Search Documents

By A. E. Ketler

Optical smoke monitoring fills an important gap in ventilation and fire safety: namely monitoring of smoky, low temperature fires where little CO and heat are generated. Smoke monitoring also avoids the nuisance alarms due to diesel exhaust, battery chargers, blasting and welding. The smoke optical density (OD) fire alarm standard specified by MSHA presents an opportunity for improved safety. Experience of actual mine usage of the SmokeBoss*100 is reviewed, with particular regard to effectivity, maintenance and cost.

Jan 1, 1995

By G. J. Joy, J. P. Rider

"Technical advances in longwall mining over the last several years have resulted in much larger and faster shearers that have the capability of mining at speeds over 100 ft./min. This has resulted in a substantial increase in the amount of dust that is generated at the shearer and during shield advances. Meanwhile, increased underground coal production has put a greater demand on longwall dust control systems as some operators have had difficulty maintaining consistent compliance with federal dust standards. To address this need, the National Institute for Occupational Safety and Health [NIOSH] is investigating the effectiveness of a water spray manifold mounted on the tailgate end of the shearer body. The sprays are oriented parallel to the tailgate ranging arm, and these sprays create a water curtain confining the dust plume near the face, preventing the dust from drifting into the walkway. This redirection of dust provides a clean air envelope for the tailgate shearer operator and jacksetters working near the tailgate drum. Three different tailgate spray manifold designs were tested and evaluated at the Office of Mine Safety and Health Research [OMSHR] Pittsburgh Longwall Test Facility. Manifolds were equipped with hollow cone or flat fan water spray nozzles and evaluated at three face air velocities (500, 700, and 900 fpm) and at water pressures of 100, 150, and 200 psi. Reductions in dust concentrations were observed at six face sampling locations for all the tailgate manifold systems at each of the tested spray pressures and face velocities. Based on results from the laboratory tests showing reductions in dust concentrations at sampling locations downwind of the shearer a spray manifold was fabricated and evaluated at an underground operation. INTRODUCTION In 2012, underground coal mining in the United States produced a total of 342 million short tons, with longwall mining accounting for over 53% of this production [EIA 2013]. The longwall mining industry continues to see remarkable and significant improvements in longwall mining equipment and mining practices. Average shift production during compliance dust sampling has increased from 3,500 tons per shift in 1994 to approximately 6,000 tons per shift in 2012. A dramatic decrease in working longwall faces from 80 to 49 has occurred over the same period [Fiscor 2013]. Factors specific to longwall mines that supported productivity improvement include: higher capacity shearers, improved shield hydraulics and control, higher horsepower for equipment, wider face conveyors, and larger faces. Today, the average face width has increased to 1,188 ft., with one longwall operation reporting a face width of 1,650 ft. compared to an average of 750 ft. in 1994 [Fiscor 2009, 2014]. Panel lengths in 2013 averaged 11,307 ft. compared to 7,000 ft. in 1994. Overall production from U.S. longwalls has increased by nearly four percent from 2007 to 2012 with over 182 million tons mined annually [EIA 2013]. Given the volume and rate of coal produced on longwall faces, the potential to generate large quantities of respirable coal mine dust also exists."

Jan 1, 2015

By T. Marcher, C. Mathiesen, M. Allende, S. Bauer

"A unique pumped hydro storage facility using the ocean as a lower reservoir, combined with solar PV to create consistent, clean power will be presented: the Espejo de Tarapacá Project is comprised of a 300 MW seawater pumped storage hydroelectric plant using the Pacific Ocean as its lower reservoir and an existing natural concavity at the desert as its upper reservoir. The plant site is located in Chile’s northern coast 90 km south of Iquique. The site is characterized by a rocky shoreline and about 600 m of flat terrain moving inland, with an abundance of rock outcrops, after which there is a steep 700 m cliff. The power house and all waterways will be underground. The main focus is to present the rocks being expected in the underground works. As one of the actual most tectonically active regions of the world the seismic activity is particularly relevant and will be outlined in the presentation. INTRODUCTION Valhalla Energy is an independent Chilean-owned power development company. It focuses on the development, ownership and operation of renewable power projects. Valhalla was founded in 2011 with the goal of developing Chile’s natural renewable energy resources and strategically diversifies the country’s energy matrix away from an overdependence on imported fossil fuels. Valhalla began developing pumped storage hydro projects to provide scalable, clean, competitive, and reliable electricity by combining Chile’s superior solar resources with the country’s unique and extensive coastline suitable for storage.The capacity for renewable energy supply is driven by two distinct and unique natural characteristics found in northern Chile: (1) the abundant and reliable solar irradiation in the Atacama Desert and (2) a coastal site that benefits from a steep cliff and a natural concavity both within a relatively small land mass (see Figure 1). There are several potential sites in the northern part of the country that can be developed. The “Espejo de Tarapacá Project” is the first one to be built and subject of the present paper."

