Search Documents

By A. J. Plumpton

Centrifugal air classification and li-quid-phase sedimentation are the principal methods of industrially sizing materials of dimensions smaller than those handled by screens. Increasing application of materials such as composites and high performance ceramics has furthered the need for closely-sized, fine, industrial mineral and synthetic products of controlled properties. Sedimentation can be used to separate very small sized particles but introduces problems of liquid-solid separation, de-agglomeration and drying. Some of the advantages and limitations of centrifugal air classification will be discussed and laboratory and plant measurements using centrifugal machines will be presented to support the discussion.

Jan 1, 1990

By M. Ramachandran, R. G. Reddy

"A direct route for the reduction of magnesium oxide to magnesium using thermal plasma processing, with methane as the reducing gas, has been systematically evaluated. A feasibility study of the reduction reaction has been performed on the MgO-CH4 system at different methane concentrations and temperatures. The effects of changes in the key process parameters, such as the oxide-to-methane ratio and plasma power, on the yield of magnesium have been systematically evaluated. A maximum yield of about 61 mol% Mg was obtained using power of 20.0 kW and a molar ratio of MgO:CH4=1:1. Phase, morphological, elemental and binding energy analyses were performed on the product powders to understand the reduction reaction. Surface oxidation was observed in smaller magnesium particles in all the experiments, while the in-situ sintering of magnesium rods was observed at a molar ratio of MgO:CH4=1:1.5. Magnesium carbide (Mg2C3) was observed in the product, and its mechanism of formation is proposed using phase equilibrium data and a predominance diagram.IntroductionMagnesium has an excellent combination of low density and high strength. These properties have increased worldwide demand for and use of magnesium. Two major processes are used in the commercial synthesis of magnesium metal. The first method is electrolytic reduction and the second is thermal reduction using Pidgeon process. These processes can be classified as traditional techniques, but there are numerous emerging technologies that aim at reducing the production cost of Mg, its environmental impact and energy consumption. Thermal plasma processing is one emerging technique that has great potential in all the abovementioned key areas of magnesium production.Traditional reduction techniques. Two major reduction techniques, namely electrolytic and thermal reduction, have been used in the commercial production of magnesium. Electrolytic reduction is typically carried out in electrolytic cells from magnesium chloride (obtained from seawater or well and lake brines) (Tripp, 2009). The following simplified reaction shows the reduction of magnesium chloride to liquid magnesium and chlorine gas:"

Jan 1, 2015

By S. Al-Thyabat

Conditioning of flotation feed is an important prerequisite for efficient flotation. This process depends on parameters such as conditioning time, slurry concentration and slurry pH. The objective of this paper is to optimize the conditioning process for the flotation feed. This was achieved by first conducting preliminary experiments at constant slurry pH to determine the significant ranges of slurry concentration and conditioning time. Then, factorial experimental design (32 experiments) was used to investigate the significance of the above parameters and their interactions on flotation recovery and grade. Statistical analyses using ANOVA approach showed that flotation recovery (R) and concentrate grade (g) were affected by feed conditioning. It was found that concentrate grade was linearly proportional to the slurry concentration and conditioning time, while flotation recovery was exponentially proportional to the conditioning parameters. A contour plot of the flotation response (recovery and grade) against conditioning parameters showed that the optimum operating parameters for flotation feed conditioning was a conditioning time of 1.5 to 2 minutes and a slurry conentration of 55% to 60%.

Jan 1, 2008

By H. Dr. Boldt, J. Dr. Henneke

PREFACE In German coal mines the application of tunnel boring machines has become a very effective and economic technique for major development works. After initial trials around 1970 the breakthrough was reached by driving 13 km of road ways on Rheinland and Friedrich Heinrich collieries, using a DEMAG tunnel boring machine of 6 m diameter. INTRODUCTION The coal mines of Rheinland and Friedrich Heinrich are to be found in the West of the Ruhr Area, the largest coal mining area in the Federal Republic of Germany (Table 1). They form part of the Ruhrkohle company. Rheinland coal mines produces 41000 to 43000 t of run-of-mine coal every day, of which 20500 t are usable coal. Friedrich Heinrich has a daily production of 17000 t of run-of-mine coal, 9000 t of which are usable. The coal is worked at depths of 600 to 1100 m in seams 0.6 to 3.0 m thick. The method of mining is longwall, and the machines used are ploughs and shearer loaders. From 1973 to 1980 a programme was put into operation in these two mines to develop and open up the coal field on the 885 m level. A total tunnel length of 20 km was to be driven. After thorough investigations it was decided to employ a full-face tunnel boring machine for

