Search Documents

By A. John R. Hart

INTRODUCTION The use of precast concrete tunnel liners as the initial and final tunnel lining for transit systems has been a major consideration of designers for over three decades. The obvious benefit of building a tunnel that requires only a single pass in constructing the structural lining can provide the opportunity of saving both time and cost. This technique has had worldwide application in transit systems in London, Munich, Hong Kong, Toronto to name a few. In the United States precast liners were evaluated for use on the BART System in San Francisco in the early 1960's but did not provide sufficient confidence in the sealing capabilities available at that time. In 1976 it was decided to call for bids on the Lexington Market Tunnels in Baltimore with a precast concrete liner alternative for one of the tunnel drives. This option was selected by the owner and UMTA to provide a study evaluation for the benefit of the industry. HISTORY In 1983 Washington Metropolitan Area Transit Authority began calling for a series of bids on soft ground tunnels on the Green Line, which included the option of using precast concrete tunnel liners first as an alternative to fabricated steel tunnel liners. Over the years following, the precast concrete tunnel liners have become known as the conventional tunnelling system and, in the last year,

Jan 1, 1989

By Chandra S. Brahma

INTRODUCTION The process of predicting ground condition with exactitude and of ascertaining appropriate ground control measures is pertinent to each and every excavation. The control and support of soil and/ or rock during and subsequent to excavation is essential in order to overcome or avoid excessive movement, maintain stability or preserve integrity of the excavation, handle or prevent excessive water intrusion or hydrostatic pressure build up, and produce an excavation that is safe and suitable for its intended purpose. The design of support systems has primarily been, until recently, based upon experience and empirical or semiempirical guidelines, which do not lend themselves to thorough analytical calculations giving rise to the desired degree of confidence in design of such systems and consequently, several, if not a majority of support systems, no doubt, are overdesigned. The primary objective of this paper is, therefore, to briefly outline engineering considerations leading towards the design of ground control systems for near vertical excavations extending to shallow depths in metamorphic rock formations. Several engineering considerations including the selection of temporary support systems, technical aspects of design, and the sequence as well as details of construction, are briefly outlined. Since excavation for mining purposes or for civil engineering works frequently must pass through highly decomposed, weathered, fractured, sheared or faulted rock masses, the problem of general interest in underground engineering involving analysis of the stability or the support requirement for an excavation in an

Jan 1, 1981

By John R. Wright

This paper reviews the increased use of mechanization in order to develop lateral headings efficiently and economically. Particular emphasis is placed on the role of the Electric-Hydraulic Drill Jumbo in achieving this goal. Also, the use of modified mining equipment to suit various operating conditions is discussed.

Jan 1, 1981

By Gunther Riedmuller, Johann Golser, Peter Schubert

The paper deals with the experience of the authors to cope with tunnel projects in heterogenous and weak rocks. The procedures applied to the investigation of such areas, the geotechnical assessment, the choice of tunnelling methods, the preparation of contract documents and the main features of NATM tunnelling to adapt to these conditions are outlined.

Jan 1, 1993

By Jerome C. Neyer

Within most of Canada and the northern third of the United States, the soils overlying bedrock are of glacial origin. Tunnelling in glacial soils presents numerous challenges to the contractor, including abrupt changes in soil type, boulders and glacial erratics, water bearing fine sands and silts, toxic or explosive gases, and glacial till. This paper examines the available techniques for geotechnical exploration in glacial soils; the relationship between subsurface conditions predicted by various techniques and conditions actually encountered during tunnel construction; and potential improvements in the planning and implementation of geotechnical explorations. Case histories of geotechnical exploration and tunnel construction in glacial soils are also reviewed.

Jan 1, 1985

By C. DeW. Van Siclen

A simple mathematical description of the settling behavior of monosized particle suspensions is derived by consideration of the physical processes involved, and applied to data recently published in this journal.

Jan 1, 1995

Because of the different types of reagents used for the flotation of sulfide and nonsulfide minerals, it is convenient to consider these two groups of ores separately. The metal sulfides and native metals are substantially all floatable with xanthate and similar collectors.

Jan 4, 1982

By John A. Shuster, Joseph A. Sopko

Construction of two shafts, as well as associated deep concrete structures, for a major storm sewer project in Milwaukee, Wisconsin required ground water control and temporary ground support to depths ranging from 19.2m to 55.0m. Lowering of the site ground water table eras not possible because of potential consequences for existing nearby structures. Construction entailed completion of two shaft collars into bedrock. In addition to the shafts, several adjacent connected. structures were completed. Ground freezing was selected to provide temporary ground support and ground water control for all excavations. The first application of using reinforced frozen earth was successfully incorporated on the project. The procedure enabled the contractor to create openings in excess of 9.1m in height, without bracing, through highly stressed frozen earth walls. Design features and construction procedures for completion of ground freezing and related excavation are reported.

