Search Documents

By R. P. King

Thermal pretreatment can significantly improve industrial comminution operations by reducing energy requirements and increasing mineral liberation. The effect of pretreatment using conventional and dielectric heating followed by quenching on the fracture characteristics of a number of single and multiphase brittle materials has been investigated using the Ultrafast Load Cell. It has been observed that very significant reductions in both fracture energies and the material integrity (damage) were achieved by heating followed by water quenching.

Jan 1, 1995

By D. M. Bodily, R. Jin, W. Hu

Four methods to assess the relative floatability of fine coal have been tested: flotation with frother only, salt flotation, timed-release analysis, and flotation with frother and collector. A practical and simple criterion that combines the separation efficiency (capacity factor) and kinetic rate constant (intensity factor) has been suggested. Five coal Samples from Utah were tested. Based on test results, it was concluded that the floatability test with collector and frother is closer to practice, and according to the suggested floatability criterion, coal fines can be classified into four categories of relative floatability: very easy, easy, moderate, and difficult.

Jan 1, 1988

By Alena Conrads, Markus König, Markus Scheffer, Markus Thewes, Hannah Mattern

"INTRODUCTION In recent years, the development of tunnel boring machines has revolutionized the tunneling industry. The general structure of a tunnel boring machine (TBM) can be described as a multi-component system. To achieve high performance rates, machine elements have to perform reliably. Performance losses and interruptions of the construction process should be prevented or at least, reduced to a minimum. In order to achieve high advancing rates, cutting tools must be in good condition at any time. Furthermore, failure of individual tools might result in increased and faster wear of remaining structural components. For this reason, maintaining and replacing cutting tools is crucial to prevent project delays due to insufficient boring performance. Precise prognoses concerning the prevailing geology are infeasible and thus, efficient scheduling of maintenance actions is challenging. The intention of this work is to analyze different approaches of TBM maintenance in soft ground. Different strategies are analyzed by the use of a simulation approach. Cutting tool condition is regarded as performance limiting factor. The maximum operation time of the cutting tools is determined using the “Soil Abrasivity Index”. A case study serves to show the effects of different maintenance strategies on total project duration. SCHEDULING OF MAINTENANCE ACTIONS Scheduling maintenance actions of single and multi-component systems concerns numerous fields of industrial production. Concentrating on mechanized tunneling in soft ground, cutting tool maintenance represents the most common reason for intermission of advance (Köppl 2014). In literature, time-based and condition-based maintaining techniques are widely discussed. The following section outlines the principles of time- and condition-based policies. Furthermore, examples for their applications in recent research are given. Time-Based Maintenance In general, the time-based maintenance approach assumes that the failure behavior of the system components is predictable. Maintenance actions are scheduled according to predefined intervals (e.g., hours, days, weeks). A detailed analysis of preventive repair times or interval forms the basis for maintenance decisions. For this approach, an adequate quantity and quality of data is fundamental. Numerous studies deal with the analysis of time-based maintenance for production equipment. In fields of mechanized tunneling, unplanned machine downtimes restrict the applicability of time-based maintenance approaches. Thus, this paper mainly focuses on condition-based maintenance."

Jan 1, 2016

By Lynn B. Hales, Randy A. Yncbausti, Rick Smith

Object oriented programming has been developed to model the way we think about the world. It allows higher levels of abstraction, generalization and classification than many other programming techniques. Some tools of object oriented design and programming are encapsulation, classes, inheritance, modularity and reusability. Expert systems have been used for years to implement process control strategies in the minerals industry. Expert systems allow process control knowledge to be expressed in linguistic rules that are processed by an inference engine. Expert systems which employ object oriented design and programming provide new opportunities for real- time process control. The concepts of object oriented programming and an example object oriented expert system are discussed in this paper.

Jan 1, 1992

By Thomas F. Pedersen, J. Jay McNee, Alan J. Martin

Field sampling was conducted in Lake Junin, Peru in order to assess the post-depositional reactivity of the highly contaminated lake sediments. High resolution profiles of dissolved Fe, Mn, SO42- and H2S across the sediment-water interface illustrate that the organic-rich sediments in the main basin become anoxic within several millimetres of the sediment-water interface. These permanently submerged deposits in the main basin serve as a diffusive sink for dissolved Zn and Cu. Conversely, the periodically unsaturated deposits in shallow areas are characterized by the remobilization of Zn and Cu in the deep acidic (pH < 4) pore waters, resulting in the release of these metals to the overlying water column.