Jan 1, 1981

By Kerry Gee, Gary Colgan, James Fricke

Introduction Elevated zinc concentrations are observed in groundwater within alluvium adjacent to Silver Creek east of Park City, Utah. The study area is located in a small valley one and one-half miles northeast of Park City, Utah in Summit County, Utah (Figure 1). Although surface water concentrations in Silver Creek are typically less than 1 mg/l, groundwater concentrations have been measured as high as 85 mg/l in a near neutral pH environment. The elevated zinc concentrations in groundwater result from several factors including: (1) dissolution of zinc from tailings exposed at the surface and within the alluvium, (2) oxidizing conditions created by surface/ground-water exchange, and (3) ideal geochemical conditions for the dissolution of zinc-containing minerals. These ideal conditions include readily soluble minerals, available anions for complexation, and lack of available surface adsorption sites.

Jan 1, 2005

By S. Dessureault, Z. Gavelan

As globalization continues, sustainability and social responsibility has become essential in foreign mining investment. However this global trend and the increasing acceptability toward the globalization process, viability and sustainability are not always achieved. Viability and sustainability of mineral projects is dependant on the social and political environment of the region where the mining venture is located and is based on the interaction between the mining entrepreneurs, national-local government representatives, communities, grass-roots groups and independent civil organizations. These are the organizations, which play the acting roles on the viability of mining projects and are the main source of socio-political risks for the project. Throughout the decision-making process to invest in a mineral project, socio-political risks are quantified using a set of measurable variables. Nevertheless, these risk measures should be dependent on specific industries. Two mineral projects, even in the same mining district, may have significantly different political risk profiles based on their own socio-political variables. This paper describes a methodology that takes into account local social and political variables in defining a project-specific’s political risk profile. This contrasts with more typical political risk measures that focus on the country’s overall risk profile. Mining operations must operate on a local scale necessitating the development measure that considers more local variables.

Jan 1, 2004

By R. E. Snow

The analysis of ground water inflow and discharge from underground mines has received increased attention in recent years due to environmental issues which must be addressed under current state regulations for coal mining and processing operations. In particular, coal operators must assess the probable hydrologic consequences associated with mining activities, and must plan for mine water handling during operation and following completion of mining. The prediction of ground water inflow rates with future mine development allows preparation for potential operational problem and identification of inflow reduction methods. Similarly, evaluation of mine discharge rates is necessary to address potential long-term acid mine drainage (AND) concerns. As part of mine discharge analyses, methods. to control seepage and AMD can be considered. The objective of this paper is to discuss the practical applications of mine inflow and discharge analysis, describe the typical flow components, outline the procedures necessary to perform the analysis, and illustrate the modeling procedures and potential results of mine inflow and discharge predictions.

Jan 1, 1990

By V. K. Paruchuri, J. D. Miller, J. Nalaskowski

The phenomenon of surfactant adsorption at mineral surfaces is of significant importance in many particulate processes ranging from mineral flotation and enhanced oil recovery to pharmaceutics, paint technology and the casting of high quality ceramics. Stability of the dispersions is related not only to the amount of adsorbed surfactant but also to the structure of the adsorbed surfactant molecules at the interface. This structure greatly depends on the type of surfactant and the hydrophobicity or hydrophilicity of the surface. On hydrophobic surfaces surfactants adsorb regardless of surface charge by van der Waals/hydrophobic inter-actions with hydrocarbon chains accommodated at the surface. On the other hand, on hydrophilic surfaces the surfactants adsorb through electrostatic interactions with their polar moiety fixed at the surface. In the latter case, the electric charge of the surface and surfactant plays a crucial role in the surfactant adsorption process. The recently developed soft-contact Atomic Force Microscopy technique has revealed images of adsorbed surfactant structures at various interfaces. The adsorbed structures of a cationic surfactant (CTAB) and an anionic surfactant (SDS) are presented in this work for different concentrations at hydrophobic graphite and hydrophilic mica surfaces. Different types of micellar arrangements have been observed at these surfaces for surfactant concentrations around the critical micelle concentration. The structures are more ordered and well defined at the graphite surface than at the mica surface. These results have been correlated with the hydrophobicity of the surfaces as revealed by contact angle measurements.

