASH flotation produced a recovery of 75-77% in a rougher concentrate containing 24% P2O5 In reverse flotation with amine, the single- stage ASH system produced a phosphate recovery of 98% in a cleaner concentrate containing 31% P2O5. These results are comparable with those obtained at plant operations in the Florida phosphate industry. Based on these pilot-plant results, the effects of process variables are discussed in terms of separation efficiency. Subsequently, a 6-inch ASH system was fabricated and tested in a central Florida phosphate plant for reverse flotation in the amine flotation circuit. The high capacity of the ASH system was again demonstrated for the 6-inch ASH system. A single-stage phosphate recovery of 91% was achieved with a concentrate grade of 30% P205. During plant tests, it was established that porous tube plugging, the most significant engineering problem identified, was due to the poor quality of the plant water. Possible solutions to this problem are discussed.

Jan 1, 1999

By Thomas Gregor, Brian Garrod

As the popularity of precast concrete segmental linings for tunnels is growing in North America, some problems related to grouting of, and near, these linings are starting to appear. The installation of a segmental lining behind a TBM requires that the annular space around the lining be quickly filled with grout to prevent collapse of the ground. In practice, the filling of the annulus is frequently delayed and takes place a distance behind the machine typically via grout ports centrally located in the segments. If partial collapse of the annulus has occurred, it may become necessary to use higher grouting pressures in an attempt to distribute the grout. There have been several occasions where these increased pressures have caused damage to the tunnel linings. Similarly, compaction grouting adjacent to a tunnel lining can cause damage. This paper quantifies the effects of such grouting on a typical precast lining.

Jan 1, 2005

By W. R. Reed, D. E. Pollock, T. W. Beck, J. A. Organiscak, J. D. Potts

In underground continuous mining operations, ventilation, water sprays and machine-mounted flooded-bed scrubbers are the primary means of controlling respirable dust exposures at the working face. Changes in mining arrangements — such as face ventilation configuration, orientation of crosscuts mined in relation to the section ventilation and equipment operator positioning — can have impacts on the ability of dust controls to reduce occupational respirable dust exposures. This study reports and analyzes dust concentrations measured by the Pittsburgh Mining Research Division for remotecontrolled continuous mining machine operators as well as haulage operators at 10 U.S. underground mines. The results of these respirable dust surveys show that continuous miner exposures varied little with depth of cut but are significantly higher with exhaust ventilation. Haulage operators experienced elevated concentrations with blowing face ventilation. Elevated dust concentrations were observed for both continuous miner operators and haulage operators when working in crosscuts driven into or counter to the section airflow. Individual cuts are highlighted to demonstrate instances of minimal and excessive dust exposures attributable to particular mining configurations. These findings form the basis for recommendations for lowering face worker respirable dust exposures.

Jan 1, 2016