Search Documents

By A. D. S. Gillies

The provision of a suitable working environment in deep level mines requires the accurate prediction of the ventilation heat load. Mathematical models for predicting strata heat load have been under development since the 1930's and 1940's. Computer models for predicting this and other mine heat sources have been developed and refined over the last 20 years. Some empirical studies have occurred and there is an increased emphasis on the importance of underground studies. Any theoretically or empirically determined predictive method must of necessity make assumptions. Underground space with its irregular configurations and rough wall surfaces cannot be described by simple mathematical expressions. Some heat loads, such as machinery, may occur intermittently while others such as the influence of water evaporation are very difficult to quantify accurately. Current popular models for predicting mine heat load have been surveyed. In testing some of these it is often found that each estimates significantly different quantitative values for the expected load in a particular underground space under study. These differences are explained by the assumptions, simplifications and omissions implicit in each of these models. It would be easier to estimate conditions at any point if heat flow into mine air passageways could be described by simple equations with associated statistically-based confidence ranges. Use of probability distributions to indicate confidence ranges allows any heat level estimate to be expressed as a range of values with limits for maximum and minimum expected values. This approach allows many of the limitations of the popular predictive models to be overcome. A heat prediction method using this approach has been developed based on Monte Carlo simulation and tested on mine data from a number of operations. Heat flow levels which can be predicted by simple equations supported by probability distributions allow the engineer flexibility in adjusting a predictive model to the underground characteristics appropriate to the mine site under study. The influence of all heat sources present in the mine opening must be included. Prediction methods must be updated as mining systems and machinery change with time. Heat sources interact with one another and the system must therefore be understood in its entirety.

Jan 1, 1987

By R. Bhaskar

Although the health effects of airborne dust in underground coal mines are well recognized, a lack of understanding remains about the fundamental mechanisms of dust generation, transportation, deposition and dust-lung reaction. This study was intended to contribute to the understanding of dust transportation and deposition mechanisms in underground mine airways. Data from in-mine experiments carried out under controlled conditions in a straight section of a longwall panel with three different airflow velocities and two different types of coal dust (bituminous and semi-anthracite) were used to determine the turbulent deposition rate of dust particles. Measurements of ambient dust concentrations and deposition along the mine airway were obtained and the total dust deposition velocity (rate) was calculated. The deposition velocity of turbulent diffusion was estimated based on the experimental data and theoretical equations. The effects of airflow velocity, particle size, particle density and distance from the dust source on gravitational, turbulent and total dust deposition are discussed along with related conclusions.

Jan 1, 1995

By Anthony Peach, Lok Home

Introduction Raise boring is the most accepted form of mechanized hard rock boring in the mining industry. It appeared logical to take this mechanization one step further by introducing computers. Atlas Copco Jarva has produced a series of raise boring models that use an integrated computer. The company decided to use electronics and computerization, not for marketing purposes, but to make its equipment more cost-effective. Basis of Cost-Effective Design From the manufacturer's standpoint, it is possible for the equipment owner to reduce the cost of putting in raises by: • Replacing existing components with less expensive components that produce the same results; • Replacing existing components with more expensive components that make the equipment more productive; • Mechanizing equipment to reduce associated labor costs; and • Combining the above. Analysis of a standard raise boring machine (RBM) system showed that little could be done with less expensive components. It appeared, however, that the RBM could be more productive by transmitting more horsepower through the expensive drill string, while being precisely controlled by computers. An RBM system includes a basic machine, drill pipe, accessories, reamer, and cutters. The approximate percentage cost of various components on a standard system capable of boring 300 m (985 ft) long and 3-m-diam (10-ft-diam) aises in medium to hard rock is shown in Table 1. Also shown is the increased cost above standard of the Jarva computerized machine, and the productivity of both. Increased Productivity Penetration is important during the reaming cycle for more productive raise boring. This is possible by increasing the cutter load with constant rpm or increasing the rpm with constant cutter load. To increase thrust and maintain rpm requires increased capacity in the cylinders, drive train, main thrust bearings, drill string, electrical motors, and power units. To increase rpm and maintain cutter load requires only increased capacity in the electrical motors and power units. This is possible because the torque requirement remains constant for a constant thrust load. Only the horsepower increases, proportional to rpm. Since cutter costs are a big factor in raise boring, changes in machine performance must be analyzed to assess the effect on cutter performance. With a standard or typical carbide cutter, as used on raise boring machines, the effects of increased thrust or rpm are shown in Table 2. The assumption is made that the base data is the current rpm and thrust range where the cutters are now operated. It is also assumed one variable is held constant while the other increases. The result of this comparison, approximately, is that a 50% penetration increase can be achieved with little or no increase in cutter cost if rpm is increased 50% and cutter load is maintained constant. A similar 50% penetration increase can be achieved with a 45% increase in cutter cost, if the cutter load is increased by 20% and maintained constant. From an equipment standpoint, it is significantly less expensive to increase rpm 50% than it is to in-