Jan 1, 1989

By D. Zaharaki

The present experimental study underlines the advantages of factorial design in environmental, geotechnical and waste management experimentation. A typical case study regarding solidification of metallurgical wastes is presented and the main effects and interactions of three main factors are determined in order to establish the optimum experimental conditions in terms of compressive strength. Finally, a regression equation that predicts accurately the real compressive strength of a specimen under various experimental conditions is derived.

Jan 1, 2005

By D. Zaharaki

The optimisation of geopolymer synthesis was studied bymixing low Ca electric arc ferronickel slag with kaolinite, sodium silicate solution, sodium hydroxide pellets and water. The pulp was heated at low temperatures and left for curing at room temperature. Through statistical analysis it was shown that the factors with the most statistically significant effects on the compressive strength of the produced geopolymers are slag particle size and aging period. XRD and FTIR studies provide useful information regarding the progress of geopolymerisation mechanisms. Finally, studies regarding the durability and structural integrity of the produced geopolymers were also carried out.

Jan 1, 2006

By K. Valta

This paper presents an approach for developing a Sustainable Development Indicators (SDIs) framework tailored to the Greek Industrial Minerals sector, due to its importance for the national economy. To achieve this goal, an overview of the Greek mining and minerals, and especially the Industrial Minerals sector, from a technological and a financial perspective, is presented. In addition, a brief description of the global initiatives to this direction is given. The proposed indicators are based on those presented in 2006 by the Greek Mining Enterprises Association (GMEA) adjusted for the sector of industrial minerals by taking into account economic, environmental and social issues, known as the Triple Bottom Line (TBL) approach.

Jan 1, 2007

By Ronald B. Gabitzsch, Norbert P. Hanke

During 1982, record advances have been achieved in the excavation of vertical shafts with a V-Mole (a vertical shaft boring machine). The V-Mole, supplied by Wirth GmbH in Erkelenz, West Germany, has been used in West German coal mines since the early seventies, mainly for the construction of internal shafts. In 1981, it was brought into the United States for the construction of a series of ventilation shafts with depths varying between 512 m (1680 ft.) and 622 m (2040 ft.) excavated to 7.0 m (23 ft.) diameter. These shafts were needed for the development of coal mines for Jim Walter Resources, Inc. in Brookwood, Alabama. After a description of the mechanized shaft excavation system with the V-Mole, the conditions and parameters, such as ground, shaft dimensions, and linings are discussed. These factors are important considerations for a technically and economically feasible utilization of the V-Mole. In addition, the advantages and disadvantages of using the V-Mole technology in comparison to other shaft construction methods are evaluated.

Jan 1, 1983

By Graham G. W. Mustoe

Energy losses are important factors in a conveyor's performance and design. A significant energy loss due to belt sag within a conveyor system occurs when shearing motion between the bulk material particles occurs as the material moves along the belt. An initial analysis of these phenomena was performed using the discrete element method, which is a general-purpose numerical modeling technique for analyzing the mechanical behavior of particulate materials. The software used in this work was Overland Conveyor Company's, Chute Analyst Professional, a discrete element computer code designed specifically for analyzing bulk materials transportation and handling problems.

Jan 1, 2008

By Paul D. Tomlingson

Editor's note: This is the second of two articles on maintenance. Part one: "Downsizing maintenance to improve performance: Defining the downsizing task," appeared in the September issue of MINING ENGINEERING, pp. 1065-1066. Part one explained that downsizing must he an organizational change in which the mine moves to a more efficient, smaller maintenance organization. But the new, smaller organization must operate more productively. Determine initial reduction targets Reduce the workload - The initial reduction target can be determined by projecting manpower reduction as a result of discontinuing or deferring work. Start these reductions by not replacing personnel who retire or are disabled. Observe the right craft mix during this initial reduction. Improve productivity - Further reductions can come from better productivity. But achieving the higher productivity level will require a year or more. During this transition, the efficiencies of a well-defined program and a team organization must take hold.

Jan 1, 1994

By J. A. Cole

Santa Fe Pacific Gold's Lone Tree mine is located in Humboldt County, NV, 45 km (28 miles) east of Winnemucca. The mine currently operates a 1.74-Mt/a (1.92-million stpy) run-of-mine heap-leach operation and a 2.27-kt/d (2500 stpd) refractory gold¬ore-processing plant. Most of the mill-grade ore reserves are refractory, mainly due to pyrite and arsenopyrite encapsulation of the gold. The autoclave pressure-oxidation circuit was commissioned in February 1994 to process the refractory ore. Mineralogy unique to the Lone Tree deposit allowed for the design of a partial-oxidation process. It takes advantage of the heterogeneous nature of the pyrite morphology. Partial oxidation has resulted in an autoclave plant that is able to achieve low operating-unit costs (Figs. 1 and 2).