Jan 1, 2001

By SANJIT KUMAR PAL, Sarvesh Kumar, Arindam Guha

The integrated geophysical study around pipe 1 and pipe 2 in Wjarakarur Kimberlite Field (WKF) assisted in comprehending the response of pipes. In the present study, we have attempted a combined analysis of very low-frequency electromagnetic (VLF-EM), electrical resistivity tomography (ERT), and magnetic methods to analyze the response from pipe 1 and pipe 2. A comparative analysis along all the profiles revealed the extension, depth, and geometry of the pipes. The results of VLF data and ERT data have been compared for two profiles of pipe 1 and pipe 2. Fraser-filtered grid map generated from all profiles of pipe 1 proficiently demarcated the trend of kimberlite pipe extension with high Fraser filter value associated with kimberlite. The ground-based magnetic data around pipe 1, pipe 2, and pipe 6 have been processed to analyze the magnetic behavior and subsurface structure based on the susceptibility contrasts. Analytical signal (AS) map revealed the extension of pipes, which was validated with the Fraser-filtered grid map. Analytical signal anomaly pattern reveals that pipe 1, pipe 2, and pipe 6 are trending in SW-NE, NE-SW, and NE-SW, respectively. Based on this study, the results indicate the conducting nature of pipe 1, whereas pipe 2 is resistive in nature. Further, the Euler deconvolution technique has been applied to calculate the possible depth of pipes from magnetic data. The comparisons of calculated depth ranges obtained from all geophysical techniques correlate well and validate the result (Table 1). The geological borehole data at pipe 1 and pipe 2 reported by the Geological Survey of India are well corroborated with our combined geophysical study.

Jan 17, 2024

When defining a ?megaproject,? one need only to look at Seattle, WA?s State Route 99 Alaskan Way Viaduct replacement project. This $3.1-billion project is one of the largest of its kind in the world, and includes the use of the world?s largest tunnel boring machine (TBM). However, for as large as the Alaskan Way project is ? especially given the size of the TBM being used ? there are several other megaprojects underway around the world. Each has its own challenges that require innovative design techniques and financing arrangements, as well as variations on established tunneling technologies. So it was that 266 tunneling and underground construction professionals ? owners, contractors and engineers ? convened in Seattle in November for the Cutting Edge Conference on Megaprojects. This was the second joint meeting between the Underground Construction Association of SME and the North American Tunneling Journal. The first joint conference took place in April 2012 in Miami, FL and attracted 238 attendees. A third joint conference, to be held in 2014, is in the planning stage. The key reason Seattle was chosen as the site of the megaprojects conference is the Alaskan Way Viaduct project. Before the conference began, many of the attendees were able to visit the project and get a close look at Bertha, the Hitachi Zosen earth pressure balance TBM that is boring the tunnel. In addition, the conference included an exhibit that attracted 20 industry suppliers, up from 10 the previous year in Miami. The 25 presentations during the two-day conference covered all aspects of the tunneling and underground construction of megaprojects. Topics included the Alaskan Way Viaduct project; considerations for procurement and contracting; political risk, financing and insurance; international megaprojects; risk and risk sharing and project delivery. Each session concluded with panel discussions.