Jan 7, 1984

Water conservation and compliance strategy can be cause for success or failure of a new or existing mining operation. Water accounting at outset, and pit and waste dump planning, may not fully consider total inflows, or sediment loads encountered during mine life. Environmental impact assessments, and permitting often dictates the rules, and these may change, to be more stringent, during course of mine development. This paper will identify techniques to control unprojected fresh water, or increased surface water flows in surface mine operations.

Feb 23, 2014

By R. Kadeg, S. Pavlou

A methodology for developing and utilizing risk-based action levels for soils in site closures is discussed. The methodology is based on standard exposure pathway models which are consistent with current regulatory guidance on conducting risk assessment. A simple approach to evaluating the potential for contamination ground water from the projected criteria based on the Toxicity Characteristic Leachate Procedure (TCLP) is also presented.

Jan 1, 1992

By Craig J. Nelsen, David A. Smith

In 1987, LAC Minerals (USA), Inc. conducted a high resolution helicopter electromagnetic (EM) and magnetic geophysical survey on the Ortiz Mine Grant, New Mexico. The primary purpose of this survey was to assist in geologic mapping of a major structural zone, the Tijeras-Canoncito Fault System (TCFS). This structure is a very important ore- controlling feature in the area. Geophysical signatures over known deposits was a secondary goal of the survey, but direct detection of mineralization was not anticipated. The TCFS was revealed to be a complex, branching and anastomosing system of faults which locally form the bounding structures of a graben. The geophysical survey guided subsequent geologic mapping by redirecting field investigations, and geophysically redefining some features which previously had been only partly defined.

Jan 1, 1989

By S. K. Singh, J. Shepherd

Feather-edging, a major source of injury and fatal accidents in Australia, South Africa and the United States, refers to a phenomenon in which the roof at the goaf edge falls, often suddenly, as a thin wafer of rock that overrides conventional timber breaker lines. The fall may adversely affect a working bord at a distance of 15 m (50ft) or more from the goaf edge. Feather-edging typically occurs in relatively massive, strong roof strata such as sandstone or conglomerate. This paper presents the results of a test in which a concentrated row of fully grouted bolts were used to prevent feather-edging in an Australian pillar- ("total-") extraction coal mine. The test demonstrated that the bolts could resist feather-edging.

Jan 1, 2000

By Kalyan K. Bhattacharyya

A systematic slope design for open-pit mines has become a reality only in recent years. Advances in the science of rock mechanics, coupled with extensive use of computers, have enabled the numerical solution of slope design problems which were not previously amenable to analytical or numerical solution. This slope stability study was performed for the UJV-SB open-pit uranium mine of the Getty Oil Co., located in the Shirley Basin area, Wyoming. The purpose of the study was to determine the appropriate slope angles for a starter pit. The data generated during the mining of the starter pit would test the initial design and suggest appropriate modification in the design for future mining in the project area. There had been a history of slope failures in the open-pit uranium mines in the area due to the low competency of the overburden materials and adverse hydrological conditions.

