Search Documents

By Timothy D. Gardner, Christopher Mark

Coal mines in the Illinois Basin have not engaged in pillar recovery for many decades. In large part, this is due to the exceptionally weak nature of much of the roof in the region. But, as room-and-pillar mining is conducted at greater depths, and larger pillars become necessary, recovering them becomes more attractive. Recently a western Kentucky coal mine became the first in recent times to successfully employ full pillar recovery. This paper describes the many challenges that were overcome during the process. From the beginning, the focus was on protecting the miners from roof instability, using cable bolts, mesh, mobile roof supports (MRS), and engineered final stumps. Two short test panels were extracted first, and the results were used to adjust the support pattern and mining sequence. Further adjustments were made based on subsequent experience. To date, seven panels have been recovered without a ground fall injury.

Jul 1, 2023

By D. J. Collins

While the charcoal in pulp (CIP) process was introduced to the mining industry many years earlier, it did not gain widespread recognition until 1973 when Homes take Mining Company installed a CIP circuit at their Lead, South Dakota plant. Since then, a number of mills have been put into production which utilizes activated charcoal for the recovery of precious metals. One of these plants was the Jerritt Canyon mill which Freeport Gold Company commissioned in 1981. It was during the time that the author was employed by Freeport Gold Company that the ideas and concepts presented in this paper were formulated.

Jan 1, 1989

By R. R. Klimpel

The process of froth flotation as a means of upgrading the quality of coal by removing ash/pyrite and of separating selected mineral(s) from undesired gangue materials is certainly one of the most common unit engineering operations in use today. Flotation has been successfully practiced at the industrial scale for well over 50 years, and if anything, its use is increasing due to the ever decreasing feed grades of the coals and minerals being processed. Flotation, as a process, has also shown itself to be an extremely flexible process that lends itself well to a wide variety of solid/solid separations. Thus separations can involve very different particle sizes, particle densities, relative weight ratios of materials to be separated, etc., with surprisingly little modification in equipment and operating philosophy required.

Jan 1, 1988

By T. Wohlford

Due to the increases available base of scientific knowledge, increased independent review required by worldwide security exchanges, and the need for accuracy in characterizing mine water resources, it has become necessary to produce a more accurate hydrologic balance. This presentation provides a critical review of the steps and tools to compile a complete hydrologic review of a mine property. The forces of regulation, increased scientific analysis, better tools, and stakeholder expectations have created a perfect storm of accuracy demand. Ausenco has developed protocol to achieve the desired end.

Feb 23, 2014

In the estimation of recoverable resources, geostatistical techniques such as Multiple Indicator Kriging require a change of support correction to derive theoretical recoveries based on an assumed level of mining selectivity. The change of support models most widely used in practice entail model based generalized corrections either on a global or local basis. Examples include the affine and indirect lognormal methods. Change of support corrections derived empirically through short-scale conditional simulation realizations often show notable differences compared with theoretical corrections determined using model variogram parameters. The existing changes of support models are reviewed and an alternative method is proposed.

Jan 1, 1999

By Alfredo Dammert

The paper presents the results of a model built at the World Bank in order to analyze the aluminum industry. Bauxite demand for the year 2000 is estimated as a function of alumina refineries' requirements and of non-metal uses for bauxite. Bauxite supply by countries or regions depends on economic factors such as investment costs, operating and transportation costs, as well as on tariffs and levies. Various scenarios are considered as a result of varying the assumptions of the model.

Jan 1, 1984

By K. C. Vories, C. D. Elifrits, F. F. Haston

The required reclamation of land disturbed by surface coal mining often results in the creation of some oversteepened slopes that are prone to rapid erosion and sediment production. This natural activity on such slopes is not desirable nor allowed under current regulations. Experience has shown that novel approaches must be devised to address the problem. Research conducted on field sites in Missouri has indicated that construction, during the reclamation and grading processes, of a man-made drainage system will control the erosion. The drainage system must replicate or exceed the natural system in terms of drainage density and channel frequency. Basic design considerations are summarized in this paper, and field results are shown.

