Search Documents

By John A. DesLauriers

INTRODUCTION This paper will update the status of small sized tunnel boring machines used in both the Mining and Civil Industries. I will mention a) new developments in small size hard ground tunnel boring machines, b) review North American performance records of the Atlas Copco Mini/Midi Fullfacers, and c) compare relative costs in driving a 1200m (4000 ft) typical utility tunnel using a leased TBM versus the conventional drill and blast method. NEW DEVELOPMENTS JARVA MACHINES Of all small rock tunnel boring machines currently in use, the Jarva MARK VI and MARK VIII are receiving the most enthusiastic acceptance. These circular fullface borers using usually 15 inch single disc cutters (manufactured also by Jarva) are designed on the 'T' bracing principle. Previously, Jarva's line of tunnel boring machines, even their smallest, was designed on the 'X' or double diagonal bracing configuration with a gripper in each quadrant. In small tunnels where net room is so very important, the 'T' scheme with gripping only at the spring line nets precious room around the cutter unit for passage of men and supplies. It allows freer un-

Jan 1, 1981

A series of flotation experiments were carried out in a 2.25-dm3 laboratory-scale Rushton turbine cell using hydrophobic quartz particles. Flotation was performed at a constant mean bubble diameter over a range of superficial gas velocities and impeller rotational speeds. The overall flotation rate constant increased linearly with increasing superficial gas velocity (and hence bubble surface area flux). The rate constant also increased linearly with increasing energy dissipation, until a maximum value was reached. A further increase in energy dissipation had little effect on the rate constant. The dependency of the rate constant on energy dissipation is a reflection of the size range and hydrophobicity of the particles used in this study. The flotation rate constant increased with increasing particle size, except at the highest energy dissipation value examined, for which the flotation rate of the larger particles reached a plateau and, in some cases, decreased. Good agreement was obtained between the experimental results and those predicted by a fundamental flotation model using experimentally measured values for mean energy dissipation and the Sauter mean bubble diameter. The bubble velocity was adjusted to obtain the best fit to the experimental data. The inferred bubble velocity, based on the flotation model, was found to increase with increasing superficial gas velocity (and bubble surface area flux) and was found to decrease with increasing impeller rotational speed. While the inferred bubble velocities were significantly lower than experimentally measured bubble velocities, and, except at low superficial gas velocity values, significantly higher than the bubble swarm velocity calculated from gas holdup measurements, similar trends with impeller rotational speed and superficial gas velocity were observed in all cases.

Jan 1, 2007

By Brian Fulcher

The Arrowhead Tunnels Project represents the final portion of a 70 km (44-mile) long water conveyance facility that will bring up to 28 m3/sec (1,000 ft 3/sec) of water into Southern California. The 13 km (8-mile) tunnelling project is well underway and consists of two, 5.8 m (19-ft) diameter TBM bores through extremely variable geological conditions. An extensive and essential pre-excavation drilling and grouting program was performed in all reaches of the Arrowhead Tunnels Project, located north of San Bernardino, CA. This program supported the advance of two hybrid hard rock TBMs though extremely challenging ground conditions under substantial ground cover and up to 27 bar (900 ft) of ground water pressure. The well known San Andreas Fault lies nearby and has greatly influenced the local geological conditions. This paper will describe the means, methods and materials used throughout the numerous phases of the pre-excavation grouting program. It will also describe many versatile, flexible and innovative drilling and grouting methods and equipment systems utilized to improve performance, save time and costs in constantly changing geological conditions. Considerable lessons learned have been learned while overcoming some extremely formidable ground conditions and safely advancing the tunnels.

Jan 1, 2008

By Mark N. Savit

It is indeed a rarity for a non-engineer, let alone a lawyer, to even be considered for a mining-related award, especially where that award is for significant contributions to technical progress in the mining and exploration sectors. So, when I was notified that I had received this award, I struggled for a topic that would meld the legal world that I operate in with the engineering driven world of exploration and extraction. The most exciting part of my job has always been the opportunity to absorb the technical details of the cases I work on and, in effect, translate them for a lay audience. Too often, I have found, lawyers, judges, legislators and yes, even regulators who lack a technical background simply give up trying to understand the details of the very conditions or processes that they are trying to describe and simply repeat phrases told to them by their client or by a retained expert.