Jan 1, 1979

By Reid Trent, Jon C. Volkwein

The U.S. Bureau of Mines is investigating a novel technique to control methane in underground mines by using methane oxidizing microorganisms termed methanotrophs. Coalbed methane has been responsible for many mine disasters and will continue to be a safety obstacle to mining deeper coal seams. Deeper seams of coal contain more methane gas, and better strategies for removing the methane will need to be developed. Methanotrophic microorganisms offer a novel alternative since they physically remove the methane, are commonly found in soils, and already have been found to exist in many foreign coal mines. Proposed applications of this concept include the inertization of buffer zones separating active mining areas from sealed gobs, reducing ventilation from ventilated gobs and reducing methane content from longwall gobs. Current work includes an assessment of the abundance of naturally occurring methanotrophs in U.S. mines, testing the amount of methane that various types of microorganisms can consume, studying the effects or use of the byproduct gases, and finally developing practical appl ications of this biotechnology to coal mining. This paper reports on the initial laboratory testing that measured the quantity of methane consumed by two types of methanotrophic microorganisms. Average rates of methane consumption were between 1 and 4 ml/hour in column flow tests. A possible gob application may require that 750 cfm of methane be consumed during periods of maximum outgassing. It is premature at this time to accurately scale from laboratory to mine application.

Jan 1, 1991

By V. C. Rogers, K. K. Nielson

INTRODUCTION An evaluation of the radiological health risks from uranium mining and milling requires the determination of several key parameters. As shown in Figure 1, the first step is the estimation of the radioactive source term. The radionuclides in the ore consist of the 238U decay series nuclides shown in Figure 2, the 235U series nuclides, and 40K. The 238U decay series isotopes dominate the source term, with the 235U series isotopes causing less concern and 40K remaining at background levels. [ ] Specifically, the risks from uranium mining and milling are mainly associated with 230Th, 226Ra, 222Rn, and its short-lived daughters. These radioisotopes are mainly alpha-particle emitters; hence, some dispersion mechanism is necessary to bring them into intimate contact with man so that they can be inhaled or ingested For water pathways, the leaching of the isotopes from [ ] the solid ore or tailings provides a measure of the amount of contaminant initially available to the environment. For the air pathway, dust-creation mechanisms such as blasting, crushing or general resuspension processes dominate for 226Ra and 230Th. However, 222Rn, being a chemically inert gas generated from the decay of 226Ra, can migrate through the ore, overburden and tailings over considerable distances. As shown in Figure 1, the next step in the pathway to man is environmental dilution and delay. For the water transport mechanism, the delay in the isotopes reaching an accessible water supply may be considerable (several thousand years or more), but for airborne nuclides the dispersion in the atmosphere is rapid and constitutes the main mitigating factor. Considerable ventilation is provided in underground mines to dilute and remove radon and its daughters in order to keep their concentrations low and thereby minimize their inhalation by miners. The rate of uptake by both the workers and the general public is often difficult to ascertain. It involves breathing rates, rates of water consumption and other poorly-defined parameters. The final steps are the risk estimators used to predict doses and cancer rates from the inhaled radon daughters and ingested or inhaled radium. Many

Jan 1, 1981

By James D. Reilly

The time-worn adage "an ounce of prevention is worth a pound of cure" was never more applicable than when used in reference to coal mine safety. Many individuals have dedicated many hours to developing effective accident prevention programs, and much has been accomplished. Each production escalation, however, creates new hazards and safety problems which need special study and research. It is a never ending cyle. To study the progress of coal-mine safety is to raise memories of many individuals who have been dedicated to removing the hazards that have developed with increased productivity and deeper penetration into the earth for coal. Some vivid examples of this dedication are the works of the men who pioneered the use of the safety lamp and the use of rock dust in mining.

