Search Documents

By Steven J. Luzik

Introduction From 1973 through 1986, a total of 12 fires involving oil-flooded rotary screw compressors (OFRSC) were reported to the Mine Safety and Health Administration (MSHA). Most of these incidents were attributed to faulty or by-passed safeguards, or improper maintenance. The cause of a fire in an OFRSC is unique when compared to other types of compressors. A compressor inspection checklist is provided here that can be referenced when conducting regularly scheduled maintenance operations. This checklist and a well-planned program of periodic training and maintenance should help minimize the probability of fires and explosions in OFRSC's. Operation A rotary screw compressor operates on the principle of positive displacement of air. Compressed air in this type of compressor is produced by the meshing of two helical rotors, or screws, as they rotate within a steel housing called a stator. The male rotor normally has four lobes and is driven either directly or indirectly - through a gear assembly - by a motor. It intermeshes with a female rotor having six cavities. Figure 1 explains the compression mechanism: (1) Atmospheric air is drawn into the stator by the suction action of the two rapidly rotating rotors. (2) As the rotors rotate past the intake port, air is trapped in the stator and in the cavities between the rotors. (3) Further movement of the rotors causes an increased reduction in volume, compressing the entrapped air. (4) Compressed air is expelled at the discharge port in the bottom of the stator at a pressure and quantity determined by the particular compressor rotor design parameters, such as length, diameter, and speed. Radial bearings on the male and female rotors compensate for radial loading on the shaft and position the rotors within the stator. Thrust bearings on the discharge end of the compressor prevent rotor misalignment due to thrust developed during the compression cycle. This design prevents the male and female rotors from making contact with each other or the stator. A clearance of 0.07 to 0.1 mm (0.003 to 0.005 in.) exists between the two rotors and the stator. For this reason, there is virtually no wear on the rotors or stator, and the unit is relatively maintenance-free. Oil is injected into the compressor and serves to cool, seal, and lubricate. When air is compressed from atmospheric pressure to some higher discharge pressure, a specific amount of heat is produced. This heat is sometimes referred to as the adiabatic heat of compression. It is partially removed by injecting oil into the compression chamber. Premachined strips - a raised surface on the male rotor and a

Jan 9, 1988

By A. E. Aldrich

The Pittsburg & Midway Coal Mining Co. (P&M) is expanding a combination of surface and underground coal mining operation in Northeastern New Mexico. The York Canyon Complex, located 35 miles west of Raton, New Mexico, is aggressively pre-paring for increased production while meeting present requirements. Surface mining activities in four separate mining areas are preparing the complex for additional markets. Drag-line, truck/shovel, highwall miner and contour stripping are surface mining methods currently planned. In addition, P&M will move a Marion 8200 dragline from Kansas to the York Canyon site, finish constructing a $20 million coal preparation plant, and complete conveyor upgrades to the existing underground mine. This paper will describe the diverse York Canyon Complex.

Jan 1, 1993

By R. C. Guimareãs

Serrana's deposit contains three types of ore: oxidized, micaceous and silicate-carbonate. The results presented refer to characterization and fundamental studies performed on fractions resulting from the purification of five samples from the silicate-carbonate type collected in the mine. Each type was purified and submitted to mineralogical characterization, zeta potential determinations, and microflotation experiments. The samples, with exception of the barite, are mineralogically complex and the selectivity between apatite and gangue minerals is poor. Under the current state of art, it is impossible to feed the plant with the silicate-carbonate ore, unless it is blended with the standard oxidized ore.