Jan 1, 1995

By M. Kyzeridi

The paper presents a study on the reclamation of two mined-out bauxite open pits in the area of Kefali, Itea, Greece. The mining area has been reclaimed partially in the past, but its proximity to the town of Itea and a national road with tourist traffic, rose the interest to examine various scenarios for improving the landscape and the aesthetics of the site and introducing alternative land-use for recreational activities. Geospatial data were modelled using a Geographical Information System (GIS) that made it possible to study alternative proposals in terms of final landscape profiles, volumes required to be moved and the associated costs.

Jan 1, 2002

By V. Avdiyskiy

The most pressing topic raised nowadays by the world community faces environment and social consequences of the business intensification process, primarily that of mining and mineral industry, which is through the number of its activities mostly associated with pernicious impacts. World top managers are confronted with the dilemma of reconciling traditional financial framework aiming at successful business development measured by revenues, shareholder value, profit margin and incorporating Sustainable Development (SD) at all levels of decision making process, avoiding depriving future generations of the means to meet their own needs. The rapid consolidation and globalization of the industry stipulates that companies are an integral part of the world economic environment. Therefore a company?s financial performance is under the pressure of operational and environmental performance. Among them special attention is paid to the social and economic background, the relationship with regulatory institutions, and the developments for environmental protection.

Jan 1, 2003

By James P. Dorian

In 1990, the former Soviet Union ranked first worldwide in the production of asbestos, chromium, iron ore, iron and steel, lime, manganese, mercury, nickel, peat, potash, and titanium. Since the middle of this century, that nation had maintained one of the world's most valuable mineral industries, ranking number two in 1950 and number one in 1990. It is clearly an enormous mining industry, with more than 1300 enterprises and an estimated employment base of 1.2 million persons (Table 1). Despite its size and historical achievements, however, the mining industry of the 1990s in the former Soviet republics is encountering problems in performance, efficiency, transportation and utilization. The industry operates below full capacity and is plagued by outdated technology and equipment, rising production costs, capital shortages and labor strikes, in addition to general economic deterioration and civil unrest. Attempts to boost domestic minerals supply in the republics so far have failed because of economic difficulties. And the republics lack the financing required to initiate new, large-scale development projects.

Jan 1, 1992

By Chapman Young, Donald E. McCarthy

Many hard rock tunneling projects, where the majority of excavation can be accomplished with TBMs, will still require considerable specialized excavation which can not be done with a TBM. This secondary excavation, involving cross cuts, galleries, flattening of the invert, increases in bore diameter, et cetera, may be accomplished with conventional drill and blast, applied on a small scale and usually with fracture control techniques, or with mechanical splitters. The problems of using explosives in many of these cases and the high cost of mechanical splitting excavation make the consideration of other approaches attractive. The PCF rock excavation method, which has recently been reduced to commercial practice for mine-development excavation, offers an attractive alternative to drill and blast and mechanical splitters. With the PCF method the rock is excavated utilizing a small-charge, propellant-driven, controlled, penetrating-cone fracture process. Excavation is carried out continuously by combining the PCF hardware with integrated mucking capabilities on a carrier which remains at the excavation point. In addition to the benefit of providing for complicated excavation geometry, the PCF method also causes minimal damage to the remaining rock which will significantly reduce ground support requirements. In very bad ground, the continuous nature of PCF excavation allows ground support to be applied as limited sections are exposed thus reducing both the duration and extent that the ground would be free to move. Data on PCF excavation parameters, as measured in actual mining operations, indicate that crosscuts, galleries and the like could be excavated at considerable cost savings compared to drill and blast or mechanical splitters.

Jan 1, 1995

By R. D. Miller, L. Schulte, J. Davenport, D. W. Steeples

Shallow seismic reflection methods were successfully used to delineate the subsurface extent of roof failure associated with the dissolution mining of a 120-m (400 ft) deep and 60-m (200ft) thick salt bed in central Kansas. Surface subsidence at North American Salt's Hutchinson, KS, salt-dissolution well field represents a potential risk to surface structures and transportation facilities. Three intersecting common depth point (CDP) seismic reflection profiles, targeting the subsurface around an actively subsiding sinkhole, possess sufficient resolution to delineate the horizontal and vertical extent of subsurface rock failure associated with the subsidence. The three seismic profiles showed a disturbed subsurface area 90 to 105 m-diam (300 to 350 ft-diam) at a depth of between 60 to 75 m (200 ft and 250 ft). Confirmation drilling verified the interpretation of the seismic data. The seismic reflection method has the potential to resolve disturbed subsurface areas greater than 23 m-diam (75 ft-diam) at this site.

Jan 1, 1994