Jan 1, 1968

By T. Lupek, S. Plaum

"The execution of classical building services in underground mining operations is more truth than myth. From small concrete foundations for conveyor belts to the construction of huge workshops for large machinery maintenance, nearly every operation requires building services. By creating such fixed facilities, these services ensure the efficiency of the production. A distinction must be made between fixed facilities which directly enable the production and auxiliary facilities which only indirectly support the production. The construction costs of such auxiliary facilities are often roughly estimated because they do not immediately contribute to mineral extraction. The research project ‘Development of a systematic cost-calculation method for building services in underground mines’ seeks to address the question: ‘Can the construction costs concerning fixed auxiliary facilities be neglected e.g. within a prefeasibility study?’ The presentation will show the monetary relevance and significance of these auxiliary facilities and introduce a guideline for cost estimators. PROBLEM DEFINITION The overriding interest of an underground mining operator is to exploit the commodity with the maximal quality by minimum cost and time expenditure. If a new operation shall be installed, it has to promise profitability. Therefore, predictive economic feasibility studies are performed in advance of installation. Herein, all cost expenditure for installation and operation of the future underground mine is determined and compared to the expected income by selling the raw material. The described interest of the mining operator is the starting point of the research project ‘Development of a systematic cost-calculation method for building services in underground mines’. While economic feasibility studies for future operations are focused on the profitable exploitation of raw materials and the efficiency of the accompanying necessary production processes, auxiliary actions are only considered rudimentary. Necessary production processes, as well as auxiliary actions regularly require classical building services, which are normally performed in construction business on the surface in the same manner. By performing building services like masonry or concrete works in underground mines, fixed facilities shall be set up in order to enable or support the raw material production. Production enabling fixed facilities are varying from small concrete foundations for conveyor belts or other infrastructural elements to upstream processing plants situated in the mine workings. While such fixed facilities are essential parts of the production process chain, supporting facilities underground shall increase the efficiency of the mining operation. Workshops, control rooms and social installations are only a few examples for supporting facilities. Those could be situated on the surface as well, but the efficiency increases significantly by installing them underground. Especially supporting facilities are evading from the main interest of the mine operator, since they are only indirectly connected to the production process. The building costs are oftentimes only roughly assumed."

Jan 1, 2017

By Qing Wang, Xiaochuan Xu, Jianping Liu, Xiaowei Gu, Qingyu Zhu

"The ecological costs related to the various optimized production schemes were calculated based on the designed ultimate pit. Moreover, the influence of the ecological costs on the selection of production schemes was discussed. In one designed pit, a series of geologically optimum pushbacks with sufficiently small increment were produced using the floating cone method founded on the principle of the highest metal content. Then all the pushbacks were reordered by the dynamic network diagram. The production scheme with the maximum NPV route was considered as the optimum one. The ecological impacts produced by mining were quantified and the ecological cost calculation models, which contain the direct eco-value loss, the indirect eco-value loss, the eco-restoration cost and the carbon emission cost were proposed. In one big open pit mine case, various production schemes were optimized and the one with maximum NPV was selected without taking into account the eco-costs. The scheme with the maximum comprehensive profit was obtained by calculating the eco-cost of each scheme. The results showed that the best scheme considered with the eco-cost was not the scheme with the maximum NPV. Therefore, the eco-cost presents the effect on the selection of the best production scheme.Introduction Optimizing production scheme is to determine the mining quantities of ore and rock, the pushing position of stope each year, and maximize the NPV of mine. In the theory, production scheming optimization has gone through trial and error (Pana and Carlson 1966), linear programming method (Johnson 1968), mixed integer programming (Gershon 1983), integer mapping (Kim and Cai 1990), dynamic programming et al (Gu et al 2014). In recent years, the study on production scheduling optimization has been focused on two aspects. On the one hand, the study is to solve the investment risk caused by the uncertainties of economic and geological environment (Ramazan and Dimitrakopoulos 2013, Marcotte and Caron 2010, Lamghari and Dimitrakopoulos 2012, Godoy and Dimitrakopoulos 2004, Benndorf and Shishvan 2014). On the other hand, the emphasis of the study was on reducing the problems for the optimization algorithm, to make it more efficient and practical (Cullenbine et al 2011, Shishvan and Sattarvand 2015, Askari-Nasab et al 2011, Nasab et al 2010). However, different production schemes cause different damage of mine land and pollutant emission, thus triggering environment problem. With the improvement of people’s consciousness of environment protection, the environmental issue of mining has been attracting more and more attention."

Jan 1, 2017

By Jim Armbrust

JAMIE DAVIS: Our next speaker is Jim Armbrust, maintenance manager at Phelps Dodge, Morenci. Jim's presentation is titled "We Need More Training-How to Get the Biggest Bang for the Buck." We've talked a lot about preventative maintenance and we've heard several people talk about training. How do we train to use all these systems? How do we educate people? This will be a nice little wrap-up for us. JIM ARMBRUST: One common theme from this morning's talk is that we need more training. That's exactly what we'll be talking about for the next few minutes.

