Search Documents

By Lijun Xu, Ragula Bhaskar

The transport of dust particles from a turbulent air stream on to the surface of a mine entry is mainly due to the effect of diffusion, sedimentation and inertial impaction. While the literature in aerosol science contains many references on particle deposition, most studies apply to smooth surfaces in small, short tubes. The deposition data from those experiments may not be applicable to deposition in mine airways that have large areas of rough surfaces and extend several thousand meters. This paper describes the mechanisms of mine dust transportation and deposition, specifically, by estimating the turbulent deposition velocity for coal dust in mine airways. Data from in-mine experiments on ambient dust concentration and dust deposition along a straight entry were used. A statistical model for dimensionless turbulent deposition velocity was developed, and compared with the models developed by other researchers. The model shows that the distance from the dust source is an important factor in the turbulent deposition of mine dust.

Jan 1, 1995

By Ian S. Lowndes, Adrian T. J. Moll

With the current trends towards the concentration of extraction to fewer but higher production units in deeper seams, often of higher coal rank, the role of methane drainage ranges has become critical. As mines exploit seams at greater depth and more remote locations there has been a need to extend the lengths of methane drainage ranges and to increase the capacity of the surface pumps. This trend has highlighted the need to effectively simulate the operation of a methane drainage range in order to produce the optimum design and operation of a safe and economic system. This paper describes the development of such an analytical tool. The application of this computer model is illustrated by the analysis of the operation of the drainage system of an extensive mine. The paper concludes by considering the development of a [Knowlege Based or Decision Support System] which will assist the ventilation engineer in assessing the current performance of an existing drainage range and will suggest possible remedial modifications or design strategies which may improve the system performance. INTRODUCTION In order to maintain the general body methane levels to below predetermined statutory threshold limit values (TLV's) on major longwall production units there are, for a given production rate, two major complementary control devices which may be employed by the ventilation engineer. These are the combined design and application of a competent mine ventilation and methane drainage system. The methane drainage system should be designed so as to maximise the capture of the methane (firedamp) from the seam being mined and the strata gas liberated in the vicinity of the extraction zone from gas bearing seams or other reservoirs of gas situated at above or below the mining horizon. The design fresh air quantity entering the face should ensure that under normal operating conditions the methane entering in the vicinity of the face is rapidly dispersed and dilute to well below statutory TLV's. The drainage system must therefore be designed to maximise the capture of the methane gas liberated to minimise the amount of gas which enters the ventilation airstream. GAS DRAINAGE The inherent dangers of methane emissions in mine workings have been a problem of concern to mining engineers for many years. To alleviate the risk, methane drainage has been employed for some years to capture the gas before it becomes a hazard to the operation of the mine. The method of drainage employed will be dependent on a number of factors which include the longwall mining method and production cycle employed, the characteristics of the coal seam being extracted and those of the adjacent gas bearing strata. The location of the gas bearing potential of the over and underlying coal measures must be determined. The gas bearing

Jan 1, 1993

By C. Opoku-Ware, M. Kukay, P. Conrad

"This project is exploring the potential for developing trees tolerable to degraded un-reclaimed mine site soils and tailings as a solution to re-establishing long-term tree growth on those sites. The project incorporates growing tree seedlings in an underground greenhouse grown from seeds planted in the degraded mine soils in which they will eventually be planted. The outcome of the project is expected to lead to a successful solution for re-establishing tree growth in soils and tailings containing high metal concentrations with minimal post-planting human intervention. The research is being conducted in an underground greenhouse located 100 feet below the surface in the old Orphan Boy Mine Underground Mine Education Center (UMEC) located on Montana Tech’s campus in Butte, Montana. INTRODUCTION In an effort to improve Butte Area One natural resources, the research project was proposed to help restore tree growth in the Butte Priority Soils Operable Unit Boundary (BPSOU). Research by Blicker, et al. (2003) found that, the BPSOU, which is part of the Silver Bow Creek/Butte Area National Priorities List (Superfund) Site within and near Butte, Montana has multiple historic mining sites situated entirely within the urban setting of Butte. Mine wastes and mill tailings, accumulated from over 100 years of gold, silver, and especially copper mining are dispersed throughout Butte, posing health risks to human and environmental receptors. Stabilization of tailings sites is needed to control fugitive dust, prevent run-off of toxic material resulting in subsequent sediment deposition in streams, reducing the volume of water seepage through acidic and heavy metal contaminated material, and improving land productivity and aesthetic VALUES ((Watkin and Watkin, 1982). If successful, the project will help restore water quality and maintain stream flow in Silver Bow Creek where it flows through Butte Area One. Trees native to Butte are being grown in an underground greenhouse located in the UMEC and will be planted in five areas located within the BPSOU designated for tree planting by the Butte Silver Bow government. Growing trees is expected to help restore vegetative ground cover within the watershed contributing to stream flow in Silver Bow Creek. They will prevent soil and tailings from eroding and being deposited in Silver Bow Creek where they could degrade water quality and choke stream flow."

