Search Documents

By William H. Meadows

This information describes the ventilating and methane gas testing procedures utilized during the raising of a mine shaft using a Robbins 81-R drill. An overview of the raise boring process is presented to illustrate the ventilating and gas testing procedures. A mine shaft project, 4.88 m (16 ft) in diameter and approximately 457.2 m (1500 ft) in length, will be the focal point of the presentation, with reference to similar projects for additional comments on variations in procedure.

Jan 1, 1980

By L. Diestelow

Evaporation and crystallization processes are used extensively in the mining industry to provide many pro-ducts. In the case of solution mining evaporators are used to concentrate, or to concentrate and crystallize the raw materials being mined. In the case of underground, or strip mining dissolving and crystallization are used in many processes in order to purify the ore to saleable materials. Presently evaporators and crystallizers are being used in the production of sodium chloride, potassium chloride, sodium carbonate, sodium sulfate, lithium chemicals, aluminum, and many others. The evaporator is a device designed to remove water or solvent from a solution. In an evaporator the energy released by steam condensing on one side of the heat transfer surface is transferred to the product solution on the other side of the heat transfer surface. As long as the boiling temperature of the product liquor is below the condensing temperature of the steam, the product solution will absorb heat. This heat absorption causes vaporization of the water (solvent) in the product solution resulting in concentration of the product. The simplest evaporator is the single effect evaporator. If we assume the feed introduced into the single effect evaporator is at its boiling point, ignore radiation losses, and assume the steam into the heat exchanger is dry and saturated, then the heat transferred will correspond to the latent heat of vaporization. Therefore, one kilogram of condensing steam will produce one kilogram of evaporation. Economies in energy usage compared to the single effect evaporator can be made by using multiple effect evaporators, or vapor recompression evaporators.

Jan 1, 1993

By Juan P. Camus

One of the most important decisions in mine development is the selection of the mining method. Open pit or underground methods are selected depending on the shape of the deposit, and its position with respect to the surface. When the decision is not clear or evident, then the common rule is to compare underground and open pit projects to choose the one which yields the maximum return. However, in some circumstances' the best alternative is to start-up the operation with an open pit until a point where mine operating costs make more convenient to employ an underground method. In this case, the final pit limit is not directly related with commodity prices and its position is a funtion of capital and operating costs associated with both methods. The goal of this paper is a mans of establishing the proper ultimate pit considering a potential underground mine. The methodology is quite simple and can be implemented to work with a variety of available routines for pit optimization, such as Lerchs-Grossmann, floating cone, network flow and the Lemieux moving cone optimizing algorithm, which is the tool used by the author.

Jan 1, 1992

By James L. Vanderbeek

INTRODUCTION Semiautogenous (SAG) grinding technology first started to be seriously considered for comminution circuit design in the mid-1960s as an alternative to the three-stage crushing circuits and rod-ball mill circuits in vogue at the time. Since this time the application of SAG mill technology has become widespread with over 250 mills larger than 20 feet in diameter sold (Jones 2002). The vast majority of concentrators constructed over the past quarter century have utilized SAG mill technology, and a SAG-based comminution-based circuit is generally the first choice considered for new projects. Since the first generation of SAG milling technology was applied, many lessons have been learned, and new supporting technologies have emerged which make the design, installation and operation of SAG &-based grinding circuits more robust and efficient. This paper will discuss the current status of SAG and associated technologies. MILL MECHANICAL DESIGN ISSUES Table 1 summarizes the manner in which SAG design capability has evolved over the past 30 years. Increases in mill diameter came slowly as the industry took a wait-and-see attitude as the technology of larger mill diameters was advanced. The first 32-foot- diameter mill was ordered in 1969. It was not until 1979 that the technology jumped to the 34-foot-diameter mill and 1988 for the first 36-foot-diameter mill. The first 38- and 40-foot-diameter mills were both ordered in 1996. At least five 38-foot-diameter and two 40-foot-diameter mills will be in operation by mid-2004. Advances in structural analytical techniques and increased computational power, coupled with field measurements of large operating mills, have increased the confidence of the mill suppliers in their designs and the operating companies in the viability of larger diameter mills. No failures of a 36-foot-diameter mill or larger have been

Jan 1, 2004

By Martha Caudill

When planning for the required amount of storage capacity at a proposed open-pit coal mine or determining when additional storage capacity should be added to an existing operation, the decision must be based on a breakeven- analysis relating the discounted cost of capital for storage capacity to the marginal costs incurred for additional crew call-outs on weekends and demurrage charges. The model developed in this paper uses simulation techniques applied to two coal mines in the Powder-River Basin to determine how much storage capacity is needed and when it is needed. The paper also generalizes the simulation model so that it can be applied to any type of open-pit mining operation. Two important results of the model are (1) all of the mines in the Powder River Basin have excessive amounts of storage capacity, and (2) management is provided with estimates of the total number of hours that crews will have to work on the weekends as annual tonnage increases, and the levels of demurrage costs incurred.

