Search Documents

By Karl H. Gehring

According to the increasing importance of boom type roadheaders in tunnelling essential problems occuring in the application of these machines are dealt with. Based on a chart including the various stages for decicion finding the excavation method of underground cavities, both the technical limits and economic criteria are discussed in order to determine the range of applicability of roadheaders. Giving examples-the numerous developments in the fields of pick and cutting technology, performance data of boom type roadheaders in hard rock, safety technology and increase in the machines' degree of utilization, research and development of VA is illustrated. Two topic operation examples show partial aspects of the various tendencies of development.

Jan 1, 1981

By R. B. Coleman, T. P. McNulty

HISTORICAL PERSPECTIVE Environmental protection is not a newcomer to the minerals industry, there having been numerous examples dating from decades ago. Sometimes the awareness of a need for preservation or restoration derived from the ethics and principles of the engineers and management responsible for development and operation of a property. On the other hand, pressures to clean up industrial messes frequently were applied by special interests such as farming and ranching, recreational and conservational groups, and local governing bodies. Mineral industry environmental controls in this century have therefore been a patchwork of good intentions and bad, clean operations and dirty ones. The Hoboken siphon converter for converting copper matte while effectively capturing sulfur dioxide at a relatively high concentration was developed in Olen, Belgium in 1928, a full sixty years ago. The alternative was closure of the Hoboken smelter by Belgian government health officials who had become intolerant of sulfur dioxide emissions which were causing serious respiratory ailments in the river valley in which Olen is situated. As early as 1958, the Anaconda Company had a full-time botanist on its metallurgical research staff with the responsibility of learning how to vegetate the extensive tailings deposits at Anaconda, Montana. By that time, considerable progress had already been made in restoration of Silver Bow Creek, which at one time was “dead” for as far as 40 miles down- stream from the point of entry of acid mine drainage in Butte.

Jan 1, 1989

By G. L. Merritt

The implementation of the Surface Mining Control and Reclamation Act of 1977 (SMCRA) has evolved into one of the most complex environmental protection programs to come out of the late 1970's. The level of detail in the statute and the regulations have resulted in a rigid and complex set of requirements for the administration, permit-ting, inspection and enforcement of the program. In addition, the constant change of the federal program caused by regulatory changes, reorganization of the Office of Sur-face Mining Reclamation and Enforcement (OSMRE), ongoing litigation involving OSMRE, and the use of the budget to establish additional mandates on OSMRE and the State Regulatory Authorities have resulted in an unstable program. The instability of the program makes it extremely difficult for the States to implement their programs and to achieve the goals of SMCRA.

Jan 1, 1988

By Louis A. Sandbak

Drift excavation by boom-type roadheaders in the San Manuel and Kalamazoo sulfide copper ore bodies has been successfully demonstrated. Geomechanical rock classification in conjunction with detailed geologic mapping has been necessary to assess roadheader performance, and to predict advance rates in the varied rock classes in the San Manuel block caving mine. Rapid excavation and less fractured ground are obvious advantages of roadheader drift excavation over conventional drill and blast techniques. The geomechanical system of Engineers International (1984) can be an effective roadheader performance and ground support tool.

Jan 1, 1985

By R. K. Mehta, C. W. Schultz, R. R. Mallepali

Stirred ball mill feeds used for ultrafine grinding applications require a fine size separation step to avoid overgrinding. This paper presents the selectivity curves obtained for oil shale and complex sulfide ore using a 460-mesh (30-µm) Derrick vibrating screen. The selectivity curves generated from the experimental data show increasing selectivity with larger size for the oil shale but not for the sulfide ore. These unusual selectivity curves are similar to the mechanical air separator, fishhook selectivity curves described by Luckie and Austin. A two-stage, in series, classification model describing the fishhook selectivity curve has been used in proposing the classification mechanism for fine vibrating screens when a heterogeneous, multicomponent sulfide ore undergoes size separation.