Jan 1, 2018

By Harry Deitzer

Within the industrial marketplace barium sulfate has an established role as a filler or extender pigment for use in a wide array of applications. The focus of this paper is to outline a number of these applications and in each one characterizes those features of barium sulfate which provide value. Following this is a discussion of the process techniques which have been used to develop value from a selected class of barite ores found in southern Missouri. It is appropriate to define some terms which may help in clarifying some concepts as presented. Use of the term barium sulfate refers broadly to the chemical compound BaSO4 Barite will generally refer to the naturally occurring barium sulfate ores and their properties. Barytes, whether bleached or not, will refer to barite ore made suitable for industrial applications.

Jan 1, 1993

By M. K. Larson, J. K. Whyatt

Proper employment of numerical stress analysis design tools is based on the demonstrated ability of a model to capture key elements of the geologic site model and accurately simulate how these elements interact with a mine design. While these tools have progressed markedly, they are, at heart, a gross simplification of the abundant complexity of a natural setting and its response to mining. A generic deep longwall site model was developed that includes aspects of the geology of deep coal mines in the Wasatch Plateau and Book Cliffs coal fields of Utah. The site model contains a set of common features and observations of how these features typically respond to mining. This site model was the basis for evaluating use of empirical, boundary element and volume element stress analysis tools to analyze the distribution of stress around a deep longwall panel. More specifically, this evaluation examined shifting of stress to panel abutments and gob, distribution of stress in the abutment and deformation and failure of bridging strata. Measurements of abutment stress changes at two sites in the Wasatch Plateau region were used to illustrate model calibration. Overall, these comparisons highlight the considerable differences between methods. Volume element tools can incorporate considerable detail and have fewer underlying assumptions, but this detail carries a considerable computational cost. Boundary element tools are much more efficient. However, this efficiency comes at the cost of added assumptions. These assumptions were challenged by the presence of a strong sandstone unit in the overburden, leading to boundary element results that depart significantly from volume element results. Empirical rules are the simplest, but are even more burdened by assumptions, many of which are implicit in underlying cases. Insight into the nature and impact of underlying assumptions in each method is essential to the proper use of results in mine design.

Jan 1, 2009

By E. J. Meets, C. F. Meyer

Bord and pillar mining at shallow depth (400 m approx. maximum) is widely used in South African coal mines. One of the problems encountered in extracting coal in this manner is the ventilation of advancing bord and pillar headings. The traditional ventilation methods of force, exhaust and overlap (force/exhaust) are reasonably effective but tend to be both cost and labour intensive. Ducting often restricts the available free area of roadways thus impeding the transport of coal and other materials inbye the coal production section. Due to the above facts, ductless fans are currently being used to minimize the amount of ducting required in advancing sections. Two different types of fans are used, namely, vortex fans and the so-called `jet' fans. Vortex fans were developed from the fan blade design used for vertical take-off aircraft. The fans have the capability of delivering air over distances of about 30 m in the underground situation without any ducting attached to it. Jet fans are standard axial flow fans fitted with outlet reduction pieces which increase the velocity pressure at the discharge to such an extent that the air delivery distance is improved to almost match that of vortex fans. The paper describes some applications of both these fan types in advancing bord and pillar sections.

Jan 1, 1993

By Deepak Malhotra

Following a severe recession in the early 1980's, mining companies have taken significant steps to improve metallurgy and reduce operating costs. They do not view chemical reagents and the long-term relationship with reagent producers the same way they did two decades ago. This paper discusses the general perspective of changes that have taken place over the years, especially with respect to cost of production, selling price and environmental constraints. A cooperative program between the consumers and producers of chemical reagents is recommended to understand each other's problems and identify the present and future needs of the mining industry. This approach will be beneficial to the long-term survival of both parties.