Dec 1, 2013

By P. T. Bissert, T. J. Lutz, J. A. Yonkey, G. T. Homce

"Underground refuge alternatives (RAs) require an air source to supply breathable air to the occupants. This requires pressure relief valves (PRVs) to prevent unsafe pressures from building up within the RA. The Mine Safety and Health Administration (MSHA) mandates that PRVs prevent pressure from exceeding 1.25 kPa (0.18 psi or 5 in H2O), or as specified by the manufacturer, above mine atmospheric pressure when a fan or compressor is used for the air supply. Research to date by the National Institute for Occupational Safety and Health (NIOSH) suggests that the design and implementation of PRVs used in RAs has not yet had sufficient performance analysis or technical development. In response to this need, NIOSH tested a variety of PRVs using an instrumented test fixture consisting of data acquisition equipment, a centrifugal blower, ductwork, and various sensors to determine if subject PRVs meet the MSHA requirement. Relief pressures and flow characteristics including opening pressure and flow rate were measured for five different PRVs under a variety of conditions. Subject PRVs included two off-the-shelf modified check valves, two check valves used in MSHA-approved built-in-place (BIP) RAs, and a commercially available valve that was designed for a steel RA and is currently being used in some BIP RAs. The test results showed relief pressures ranging from 0.20 to 1.53 kPa (0.8 to 6.1 in H2O) and flow rates up to 19.3 m3/min (683 SCFM). INTRODUCTION The Mine Improvement and New Emergency Response Act of 2006 (MINER Act) was enacted in the wake of three mine explosions/fires that claimed 19 lives that year. Intended to help improve underground coal mine accident preparedness, the MINER Act includes provisions that target mine safety issues in areas such as emergency response planning, adoption of new technology, training and education, and mine safety standards enforcement [1]. Section 13 of the MINER Act specifically directed NIOSH to provide for research into the effectiveness and viability of refuge alternatives (RAs) for underground coal mines. This mandate culminated in the 2009 adoption of changes to 30 CFR mining health and safety regulations, requiring underground coal mines to provide mine emergency RAs and associated components, to provide a life-sustaining environment for persons trapped underground. Such RAs can be either self-contained mobile units or built-in-place (BIP) facilities. The regulatory changes also include provisions establishing requirements for Mine Safety and Health Administration (MSHA) approval of RAs and their components, and among these provisions are numerous criteria for providing a safe breathable atmosphere under positive pressure within the RAs. One specific criterion for maintaining a safe RA atmosphere requires the inclusion of an air pressure relief valve that will activate at a maximum of 1.25 kPa (0.18 psi or 5.0 in. H2O), or at a pressure above mine atmospheric pressure in the RA as specified by the manufacturer when the breathable air is supplied by a fan or compressor [2]."

Jan 1, 2017

The administration came on as a strong supporter of the mining industry in April of 1982 when President Reagan delivered his long-awaited minerals policy statement. He promised to reduce America's minerals vulnerability, and called for spending billions on meeting stockpile goals for strategic minerals, opening up federal lands for mineral exploration, elimination of barriers to deep sea mining, and regulatory relief. He defended the favorable tax incentives in the Economic Recovery Act as a stimulus to private research and development that would ensure the availability of materials essential to the nation's economy and national defense. But the administration just didn't seem to get anywhere. Congress, environmentalists, and even foreign governments fought White House-proposed legislation on all fronts, delivering the ultimate coup in forcing Environmental Protection Agency Administrator Anne Burford's resignation and the subsequent EPA staff house cleaning in early 1983. Anti-Reaganites scored victory after victory against Reagan's efforts to stimulate the minerals industry. Congress was stalemated on so many mining-related issues that not much was done either for or against the industry. And the US was not to get its way on the issue of sea mining either. Most of Reagan's mineral policy objectives failed to be met. Three months after the National Materials and Minerals Program Plan was presented and the Cabinet Council on Natural Resources and the Environment was made its coordinator, the head of the Cabinet Council James Watt blamed lack of progress in reviving the mining industry and creating a better strategic stockpile on the weak economy and the House of Representatives, which repeatedly thwarted efforts to open wilderness lands to mining. Congress The 97th Congress spent much of its time saying no in 1982-to the Reagan administration's deep cuts in energy and environment programs, to major changes in clean air and water laws, to oil and gas leasing in wilderness, and to killing the Department of Energy. Most of 1982 (and 1981) was spent in heated budget disputes. Some things that did not happen: • The administration and industry failed to get changes in controls of hazardous air pollutants and sulfur dioxide emissions that are implicated in the phenomenon known as acid rain. Industry had wanted to relax requirements for new industries building in clean air regions where the air act demands prevention of significant deterioration (PSD) of air quality, and to relax requirements tightening up the regulation of emissions of hazardous air pollutants. The air battle is expected to continue on five major fronts-acid rain, hazardous air pollutants, PSD, automobile pollution, and nonattainment. • Regulatory reform legislation to overhaul the way government carries out the law died a slow death last year. Business groups and the administration said federal agencies should be required to consider cost-effective measures of reaching regulatory objectives of protecting public health, safety, and the environment. Opponents, including environmentalists, feared such action would delay, weaken, or scuttle important regulations. • Congress turned thumbs down several times on proposals for oil and gas leasing in wilderness but could not agree on any new wilderness recommendations (see The Wilderness Battle). • Congress refused to open the door to the Reagan administration's plan to raise up to $4 billion a year from sales of federal lands. The administration identified surplus and excess federal lands, mostly obsolete buildings or isolated tracts of land, that could be sold by the General Services Administration (GSA) to help out the federal budget deficit. Congress took no action. Some things that did happen: • Congress extended the Defense Production Act (DPA) for six months through March 1983 without changing the 32-year-old law. That came after it failed to resolve sharp differences over proposals for critical minerals programs. Differences concerned both the amount of funds and the scope of programs that would be authorized under the DPA's Title III. Some proponents pressed for $5 billion in funding for loan guarantees or purchase commitments to spur domestic production of minerals such as cobalt. Other members of Congress wanted smaller amounts of funding, and the Reagan administration, until about November, had opposed any use of federal funds for strategic mineral programs. These measures were certain to come up again before the DPA extension expired in March. • House supporters of the Critical Materials Act of 1982 were unable to come up with the twothirds majority needed to pass the bill, so it died on the House floor in December. The bill proposed that a council be established with responsibility for coordinating federal materials research and development. The administration opposed the council creation contending that the Cabinet Council