Jan 1, 2008

By A. P. Grobbelaar

Andalusite is a member of the sillimanite group of minerals consisting of andalusite, kyanite, and sillimanite. These minerals are the structural polymorphs of Al,Si05 (the anhydrous silicate of aluminium) and although chemically similar, they differ in physical properties due to their different crystal structures. For further information on the sillimanite group, see the chapter on Kyanite and Related Minerals that follows. The minerals are generally the products of the metamorphism of alumina-rich sediments and are found in schists, gneisses, or hornfelses, which have undergone either regional or thermal metamorphism from their original form. Sedimentary deposits may also form since the minerals are chemically and physically resistant to breakdown. When heated to a sufficiently high temperature the sillimanite group minerals convert to mullite with a resultant volume expansion and the liberation of silica. Due to the stability of the mullite formed, its high hot strength and resistance to chemical and physical erosion, they are widely used in the manufacture of refractories and special ceramics (Table 1). The reaction can be represented as follows: [ ] The worldwide use of these minerals depends to a large degree on their availability (Fig. 1). Andalusite, with its lower conversion temperature and the lowest volume expansion on being heated is the natural choice as a raw material to produce energy-saving refractories without prior calcination. The Republic of South Africa holds by far the largest minable andalusite deposits of the world, estimated at some 70 Mt of known in situ reserves. The only other large commercial production of andalusite comes from France, with known reserves of about 5 Mt. Potential new deposits are known from China, Ireland, Australia, and South America. World consumption of andalusite in special performance refractories has risen from less than 10 ktpy in 1960 to nearly 300 ktpy in 1990, which is due to cost effectiveness in many industrial applications compared to other conventional refractory products. Andalusite-based refractories have traditionally been used in Europe, South Africa, and the Far East; usage in America was limited in the past due to relatively high delivery costs and availability of other local refractory minerals. However, there is a significant trend towards greater use of andalusite in North America, thus opening new markets and replacing other traditional refractory raw materials. GEOLOGY Andalusite occurs in metamorphosed rocks of clay-like com- position, as in the andalusite-hornfelses in thermal aureoles (contact metamorphism), formed under conditions of high temperatures and low stress, and in regional metamorphic rocks, such as the andalusite-schists. These schists are mostly unconnected with definite igneous intrusions but were presumably also formed at high temperatures and under low stress. Andalusite can also appear in alluvial deposits associated with the primary deposits. At depths of 10 to 20 km, temperatures of up to 450°C might be expected. Another result of increasing depth is an increase of pressure due to the load of the rock cover. The load stresses involved in metamorphism is generally believed to lie in the range 0 to 10 000 bars. During contact metamorphism the increase in temperature is brought about by the injection of magma. The temperature reached in the country rock at some distance from the igneous body will always be less than the initial temperature of the intrusion, which is presumably less than 1 200°C, and will vary with time and distance from the contact. A simple metamorphic reaction involving dehydration of an aluminous sediment can be: [ ] At higher temperatures sillimanite would form at the expense of andalusite, while kyanite would be the mineral formed at higher pressures, as can be seen in the phase diagram of A12Si05 (Fig. 2).

Jan 1, 1994

By R. L. Guerguerian

Nowadays, most grinding mills driven by a wrap-around ring motor are operating successfully. Some of the earlier problems could be attributed to the lateral stiffness and stability of their bearings. As a result, modifications to the bearings included the rearrangement of the shoes, or the addition of more shoes, closer to the horizontal centerline. This technical paper reports a study of the effects of bearings on the lateral stiffness of grinding mills driven by a wrap-around ring motor. The discussions cover the design of the four shoe trunnion bearings and examine the effects of the angular location of the shoes.

Jan 1, 2000

By Yanan Zhang, Hongwei Deng, Feng Gao, Bo Ke

Recently, liquid carbon dioxide (L-CO2) blasting technology has attracted attention due to its good fracturing effect and safety performance, especially in coal seam permeability improvement. This paper analyzes the blasting effect of L-CO2 based on experiments and studies the fracturing mechanism from the perspective of stress wave action via theoretical analysis and peridynamic simulations. The results indicate that L-CO2 blasting achieves a good fracturing effect without forming a crush zone, and the loading rate and strength of the stress wave are key factors.

Jan 19, 2022

By Earl G. Hoover

For most geologists and miners the term "asbestos" refers to a group of highly fibrous silicate minerals that readily separate into long, thin, strong fibers of sufficient flexibility to be woven, are heat resistant and chemically inert, and possess a high electric insulation and therefore are suitable for? uses where incombustible, nonconductive or chemically resistant material is required. The United States Mining Enforcement and Safety Administration (MESA) specifically refers to the naturally occurring minerals chrysotile. amosite, crocidolite, termolite asbestos, anthophyllite asbestos, and actinolite asbestos as "asbestos" if the individual crystal fragments have the following dimensions; length -greater than 5 micrometers, maximum diameter -less than 5 micrometers, and a length to diameter ratio of 3 or greater. Since asbestos has been identified as one of the ten most carcinogenic substances (a cancer causing agent) it has become, for many government regulatory agencies, a major issue concerning banning emissions to the environment.