Jan 1, 2002

By Felicia F. Peng, Victor Z. Sun, Syd S. Peng

A probability-based analysis method in conjunction with the finite element structure modeling technique to evaluate an entry system stability is developed. Variability of the rock properties and loading surrounding the entry system is taken into consideration to predict a roof stability by using the probability of failure instead of the common safety factor concept. A dynamic programming is applied to establish a recurrence relationship between the degree of potential roof fall and accumulated roof fall index in an area of interested. A probable distribution of roof fall is assessed by using a developed computer program, RFSTAB. The assessment of the roof falling boundary in the longwall entry system is used as the example to illustrate the procedure and effectiveness of this analysis method

Jan 1, 1996

By Seung Han Kim, Andrew Yu, Carlos Jaramillo, Chu-Chieh Jay Lin

The Penstock Access Tunnel (PAT) concrete plug is a reinforced concrete plug separating the pressure tunnels from the personnel accessible tunnels and has leaked since the first filling at the Helms Pumped Storage Plant located in Fresno County, California. A grouting program was successfully implemented in 2009 to reduce the leakage from PAT concrete plug from over 1,000 gpm to 25 gpm. Recent observations indicated increasing water leakage through new pathways, leading to a decision to execute a high-pressure grouting and waterproof membrane installation program in 2017. The high-pressure grouting and membrane installation program was successfully executed in the areas adjacent to the PAT concrete plug where most of the inflows originated and the largest hydraulic gradients are suspected to present. It reduced the leakage from over 300 gpm of inflow to less than 20 gpm.

Jun 13, 2021

By Kenneth A. Gutschick, Harry L. Francis

A large number of minerals and chemicals (Table 1), some mineral-derived, are used in the treatment of both potable water and domestic sewage waste water and solids (Anon., 1990). In water treatment there are ten principal process uses as shown in Table 2 (Anon., 1990), which also lists the major chemicals in each process. Since lime (calcium oxide, calcium hydroxide, and dolomitic lime) is the largest chemical (by tonnage) used in water treatment, this chapter will deal primarily with this product. Note that it is included in five of the process uses shown in Table 2, and that indirectly it is also used in at least one other category (taste and odor control, where lime is used with potassium permanganate to provide optimum pH condition). POTABLE WATER TREATMENT Water Softening The biggest use for lime in water treatment involves water softening, where it serves to reduce carbonate hardness caused by dissolved bicarbonate and carbonate compounds. Currently there are more than 1000 domestic water softening plants (Table 3) located in most sections of the country, but particularly in Ohio, other midwestern states, Florida, and Texas, where limestone bedrock abounds (Anon., 1990). Among the other uses for lime in water treatment are coagulation, disinfection, and removal of heavy metals due to high pH softening, removal of certain radioactive and organic compounds and fluorides, neutralization of acidic water, removal of silica, particularly with dolomitic lime, and removal of color. Most of the above advantages accompany water softening, although at some plants lime is used specifically for one purpose, such as silica removal with dolomitic lime, minimizing pipeline corrosion by addition of lime to correct an aggressive water, and others. Hardness in water comprises two types - carbonate hardness, caused by dissolved calcium and magnesium carbonates and bi- carbonates, and non-carbonate hardness caused by dissolved non- carbonate salts, particularly calcium sulfate, calcium chloride, magnesium sulfate, and magnesium chloride. Total hardness is the sum of the carbonate hardness and non-carbonate hardness. Waters are classified as soft (0 to 75 mg/L as CaCO,), moderate (75 to 150 mg/L), hard (150 to 300 mg/L), and very hard (above 300 mg/L). Most water plants strive to reduce total hardness to about 100 mg/L, although in recent years the tendency in some cities has been to allow a little higher value in order to reduce both chemical costs and the amount of water softening sludges produced. There are four basic types of softening plants: lime softening, primarily to reduce carbonate hardness; lime-soda softening, for reduction of both types of hardness (in some plants caustic soda is used in place of soda ash, but it is more costly); split lime-zeolite, where a base exchange mineral is employed in place of soda ash (this system also requires salt [sodium chloride] to regenerate the zeolite mineral); and finally zeolite softening, which is generally used in small systems for private houses and small municipalities. Principal disadvantages of the latter system are its relatively high cost and the salt requirement, which introduces considerable quantities of soluble salts into the waste water discharge system.

