Search Documents

By M. McPherson, P. Mousset-Jones, G. Danko

Calculation of the sensible heat transfer between the rock surface and the flowing air in an underground airway is still fraught with problems. There are only a few results available in the literature for the calculation of the convection in tunnels with naturally rough surfaces. Some of them are purely empirical, while others use a theoretical approach, based on the analogy between heat and momentum transfer, expressing the heat transfer coefficient as a function of the friction factor. A review and evaluation of these results are presented. The heat transfer equations obtained using the different assumptions, vary over a wide range, so that experimental results are needed to determine the formulae and constants applicable to mine airways. In situ measurements of the "physical" and "technical" heat transfer coefficient carried out in deep mines are described. The statistical distribution of the convective heat transfer coefficient on rough surfaces, as well as the regression between the Nusselt and Reynolds numbers in the turbulent flow region, are presented. Radiative heat transfer between the surface and the moist air flowing in a duct of relatively large hydraulic diameter has been taken into account during evaluation. The results will be a definite refinement of those calculations presently used in mine climate simulation models.

Jan 1, 1987

By R. Spring

Artificial intelligence, and especially expert systems, are currently receiving considerable attention. Of interest to the control engineer is the utilization of these tools for real-time process control applications. To evaluate this technology, a real-time expert control system was implemented in one of the grinding circuits at Brenda Mines Ltd. The performance of this micro computer based expert system compared satisfactorily to the proven supervisory control system currently in use. The study confirmed the expectations that expert systems have potential for real-time, supervisory control of mineral processing operations.

Jan 1, 1989

By G. Chi, M. C. Fuerstenau, R. C. Bradt

Reduction of the total energy expenditure in mining and ore preparation processes was achieved by redistribution of the energy from the crushing and grinding steps to the blasting operation. Reducing the burden/spacing distance by 25% or increasing the charge length by 25% during blasting results in significant energy savings in subsequent comminution processes. The energy cost of mining and comminution is reduced by up to 10%.

Jan 1, 1995

By Vanessa M. Torres, Renato S. Costa

This work presents the experience of Cia. Vale do Rio Doce in using Diagnostic Leaching tests to characterize refractory ores and CIP tailings. With the diagnostic leaching results of the highly refractory gold ore from Maria Preta Mine (Brazil), a process flowsheet was defined for a feasibility study of possible process modification on the existing plant. With CIP tailings from its Fazenda Brasileiro and Caué operations the amount of cyanidable gold was determined to aid plant optimization.

Jan 1, 1995

By S. Corrent, F. A. V. Guimarães, M. G. Barbosa

"INTRODUCTION Moisture can be a villain, so new technologies have been explored to make more viable the production of high moisture iron ores. The current work presents the attempt of the utilization of a superabsorbent polymer (SAP) to aid in the screening process and in the ore handling process, such as stockpiles reclaiming and vessels/trains discharge in sub-zero temperature conditions. The results have shown that the polymer can be used in certain cases to improve productivity and increase safety in the process of handling the material (by increasing the TML). However, for size separation no advantages were found upon the use of the polymers. WATER ADSORPTION MECHANISMS The use of water in mineral processing is constant as its utilization brings an increase in the efficiency of separation. Although we have better results in the processing with water, materials with a high content of “natural” moisture can be very difficult to be treated by the conventional methods of separation. Nowadays many studies have been conducted in order to understand the effect of adsorption of water in the particles of complex minerals. Those studies have being divided in many different lines of research such as contact angle of a drop of water and the surface of the mineral to determine hydrophobicity, the particle size distribution and the porosity of particles. Mainly two forms of adsorption of water by the particles are possible: one the water is retained inside porosity of the particles. Laboratory tests developed in China have showed that capillary adsorption is faster in coarser particles that achieve the saturation degree earlier than finer particles (Xuewei Lv et al., 2011). The so called non-porous model considers the effect of water in the bulk sample of iron ores, in a physical connection when all the water works as a binder between particles as shown in the figure 1.If we take into account the compressibility of the system and compaction due to the weight of the bed over the particles, the thickness of the water film between particles is the same but the volume inside different particle size systems is much higher than in a system with particles of same size."

Jan 1, 2018

By Ernest K. Yanful, Paul H. Simms

The lysimeter is a useful tool for evaluating the performance of mine waste covers or liners. A major problem with its application is the possibility for preferential flow into or away from the lysimeter, if the lysimeter soil is finer or coarser than the barrier soil or sub-base soil. Analysis of a field lysimeter using a two-dimensional unsaturated-saturated liquid flow model suggested that preferential flow would occur and little or no water would be collected; however, in the field, the lysimeters collected significant amounts of water. A similar discrepancy was found between the observed and predicted water balance of a simple laboratory test simulating the lysimeter design. Vapour flow and partial flow, two phenomena not generally simulated in conventional flow models, are possible explanations for the difference between field and laboratory observations.