Jan 1, 1994

By Michael Karmis, Emily A. Sarver, Ellen S. Gilliland, Leigh-Anne H. Krometis

"Public engagement is increasingly important in ensuring the success of projects related to energy development, particularly with regard to issues of environmental protection, public health, and socio-economic impacts. This is due to concurrent trends in public behavior, including a rise in public interest in these projects that is not matched by a rise in science literacy, and increasing organization and participation of the public through social media, citizen science, and grassroots initiatives. In recent years, several high-profile incidents have demonstrated that when public concern is ignored or met with a passive response from industry, it can rapidly grow into organized opposition that negatively impacts or wholly derails a project. Engaging, listening to, and educating stakeholders during early planning and development phases are therefore essential to earning credibility and trust. Moreover, maintaining two-way lines of communication throughout the lifespan of a project demonstrates social responsibility and facilitates cooperation, acceptance, and even support from communities and others. Positive experiences with specific projects at a local, community level can influence the larger public opinion of an entire industry sector. This paper presents cases studies of public engagement related to shale gas development (including hydraulic fracturing and pipeline construction), mountaintop removal mining, and management of mixed-use watersheds near surface mining operations. The experiences highlighted in these case studies are used to draw best practices of public engagement for sustainable energy development.Introduction Within the scientific research community, the importance of public engagement has gained increasing recognition. In a 2007 article in Nature, medical researcher, Patrick Taylor, stated that public engagement has both “gone viral” and “gone global” and has the ability to make real impacts to research (Taylor 2007). Nancy Baron, the science outreach director for COMPASS, an organization providing communications training for scientists, provides further evidence for the increasing focus on engagement, including shifting attitudes observed during her own experience as a communications coach and documented in surveys, the recent inclusion of communication and engagement activities in academic tenure review, and the surge of workshops, materials, and other resources available on the subject (Baron 2016). In addition to COMPASS, a number of organizations and institutes have been developed to train scientists for communication and engagement with the public, perhaps most notably the Alan Alda Center for Communicating Science at Stony Brook University, and academic fellowship programs, such as the Leopold Leadership Program at Stanford University and the Wilburforce Fellowship Program, have been established for the same purpose."

Jan 1, 2017

By Allan T. Fisk, Carl R. Peterson, Robert G. Lundquist

A long recognized goal in high speed tunneling and mining has been the development of a continuous drill and blast excavation capability. Both the advance rate and the economy of drill and blast tunneling can be significantly improved if the conventional cyclic process can be carried out continuously. Obviously, any continuous drill and blast tunneling machine must be an "all function" device, performing drilling, explosive loading, initiation, mucking, ventilation, roof support (if necessary), and perhaps other functions, essentially simultaneously, while remaining at the face throughout. Furthermore, such a machine must do all these things under remote control. THE SPIRAL BLAST PATTERN Several continuous drill and blast tunneling concepts have been proposed. Of these the Rapidex spiral blast pattern, taking advantage of a partially self-shielding geometry, seems to require the least shielding and hence offers the maximum access for mucking, although from the outset it was clear that remote mucking would present a major design challenge. The Rapidex continuous spiral blast concept uses an unusual blasting pattern that, under the geological conditions tested, has proven to be an effective and efficient means of fragmentation. The concept has a self-shielding characteristic which permits a lightly shielded machine to remain at the face during blasting. The pattern produces a spirally proceeding tunnel face, much like one turn of an auger. The leading portion of the spiral surface is connected to the trailing portion by an axially extending plane surface or bench. The ideal geometry is illustrated in Figure 1 for a horseshoe tunnel section.

Jan 1, 1979

By Krishniah N. Murthy, James E. Monsees

BACKGROUND The development of public transportation in the Los Angeles Metropolitan area is, as in other cities, closely tied to the development of the area because of increases in population and commercial and industrial activity. Local transportation first appeared in the area in the 1870s when the population was fewer than 10,000 residents. Around 1910, after many consolidations of competitive interests, two large railway companies were formed: The Los Angeles Railway, which provided urban transportation in the Los Angeles City area, and the Pacific Electric Railway, which primarily provided suburban and interurban transportation. These two entities continued with their operations until after World War II, when the ownership passed on to the Los Angeles Transit Lines and the Metropolitan Coach Lines, respectively. By then the railroads needed new equipment, track rehabilitation, and, of course, more money-paying patrons. Lack of grade separation of railway facilities from other traffic increased commute times and encouraged travel by private automobiles. The romantic era of hopping on a Pacific Electric Company "Big Red Car" was coming to an end. As early as 1917, in fact, bus lines were substituted for unprofitable rail service. The Los Angeles Metropolitan Transit Authority (LMTA) was established in 1951 by the California Legislature to study and plan for improvements in the public transportation facilities in the Los Angeles area. In March of 1958 the Los Angeles Metropolitan Transit Authority took over the operation of the two lines.