Jan 1, 1986

For processing plant design it is essential to develop a consistent material and (usually) energy balance as a basis for equipment sizing. This paper discusses techniques for consistent material balance generation, from hand calculation, through spreadsheets to specialised computer programs and general purpose simulations. The appropriate matching of techniques to problem complexity is considered, as are some possible trends for the future.

Jan 1, 1991

By Josiah Pohl, Christopher Utter, Kyle Everly, Akshay Chowdu

Battery Electric Vehicles offer increased energy efficiency for open-pit load & haul operations at a potentially lower overall carbon cost. Electrifying a mine’s fleet, however, presents a unique set of operational challenges. In this study, we explore the effects of electrification on productivity at real operations using a Discrete Event Simulator. The model can simulate multiple shifts, a mixed fleet of diesel and electric trucks, charging and refueling stations, trolley systems, and accurate shovel-truck loading cycles. This study helps determine the trade-offs of adopting electric fleets and how they interact with the layout of today's mines.

Jun 25, 2023

By Robert V. Price

It is a pleasure to be here today to discuss coal's prospects with the Society of Mining Engineers of AIMS--- a group destined to play a crucial role in shaping our national energy future. Much has been said lately about attaining domestic energy self-sufficiency, but to date, little has been done. Oil tankers from Venezuela and Kuwait continue to glide across the seas to meet our incremental energy needs. Meanwhile, our principal domestic energy resources -- oil and natural gas reserves in the Outer Continental Shelf and the oil shale deposits and the coal lands of the West -remain untapped. Help, however, appears to be on the way. In a forceful address last fall, President Ford called for the elimination of oil as a fuel for base-loaded power plants and its replacement with coal by 1980. He also urged the accelerated leasing of federal lands on the Outer Continental Shelf, the resumption of coal leasing on federal lands, and the development of a new energy conservation policy. There are, of course, many details left to be worked out. Language must be developed to put statutory flesh on the conceptual bones spelled out by the President. Congress must act. Regulations must be approved and tested, if need be, in court.

Jan 1, 1975

Numerous underground coal mine ventilation seals have been installed in the United States of America prior to 2006 and after implementation of the Mine Improvement and New Emergency Response (MINER) Act. Seal engineering, design, placement, and construction is regulated in industry, but post-construction monitoring of seals is limited to visual inspection of the outby face and seal perimeter, convergence measurement, and atmospheric monitoring. To monitor seal integrity and to provide safe working conditions, a form of non-destructive testing (NDT) is necessary to accurately reflect the health of the seal by detecting post-construction changes, deterioration, or defects within in-situ seals in underground coal mines. Previous research from the National Institute of Safety and Health (NIOSH) has indicated the potential for utilizing ground penetrating radar (GPR) for assessing in-situ mine seals. This paper provides an update to the assessment of proposed NDT methods for seal evaluation using commercially available GPR technologies and systems. Full-scale free-standing seals and large-scale seal specimens were analyzed with an array of GPR units from various manufactures using multiple frequencies.

Feb 23, 2014

By J. R. Blair, D. P. Lindroth, W. R. Berglund, R. J. Morrell

The objective of this US Bureau of Mines (Bureau) research was to determine the technical feasibility, principles and effectiveness of a combination energy method for drilling and cutting hard rocks. Experimental test results of microwave heating and drilling in basalt and granodiorite are given. The experiments were performed with pilot-scale, commercially available equipment employing microwave energy at a standard industrial frequency of 2.45 GHz. The data indicate that penetration rates, well in excess of the state of the art, are possible.

Jan 1, 1993

By C. J. Webb

Column experiments were performed to determine the ability of Madison aquifer material to adsorb arsenic and other constituents in a heavily mined watershed of the Black Hills in western South Dakota. The Madison aquifer is a karstic dolomite and limestone reservoir that is exposed on the flanks of the Black Hills. Streams that cross the Madison in the eastern Black Hills typically lose all their flow to the aquifer at sinkholes. In this work, Madison aquifer material was obtained for loading of six-inch diameter columns, which were backfilled with Madison aquifer water. Stream water then was allowed to displace the aquifer water during column testing in order to simulate mixing of the two waters at sinkholes and to determined adsorption of arsenic and other dissolved constituents. Initial results show that some adsorption of arsenic occurred when compared to more conservative tracers such as nitrate.