Jan 1, 1978

By R. Kaushik

According to the U.S Department of Energy (DOE), mineral processing activities including comminution (size reduction) uses 4% of the world electrical energy consumption. Such numbers reinforce the need to invest in energy savings initiatives in order to produce more using less. ENERGY EFFICIENCY OPPORTUNITIES AND CHALLENGES IN MINING OPERATIONS In addition, DOE, in its Mining Industry Energy Bandwidth Study, has identified huge potential for energy savings for the coal, metals and mineral industries. Even knowing the overall causes of energy waste and some potential tools for remediation, mining companies may struggle to apply such tools and get the desired results due to the following reasons: ? Limited staff ? Lack of accurate economic and investment analysis to justify energy savings projects ? Lack of knowledge to identify low or no-cost savings opportunities ? Internal competition for resources According to the workforce and talent management experts, the Talent Strategy Advisors, the demand for mining engineers is expected to exceed supply by 30% by 2013. Mining personnel are likely to be burdened with increasing and varied workloads with limited training. This will result in the need for automated and simple tools to support energy efficiency activities. Mining engineers will simply not have the time and resources to create such tools, collect and analyze the data to make decisions, and track results.

Feb 27, 2013

By R. S. Shepard

The closing remarks of a paper which I presented at the annual AIME meeting at Dallas, Texas during February of 1963; contained a forecast of increased activity in trackless underground ore mining which finalized that presentation. At that time, HAD I been peering through my brightest rose colored glasses, I could not have foreseen the unprecedented rapidity of acceleration of underground ore mining methods which has since ensued. From Death Valley, California diagonally to St. Johns, New Foundland; from Australia to Africa to Sweden to France and Germany; from South America to Southern Mexico to Northern Saskatchewan and Northern Manitoba the expansion of trackless underground ore mining methods has probably progressed at a faster rate than any other revolutionary' change in the history of underground ore mining.

Jan 1, 1967

By William R. Yernberg

The 2003 Rapid Excavation and Tunneling Conference (RETC) was held at the New Orleans Marriott, New Orleans, LA, June 15-18. The New Orleans conference was the 16th since the RETC was formed in 1971. This year’s conference was sponsored by the Society for Mining, Metallurgy, and Exploration, Inc.(SME), with co-sponsorship of the Construction Institute of ASCE. Attendance at the meeting was 1,178, a conference record. This was up significantly from the771 attendees at the 2001 meeting in San Diego, CA. The RETC was formed to “advance the engineering and scientific knowledge of rapid underground excavation and tunneling through interdisciplinary meetings, publications, technical-educational exhibitions and encouragement of research.” The RETC conferences are now held every other year. They provide an opportunity for individuals to meet with designers, contractors and manufacturers associated with the tunneling industry to share experiences in all phases of tunnel design and construction.

Jan 1, 2003

By James C. Bradbury

Tripoli is a naturally occurring, finely divided form of silica found chiefly in midwestern and southeastern states and used commercially in fillers and abrasives. The name comes from the location of a silica deposit in North Africa and was applied in the latter part of the 19th century to similar material near Seneca, Missouri. Subsequently, the North African material was found to be diatomite, composed of siliceous skeletons of microscopic marine plants called diatoms, and the material's name was changed to tripolite. The name, tripoli, remained with the Missouri silica, which is inorganic in origin, and tripoli is now used to designate all naturally occurring silica that is similar in characteristics and origin to the Missouri material. Just to confuse things further, in commercial trade tripoli usually designates silica from the Missouri-Oklahoma field, whereas silica from southern Illinois, the other major producing area, is called amorphous silica. Each term, however, may be used commercially for any material, regardless of place of origin that has the characteristics or uses ascribed to material from either major producing area. For example, Engineering and Mining Journal routinely lists under "tripoli," prices "f.o.b. Elco, I11." and "f.o.b. Seneca, Mo. and Rogers, Ark.", and under "silica, amorphous," prices "f.o.b. I11 and "f.o.b. Dierks, Ark." "Soft silica" is another term that has been applied to tripoli from Illinois, west central Arkansas, and Tennessee, presumably to distinguish it from the more compact Missouri material. It has also been used in the ceramic trade to distinguish tripoli from "hard" silica, or silica flour, which is produced by pulverizing silica sand. Tripoli is produced mainly in extreme southwestern Illinois, in the Missouri-Oklahoma district in Newton County, Missouri, and Ottawa County, Oklahoma; and in the novaculite belt of west central Arkansas. Some tripoli is produced for local and specialized uses near Austin, Texas.