Jan 1, 1994

By Dennis P. Bryan

The southwestern United States has an abundance of natural lightweight aggregate (NLA) deposits of volcanic origin that are being used in the construction industry within the region. New Mexico, Arizona, Nevada and California utilize NLA in portland cement concrete and concrete masonry units for weight reduction and related economic reasons. The geological environment of the western United States is amenable to the occurrence of natural lightweight rocks because it contains Tertiary and Quaternary volcanic products that include low-density glass and vesicular material. There are two major classical types of natural lightweight materials of igneous origin; pumice and cinder. These account for the vast majority of volcanic rocks that are presently utilized as NLA. Pumice is an ejecta product generally found as part of tuffaceous units associated with nearby siliceous volcanic centers. Cinder, also an ejecta product, is associated with mafic volcanics and is most often found as a cinder cone. Both are highly vesicular. A third type of natural lightweight material, though also associated with siliceous volcanics, is less vesicular than pumice. It is best described as being a slightly pumiceous rhyolite or rhyolite-tuff breccia that occurs as a siliceous dome or tuft unit that is most likely to be glassy. Uses of these natural lightweight rocks center on the construction industry where they are utilized in lightweight portland cement concrete and lightweight concrete masonry units. The major reason for usage in portland cement concrete is cost saving effected by weight reduction in high-rise construction. The major usage in concrete masonry units, or "block", is for weight reduction that enables a mason to lay more lock.

Jan 1, 1987

By M. R. Rosen

CARBINDER Polymer 498 is a liquid organic taconite binder which significantly improves fired compression in both fluxed and acid pellets. It has been used commercially in both shaft and straight grate furnaces. This new binder produces an unusual wicking phenomenon during balling wherein the rate of movement of interstitial water is accelerated to the surface of the balls. The phenomenon is proposed to be responsible for the significant improvement seen in fired compression. This paper presents information as to the effect of CARBINDER Polymer 498 on green ball and fired pellet properties. It also describes the wicking phenomenon and discusses a reversal in the normal balling operation procedures required for successful agglomeration.

Jan 1, 1988

By A. MacG. Robertson

Where weak rock zones are encountered in the slopes of an open pit, they may control pit wall stability. Back analysis of slopes involving failure through weak rock enables an estimate to be made of the weak rock strength. A system of consistent rock mass classification is described which enables the weak rock mass material to be described and classified from drill hole core. Correlation with back analysis determined strength allows strength estimates to be assigned to each rock mass classification.

Jan 1, 1988

By J. Litsenberger, T. E. Marshall, P. R. Coyle, L. J. Prosser, A. T. Iannacchione

For the first time in an underground stone mine, the relationship between roof movement and microseismic emissions was examined in conjunction with two distinct roof fall areas. As roof monitoring increases in acceptance and monitoring technology advances, the goal of providing reliable roof fall detection systems to enhance the safety of underground mine workers moves closer to reality. Instrumental to reaching that goal is the ability to interpret accurately and completely roof movement and microseismic emissions, which can serve as precursors to roof falls. This paper examines the capabilities of convergence and microseismic monitoring systems to better understand roof rock failure mechanics and to anticipate roof falls. An understanding of how these techniques are used and how they interact with each other is critical in developing the most effective ground control strategy for our nation’s mines.

Jan 1, 2004

By D. T. Kinard, A. A. Schweizer

An operational 9 meter (30-foot) high gold heap leach pile was investigated by excavating test pits up to 6 meters (20 feet) deep, obtaining bulk and relatively undisturbed thin wall drive samples, and observing the ore distribution patterns exposed in the test pit walls. The clayey ore is crushed, agglomerated with lime and cement, and deposited on the leach pads using a radial stacker. Laboratory tests performed included moisture-density, gradation, compaction, Atterberg limits, permeability (constant and falling head), and triaxial strength tests. Discussion is presented on the effects of agglomeration on the permeability and strength characteristics of the in-place ore. Also discussed is the effect of deposition of the ore using the radial stacker.