Jan 1, 1998

By Richard J. Adams

Coal jigs have played a predominant role in U. S. coal preparation for fifty years. Recently, an improved fine coal jig has been used to prepare the middle size range coal. These efficient machines are changing the historical thinking about jigs and is consistent with trends in coal preparation throughout the world. The performance achieved and operating cost savings are causing a change in fine coal cleaning strategy. With the exception of a handful of operators, fine coal jigs are generally not well understood by the industry. The objective of this paper is to provide some insight into the past use of fine coal jigs and their potential in the future. Improved Fine Coal Jig Since the mid 701s, an improved fine coal jig has been employed to an important niche in preparation, the 19 mm x 100 M range of cleaning. Several factors due to mining and liberation considerations have caused an expansion of this middle range of coal resulting in a host of challenges for coal preparation engineers. Fine coal jigs have been commissioned in several installations in North America to handle these important applications as shown in Table No. 1.

Jan 1, 1988

By L. Henry Smith, David C. Arthur

The Williams Mine is Canada's largest gold producer, with annual production of 14,000 Kg (450,000 ounces) from 2,300,000 tonnes of ore. Highly mechanized and automated underground mining practices are employed in order to achieve and maintain high levels of productivity and minimize costs. The Mine Ventilation System is modified to include a new Vent Raise and Variable Pitch Vane-Axial Fan. This addition allows several fan installations underground to be decommissioned. A substantial net savings in installed horse power is achieved. Heating costs associated with underground ventilation air are a significant portion of mine operating costs. Air heating costs are substantially reduced by recovering heat from upcast exhaust air, mine water and compressor cooling circuits. This waste heat is used to supplement propane fired air heating systems for underground ventilation air. An additional benefit is the availability of a heat sink for summer cooling of the compressors. System design, energy savings data and payback calculations are presented.

Jan 1, 1997

By Dennis V. D’Andrea, Peter G. Chamberlain, James J. Olson, William C. Larson

Blasts designed for in situ copper leaching must produce adequate fragmentation and permeability for successful leaching. Copper recovery depends to a large extent on the particle size distribution created by the blast, the permeability in the blast- fractured zone, and the ability to maintain solution flow with a minimum amount of channeling. This paper presents the results of Bureau of Mines experiments where core drilling was used before and after blasting to establish the degree of fragmentation. Data are presented from tests at the Sierrita mine of Duval Corp., and also from tests at the Emerald Isle mine of El Paso Mining and Milling Co. Copper recovery is predicted from fragment size distribution data using a computer model. Data from several blasts are used to show how predicted copper recovery is related to powder factor.