Jan 1, 2000

By C. Klauber, H. G. Linge, W. G. Jones

The carbon-in-pulp process for gold processing depends on the adsorption of dissolved Au(CN)2- from solution onto activated carbon. Our work shows that coconut and peat based carbons have the same mechanism and kinetics of adsorption. There is no contribution to the bonding from carbon-oxygen functionalities on the carbon surface, as has been invariably supposed in all previous theories for the mechanism of the reaction. It is shown that Au(CN)2- is reversibly adsorbed intact on, and parallel to, the graphitic planes of the carbon. The physiochemical basis of the measurement of carbon reactivity for gold adsorption is discussed.

Jan 1, 1989

By J. A. Muñoz, A. Ballester, C. Gómez, M. E. Sevillano, M. Figueroa

The electrochemical behavior of massive chalcopyrite (CuFeS2) electrodes has been studied in the absence and-in the presence of mesophilic microorganisms, using cyclic voltametry as analytical technique. The culture was principally formed for Thiobacillus ferrooxidans, Thiobacillus thiooxidans and Leptospirillum ferrooxidans. The results showed that the reactivity of the chalcopyrite gradually increased with the bacterial treatment. The anodic dissolution process of the chalcopyrite treated with microorganisms was related to the breaking of passive layers when the applied potential increased. The analysis of the surface products showed that the chalcopyrite was covered with a superficial film avoided its dissolution during the bioleaching test. So, the rest potential of the bioleached samples increased possibly as consequence of its superficial transformation.

Jan 1, 1995

By D. C. White

The Vulture Mine near Wickenburg, Arizona was a major gold producer from 1863 to 1942, having yielded about 11,000 kg Au and 8,000 kg Ag. Gold occurs as coarse native metal and electrum in quartz veins and also finely disseminated within a quartz monzonite sill and its silicified wall rock. The sill is semi-conformable within a Proterozoic volcaniclastic-dominated sequence all dipping north about 35°. Early mining focused on the vein-hosted gold particularly in the immediate hanging wall and footwall of the sill. Later efforts included some open-pitting of the outcropping sill and adjacent altered and mineralized rock. Two sets of post-mineral faults have complicated the orebody geometry.

Jan 1, 1988

By M. M. Botz

Cyanidation tailings disposed of in a surface impoundment experience a loss of cyanide due to natural attenuation, which frequently reduces the cyanide concentration to very low levels. Quantifying cyanide losses in terms of impoundment geometry, local weather conditions and feed-solution chemistry has been largely empirical in spite of the fact that, in many cases, mining operations rely on surface impoundments to reduce cyanide to below an internally regulated concentration or below an effluent limitation. To permit a quantitative evaluation of cyanide losses in an impoundment, a computer simulation was developed to estimate the losses of free, weak acid dissociable (WAD) and total cyanide due to dissociation, photolysis and volatilization. Results of the model are compared with data collected for a North American tailings impoundment in 1998.

Jan 1, 2000

By O. Akinkugbe

The safe, productive exploitation of coal in multiple-seam situations requires specific design technology. At present, there are two general design approaches that the mining engineer can use to analyze the multiple-seam problem in question, either simple empirical relationships or complex numerical models. Often, the empirical approaches are too general for the specific problem and the numerical models require too much time and expertise for the practicing engineer. In this paper, a new program designed for quickly and easily calculating the stresses, strains, and safety factors associated with basic multiple-seam mining situations is presented. The program implements a simplified, two-dimensional boundary-element method in order to model the complex multiple-seam stress and displacement interactions. The program incorporates automatic coal and gob property generation to simplify the input, and inherently calculates pillar safety factors to enhance the output.

Jan 1, 2004

By C. J. Konya

When blasts are designed, the assumption is made that all blastholes release near ideal energy. In many types of mining operations, some blastholes release very little useful energy. These blastholes will be called malfunctioning blastholes. Recent studies indicate that on many types of blasting applications, 30 percent of blastholes are malfunctioning. This malfunctioning routinely occurs on the operation and is not an unusual occurrence. This paper will discuss the cause of malfunctioning blastholes and methods to minimize the detrimental effect on both safety and costs.