Jan 1, 1987

By S. K. Kawatra

Although temperature is known to have a substantial effect on many processes, this parameter has been widely dismissed as insignificant for mineral comminution. For this reason, temperature effects on grinding have largely escaped notice. However, it has been observed that processing plants which are subjected to large seasonal temperature variations show a change in performance which appears to be due to changing feed temperatures. The general effect is an increase of the specific energy consumption as the temperature decreases. In autogenous mills, an increased rate of production of critical-size material has also been observed. This is due, at least in part, to changing rheological conditions in the mill, with the slurry viscosity increasing markedly at low temperatures. Mechanical changes in the rock with temperature, such as increased brittle fracture, is also responsible for a portion of the observed seasonal effect, and may account for this phenomenon being observed only in certain plants.

Jan 1, 1989

By R. T. Swinderman

This paper discusses how many of the common practices in conveyor specification and design are out of date compared to the current expectations of users for safe, serviceable, reliable, and fugitive material-free conveyance of bulk solids. Ten of the most common mistakes made in the specification and design stages related to user expectations are reviewed along with the cost vs. price implications of those decisions. A general specification and design hierarchy that designers can use to improve conveyor design is included.

Jan 1, 2010

By Jun Li, Marc Le Vier, Rong Yu Wan, Jan D. Miller

The hydrometallurgical treatment of gold and silver ores by ammoniacal thiosulfate solutions in the presence of a copper catalyst has been actively studied in recent years. Such a process strategy is very attractive due to the low toxicity of the lixiviant and the efficient recovery of the precious metals from difficult-to-treat ores. Important features of the ammoniacal thiosulfate system for the recovery of precious metals from various sources are reviewed in this paper, including leaching, metal recovery, and system stability.

Jan 1, 1995

By J. J. Moore, B. Mishra, D. L. Olson

The production of radioactive and reactive metals, such as plutonium, uses various pyrometallurgical techniques that generate significant quantities of waste salts contaminated with hazardous, reactive or radioactive materials. Health concerns, environmental regulations and economic considerations require proper mitigation processes to recover the valuable components and for recycling or unrestricted release of these salts. The Oxygen Sparging Process converts soluble metal halides, such as chromium-, plutonium-, cerium chlorides, into insoluble oxides and/or oxychlorides which can be consolidated and separated for long-term storage or further processing. The matrix salt phase, viz. calcium and/or alkali chlorides, are clean after oxygen sparging and fit for recycling. This method has been described and its optimized parameters discussed to show that RCRA regulated elements, such as, chromium, lead, cadmium, etc. report to the consolidated phase making the salt recyclable. Salt Scrub Reduction Process for the recovery of radioactive and RCRA metals from the waste salts has been developed. The process uses a Ca-Ga intermetallic alloy which recovers over 98 percent of the reactive metals. The matrix salt phase in this process, viz. calcium or alkali metal chlorides, are clean after salt scrub reduction.

Jan 1, 1995

By J. A. Botín

Mining investment decisions are difficult since decision analysis is often based on scarce information. The sources of uncertainty in large mining investment projects are particularly numerous and are present in all evaluation stages. Hence the feasibility decision for projects of this nature will largely depend on how well these sources of uncertainty are managed to achieve bankable risk levels. The risk associated to the construction stages of a mining project is particularly difficult to quantify, mainly because the large number of variables affecting constructive yields, and the complex interactions among constructive resources. This investigation focuses on developing quantitative simulation models and tools to increase the value of a mining project by means of an optimization of the preproduction equipment fleet. The models were validated through their application in the Chuquicamata Underground Mining Project.