Jan 1, 2016

By T. Altman

Using theory of network planning together with graph theory, an algorithm is presented that creates canonical diagrams for mine ventilation networks (M VN). The data generated by the algorithm is used in the construction and plotting phases of a program that automatically plots the canonical diagrams, which can then be used for further studies of a given MVN.

Jan 1, 1988

By R. E. Gertsch

Mechanical mining holds great promise for the mining industry. Realizing this promise depends on giving mine operators the capability to evaluate the higher production, the lower costs, and safety enhancement that comes with mechanical mining. The opportunities for low cost and high production must outset the high capital costs associated with mechanical excavation. Giving the mining industry the tools to effectively evaluate and successfully implement mechanical methods defines the challenges and directions of the mechanical mining industry.

Jan 1, 1994

By Patricio Zarate

Due to the intrinsic variability in orebodies, similar metallurgical behaviour of all material sent to the concentrator is expected to have some variability. Still some specific ores have anomalous performance which can severely impact on the concentrator’s production of metal, in this case copper. The study first will show the mineralogical characteristics of “usual ore” and of this specific “abnormal ore” which will have to be processed by the concentrator in the future. After that base conditions on both ores and flotation test procedure will be explained. Later the different alternatives tested regarding collectors and modifiers results will be compared. Finally, after discussing the different results with different reagents and considering operational variables of the concentrator, Floticor PD 702 is recommended to obtain the best copper recovery without increase in excess mass recovery.

Feb 1, 2025

By S. D. Thompson, G. T. Lineberry, A. J. Basu

Conveyor belt haulage has become the preferred mainline transport method in underground coal mining, especially for multi-unit mines. Proper designs for belts (width and speed) and surge bins (placement, capacity, and discharge rate) are necessary to achieve efficient mine haul- age. Two computer simulation models, CMBCS and BELTSIM, available for designing these parameters were compared. These comparisons included modeling, input data requirements, statistical flexibility, accuracy of simulated loading, and execution time.

Jan 1, 1991

By L. Larrimore

Electric utilities depend heavily on coal as a major fuel source for power generation, annually producing more than 85 million ton'> of ash, boiler slag and FGD (flue gas desulfurization -"scrubber") materials as by-products. Utilities and others who burn coal have traditionally disposed of these by-products in ponds or landfills. However, in the last 10-15 years there has been a greatly increased emphasis on beneficial utilization of these materials by the producers themselves as well as by customers who purchase the by-products. Regulatory, cost and technical performance issues currently impact the use of coal ash and other coal combustion by-products (CCB).

Jan 1, 1997

By C. D. Litton

When methods to prevent the occurrence of fire in underground mines fail, the next line of defense is to rapidly and reliably detect the developing fire, so that subsequent evacuation and control procedures can be safely and successfully implemented. To provide this capability requires an understanding of the operational principles of different types of fire sensors, their merits as well as their limitations, and performance characteristics of the monitoring systems that control and process sensor data; an understanding of how fires develop and the different types of fires that can occur, along with their characteristics and the hazards they present; an understanding of the impact of the mine environment and routine mining activities, not only in terms of these effects on fire sensors but also in terms of the impact of mine ventilation and mine geometry on fire growth, fire characteristics and the detection process. All of these factors are components of the technology of fire detection, and when insufficient knowledge of any of these components exists, the ability to implement adequate mine fire detection systems is diminished. Within the last decade, significant advances have been made in fire detection technology applicable to underground mines. These advances include not only the development of improved sensors and better monitoring systems, but also an expanded understanding of how to deploy sensors, set sensor alert/alarm levels, account for ventilation effects, etc. In addition, there has been an increase in our knowledge of the types of fires that occur, the types of combustibles involved, characteristic times for fire growth and development, the levels of heat, smoke and gas that are produced and the hazards that result. It is the intent of this paper to provide not an overview of current mine fire detection technology and, also, to present data obtained for some smoke sensors that have potential for use in underground mines. The paper will also discuss the data, information and resources that are currently available and seek to identify those areas most in need of further research and development.