Jan 5, 1983

By A. J. Hendron, J. E. Monsees

INTRODUCTION This paper is the outgrowth of work done by the authors to prepare the seismic design criteria for underground structures on the Southern California Rapid Transit District (SCRTD) Metro Rail Project. It is a follow-on to a similar paper presented at the October, 1984, ASCE National Convention (17). For design, the earthquake-induced distortions recommended herein are to be added to the normal static loading conditions for the underground structure. This design approach has been used by 18 section designers on the SCRTD Project. Preliminary results from two- and three-dimensional finite element solutions have partially verified the approach. Areas where additional research is needed for special cases are identified. EFFECTS OF EARTHQUAKE The effects of earthquakes on underground structures may be broadly grouped into two general classes -shaking and faulting. In response to earthquake motion of bedrock (shaking) , the soil transmits energy by waves. Seismologists identify various types of earthquake waves, but underground engineers are generally interested in the effects of transverse shear waves which produce a displacement of the ground transverse to the axis of wave propagation. The orientation of propagation is generally random with respect to any specific structure. Waves

Jan 1, 1985

By Jiaqi Jin, Jan D. Miller, Chen‑Luh Lin, Amanda N. Erskine, Shijie Wang

Recovery of metals from coarse ore particles is a great challenge for heap leaching operations of low-grade precious metal resources. Internal fractures of ore particles like micro-cracks can facilitate subsurface transportation of solution inside particles and leaching of valuable minerals. A plant-scale high-pressure grinding roll (HPGR) unit at Coeur Mining’s Rochester mine was operated at selected specific pressures to crush and prepare various products for crack analysis using high-resolution X-ray computed tomography (XCT). 3D shapes of cracks inside ore particles for selected size fractions reveal different damage mechanisms during HPGR crushing regarding particle size and crushing pressure. Close-to-surface cracks formed by abrasion were found in small 2.5 mm particles. Impact cracks with a high aspect ratio were found in particles of larger size and higher HPGR pressure. The volumetric percentage of internal fractures and the specific crack surface areas of selected ore particles are compared to give quantitative conclusions on particle damage by compression during HPGR crushing.

Apr 20, 2024

By Michael S. Kucker, Stuart Warren, Robert A. Robinson, Michael J. Lehnen, David McAllister

Geotechnical conditions exposed by the phased exploration programs have had a major impact on the selection of excavation and support methods, dewatering requirements, size of openings, vertical alignment, and estimated cost of construction for the Beacon Hill Tunnel and Station section of the “Link” Light Rail. Beacon Hill is comprised of a very complex glacial geology, including numerous slickensided fractures, injected sand dikes, and multiple perched groundwater levels as revealed by a phased boring program and exposed in a test shaft. The Geotechnical Baseline Report (GBR) presents this complex geology along with a “tool box” of alternative additional support systems to accommodate the varying ground conditions during construction of the station excavation. Additional explorations will also be accomplished during construction to further refine the geotechnical interpretations and provide an opportunity to use pro-active ground improvement techniques to optimize the station excavation and support requirements.