Jan 1, 1988

By David M. Miller, Pramod C. Thakur, Larry D. Taylor

The most common technique used to suppress respirable coal dust in air is that of spraying with fine water particles. The water droplets are typically much larger than respirable dust particles and they collect dust particles mainly by interception. Dust collection efficiencies can be improved by reducing the droplet size and in- creasing the droplet velocity. This is typically done by reducing the surface tension of water and increasing the water pressure. Dust collection efficiency can be further improved by in- creasing the electrical attraction between the water and dust particles through electrostatic charging. A technique developed by Conoco accomplishes both surface tension reduction and electrostatic charging by discharging weak solutions of surfactants in water at high pressures, 13.8 to 27.6 MPa (2000 to 4000 psi) in an intrinsically safe manner. The paper de- scribes the process and presents related dust suppression data.

Jan 1, 1986

By Gustavo A. Aristizábal-H, Oscar J. Restrepo-B, J. Alejandro Delgado-J

"In Antioquia region of Colombia – South America most of extractive activity is developed as artisanal and small-scale level, exploiting different types of minerals resources but predominantly gold. This is not only an ancestral livelihood of hundreds of families in this region, but also their unique way of subsistence. However, that situation has not had a positive effect in the sustainable development of this territory because of several unsustainability factors mainly related to mercury use for gold extraction, the incorrect management of tailings and the informal way in which miners perform their activity. In 2010 Antioquia was the place with the highest contamination by mercury in the world with serious effects in ecosystems and health of habitants of this region (Veiga 2010) This paper presents a Socio-Technical Model focused on strengthening capabilities and social capital of artisanal and small-scale miners and its surrounding communities in Antioquia region. This is based on processes of evaluation, design and implementation of appropriate technologies to obtain “clean minerals” without using mercury and with a right management of tailings. In gold extraction it is about gravitational methods of concentration, which take advantage of high density of this element. These methods not only are cleaner but more profitable for miners. Notwithstanding its technical origins, the current model proposes a holistic framework that manages the elimination of mercury in mining not only as a technology transfer matter. Thus, more than formalization the strengthening process seeks to promote a business vision in miners and to develop productive chains in surrounding communities, this means to improve the skills of artisanal and small-scale miners to organize in a corporative way and to help surrounding communities to provide support and supply services to mining and even to other companies. Besides, the articulation with local institutions drives to reinforce their functions of control and accompaniment. In shorthand, this effort aims to empower local institutions, miners and surrounding communities in such a way they are able to face together their own development challenges in a sustainable way."

Jan 1, 2017

By W. E. L. Minter

The most important Witwatersrand gold placers occur on extensive unconformity paleosulfaces that were produced during protracted periods of fluvial degradation. The erosional etches on what was generally unlithified sub-strate indicate that low sinuosity erosion patterns prevailed. The transport systems were dominantly braided fluvial with a minor debris-flow component. The placer sediments were non-cohesive sands and gravels. They were evidently transported by fluctuating, yet perennial, discharges across extensive, low relief braid plains, not far from littoral environments. Progress made in understanding heavy mineral transport processes now emphasizes the importance that selective entrainment probably had in producing concentrations. Cognizance that these characteristics are not unique to the Witwatersrand should be taken into account when designing exploration models.

Jan 1, 1991

By J. P. McDonnell, L. A. Beckett, K. Y. Hammy

Dangerously high stress areas can be controlled by proper mine planning and/or destressing. This paper reviews practical methods to detect and destress high-stress zones along coal faces. The US Bureau of Mines investigated stress-related burst problems and destressing efforts at a cooperating mine. Laboratory tests of the drilling yield method for high stress detection were conducted to determine the correlation between the volume of cuttings obtained and the magnitude of the applied stress. A three- dimemiom1 computer modeling program was used to evaluate the effectiveness of stress relief methods.