Jan 1, 1999

By Jamal Rostami

With the recent technological advances; Tunnel Boring Machines (TBM) have become a viable economic alternative to drill and blast in hard rock excavation. These machines are finding increasing use in underground mine development due to the potential benefits they offer. The successful application of TBM technology to mining depends on the selection of the most suitable equipment and cutting tools for the rock and ground conditions to be encountered. In addition to required testing and geotechnical investigations, cutterhead design optimization is an integral part of the machine selection to assure a successful application of the machines in a specific project. This paper presents and discusses the back-ground of TBM application in a mining environment and the lessons learned, the process of conducting site investigation and the necessary laboratory testing together with machine selection and performance estimation for TBM use III mine development.

Jan 1, 1997

By C. Clark, J. Johnson, M. Stepan

"Shotcrete and mesh are often installed to control ground deformation, falls and ejection between bolts. The combination of mesh and shotcrete forms a panel or plate that is typically bent by ground extruding between restraining rockbolts. The ground pressure applied (that is, the resistance of these panels to bending) over large ground deformations is important for maintaining ground support safety. This paper describes a new test device that measures this resistance and its evolution over large deformations. Mixes of shotcrete, mesh and other components that can maintain significant support pressure are desired, a characteristic described as the “toughness” of support. Results show toughness depends largely on how shotcrete is integrated with other components. Shotcrete strength is less important. INTRODUCTION Ground control safety often depends on supporting, or at least containing, the ground between the rockbolts. Shotcrete and mesh, in various combinations and with other components, are often called upon to do this (Figure 1). Applications are especially common in mines with squeezing ground or seismic loading. The support pressure maintained during ground deformation is key to the performance of these systems, and to protecting miner safety. However, the toughness of a design is difficult to estimate. Researchers at the Office of Mine Safety and Health Research (OMSHR) responded to this deficiency or “gap” by designing a full scale test device, described in this paper, and beginning a testing program. Some initial results from this program are reported to demonstrate test capabilities.BACKGROUND - TOUGHNESS Mining in ground that fails from the combination of in situ and mining induced stress is commonplace. Ground support elements are installed to reinforce such ground and preserve mine safety. Typically, the strength of support is considered key, and is used to prevent or halt yielding. However, ground movements driven by creep of weak ground or seismic loading may be impossible to halt altogether. In these cases, it is essential that support is able to yield with the ground in a safe manner while maintaining confining pressure that mobilizes the strength of rock in the immediate perimeter of the opening. In addition, it’s usually desirable to contain ground between rockbolts to protect miners from loose rock that might fall or be ejected. Shotcrete and screen are often employed, sometimes together and in combination with other support elements, to accomplish this function. A key characteristic of such a system is its ability to maintain support pressure through large ground deformations, a characteristic often called “toughness” – especially in support systems incorporating shotcrete. Toughness can be quantified as the work done during deformation (e.g. force x displacement)."

Jan 1, 2015

By Wayne J. Nordstrom, Dennis L. Murr, James E. Wennen

National Steel Pellet Company (NSPC) conducted pilot scale testing and computer simulation studies which indicates that the capacity of the secondary grinding mill could be increased and that concentrate grade improvement could be expected with improved classification in the grinding circuit. Based on these studies, a decision was made to modify one secondary ball mill line at NSPC to include both cyclone and screen classification with magnetic separation applied to the circulating load. This paper will briefly discuss the studies leading to the decision to modify the circuit, the design of the modified circuit and the initial start-up and operating experience.

Jan 1, 1997

By Margaret Armstrong, Chris Roth

One advantage of kriging is that it provides both an estimate of the block or point grade, and an indication of the local precision via the kriging variance. If one assumes that the estimation errors are normally distributed, then confidence intervals for the grades can be calculated. But in mining, grades are rarely normally distributed; in general, they are skew. This is particularly true for precious metals. In this paper we study confidence intervals for variables with non-normal distributions. Using a non linear geostatistical technique, the grades are transformed into their normally distributed equivalents. Confidence intervals are obtained for these normal variables, and back transformed to give the corresponding confidence intervals for the grades, for either points or blocks. This approach is applied to gold data from the Witwatersrand basin in South Africa.