Jan 1, 2005

By Nikhil Dhawan, Shrey Agrawal

Feldspar, a low-alumina, and abundantly available aluminosilicate source, is explored in this study to extract aluminum and potassium values. The sample comprises lamellar layers of microcline and albite with quartz containing 17.4% Al2O3, 9.67% K2O, and 66.3% SiO2. Mechanical (milling) and thermal (alkali and acid baking) activation are investigated, followed by HCl leaching. The milling treatment up to 6 h is inefficient in phase dissociation and results in ~ 40% Al and K dissolution. The alkali thermal treatment yielded 80% Al and 71% K extraction. Direct precipitation of the dissolved Al and Si values yielded alumina purity of ~ 29%, and silica gelation separated SiO2 and improved alumina product (94% purity, 71% recovery). Acid baking yielded 98% pure alumina precipitate; however, Al and K extraction were limited to ~ 45% and 65%, respectively. The microwave-assisted alkali treatment was optimal with 800 W and 10 min processing conditions yielding 80% Al and 71% K recovery with 2.26 kWh/kg alumina of thermal energy consumption. The final product contains γ-alumina with a specific surface area of 87 m2/ g. Keywords Feldspar · Alumina · Potassium ·

May 18, 2022

By Sihua Lei, Hong Zhong, Shuai Wang, Yu Gan, Zhanfang Cao

High purity MgO is widely used in various fields as an important magnesiumcompound. The separation of Mg and Ca is of great importance for the preparation of high purity MgO from dolomite. In this study, the key effects of carbonization temperature and nano-calcium carbonate agglomeration on the separation mechanism of calcium and magnesium have been investigated. The results indicated that the reaction in the carbonization process was stepwise. Precise control of the carbonization temperature was essential for the formation of Mg(HCO3)2 due to its low reaction efficiency at lower temperatures or decomposition markedly at higher temperatures. Meanwhile, there was a common-ion effect in solutions containing Mg2+ and Ca2+. Nano-CaCO3 particles were formed during carbonization and agglomerated with the prolongation of static time. A product with a purity of 99.56% MgO and 0.16% CaO was obtained under the optimized conditions: ratio of liquid–solid 30 L/g, carbonization temperature 22–25 °C, carbonization time 1 h, and refining time 4 h. This work has important guiding significance for the preparation of high purity magnesium oxide from dolomite.

Apr 21, 2020

By Stephen M. Smading

The Jinping-II hydroelectric project in China features four parallel headrace tunnels approximately 18-km- (11-mile-) long. Two will be excavated by tunnel boring machines (TBM) and two by drill-and-blast. A nearby fifth tunnel is being excavated by a 7.2-m (23.6-ft) TBM to draw down ground water in advance of excavating the headrace tunnels. Unique onsite assembly of a 12.43-m (40.7-ft) main beam TBM and backup system was completed on Sept. 18, 2008 in the remote mountains of the Sichuan province. The equipment was assembled onsite, without previously having been assembled and tested in a factory, using a method called onsite first time assembly (OFTA). This paper addresses the following topics: ? Project description including geology and terrain. ? The decision process leading to onsite, first time assembly, the assembly process and logistics, and lessons learned. ? Design features of the TBM and backup system. ? Operational history from startup to the writing of this article.

Jan 1, 2009

By L. K. Marshall

Last month's engineering fundamentals article discussed some general considerations of underground mine ventilation. This month's article takes a look at auxiliary ventilation-brattice, fans, and ducting-in underground mines. The need for good, efficient auxiliary ventilation increases as mines get deeper and move farther from ventilation shafts. New mining methods and equipment resulted in faster work area advances, liberating more dust, gas, and heat. As a result, worker health and safety requirements in the face area have become more stringent. For all these reasons the safety and efficiency of any underground mine depends heavily on its auxiliary ventilation. The purpose of such ventilation is to supply sufficient quantities of clean air to the face of the drift and to maintain air quality within desired limits until expelled from the mine.

Jan 2, 1982

By T. A. E. Breen

A new high intensity grinding technology has been developed and is now being commercialized by Hicom International of Australia. This has led to the development and manufacture of Hicom 120 grinding mills which are now being sold internationally for a range of mining industry applications. The first commercial process application has been for the diamond sector, where the ability of the mill to remove host kimberlite rock by attritioning, with no damage to the thereby liberated diamonds, is seen to be a most beneficial attribute. There are, however, many other mineral industry applications for this mill. The design of the Hicom mill is unique. Based on a high speed centrifugal motion of the grinding chamber, very high power intensity is delivered to the grinding process. Most significantly, a high acceleration field, 50 times stronger than gravity is produced, creating very high power input per unit of mill volume, and exceptionally fast particle breakage rates, typically 50 - 100 times greater than those in conventional tumbling mills. A mill developing such forces has significant implications to comminution technology and practice.

Jan 1, 1999