Jan 1, 1987

By G. R. S. Smith

In any filtration, it is primarily the filter medium (cloth) and cake filtering properties that control the type of filtration equipment used and filtration conditions. The advent of new types of filter cloths, such as the membrane cloth discussed in this paper, can result in significant changes in filtration techniques and areas of application for filtration. For many suspensions, for instance, conventional filtration is uneconomic compared to gravity separation or not filtering at all (as with product recovery from dilute streams) because the solids are very fine, are hard to retain and build up filter pressure rapidly, and once retained are hard to remove. As a result of the developments discussed here, this is no longer the case. This technique and the use of the membrane filter cloth is well established. This filtration is currently being used for white liquor filtration in twenty-four mills worldwide in the chemical recovery step of the kraft process for producing paper pulp where it is replacing gravity thickeners in new plants. Filters up to 1000 sq. ft. (100 sq. meters) are filtering large volumes of solids from hot caustic solutions. The filtration materials and techniques discussed in this paper open the way to new methods and applications for filtration in the mining industry. It is not the intention of this paper to give a vigorous analysis of the different separations, but to outline some of the ways in which this filtration technique might be used in the mining industry.

Jan 1, 1989

By J. B. Hiskey, S. Chander, B. J. Scheiner

The use of selected iron complexing agents in preventing or ameliorating acid mine drainage was investigated. The experiments were conducted in weathering columns using refuse samples from a coal cleaning plant. It was observed that the treatment with iron complexing agents significantly altered the rate of oxidation. Some of the reagents tested reduced the rate of oxidation whereas the others even enhanced it. The results showed that a commercial reagent containing oleyl imidazoline was most effective in retarding the oxidation rate. In addition, a simple treatment with this reagent substantially decreased the rate of oxidation of pyrite in a column that was generating acid at a high rate. The effect of this reagent on the surface properties of pyrite was studied by cyclic voltammetry and zeta potential measurements. The decrease in the rate of oxidation resulted from suppression of both anodic and cathodic reactions at the surface of pyrite.

Jan 1, 1993

By D. L. Stevens

Following an in-depth scenario and strategic planning exercise in 1997, Noranda&apos;s mine production goal was set at 500,000 tonnes per year of both copper and zinc metal within five years. There had been no recent discoveries, reserves were shrinking and things had to be done differently and quickly. Change is now continual in our program but here is what we did first: Combined the exploration and business development groups Formed teams to search for and respond to opportunity Made our geologists more business minded and our engineers more optimistic Went global Set clear thresholds, farmed out the marginal properties, fast tracked the others Focused reconnaissance exploration where we had a clear competitive advantage Became a "flexible" partner to both juniors and seniors Is it working? A number of successes, near successes, and outright failures are discussed. The main result is a much higher rate of opportunity flux which is essential for success in the mining industry.

Jan 1, 1999

By Eric Monrad

Discrete event simulation modeling provides a tool to quantify the throughput capacity of stockyards. Interactions between the main equipment types (trains, dumpers, conveyors, stackers, reclaimers, shiploaders) can be captured, including route blockages, breakdowns, and planned maintenance. Simulation has been successfully used at world-class stockyard facilities to determine current capacity and to identify gains resulting from improvement projects. Recent projects have focused on iron-ore, coal, and soya facilities, but the technology is suitable to be used on any bulk material type.

Jan 1, 2008

By Mario Eduardo Rossi

The Universal Kriging (UK) and the Ordinary Kriging (OK) systems of equations are variations of the well-known system of Normal Equations. They differ only by the number of constraints present in the system. The dual version of these sytems enables one to interpret kriging as the fitting, of an interpolation surface, whose components are a series of variogram functions plus a polynomial trend model. This trend model should account for any systematic decrease or increase of the variable over the study area. It is shown that modeling the trend is useful only when the locations being estimated are beyond the range of influence of neighboring data (extrapolation cases). A case study based on a public-domain coal data set is presented. The variable described (seam thickness) shows an actual trend of increasing data values towards the NW corner of the region considered. UK and OK are used to estimate coal thickness at locations within sample data range (interpolation cases). The UK algorithm that includes a model for the trend does not improve the estimation when compared to the simpler OK algorithm with no trend model. Thus, in interpolation situations, the simpler OK algorithm is recommended.

Jan 1, 1989