Jan 1, 1994

Anhydrite-based dam constructions, which have been implemented successfully in other geological formations, were investigated with regard to their suitability in salt mines. The laboratory investigations show that anhydrite-based building materials with suitable additives bind safely in spite of the high temperatures in salt mines which normally pre-vent hydration. The dependence of the compressive strength, swelling behavior, porosity and permeability upon the choice and ratio of binding material components and additives was determined. Based on the results of these investigations, a pilot-scale experiment was carried out at the GSF Research Mine Asse (Germany) using a mixture suitable for the prevailing conditions

Jan 1, 2004

By F. Breu, R. Fraser, R. Lawrie

Diesel-powered underground mining equipment is generally accepted as the most productive, safest, and most efficient equipment used in underground mining operations. Widespread application of this equipment to underground mining is restricted, however, largely because of the difficulty of controlling the diesel engine exhaust emissions. This paper briefly examines control devices currently available for underground application, and also discusses the theory and mechanics of controlling diesel emissions with particulate traps and filters.

Jan 1, 1988

By Fred W. Stuart

Microprocessor technology has revolutionized the business community by placing tremendous computing power in the hands of the end-user for a very inexpensive price tag. The range of applications covers process control, to office automation, to personal computing capabilities. With the influx of this new technology, which these systems have to offer, also comes some unique operational and control considerations. But before we address these items, let us lay a foundation of common terms to be used throughout this presentation. Due to the rapid advances in microprocessor technology, where a new generation of computers is announced every two or three years, it becomes difficult to define a microprocessor system and have it valid for an extended period of time! Therefore, for this presentation, we will be dealing with a subset of microprocessors called Personal Computers or PC's. At the heart of a PC is a Central Processing Unit or CPU. The CPU performs the actual program and command execution. The programs dealing with driving the various peripheral equipment is referred to as the Operating System (for example: DOS : Disk Operating System, CP/M - Control Program/Microcomputers, etc.). The CPU is normally housed in an enclosure which contains power regulators, peripheral equipment interfacing 'cards', and expansion 'slots' to enlarge the capabilities of the PC system.

Jan 1, 1989

By G. Meschke

"This paper reports on computational and experimental research, performed at the Collaborative Research Center “Interaction Models for Mechanized Tunneling” at Ruhr-University Bochum, Germany. Research covers a broad spectrum of topics relevant for mechanized tunneling in soft soil conditions. This includes advances exploration methods and models for the characterization of the in-situ ground conditions, the interaction of the face support and the tail gap grouting with the porous soil, multi-scale models for the design of fiber reinforced segmental linings with enhanced robustness, computational methods for the numerical simulation of the tunnel advancement, the soil excavation and the material transport in the pressure chamber, logistics processes and risk analysis in urban tunneling.INTRODUCTIONMechanized Tunneling has proven itself as an economical and flexible construction method that continues to undergo a dynamic evolution process. Shield diameters continue to increase, and the application range of tunnel boring machines is being extended to an ever-increasing variety of geotechnical conditions. In order to maintain economic viability and to ensure an environmentally friendly construction process, realistic and reliable numerical models are required in order to make informed decisions during planning and construction. To provide a reliable numerical prognosis, it is necessary to accurately assess and understand the interactions between the components involved in mechanized tunneling with the surrounding site, the ground, and any pre-existing structures. Heterogeneous geological conditions and often only approximated ground parameters create, in contrast to other engineering projects, special demands. This necessitates new insights to new problems that can only be effectively solved through truly interdisciplinary research. To address these challenges, the German Research Foundation (DFG) has established the Collaborative Research Center “Interaction Models for Mechanized Tunneling” (SFB 837) at the Ruhr-University in Bochum in 2010. Collaborative Research Centers are interdisciplinary scientific research groups in which cooperative research is conducted under the umbrella of a central research theme. With a research budget of ca. 10 Million Euros for the second 4-year funding period, and a research team composed of 13 project leaders along with approximately 35 scientific assistants the SFB 837 is currently one of the largest research groups conducting fundamental research in tunneling related topics worldwide.RESEARCH TOPICSThe research topics of the SFB 837 encompass a number of relevant planning and construction related aspects in mechanized tunneling (Figure 1). These research themes are each supported by computational models and laboratory investigations and are all included in an SFB overarching Tunnel Information Model (TIM). Interaction groups integrate and combine the results of different submodels through prototypical cause-and-effect relationships, and through the analysis of the Wehrhahn metro line (WHL) project in Düsseldorf, which has been adopted as the reference project for the SFB 837."