Jan 1, 1987

By F. M. Swain

High-calcium limestones occur in the upper part of the New Market Formation, of Lower Middle Ordovician age, in Franklin and Cumberland Counties, Pennsylvania. The high-calcium facies of the New Market Formation is represented by sublithographic limestone or vaughanite, which probably formed in quiet water; low-energy environments such as intershoal lagoons, or in protected bays similar to the present-day Florida Bay environment. Rapid facies changes are characteristic of the strata. The better grade of stone lies in the upper 100 to 125 feet of the New Market Formation and averages 95-97% calcium carbonate. Silica and magnesia are about equal in amount as impurities. One high-calcium belt extends from the Maryland state line through Chambersburg and Newville to beyond Carlisle. The strata in this belt are structurally complex, which requires careful field study' and core-drilling prior to exploitation. Stone suitable for blast-furnace flux is present in relatively large amounts, but stone for open-hearth use or portland cement requires more selective quarrying.

Jan 1, 1966

By D. W. Boening

Xanthate salts have demonstrated effectiveness as a flotation reagent in the recovery of heavy metals from mining wastewater. However, due to their strong ionic potentials, they are generally toxic to aquatic life. Under ambient environmental conditions, the half¬life of a xanthate is approximately four days. As a soluble salt, xanthates will complex with the metallic ions contained in water and fish. Some researchers have proposed that this complexing may extend the halflife, as well as optimizing the transfer of a given metal from solution across the gill surface. Leakage of xanthate treated wastewater into the surrounding surface waters is the most common route of exposure for aquatic plants, invertebrates and fish. Because this is an emerging mineral-recovery technology, more information is needed regarding xanthate toxicity and environmental fate before environmental impacts can be assessed with any degree of certainty.

Jan 1, 1999

By Jaroslaw Drelich

This report briefly reviews the measurements and interpretation of adhesion forces measured between microscopic probes and substrates having micro- and nanoscaled roughness characteristics that were recently conducted at Michigan Tech using atomic force microscopy. The laboratory study concentrated on both rigid and deformable materials, with the probes larger than the size of roughness features of interacting surfaces. For such systems, a detailed surface characterization in terms of roughness parameters, asperity size and shape, and spacing between asperities, as well as analysis of deformation of materials is required. Analysis of the experimental data can be done with theoretical models, which are suitable for rough surfaces and therefore allows to normalize the measured forces. Alternatively, loading of the probe during adhesion force measurements can be managed properly to control deformations of the nano-scaled surface irregularities. Controlling the deformation reduces and even eliminates the effects of nano-roughness on the probesubstrate contact area, promoting conditions described by the contact mechanics models for the sphere-smooth substrate system.

Jan 1, 2005

By Abigail A. Myers, Michael A. Milczarek

Mining impacts to groundwater are being comprehensively regulated for the first time in Arizona with the implementation of the Aquifer Protection Permit Program. This far reaching program is one of the nation's strongest groundwater quality protection programs. Aquifer Protection Pennits (APPs) are required for almost all mining operations and will compel mining companies to pay increased attention to the potential groundwater quality impacts from their activities. All regulated mining operations will have to employ discharge control technologies and monitoring will be heavily emphasized. Technical requirements and relevant permit conditions are discussed.