Jan 1, 1980

Despite the current economic downturn that is now decimating iron ore production, Minnesota?s mining operators remain optimistic about the long-term prospects for the industry. Reflecting this optimism, the development of several new mining projects continues in the state. The future of mining in Minnesota was the featured topic at the combined 82nd Annual Minnesota Section of SME Meeting and 70th Annual University of Minnesota Mining Symposium. More than 500 mining industry professionals, including engineers, executives, mining managers and equipment suppliers from the around the world, attended the meeting, which was held April 14 and 15, 2009, in Duluth, MN. The combined meeting featured a keynote session with three distinguished speakers plus a panel discussion by representatives from several of Minnesota?s taconite producers. The keynote speakers were Curtis Clark, president and chief operating officer, Behr Dolbear, who gave a presentation on the ?State of the Mining Industry.? Phil Newman, chief operating officer, CRU Strategies, spoke about challenges facing the mining industry and James A. Skurla, acting director, Bureau of Business and Economic Research, Labovitz School of Business and Economics, University of Minnesota Duluth, discussed the importance of mining to northeastern Minnesota?s economy. The taconite producers panel discussion included Jonathan Holmes, vice president and operations manager, ArcelorMittal; Ed Latendresse, vice president and general manger, Hibbing Taconite; John Tuomi, vice president operations services, United Taconite and Mike Mliner, vice president and general manager, Northshore Mining. The mangers provided updates on their respective operation The meeting included concurrent technical papers sessions on mining, processing, environmental and nonferrous mining. The sessions included technical papers that provided information on the status of a number of new mining projects in the state. The conference also offered a SME short course titled ?The basics of iron mining.? A tradeshow that featured about 100 companies and organizations offering products and services to Minnesota?s mining industry ran in conjunction to the conference. It was estimated that more than 900 people, including conference registrants and special invited guests of the vendors, attended the tradeshow opening reception. This was the largest trade show in many years. The Minnesota Section of SME also held its annual business meeting during the conference.

Jan 1, 2009

By Hojong Kim, Isehaq Al-Nafai, Kwadwo Osseo-Asare

The standard Gibbs free energy of formation (ΔGo f, 298) of bastnasite, (Ce, La, Nd, Pr)FCO3, was estimated using four different methods. The obtained average values were − 1589.5 kJ/mol for CeFCO3, − 1599.5 kJ/mol for LaFCO3, − 1589.1 kJ/mol for NdFCO3, and − 1595.4 kJ/mol for PrFCO3. The value for cerium bastnasite, CeFCO3, was used to construct a potential vs. pH (Eh-pH) diagram to investigate the stability relations of cerium bastnasite. The diagram shows that CeFCO3 is stable in neutral to basic conditions (pH ~ 6.5–11).

By Grant P. Cordon

Our subject, "Safety, Legal, and Contracting," is a range of topics which covers a broad spectrum, but is obviously Intended to focus our attention upon certain particular aspects of tunnel problems. These are all fascinating and complex subjects, and others are much more qualified to discuss to discuss the fine points involved. Put after some 45 years' involvement as an inspector, engineer, contracting officer, and especially for the last 22 years as a contractor's estimator and manager, I have developed some strong and definite convictions to share with you. I hope it will serve to get you started thinking. My first tunnel experience was in a soft ground tunnel which was dug by hand, literally. The crown or arch back was taken out, a pebble at a time, by bare hand. The face was constantly breast-boarded, and the mucking was all done by hand shovel. My first rock tunnel was drilled by hand held drifters from the muck pile. Since then, most tunneling techniques have improved greatly. The jumbos, booms, muckers, and moles have taken over many of the back-breaking chores, and reduced the manpower requirements.

Jan 1, 1974

By David G. Hammond

INTRODUCTION Previous papers and discussions at this conference have already covered the subjects of identification and nature of risks, allocation of risks and contractual arrangements. In this portion of the conference, in the light of topics already covered, we will consider how to minimize risks and how to mitigate losses. Webster defines mitigate as "to make less severe or painful", an apt definition for our purpose! RISK MANAGEMENT POLICY The first thing that must be said about risks, especially in construction, is that they exist and that they don't necessarily fall alike on the just and the unjust. Some risks, i.e., some kinds of risks, must be recognized as inevitable in engineering and construction and therefore must philosophically and realistically be accepted as part of situations to be dealt with. Dealing with means minimizing, covering, and sharing of risks and doesn't mean merely passing off the risks to someone else. While some risks can be avoided, for example, whether the structure will fall down or the excavation will cave in, risks management primarily deals with: A. minimizing risks---whomever risk it may be B. equitable sharing of those risks among the participants.