Jan 1, 2000

By T. L. Brekke, T. R. Howard

Stability of an underground opening can be defined in several ways. To geologists and engineers that are used to working in geological environments where the major parts of the works after careful scaling can be left unsupported during the construction period as well as during operation, any rock mass behavior that requires reinforcement, support or lining may be regarded as a stability problem. To colleagues excavating underground openings in geological environments that require continuous use of reinforcement or support and lining "stability problems" are often associated only with those parts of the work where "standard" construction procedure and method of reinforcement or support and lining is inadequate, and special measures therefore needed. In either case, a major objective is to assess the stability problems correctly -as far as possible at the planning stage -- and choose methods for excavation and reinforcement or support that will bring the opening safely and as economical as possible through the problem areas. INTRODUCTION It is not uncommon that stability problems associated with faults or seams have been described as "unexpected." This term has unfortunately been used to indicate that no one knew that the fault or seam existed prior to excavation. A careful review of documented cases where serious stability problems have occurred revealed that the existence of these zones most often was known, but that their behavior was incorrectly assessed prior to or during construction. Miscalculations have been made in terms of the type and magnitude of loads that developed, and in particular in terms of the time-dependant behavior.

Jan 1, 1997

By E. D. Attanasi

Exploration for non-fuel minerals has declined since 1988 as recessionary pressures have slowed growth in the industrialized economies. By most accounts, however, 1990 expenditures were still significantly greater than the low levels experienced in the mid-1980s. The Persian Gulf crisis introduced instability in energy prices and greater uncertainty into an already cloudy economic picture. As 1990 unfolded, the US savings and loan problems spread to the commercial banking system, leading to the failure of several major US commercial banks. The Japanese stock market also suffered significant losses as Japan's Central Bank raised interest rates. The Soviet Union experienced shortages of food and other basic items. Its government faces resistance to changes leading to a market economy. Individual Soviet republics also are seeking more control of their own destiny. The cost of German reunification, in terms of the capital required to bring the east's infrastructure and industrial base to western standards, also appears to have been underestimated.

Jan 1, 1991

By M. J. Hrebar

Surface coal mine design has traditionally relied on graphic and analytic approaches for pit layout and equipment selection. A number of interactive graphic microcomputer programs have been written that aid in the design process in the academic arena and should also have industrial applications. The programs described include a drag-line cut diagram and production index calculation program, a downslope load scraper cut diagram and volume program, and an overburden volume and coal tonnage sequencing program.

Jan 1, 1988

By R. L. Grayson

Conventional mine safety wisdom states that "the most efficient mines are also the safest." Since the 1980s, small mines (and contractors) have been targeted as the most dangerous because of their fatality records. However, statistical analysis of West Virginia safety and production data from 1993 indicated that, when considering the correlation between accident severity and tons mined per employee-hour worked, the most efficient mines were, with the exception of very small mines, not the safest operations. This paper presents the results of an extended analysis of West Virginia mine safety using 1993 and 1996 data and concludes with the method used to suggest current priorities for focusing interventions.

Jan 1, 2000

By R. W. Hagemeyer

By way of background. it is important to keep in mind that the information presented in this paper relates specifically to synthetically produced precipitated calcium carbonate (PCC) fillers. Natural calcium carbonate fillers manufactured by grinding limestone, marble and chalk, though having similar chemical and physical analyses to PCCs, normally contribute somewhat different performance properties in paint, paper and polymer systems. Many factors have been cited and numerous theories have been proposed for the observed differences. Particle size parameters, surface chemistry and particle morphology are the items most frequently mentioned. A discussion of this subject is beyond the scope of this paper.

Jan 1, 1989

By Robin J. Batterham, Dave J. Robinson

The most significant trend in flotation has been the ever-increasing scale of operations. There is, however, doubt that this ongoing trend is enough to maintain the economics against trends such as falling grades, increasing mining costs, pressure on water supply and demand, rising energy demands needed for mineral processing, and a focus on whole of life value and mine legacy issues. We comment on the ramifications of broader uptake of more sustainable mining for mineral processing methods and address the specific question of whether recent progress in in-place recovery will lead to a timely breakthrough. The answer proposed is that this is possible in the next 10 to 20 years, but in the meantime the focus is just as likely to be on removal of waste (beneficiation) much earlier in circuits. Either way, mineral processing and flotation as we know it will change significantly. 