Jan 1, 1991

By Takashi Sakaguchi, Akira Nakajima

Some attempts were made to recover and remove heavy metal elements, such as uranium, copper and chromium, from aqueous systems by using several phosphate compounds. The phosphorylated derivatives of polysaccharides, chitin phosphate, chitosan phosphate and cellulose phosphate, have high abilities to accumulate heavy metals, such as uranium, copper, manganese, cobalt, cadmium, zinc, nickel and chromium, compared with non-phosphorylated polysaccharides. In order to obtain basic information on the recovery and removal of uranium that may be present in industrial effluents, mine waste water and seawater, the adsorption of uranium by chitin phosphate and chitosan phosphate was investigated in details. The adsorption of uranium by chitin phosphate and chitosan phosphate was much greater than copper, cadmium, manganese, zinc, cobalt, nickel, magnesium and calcium. The adsorption of uranium was very rapid and was affected by pH of the solution, temperature. granule radius and co-existence of carbonate ion. The amounts of uranium adsorbed on the adsorbents increased linearly as the external uranium concentration increased. Uranium adsorbed on chitin phosphate easily desorbed with diluted sodium carbonate solution. On the other hand, uranyl and cobalt ions were separated from each other by using chitin phosphate. Along with these fundamental research, some attempts were made to recover uranium from seawater.

Jan 1, 1993

By Malcolm Scoble

This contribution examines the motivation and prospects for mining companies to become Learning Organizations and integrate Lifelong Learning into their culture. Mining Schools have a potentially central role to play in developing Learning systems for access by industry. Reference is made to initiatives to develop a system that is based on collaboration between UBC, Edumine and the Canadian Institute of Mining, Metallurgy and Petroleum. Recent experiences with this model are reviewed.

Jan 1, 2005

By Muammer Kaya, Derya Oz

The main objective of this study was to remove printing ink from waste newspaper and improve the de-inked paper brightness as close as the unprinted paper by bleaching agents. This paper summarizes results of laboratory investigation into the de-inkability of newsprint printed with offset printing. Different chemicals and process parameters were varied to assess the effect on the brightness and cleanliness. The operations involved in de-inking process are briefly described and some of the problems being encountered are discussed.

Jan 1, 1995

"The Industrial Comminution Efficiency (ICE) working group, part of the Global Mining Standards and Guidelines Group (GMSG) has engaged a large number of industry professionals representing mining companies, equipment vendors, consultants and metallurgical laboratories with interests and capabilities in the comminution field. These participants have collaborated to develop three guidelines for the assessment of the efficiency of mineral comminution circuits. Two of these guidelines deal specifically with power based modelling techniques to quantify energy efficiency using widely practiced techniques, those developed by Bond (1961), Rowland and McIvor (2009), and Morrell (2009). The third guideline deals with the sampling and surveying of grinding circuits as is required to provide the necessary information, at appropriate quality, to furnish the efficiency analysis promoted by the first two guidelines. This preprint will focus on the Guideline on Methods to Survey and Sample Grinding Circuits, which is currently in the final stages of peer review and finalization by the GMSG. INTRODUCTION It is important to make a clear distinction on the scope of work of the GMSG guideline for sampling grinding circuits. Many mineral processing practitioners are familiar with the sampling and surveying of comminution circuits, in particular grinding circuits, for performance diagnosis and the identification of optimization potential. These surveys often provide information for population balance modelling of individual comminution and classification unit processes, and as a result require a large amount of information to calibrate and validate the unit models. As a result these surveys are labour intensive, somewhat expensive depending on internal capabilities of the mine site or company, and have a long time span from initial planning to final reporting. They also require a high level of expertise to process the survey data, simulate the circuit and make sensible recommendations on follow up actions. As a result of these factors full grinding circuit surveys are not a common occurrence at a large number of facilities, and several years may pass before follow up surveys are conducted. In the ensuing gap between surveys, the efficiency of the grinding circuit must often be taken on faith, and this is considered an unacceptable lapse in an environment of strained natural resources and low commodity prices. To support the rapid and productive energy efficiency analysis being promoted by the ICE working group, a much simplified survey and analysis process is required. The process reflected in the GMSG guideline is indeed more conducive to frequent analysis, at a skill level that is well within the capabilities of the average plant metallurgist. As a result it becomes feasible to conduct mini-surveys of plant performance, which can be used to quickly and precisely diagnose the high level impact of process changes. It can also be manipulated by experienced practitioner to provide sufficient information for modelling of the circuit to estimate the impact of process changes, supporting an initial rate and rank exercise to focus plant optimization efforts."