Jan 1, 2011

By R. Pazhianur

Many investigators conducted surface force measurements between hydrophobic surfaces in water, and observed attractive force that was substantially stronger than the van der Waals attractive force. The excess force was appropriately referred to as “hydrophobic force”, for which many different theories have been put forth by numerous investigators. In an earlier publication (Yoon and Ravishankar, 1996), it was suggested that the hydrophobic force maybe due to the interaction between the large dipoles created by the surfactants adsorbing on solid surfaces in patches (or domains). In the present work, a mathematical model has been developed to further elaborate the theory.

Jan 1, 2003

By R. Larry Davis

Over the past decade there has been a continual decrease in domestic oil reserves accompanied by a sharp increase in the demand for energy. Even with increased imports of foreign oil, the energy demand has not been met. This has forced many users to turn to substitute fuels. Of the many substitute fuels available most users are turning to and creating an increased demand for low sulfur coal. Because of the increased demand for low sulfur coal as well as the inherent problems in producing eastern coal, many producers have turned their attention to the large deposits of low sulfur coal in the western United States. Western coal mining is, however, not without its problems such as high moisture content, high ash content, highly variable sulfur content, multiple seams, and/or pitching seams. It is to aid in the solution of these problems that this chapter is directed.

Jan 1, 1979

By D. Bizier, B. H. Gardner, Y. P. Wang, S. Serata

As part of an ongoing effort to develop more cost-effective and “user friendly” hardware for geomechanical measurements required for underground mine design, Serata Geomechanics, Inc. (SGI) has investigated the potential of borehole pressure cells (WCs) for in situ measurement of stress states and continuous monitoring of changes in ground stress. In particular, because of certain advantages gained thereby, WCs utilizing an elastomer, instead of metal (e.g., copper), for the skin of the pressure cell have been developed. A data analysis technique for determining ground stress state directly from BPC data has been developed. This technique has been tested for salt ground through both in situ applications and computer simulation analysis of the BPC/borehole boundary interaction. This paper discusses the data analysis technique, the results of field and computer simulation testing of its validity, and evaluates the advantages of elastomeric BPCs in relation thereto. It utilizes field data from recent elastomeric BPC applications in the salt mine at Goderich, Ontario operated by the Sifto Division of Damtarn Inc.

Jan 1, 1986

By Bob Newbery, Kenneth W. P. Eng. Kolthammer

SUMMARY Reference is made to the reasons for drying and the equipment is described that is available from which the engineer can make a selection. The factors affecting this decision are described. In the case of drying, design and sizing are ultimately developed empirically and no theoretical approach has been advanced.

Jan 1, 1986

By S. K. Sharma, D. A. Stanley

The US Bureau of Mines is investigating the fundamentals of the flocculation process. The objective of this study was to determine the effects of various physico-chemical parameters, namely, shear rate, polymer dosage, and polymer concentration, on floc growth and to determine the applicability of a model for predicting polymer flocculation behavior. A rapid in-line particle size analyzer was used to follow the progress of both the floc growth and the breakage as a function of time. A genetic algorithm (GA) was used to determine the unknown parameters in the model and to fit a curve to the experimental data. The results showed that the model reproduces the experimental data with only reasonable accuracy and that it was relatively insensitive to the parameters. Results of the flocculation study showed that increases in the polymer dosage had a greater effect on the time required to reach the maximum floc size than on the floc size itself: It was also determined that, given all the above parameters, the degree of slurry mixing during the flocculation process had the greatest bearing on floc growth.