Jan 1, 1989

By Herbert H. Einstein, Edward C. Tse, David B. Ashley

INTRODUCTION Decision-making in the design and construction of underground facilities must be made under conditions of varying geologic uncertainty, uncertainty which can have a major cost impact if not properly regarded. Of the two approaches for dealing with this variability, preparing for the "worst" anticipated conditions and optimizing design and construction in-situ, preparing for the "worst" conditions is the more if not solely conventionally practiced method in the United States. While the conventional approach is recognized at times to be extremely overconservative, it will remain preferred until a more adaptable method is shown to be economically superior. This paper presents research aimed at providing just such answers as to when and if an adaptable tunnel design and construction approach is more cost effective than a non-adaptable one. To fully understand the characteristics of this choice between adaptable and conventional tunneling alternatives a summary discussion of adaptable methods is presented. An acknowledgement of the importance of geologic and other factor uncertainties in making this decision leads to the adoption of decision analysis as a quantitative methodology for formalizing the problem. Exercising this methodology on three prototypical tunneling scenarios--urban deep, urban shallow, and transmountain--allows an isolation and ranking of the most crucial factors in making the basic approach decision. One scenario, a transmountain highway tunnel, is carried further through a detailed probabilistic analysis to show under what conditions of varying uncertainty adaptable approaches possess economic advantages.

Jan 1, 1979

By Odd E. Hanssen

In April 1982, the contracting Companies, ABV of Sweden and Hoyer-Ellefsen of Norway forming the Consorcio Escandinavo Agoyan, signed the contract for the construction of the civil works of the Agoyan Hydroelectric Project, located in Ecuador, South America. The project is located in the Andes mountain region of Ecuador - one of the smaller countries in this part of the world, located on the Pacific Coast. The contract was signed with the Instituto Ecuatoriano de Electrificación (INECEL), a public institution in charge of the development of all major energy producing projects in Ecuador, for a value of approximately US$ 120,000,000. The contract's main elements are - Concrete gravity dam with a total volume of approximately 210,000 cu m. (60 m wide x 45 m maximum height, 320 m crest). - 2,400 m of headrace tunnel, interior diameter of finished lining 6 m of which 450 m is in-situ tunnel formed in a trench. - Pressure shafts, 132 m long, the lowest meters with sheet lining, the rest with concrete lining. - Powerhouse cavern with an excavated volume of approximately 25,000 c m in which two turbines of 78 MW each will be installed. - Two 140 m tailrace tunnels with a finished diameter (concrete

Jan 1, 1985

By Pierre Mousset-Jones, Felipe Calizaya

This paper summarizes the current research trends in the ventilation design for the construction of very long tunnels, and presents the results of leakage flow measurements in three auxiliary ventilation systems. The study includes an estimation of an important design parameter, namely, the leakage path resistance, and a discussion of its effects on the overall efficiency of a ventilation system. A sample problem is used to illustrate the calculations.

Jan 1, 1997

By A. C. Lyons

The presentation describes the history, preliminary report, site investigation, including examination of old records, design of tunnel including choice of levels, alternative linings and working sites, the preliminary contract involving shaft sinking on the site of the Tower Block; design modifications, the main contract, including shaft sinking, ground treatment, compressed air installation, machine tunnelling, tunnelling enlargements for chambers, waterproofing and equipment.

Jan 1, 1981

By M. Mohammed, S. J. Jung

The prime criteria in the design of underground openings with complicated geological structures is ground control. Stability of underground openings for deep mines is critical because incorrect orientation or geometry of the shaft, stopes and accessways often results in the failure of openings due to high stress conditions. Current design procedures for complicated orientation and geometry of mines are rapidly becoming inadequate. In this study, the finite element method (ANSYS) has been used with optimization criteria to design safer, more stable underground openings.