Jan 1, 2016

By Todd R. Taubert, Kenneth L. Bickel

The U.S. Bureau of Mines (USBM) pioneered the development of disposable filters for reducing diesel particulate emissions from permissible mining machines. The USBM is now evaluating filter media that can withstand the high exhaust temperatures on nonpermissible machines. The goal of the evaluation is to find an inexpensive medium that can be cleaned or disposed of after use, and will reduce particulate emissions by 50 % or more. This report summarizes the results from screening tests of a lava rock and woven fiberglass filter media. The lava rock media exhibited low collection efficiencies, but with very low increases in exhaust back pressure. Preliminary results indicate a collection efficiency exceeding 80 % for the woven fiber media. Testing of both media is continuing.

Jan 1, 1995

By David Jenkins

Grefco Inc. operates two diatomite mines in the western Santa Ynez Mountains. The larger of the two mines, the Palos Colorados Mine, is located approximately seven miles southeast of Lompoc. The Miguelito Mine is located about two miles south of Lompoc on the west side of the Miguelito Canyon. Diatomite from the Palos Colorados and Miguelito mines is trucked to the Grefco plant at Lompoc for processing (Figure 1). HISTORY Grefco, Inc. evolved from the originating Dicalite Company which in 1929 began operations at the Walteria plant in the Palos Verdes Hills south of Los Angeles. In 1942 Dicalite leased the Palos Colorados mine at Lompoc. In 1944 the Dicalite Company was purchased by Great Lakes Carbon Corporation.

Jan 1, 1995

By R. Brough, T. K. Moller

There are differences in design aspects between steel and rubber linings in grinding mills. This paper describes the basic design rules for rubber liners for different grinding applications. When converting a mill from steel to rubber liners, the design must be changed from such familiar steel liner shapes as wedge bars and plates, wave liners, and ship-lap, to take advantage of the characteristics of rubber. Very little of the knowledge of the wear properties of steel can be used for the design of rubber mill liners.

Jan 1, 1990

By V. E. Housman

EPA's Mining Waste Section within the Office of Solid Waste is continuing to collect and analyze information on mining waste management practices. Starting in 1991, the Mining Waste Section has continued to conduct site visits and prepare case study reports on the waste generation and management practices of operating mines. In choosing sites to study, a reasonable attempt was made to provide diversity in mining commodity types, geographic regions, geology, climate, and environment. To date, EPA has visited the following mines: Asarco Troy (copper) in Montana, Newmont Rain in Nevada (gold), Cyprus Thompson Creek (molybdenum) in Idaho, LTV Steel (iron) in Minnesota, Phelps Dodge Morenci (copper) in Arizona, Doe Run Fletcher (lead) in Missouri, Brewer (gold) in South Carolina, IMC Four Corners (phosphate) .in Florida, Pennzoil Culberson (sulfur) in Texas, Nerco Cripple Creek (gold) in Colorado, Copper Range White Pine (copper) in Michigan, Magma San Manuel (copper) in Arizona, Colosseum (gold) in California, and several gold placer mines in Alaska, including the Valdez Creek Mine. EPA has prepared a case study report on each facility. The mine operators were provided an opportunity to comment on their respective site visit report and their comments have been included in' each respective report. These site visit reports have in turn been incorporated into technical resource documents which provide a detailed description of each mining sector. EPA is currently reviewing the technical resource documents and plans to release the documents in the Spring of 1994.

Jan 1, 1994

By Jeffrey D. Swanson, Martin L. Smith

Smelterville Flats in Idaho's Silver Valley has been designated as a Superfund site due to metals contamination resulting from the use of the South Fork of the Coeur d'Alene river as a tailings impoundment earlier in this century. Tailings average in excess of 4% lead and zinc. Selective mining of highly contaminated zones is being studied as one of several possible remediation strategies. The first step towards remediation is the examination of the stratigraphic, geochemical and spatial characteristics of the site. These characteristics are related to appropriate sampling protocols and exploratory sample grid design. Special problems involved in the geostatistical analysis of tailings are emphasized.