Jan 1, 1995

By Jack M. Jodrey, Neil D. O’Donnell, R. A. Metz

Bituminous sands of the Lower Cretaceous McMurray Formation in northern Alberta constitute the ore for the surface mining operation at Syncrude Canada Ltd. These sediments represent a complex succession of fluvial, estuarine and marine depositional environments. Grade prediction is realized through a combination of geological interpretation, computer modeling, and reference to past mining experience. Accurate forecasts of feed grade permit reliable predictions of volumes for removal to meet budgeted synthetic crude oil production. This planning facilitates efficient allocation of mining equipment and resources. The feed grade to the Extraction Plant is monitored at various points along the delivery system.

Jan 1, 1992

By A. R. Laplante

The mineralogy of the Joe Mann mine differs from that of other deposits of the Chibougamau area that are exploited by Les Nines Camchib Inc. It is characterized by very fine first generation gold and very coarse second generation electrum. Successful processing required adjustments of the processing flowsheet, which includes gravity, flotation, and cyanidation. A study of coarse gold liberation in the gravity/grinding circuit is described. Modifications to the flotation circuit and the reconditioning of a small capacity cyanidation circuit are presented.

Jan 1, 1989

By M. Heger, V. Lund, P. Mongeon, D. Bogunovic, V. Kecojevic

The U.S. coal mining industry consumes a significant amount of energy, primarily diesel fuel and electricity. The continuous global increase in energy demand, high energy prices and environmental issues related to carbon dioxide emission represent a substantial challenge for the mining industry. This paper presents the result of research on development of an integrated data environment system for analysis of energy consumption in a surface coal mine. A case study on an operating surface coal mine is carried out to demonstrate the practical application of the developed system. The research work presented here may be used by mining professionals to help provide the answers to the crucial questions of when, where and how much energy is being used. This developed system represents a framework for efficient management of energy consumption.

Jan 1, 2009

By J. W. Leonard

Gravity based coal/mineral preparation plants must be operated to yield products of a quality satisfactory to existing markets; but, because of historic control problems, recovery is frequently sacrificed to achieve quality resulting in losses of valuable product. Plant control has ranged from intuitive in-plant spot quality judgments made by various operators to gross methods involving such devices as density gauges, floats, grab-sample on-the-spot sink-float tests, etc. Millions of tons of quality coal/minerals are lost to refuse each year, because of the historic lack of a continuous and dependable control system. The result is both serious economic as well as environmental losses. While the economic losses are obvious, less obvious environmental losses, in the case of coal, result from the misplacement of more ignitable quality fuel to refuse banks. A control system capable of supplying a market-grade coal/mineral product, while continuously minimizing product losses to refuse, has until recently escaped technology.

Jan 1, 1991

By Werner Stahl, Karsten Keller

Vibration screens are commonly used not only in classifying bulk material but also in dewatering it. The lack of a comprehensive physical theory of dewatering often leads to difficulties in the design and operation of the vibration screens. Firstly, the dewatering of bulk material will be shown, based on a physical model. Because of the oscillatory motion of the liquid in the bulk, the inertial force of the accelerated liquid and the dripping of water out of the bulk or screen must be taken into special consideration. The physical model put forward shows the effect of the various operations parameters of dewatering screens. The comparison between dewatering theory and practice will be shown by measurements using coal, limestone, etc. Dewatering measurements, which have been conducted on a vibration screen, demonstrate that different vibration frequencies and rates of acceleration lead to different residual moistures. Finally, the possibilities of improving vibration dewatering will be described.

Jan 1, 1995

By A. W. Khair

This paper presents an assessment of modeling techniques in predicting subsidence over longwall areas. Extensive instrumentation, both at the surface and subsurface of three longwall mines in northern West Virginia have been made. Ground movements were monitored during" a three year-period until subsidence ceased in these areas. A comparative analysis of empirical subsidence prediction techniques including, graphical {NCB}, profile function, influence functions (USBM, BAL'S, KNOTHE'S, and zone area) will be presented. A brief geologic and topographic description of each site along with the instrumentation and monitoring program will also be presented.

Jan 1, 1989