Jan 1, 1977

By Peter J. Huck, Yoginder P. Chugh, M. Jennings

INTRODUCTION Large areas of the United States coal reserves have been undermined by room-and-pillar mining over the past century. These abandoned mines generally cause subsidence of the ground surface many decades after mining. Reports from England (1) where there is a longer history of room-and-pillar mining indicate that mines abandoned two centuries ago may still be causing subsidence, and causing surface destruction to urban areas or farm lands that have been developed in the interim. The devastation wrought by subsidence, both in terms of property loss and societal disruption is enormous. The authors discuss here the methods by which subsidence in abandoned mines may be controlled. Two distinctly different subsidence control technologies have been developed in the U.S. for abandoned coal mines. These are referred to as (1) Point Sup- port methods, and (2) Areal Backfilling. As the names imply, point support methods are used to protect individual structures, or even individual foundation elements of structures, whereas areas backfilling techniques may be applied to protect entire neighborhoods or urban districts hundreds of acres in extent. Both point support methods and areal backfilling have specific sub-categories of techniques that may be applied under different conditions as appropriate. POINT SUPPORT METHODS Point support methods are characteristically employed by civil engineers chartered with the design of a new structure or the protection of an existing structure. The subsidence control measures are only a part of a larger project, the safety of which must be assured to a degree of near certainty. The costs of point support methods involve a large number of bore-holes and the use of expensive materials in relatively small quantities. There exist several dozen point support methods, which operate either to support the underground cavities, controlling subsidence, or to isolate the structure from the effects of subsidence if it should occur. The latter methods usually involve deep foundations through the mine opening supporting the structure on the underlying strata. Our concern will be with the former method to support underground cavities to prevent subsidence. Gravel Columns and Associated Methods Gravel columns may be placed in the mine opening using the methods shown in [Figure 1]. Boreholes are drilled through the mine strata, and gravel poured down the borehole to form a pile on the mine floor. When the tip of the pile contacts the mine roof, it is rodded down to spread the pile, and permit additional gravel to be placed. The objective is to place as much gravel as possible in the mine opening, and to achieve firm contact with the mine roof. The gravel pile acts to reduce subsidence by three mechanisms. The filling of a significant fraction of the open mine volume reduces the amount of potential subsidence simply by killing open volume within the mine. In effect, the extraction ratio has been reduced by introducing the volume of gravel. The toe of the gravel pile abuts against nearby pillars, providing lateral support and protection against pillar deterioration. In effect, the height of the pillars has been slightly reduced by burying their lower portions. Finally, some direct support is provided to the roof strata, reducing the roof span and enhancing stability. The gravel column method may be used in a variety of applications, and with materials other than gravel. For example, gravel columns may be placed in a close line around the perimeter of the building to form a continuous gravel wall. The interior of the site may then be completely filled with sand, slurry or other material. Alternatively, a lean concrete may be used in place of gravel, so that the piles achieve significant structural capacity. The grout column, shown in [Figure 2], begins with the installation of a conventional gravel column which is placed around a grout pipe that extends through the borehole into the mine opening. When the gravel column is in place, portland cement grout is injected in stages. At each stage, sufficient grout is injected to fill the interstices in the gravel to build a column perhaps two meters in diameter and a meter tall. The group pipe is then raised one meter, and after the previously injected grout has set, the next stage of grout is injected. The process builds a column of grouted gravel to the

Jan 1, 1982

By Roy E. Williams, Muriel S. Robinette

Ground-water contamination from uranium operations could be avoided with proper site analysis techniques. Contamination from tailings disposal sites is carried downgradient within permeable hydrostratigraphic units which can be located and delineated with a combination of drill holes and borehole geophysical logs. Engineering safeguards can be designed into a disposal site by determining if permeable hydrostratigraphic units exist which will dominate the flow system and provide seepage paths for contaminates. It is more cost-effective to accurately assess seepage potential with geophysical logs before contamination becomes a problem than to be faced with a major clean-up effort after contamination has occurred. If a uranium waste impoundment already has a ground-water contamination problem, then borehole geophysical logs may be used to delineate the contaminated zones which need to be cleaned up. It is less expensive to withdraw the contaminated plume from only within the affected zones rather than attempt to dewater the entire area. Consequently, the geophysical logs are invaluable in assessing which zones should be pumped and where packers should be set for construction of piezometers to allow monitoring of water-quality changes. A surface geophysical technique is being tested and developed for monitoring of seepage frum uranium tailings impoundments. Geoelectric soundings and profiles from direct current resistivity surveys can locate anomalous areas for the placement of drill holes to better assess seepage. This reconnaissance technique should eliminate random hit-or-miss drilling at sites where monitoring is required. Tests and experiments are being done on developing the capabilities of this technique to incorporate complex resistivity data to assess cultural impedence noise which complicates simple resistivity data.

Jan 1, 1980

By J. S. Y. Wang, R. C. Trautz

To evaluate the potential for water seeping into an underground opening, a 9-m- (30-ft-) long drift was constructed in the unsaturated fractured tuff at Yucca Mountain. Forty seepage tests were performed by releasing finite volumes of water at a constant rate into short test intervals located in boreholes positioned above the drift. The seepage threshold flux, defined as the liquid-release flux at and below which water will not drip into the opening, was determined for 10 test intervals. The seepage data, observations and model results indicate that a seepage threshold exists because a capillary barrier diverts water around the opening.

Jan 1, 2002