Jan 1, 1995

By Carmel Bofinger, Maureen E. Hassall, David Cliff, Eric Stemn

e Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

By Terry A. Ring

Sand bed filters are used to remove large and small particles from liquid streams. The large particles are removed by the straining action of the filter bed and the small particles are removed by particle deposition on the surface of the bed particles. Particle deposition, while being essential for the filtering action of colloidal particles, is not the only process that occurs in the filter bed. Other processes that occur are (1) the substrate becomes filled with particles limiting further deposition, and (2) some deposited particles are resuspended. The sum total of all these processes determine the performance of a filter bed.

Jan 1, 1982

By Z. Stanojevic-Simsic

The aim of this paper was to study sludge dewatering. The sludge which was examined in laboratory scale was produced by neutralization of a mixture of metallurgical wastewaters. Experiments were carried out using synthetic wastewaters with chemical composition similar to that of metallurgical wastewaters, resulting from electrolyte regeneration, copper refining and precious metals recovery. During investigations gravitational and vacuum techniques were examined. Parameters such as water volume, height of sludge and time of dewatering were monitored. In this paper the results obtained are presented and discussed. The application of vacuum filtration enables better dewatering and compaction of sludge.

Jan 1, 2006

By Raphael Mourad, Colin R. Phillips

Fluorescence, radioluminescence, phosphorescence and thermoluminescence in TLD 100 and 700 are discussed and compared. The energy budget in thermoluminescent material is presented in general terms. Results of measurements of radioluminescence, phosphorescence and thermoluminescence in LiF:Mg irradiated with [a] radiation, using simple facilities, are presented. The calculated energy budget in the exposed chips using [a] radiation is compared to published data using [y] irradiation.

Jan 1, 1981

By F. Chavan

1. Introduction The new Cleuson-Dixence development project in the Valais region of the Swiss Alps, involves the construction of a new link between the Grande-Dixence dam (still world recordholder with a height of 300 m) and a power house on the banks of the Rhone consisting of approximately 20 km tunnels and shafts, and involving a fall of about 1900 m. This 1200 MW project will replace an existing 900 MW structure built in the 1960s, no longer considered efficient. The new project comprises a head race drift about 15.8 km long, a surge tank, an inclined cascade shaft 4,2 km long, and an underground power station. The work for lots C and D (head race drift from Tortin to Tracouet, surge tank, six adits ans the complete inclined shaft) was awarded to our group (Prader, Locher, SELL, Losinger, Evéquoz, Dénériaz, Imboden and Bouygues). The geological conditions are: Lower part of the shaft (300 m) : sedimentary - sandstone and soft tertiary sandstone. Middle and upper part (2600 m) : metamorphic - upper and lower carboniferous, interrupted by triasic chipping. The horizontal section (7 km) consists of mica

Jan 1, 1995

By A. Tsouchlaraki

The physical relief is a variable of utmost significance in the course of the analysis, evaluation, design and management of the visual environment. In this sense, there are cases where it would be desirable to isolate the relief from the other elements making up the visual environment and to investigate its visual value separately. Such cases include the technical works that cause major and permanent alterations to the relief, as well as the works, of which the spatial arrangement depends on the morphology of the ground. Slopes, distances, hypsometric difference values, viewsheds are elements of the relief that affect the visual value of a landscape, but also the ability of a particular landscape to accept and absorb new activities. This paper describes an evaluation and prediction model of the visual value of the landforms. A questionnaire survey takes place in order to investigate the public preference, using a sample of 221 persons in the broader area of Athens. The means used to demonstrate the various forms of reliefs are 32 perspective digital relief images. Following this and in order to investigate the elements of the relief that affect its visual value, 20 quantitative indices were developed and examined so as to select the best ones. Linear prediction models of the visual value were investigated from the previous elements, through a regression process. The applications of the proposed model in physical environment planning are many, such as the prediction of visual impact by arranging works that alter the relief of a region, as it happens in mining, metallurgical and waste disposal sites.

Jan 1, 2005

By G. Pierson

Explanations for commodity price levels (or movements) commonly focus on the fundamentals of supply and demand otherwise they are simply assigned to speculative activity. Comparisons of metal-price histories to monetary and other economic data support the argument that the supply of and demand for money are no less important in the determination of price than are the supply and demand of the commodity itself. That these relationships should exist is evident in the price identity and they are consistent with monetary theory. The patterns developed have limited usefulness as predictors, but their recognition is essential for the construction of price scenarios for planning purposes.

Jan 1, 1998