Jan 1, 1992

By O. J. R. Baena, I. C. Sánchez, J. L. G. Guzmán

Frontino, a municipality in western Antioquia, Colombia, has more than 200 years of mining tradition. Currently, mining activities are carried out for lode gold using subway tunnels, where the grinding of the material is done in "cocos", whose energy depends on internal combustion engines and ACPM, environmentally polluting and inefficient methods. In accordance with the Sustainable Development Goals as an initiative developed by the UN, different mining methodologies that are aligned with these are constantly being analyzed. This study proposes to eliminate the use of hydrocarbons in artisanal mining, mainly promoting Sustainable Development Goals 7, 9, 11, 12, and 13. This will be achieved through an energy transition to renewable energy sources that take advantage of the topography and water resources of the area, providing advantages to the communities that live there, such as lighting, electricity for cooking, ventilation for mines, etc

Mar 2, 2022

By D. O. Shah, K. C. Adiga

Flotation of coal after multistage addition of frother was found to yield coal fractions with significantly lower ash content as compared to the feed. Ignition and combustion characteristics of different coal fractions were evaluated using a differential thermal analyzer (DTA). A correlation between low ash content, low specific gravity, and high reactivity of coal was observed. It is suggested that in the ignition stage, removal of mineral matter enhances reactivity through the physical changes brought about by ash removal. A detailed analysis of pre-ignition kinetics indicated the possible effect of bulk density of coal in terms of resistance to volatile release and effective (available) surface area of coal. In the char combustion stage, mineral matter seems to influence reactivity through catalytic activity of surface concentrations of metal ions, ratio of combustible/non- combustible material, internal pore structure, and surface roughness.

Jan 1, 1988

By Tamara Nestorovic, Luan T. Nguyen

"With the aim to mitigate excavation risks and reduce the costs caused by tunnel boring machine (TBM) stoppage when tunneling under uncertain soil conditions, prediction ahead of the tunnel face has become an increasing interest in the tunneling community. Our research topic is concerned with developing effective concepts for nondestructive identification of geological anomalies ahead of the tunnel face by waveform inversion of reflected tunnel seismic waves. The authors demonstrate that this new technique is promising in providing tunnel engineers with an accurate image of the geological situation that the TBM is going to encounter thanks to the waveforms’ rich information about the geological structure that affects propagation, reflection/refraction and mode conversion behavior of the elastic waves. By setting up a 2-dimensional numerical model for simulation of tunnel seismic wave propagation influenced by a dip layer change ahead of the tunnel face, the authors show that the waveform misfit to be minimized by the inversion process is highly multimodal and therefore propose a hybrid stochastic optimization method that can quickly and robustly converge to the global minimum. DEVELOPMENTS IN TUNNEL ADVANCE EXPLORATION Conventional site investigation by drilling boreholes helps to draw a general image of geological structures along the borehole axes but that image is likely to misrepresent the detailed geological structure due to limited sampled locations. Due to high costs and restricted boring space which deep tunneling and tunneling under urban areas encounter, many industrial and academic research groups have had great interest in developing nondestructive ahead of the tunnel face prediction systems. That means only excitation sources and receiving sensors, which are usually placed on the ground surface or on the side walls or on the cutter head of the TBM, are used for acquisition of the measurement data. The recorded signals in the form of seismic or electromagnetic/ electrical waves, which travel through the geological structure or are reflected back from it, hold the signature of the geological structure of concern, such as geological layer changes, fault zones, erratic rocks, boulders, construction remnants, etc., and therefore can be used to reconstruct the spatial and material properties of those hidden geological structures. Most common nondestructive ahead-of-tunnel investigation systems to date are based on interpretation of reflected elastic/ acoustic waves (seismic waves) and analysis of electromagnetic/ electrical resistivity signals (Mooney et al. 2012). However, due to insufficient penetration depth and spread of signals generated by radar and geoelectric sources, the use of seismic waves for ahead of the tunnel face prediction (tunnel reconnaissance) is more preferable (Kneib et al. 2000; Bohlen et al. 2007)."

Jan 1, 2016

By H. L. Ehrlich

Processes involving biological solubilization of metal values from ores, or removal of mineral constituents that interfere with metal value recovery from ores by abiological means, published mostly in the last 10 years, are reviewed. Many of them, though promising, have yet to be tested on a pilot scale or applied industrially.

Jan 1, 1987