Jan 1, 1979

By G. S. S. Raman, M. S. Klima

The effects of pressure and cake thickness were studied using a split-plot design for pressure filtration of a fine refuse slurry obtained from a bituminous coal preparation facility. Pressure filtration offers the potential to significantly reduce the moisture content of the fine refuse stream with the addition of little to no flocculants, thereby minimizing the volume of refuse stored in impoundments and providing a recycle water stream for use within the plant. Experimental results showed that the final cake moisture decreased with increase in pressure and decrease in cake thickness. In addition, specific cake resistances calculated for the various tests indicated an increasing trend with increasing pressure and decreasing cake thickness. With increase in cake thickness, an increase in cake moisture and the weight of solids deposited in the cake was observed. An ANOVA analysis indicated that both cake thickness and pressure significantly affected the cake moisture, while only cake thickness statistically influenced the weight of solids in the cake. A regression model was developed with an R2 value of about 0.99 to relate cake thickness, the single largest statistically significant factor, with the weight of solids in the cake. Filter capacities were calculated in terms of the solids deposited per unit time based on a product specification of 25 percent cake moisture, and it was observed that the thinnest cake had the highest filter capacity.

By H. Maleki

As mining continues toward deeper reserves in thick western US coal fields, the control of mining induced-seismicity has become a priority in many operations in Utah, Colorado, and Wyoming. Gradual floor heave, common in many coal mines, has historically not been a safety issue. However recent occurrences of sudden floor heave accompanied with seismicity in a few deep mines have fueled this investigation. The focus is to identify and study the mechanisms resulting in sudden heaving of the mine floor in western U.S. deep coal mines through analytical calculations and back analyses of an actual event in a cooperative mine. Based on review of available data in three mines, underground observations and back analyses of an actual event, the authors have identified the following contributing factors (1) presence of stiff stratigraphic units and thick seams mined at depths exceeding 1000-ft (2) presence of geological discontinuities reducing the in-situ strength of the coal with calculated factor of safety near 1 for the mine floor (3) mining approaching areas of higher than normal stress gradient associated with previous mining or structural anomalies or surface topographic highs and (4) an additional source of energy triggering sudden failure such as periodic caving or slip along geological discontinuities. Preliminary examination of seismic data for the actual event in the cooperative mine and underground observations excluded fault slip at the mining horizon as the triggering mechanism but highlighted the significance of weak, anisotropic strata conditions near the intersection of two faults.

Jan 1, 2009

By Y. A. Attia, M. Elzeky

Thiobacillus ferrooxidans bacteria were used in this work to study the effect of bacterial adaptation on the bioleaching of three iron-bearing sulfide minerals, namely, pyrite, chalcopyrite and arsenopyrite. The change in the pH during the bioleaching process was observed and the mechanism of the bacterial action were discussed. It was found that bacterial adaptation prior to bioleaching, enhanced the degree of sulfide leaching by 2-4 folds over that of non-adapted bacteria. A1 so the bacterial activity was enhanced by 2-4.8 folds. The pH of leaching solutions was decreased by the increase in both adaptation period and bioleaching time. It was also concluded that the mechanisms of bioleaching of iron-bearing sulfide minerals involved both the direct and indirect bacterial action simultaneously.

Jan 1, 1989

This paper presents a virtual prototype for the stress analysis of cable shovel components based on combination of flexible and rigid body approach. The general mechanical system of the cable shovel is modeled as a multi-body system with rigid and flexible bodies. The relevant theories applied for the dynamic model are described in terms of Lagrangian multi-body dynamics and finite element method. A virtual prototype of the cable shovel is built in the Automatic Dynamic Analysis Mechanical System (ADAMS) environment, which allows visualizing the motion of general mechanical system and analyzing the dynamic stress of structural components of the cable shovel. An example is given to perform dynamic stress of durability analysis for the boom and handle. Attention of this study is devoted to the mechanisms of damage of the cable shovel and also the critical high stress areas. Keywords: Cable shovel, Von Mises stress, Virtual prototype simulation, Stress virtualization.

Jan 1, 2009