By Ian Longson, Darron W. Dixon

This paper describes the results of an investigation into the application of a statistical method for the prediction of general air-body methane concentration in longwall coal districts. An important and necessary part of the research was the acquisition of representative monitored mine environmental and coal production data. The monitored data was used to build time series models of general air body methane concentration, air velocity, barometric pressure, coal production and methane drainage variables of differing timescales according to the Box-Jenkins method of time series analysis. The univariate models were used to identify causal relationships between methane concentration and its explanatory variables. Coal production was found to be the dominant variable in the determination of the quantity of methane emitted and where appropriate, multivariate time series models were built in which expressions for methane concentration in terms of coal production were obtained. Finally, forecasts of methane concentration values were generated from the multivariate models to determine their forecasting capabilities.

Jan 1, 1993

By Patrick M. Hurley

The spreading-ridge, or accreting plate margin, is the primary conduit of metals delivered to the earth's surface. Isotope ratios of lead show primitive mantle values at these sites, indicating that this is true. We can use lead isotopes in any mineral deposit to indicate the degree to which the metal is "primitive" in the sense of having been uncontaminated with U-enriched crust or "crustal" in the sense that it has been cycling at the earth's surface since earlier times. The reason for this is that the upper continental crust has an enrichment in the ratio of U/Pb over that in the mantle, so that old continental leads have a larger radiogenic component. The primitive metals delivered to the surface at the spreading-ridge are transported on the oceanic plate until they reach a subduction zone. Here they become cycled in the "orogen". However, in this process the primitive metals are mixed with metals from the continent so that the average lead isotope ratios are between those in the mantle and the average upper continental crust. Subsequently a part of the metals in the orogen may become fixed in a new block of continent. However there are processes which continue to uplift and erode ancient continental regions so that there is a continuous feeding back of metals to the orogen. We have therefore a cycling of metals from the existing continental crust into the orogen where they are mixed with new contributions from the spreading ridge and mantle.

Jan 1, 1977

By M. Polat, S. Chander

Many models have been suggested in the past to obtain a satisfactory fit to flotation data. Of these, first-order kinetics models with a distribution of flotation rate constants are most common. A serious limitation of these models is that type of the distribution must be pre-supposed. Methods to overcome this limitation are discussed and a procedure is suggested for estimating the 'actual' distribution of flotation rate constants. It is demonstrated that the classical first-order model fits the data well when applied to coal flotation in narrow size-specific gravity intervals. When applied to material which is fractionated on the basis of size alone, the use of three parameter models, which were modified from their two parameter analogs such as rectangular, sinusoidal, and triangular, gave most reliable results.

Jan 1, 1995

By K. Terhaar, K. Prisbrey

The objective was to determine operating protocols for a lead and silver column flotation cleaner being considered for installation at Sunshine Precious Metals Inc. 's Kellogg mill in Northern Idaho. In this column, tetrahedrite and galena were floated, and pyrite and other gangue minerals, including siderite and silica, were depressed. The procedure was to develop a dynamic simulation using a linear transfer function approach. The transfer function related cause-and-effect variables such as the influence of collector and depressant dosages on recovery and grades. Bench-scale flotation tests followed by pilot column testing provided the data used to develop a linear transfer function. The transfer function was derived using a spreadsheet. This model was applied to simulate how the flotation column could be made to respond to disturbances in feed grade. The results were that xanthate, zinc sulfate and sodium cyanide were found to be suitable controls for grade and recovery. Simulations showed the best sequence of manipulations of these reagents, and these sequences are useful for future operator training. The conclusion was that linear transfer functions were able to simulate lead and silver recovery, develop scenarios for operator training and provide a foundation for future on-line control.

Jan 1, 2002

By C. Waddell

PDMI mines five different grades of ore. Shovel operators were experiencing problems differentiating one material type from another. In 1997 PDMI decided to try GPS ore control to aid operators in identifying material boundaries. Computer generated ore control maps and GPS data defining the shovels' position is fed to a computer on board the shovel. A monitor, located near the shovel operator, displays material types, their boundaries, and the shovels' position and movement in relation to the mining face. This information has reduced errors in material identification by 50%.

Jan 1, 1998

By Simon T. Johnson, Robert J. Fowell

The application of roadheading and drag tool equipped machines requires an assessment of both cutting performance and tool consumption. Neither parameter can be assessed purely from compressive strength and tool consumption is often neglected, at a cost to the project. Results from in-situ monitoring show that a measurement of relative abrasivity using the Cercharscratch abrasivity test provides a basis for the assessment of tool consumption. This can be modified by also considering the effects of the machine specification and the rock mass quality.