Jan 1, 2016

By T. M. Plouf, G. A. Lang

INTRODUCTION The finding or acquisition of ore bodies containing 200,000 opt gold and greater is becoming more difficult. There are more investors and small heap leach operators who have or can raise the capital to make the investments in the large ore bodies. Echo Bay Mines' approach has been to regionally develop small ore bodies, two or three in the same geographic location, which when considered together contain over 200,000 opt gold. CONCEPT The "world class" ore body syndrome, which many large gold producing companies maintain, can restrict company growth if the finding or acquisition of these large ore bodies is not forthcoming. Another approach has been taken by Echo Bay Mines. The concept is to regionally develop two or three small ore bodies suitable for processing with portable equipment. The systematic scheduling of mining, processing with a single flexible processing plant using the same management/ operator team can reduce your overall investment. The initial selection of mining and crushing equipment suitable for sun11 open pit operations is essential. A very viable option in the mining sequence is to use contract mining/crushing/screening/agglomerating and stacking. This option also lowers your initial capital investment and increases the flexibility in mining as you move from one mining operation to another. LOCATION AND SEQUENCING One single small ore body of itself is not attractive enough for the large producer. The recovery of the initial capital investment, although very rapid, does not make a viable project. The only alternative is to find two or more small ore bodies close enough geographically to each other so that the same management/operator team can be used to run the operations as each is put into operation. Echo Bay Mines has regionally located several ore bodies ranging in recoverable ounces up to 100,000 oz. These small separate ore bodies, located within a 30-mile radius of each other, for planning purposes have been considered as one single ore body. The first small ore body has the initial burden to recover the capital invested in the office, laboratory, power plant and processing plant. Other capital investments such as water supply, access and haul road, fencing, septic system, pads and ponds are reoccurring at each mine site. The first small ore body must recover the initial capital investment in the movable structures as well as the reoccurring capital investment in the fixed structures very rapidly. A total capital recovery time of 6 to 9 months should be used as an economic decision point for both choosing which small ore body should be processed first, and what the plant design capability should be. The sequencing of the small mines is very critical. All the fixed structures mentioned above must be installed at the second mine site before the first mine has been mined out. The ideal sequencing will allow for only one month between shutdown of the first small mine and production from the second. SPECIFIC OPERATION Echo Bay Mines has completed the construction of the Illipah Mine located in White Pine County, Nevada, with this small mine sequence approach. The Illipah Mine is a 40,000 ounce recoverable gold ore body. This ore body met all the necessary requirements. The Illipah project could support the capital investment in the movable structures which will

Jan 1, 1987

By A. W. Khair, M. Ahmad

Bit wear has been proven to have a significant effect on respirable dust generation in coal cutting system. The mechanism of bit wear can be adhesion, abrasion, oxidation, or diffusion, depending on cutting conditions. This paper presents a portion of an extensive ongoing series of studies to better understand the principles of bit wear and dust generation. Used bits collected from underground coal mines were analyzed to identify the basic principle of bit wear in coal and rock cutting. Distribution of weight loss and conical height loss of worn bits were studied and bit wear was divided into four stages according to weight loss. Utilizing these worn bits, Laboratory experiments have been camed out to study the effects of bit wear on coal cutting system and respirable dust generation. An Automated Rotary Coal Cutting Simulator was use to perform the experiments. Acoustic emission monitoring is applied to study the effect of bit wear on fracture formation and dust generation.