Feb 23, 2014

By Robert A. Hains, William P. Balaz, K. Payne

Ceramics are usually used to line chutes, pipes, dust collectors, separators, cyclones or bins where abrasive or corrosive material is moving. Improvements in ceramic manufacturing methods and quality, use of other abrasion resistant materials in combination with Alumina ceramic, improved adhesives and installation methods allow the use of Alumina ceramic tile in applications with impact. This paper discusses the criteria to determine if ceramics can provide a cost effective alternative to other liners for abrasive material handling applications, design parameters for liner systems, system costs, and case histories. The goal will be to provide a practical guide for improving the performance of existing ceramic lined systems or determining if ceramics is a cost effective solution for your abrasive material handling applications.

Jan 1, 1996

By E. Watkins, V. Gangrade

Large-opening stone mines often rely on natural ventilation and a network of auxiliary fans to produce adequate ventilation conditions in the mine instead of main mine fans, which are commonly utilized in coal mines. Large air volumes in underground stone mines, poor ventilation practices, and low operating budgets for mine ventilation potentially increase mine workers’ risk for dust, silica, and diesel particulate matter (DPM) emissions exposure. To help improve mine ventilation practices, the optimal auxiliary fan location for maximum airflow production from a ventilated intersection was determined using a combination of field measurements and computational fluid dynamics (CFD) modeling. In this study, conducted by researchers at the National Institute for Occupational Safety and Health (NIOSH), airflow quantity and fan data were collected at a partner mine to be applied as CFD model input parameters and comparison data for model validation. A six-foot diameter auxiliary propeller fan was introduced into the validated CFD model at three locations at a mine entry intersection with established ventilation flow perpendicular to the fan direction. Placing the fan on the opposite side of the intersection from the target active face area produced the highest ventilation flow rates at the downstream locations tested and produced the lowest amount of air re-circulation. The findings show that optimizing the placement of an auxiliary fan may increase the net effective ventilation flow rate by 70,000 cfm and reduce recirculation by 26%, which maximizes the potential effectiveness of large-opening stone mine ventilation systems and decreases mine worker exposures to airborne contaminants.

Mar 2, 2022

By B. Moudgil, M. Bogan

A mathematical model, based on first-order kinetics, is derived to describe batch settling data. The model is used to predict the settling behavior of solid suspensions under different conditions. The potential benefits of this model to solid-liquid separation processes are discussed.

Jan 1, 1994

By Zhongxue Li, Wenguang Li, Yiqing Zhao, Shuaiqi Wang

"Faced with the serious managerial situations and diverse conditions and needs for mine safety, occupational health and environmental stewardship in Chinese mining communities, an evidence-based approach is proposed for the management of mine safety, health and environment integrity. By the proposed approach, tangible and effective scientific evidence should be collected and accumulated, and the authenticity, accuracy and applicability of the evidence should be assessed to form an evidence-based approach for characterizing mine safety, health and environmental hazards and risks from multidimensional perspectives. The results are then used to formulate diverse safety, health and environment functional requirements. In an evidence-based approach, the evidence is combined with the professional experiences and the actual economic and technological situations, availability and affordability of a mine. This approach is helpful to establish scientific, reasonable, acceptable and effective solutions for identifying and mitigating hazards and improving the level of mine safety, health and environment integrity of mining operations.Introduction / Background In recent years, economic reforms have opened China's economy so that Chinese society has rapidly modernized. Along with this advancement, the exploitation and utilization of mineral resources continues to be active and the scale of mining production continues to increase, which has created a deterioration in resource reserves and as well as the general condition of mining technology. There are many hazards and safety problems in mine production and occupational health as well as in the community environment in China’s mining industry. These problems threaten the security of China's mines and present serious obstacles and challenges to the industry and the government. According to the statistics from the State Administration of Work Safety Supervision, there were 50,500 mine safety incidents in China between 2001 and 2013, which consisted of 31,439 coal mine safety accidents and 19,061 non-coal mine safety accidents, resulting in 30 deaths (Qin 2014). At the same time, mineral dust and radioactive material from mine production processes have increased the morbidity rate of silicosis and cancer in mining workers."

Jan 1, 2017