Jan 1, 1986

By Krystyna Raszka, Jerzy Iskra

The paper presents results of spectrophotometric investigations concerning the adsorption of sodium oleate on silicon carbide in the presence of the cations of multivalent metals, applying the ATR IR technique with computer-aidedprocessing of the spectrum. The analysis of these spectra indicates the occurance of distinct OH and COOH bands in the pH range in which the hydroxy complexes of metals of the type MeOH+ and MeOH++ reach in the respective cases the highest concentration in the solution. The correlation of these results with those of flotation, measurements of the zeta potential confirms the proposed mechanism of activation of the flotation of silicon carbide, applying sodium oleate as a collector, the collection taking place over the adsorption of hydroxy complexes of the type MeOH+ and MeOH++

Jan 1, 1995

By E. D. Attanasi, J. H. DeYoung

Several factors contributed to continued declines in mineral-exploration activity in the US in 1985. Low metal prices and, what appears to be worldwide chronic excess capacity in copper, molybdenum, lead, and uranium, have resulted in mineral-exploration expenditures remaining anemic. Economic recovery could result in a healthier mining industry and more cash flow to fund exploration. This is because general economic activity and US mining industry activity have historically been closely linked. However, as the worldwide economic recovery has expanded, the mining sector has continued its downward slide. New cuts in industry exploration budgets in 1985 shocked those who thought the exploration situation could not become worse. Some personnel and equipment had been redirected from base metals exploration to precious metals in the past few years. Last year, continued reductions in exploration sent many professionals out of the mining industry. Recent staff reductions or consolidations of operations were made by Noranda, Chevron, Molycorp, and other exploration companies. The latest data from the Society of Economic Geologists (SEG) summary of exploration statistics show that professional staff at year end in major US exploration companies (domestic and foreign operations) fell from 2355 in 1981 to 1868 in 1983 and 1277 in 1984. By the end of 1985, two economic trends were established that could improve the future profitability of mining and hence exploration. First, the price of crude oil began a decline. If sharply reduced energy prices increase worldwide economic expansion, the substantial excess capacity in some of the base metals industries could disappear, and prices could improve. Furthermore, if energy price declines reduce mining and processing costs significantly, metals may recapture some lost markets. The decline in oil revenues has already encouraged some oil-producing countries, such as Venezuela, to look toward development of mineral resources to earn foreign exchange for debt repayment. Second, the decline of the dollar by 21% during 1985 could also help US producers meet foreign competition. During 1985, industry restructuring continued as many oil companies sold off mining subsidiaries and minerals properties. Gold, silver in new discoveries Precious metals continued to dominate the announcement of new discoveries and exploration projects in 1985. A review of domestic exploration and development activities reported in several industry journals shows that 60% to 80% of these projects were directed primarily at precious metals, particularly gold. Base metals exploration activities frequently involved polymetallic deposits with gold or silver values. Because much of this exploration was done on identified targets (on-property exploration), the decrease in wildcat or grassroots (off-property) exploration may be more substantial than indicated by reductions in total exploration activity. Significant gold discoveries in 1985 included several in Nevada, among them the Genesis property of Newmont (near the Carlin mine), Goldfields' discovery of the Chimney deposit in Humboldt Co., and Freeport's discovery of two mineralized sites near Jerritt Canyon. Gold exploration continued to be focused in the western US and Alaska, but gold production starts at the Haile mine in South Carolina, and the Ropes mine in Michigan as well as Amselco's feasibility studies on deposits near Ridgeway, SC, are evidence that gold exploration is not limited to the West. The dominance of gold projects in exploration is not limited to the US, as demonstrated by gold dis¬coveries and exploration projects in Australia, Brazil, Canada, the Caribbean region, China, Guinea, Ivory Coast, South Africa, the South Pacific islands, and Thailand. From the standpoint of US metal miners, it is perplexing that worldwide exploration and development is also taking place in copper, zinc, tungsten, and other metals with depressed prices. During 1985, the US Geological Survey's efforts to map the sea floor of the Exclusive Economic Zone shifted from the Pacific Coast to the deep water areas of the Gulf of Mexico and to areas off the coast of Puerto Rico and the Virgin Islands. An atlas containing sea-floor maps of the west coast area was published as US Geological Survey Miscellaneous Investigations Series Map 1-1792. Results of the 1985 surveys are expected to be published by January 1987. Exploration trends - Statistical evidence Data from the SEG showed continued decline in the US mining industry's exploration expenditures through 1984. The share of US companies' domestic exploration expenditures directed toward base and precious metals has increased from 51% to 84% from 1980 to 1983 and to 86% in 1984. US mining companies spent about $0.67 of each exploration dollar in 1984 in the US. However, this represents an increase from earlier years. The 1983 data also show that firms spending more than $5 million on exploration accounted for 77% of exploration expenditures. Since 1981, the Bureau of Land Management (BLM) has been assembling data on claims and an-

Jan 5, 1986