Jan 1, 1992

By Jörg Weidemann, Peter W. Kuchar, Paul Burgwinkel

The West German Ruhrkohle AG and the engineering company BEDIA have developed an emission control system for diesel engines that is suitable for use in underground coal mining, consisting of a granular catalytic converter and a dry cooling system. Its first ever application was to a diesel mining locomotive. In the catalytic converter the exhaust gases pass over porous, platinum-covered ceramic balls in a double tube, oxidizing CO to CO2. Simultaneously, soot particles in the gases are subjected to afterburning. Laboratory tests carried out by BEDIA and at Aachen University of Technology showed that there was a reduction of over 80% in the CO content of the exhaust gases and over 30% in soot emission. The dry cooling system fulfills all the requirements demanded of exhaust cooling underground and does not have the disadvantages of conventional systems. It needs little maintenance, and it is light and compact. The most important components are a waterjacketed exhaust manifold, a tube and shell heat exchanger, a new type of flame arrestor in a stacked crimped ribbon design and a Venturi diluter. The system has its own thermostatically-controlled cooling circuit to keep the exhaust temperature between 120° C and 150° C, thus effectively preventing the tubes becoming blocked up.

Jan 1, 1989

By H. B. Oblad

The WEMCO® SmartCell™ flotation machine is a continuously-stirred tank reactor in which solids are suspended in water and are contacted with air. The reaction is particle flotation resulting in the separation of valuable material from gangue. The effects of several operating variables on the flows of water and air and on motor power were measured. A miniature magnetic flowmeter was installed in the draft tube that allowed measurement of the water flows into the rotor. This work has led to a better understanding of machine function which will lead to improved performance and better operation. General equations for optimization, design, and scale-up were inferred.

Jan 1, 2002

By J. Bilant, B. Carlson, N. Gow

High Pressure Grinding Roll (HPGR) technology has been evaluated to replace tertiary cone crushing at Coeur Rochester operations (Coeur Rochester, Inc.) as an opportunity to improve silver recovery. In 2016 and 2017, onsite and third-party pilot programs were initiated to evaluate the impact of metallurgical recovery and heap leach performance of crushed product generated by an HPGR. In 2018, Forte Dynamics evaluated the HPGR laboratory metallurgical data from Coeur Rochester and all third parties to develop field-scale leach curves based on new crushing scenarios. The laboratory recovery test work data was consolidated and scaled to field conditions to determine projected heap leach performance. Based on the metallurgical testing conducted, the replacement of current tertiary cone crushers with HPGR technology has the potential to increase Coeur Rochester’s silver recovery rate by 8%, from 61% to 69%, and shorten the overall timing of silver recoveries from 20 years to just over two years. INTRODUCTION The Rochester mine, and associated valley fill heap leach facilities is an open-pit silver and gold mine located in Pershing County, Nevada, approximately 26 miles northeast of the city of Lovelock. In 2017, Rochester produced approximately 4.7M troy oz silver (Ag) and 51k troy oz gold (Au). Ore mined at Rochester is either fed directly to the primary X-Pit crusher, crushed at an in-pit crusher system, or placed directly onto a heap leach pad as run-of-mine (ROM). Both crushing circuits are comprised of three stages of crushing to produce a nominal 3/8” ore. Primary crushing consists of jaw crushing while secondary and tertiary crushing are composed of varying cone crushers. Historical recovery rates of crushed Rochester ore average 61.4% Ag and 95.9% Au over a period of 20 years [1]. These rates were derived from third party verification of in-house metallurgical test results, crusher production and heap leach production results from 1986 through 2004 in a private report for Rochester produced by KD Engineering Co., Inc. Recovery rates are regularly verified by compositing daily samples of ore delivered to each leach pad from the X-pit crusher, in-pit crusher, and/or ROM. A proportionate split of each sample is used to generate monthly composites for metallurgical analysis utilizing column leaching and bottle roll leaching. These tests are run in a manner analogous with production conditions and deliver test results that provide expected heap leach performance. As the Rochester oxide deposit has been mineralogically and metallurgically consistent, the gold and silver recovery trends have also been consistent over the life of the project. In 2016 and 2017, onsite and third-party pilot programs were initiated to evaluate the impact of HPGR technology to metallurgical recovery and heap leach performance of crushed product in an open circuit configuration, as a potential replacement for the currently in place tertiary cone crushers. During these years, HPGR was evaluated in three phases of test work.

Jan 1, 2019