Jan 1, 1996

By S. Acar, P. Somasundaran

Results of selective flocculation of natural ores containing two or more minerals and of synthetic mineral mixtures do not usually agree with what is expected on the basis of the results from single mineral tests (Acar and Somasundaran, 1985). This is mainly due to the ionic species released by the minerals, which act differently under different pH values. The objective of this investigation was to study 1) the surface chemical composition of selected sulfide minerals-natural chalcopyrite and pentlandite and synthetic covellite, millerite, and pyrrhotite-and 2) the changes brought about by the dissolved mineral species. Electron Spectroscopy for Chemical Analysis (ESCA) was used to perform the surface analyses.

Jan 1, 1991

By J. F. Fitzpatrick

This paper examines the cost elements associated with changes to gold mining practice over the last decade that result from the changes in environmental regulation and the heightened governmental and public awareness of environmental issues. The main experience base is Pegasus Gold Corporation's flagship mine, Zortman/Landusky, located in the Little Rocky Mountains of Phillips County, Montana. This operation was among the first mines that were permitted under the 1974 Montana Metal Mining Reclamation Act. In 1974, the Montana Metal Mine Reclamation Act was enacted, creating a permit system for metal and industrial mineral mines for the state of Montana. The act established the content of mine permit applications and defined parameters for the reclamation of mining disturbances. The Act can be viewed as implementing legislation for Article 9, Section 2, of Montana's Constitution, which provides that "all lands disturbed by the taking of natural resources shall be reclaimed." Pegasus Gold Corporation's Zortman/Landusky mine was among the first mines permitted under the new Act. In 1978, the initial permit applications were submitted for Zortman and Landusky, and a full Environmental Impact Statement was prepared by the Montana Department of State Lands; permits were issued in 1979. When opened later that year, the anticipated mine life for the combined Landusky and Zortman operations was approximately 18 years, based upon a proven and probable ore reserve of 43.2 million tons. Zortman/Landusky was the first large-scale heap leach gold mine in the United States. Its distinguishing feature was, and remains, a remarkably low ore grade, now .016 oz/ton. The ore is economic because it requires neither crushing nor agglomerating to leach effectively. Approximately two years after the initiation of the state's regulatory process, the Federal Land Policy Management Act (FLPMA) was enacted, establishing a mine regulatory framework for lands under the administration of the Bureau of Land Management.

Jan 1, 1992

By S. B. Patton, T. Novak, R. L. Sanford

A comprehensive approach to the development and organization of an expert system designed to assist electricians in diagnosing electrical faults in mining machinery is discussed. The system includes diagnostic, reference, and tutorial programs. The diagnostic portion of the system is based on a causal-reasoning approach, which is used to establish a hierarchy of symptoms and the subsequent production rules for identifying component-level failures in the motor-control circuit of a shuttle car. With this approach, conclusions are developed directly from knowledge of the circuit and its behavior (in both working and failure modes) based on first principles, rather than the heuristics of a domain expert. The symptoms and their hierarchal structure are formulated by creating "what if' scenarios and performing a qualitative circuit analysis for each fault. Techniques for incorporating interactive graphical displays of the circuit schematic into the diagnostic portion of the system are also presented. Supportive computer programs that provide reference material and tutorials on the circuit are also described.

Jan 1, 1990

By Persio de Souza Santos, Ayres Ferrelra Morgado

In this work, a sample (of about 100kg) of an ore considered as smectitic, not yet industrialized, from Lages-SC-Brazil, was tested for evaluation of its industrial applications. First, we characterize them by XRD, DTA, FRX, and CEC analysis. After this, the smectitic clay was changed to sodium form by treatment with sodium carbonate. Then, the homoionic sodium clay was tested for iron ore pelletizing agent, as binder of foundry sands, and drilling mud with good results.

Jan 1, 1998

By Yi Luo

A massive roof fall occurred in a small room-and-pillar coal mine. The roof falls occurred under a barrier pillar in a closed coal mine located a short distance above the active mine. The extensive fractures connected the active mine with the old mine, turning them into a “combined mine.” Since completely sealing off the roof fall area is prohibitively expensive for the mine, ventilating the connected old mine became the only option. A comprehensive investigation was conducted to understand the atmospheric condition in the old mine and to find an efficient way to ventilate the “combined mine.” A set of studies involving geology, gas content, pillar stability and mine subsidence were performed to explore whether the closed mine is filled with an explosive air-methane mixture. The air quantity measurement data were used to determine the resistance of the air path formed through the fractured zone. Observations and measurements made from a tour to the underground and mine surface enabled the formulation of simple but effective ways to ventilate the old mine. The ventilation network analysis also suggested methods of control, so that sufficient ventilation air can be directed to the two parts of the old mine.

Jan 1, 2010