Search Documents

By John A. Herbst, William T. Pate, A. Edward Oblad

Dynamic optimization is a cost-effective means to increase production or improve product quality in a plant. Several model-based approaches to dynamic optimization of mineral processing operations have been developed and implemented in plants. This paper reviews the phenomenological models that are the basis for dynamic optimization and the alternative methods of mathematical optimization. These methods range from theoretically complex and costly to implement to intuitively comprehensible and readily implemented.

Jan 1, 1990

By G. Labonte

The behavior of four different redox sensing electrodes (gold spiral, black platinum, chalcopyrite, and galena) during roughing and cleaning flotation is examined and related to the flotation response. Although it is difficult to provide unequivocal interpretations of the different potentials measured, the results indicate that the solution potential (as sensed by the black platinum electrode) is different from that of the pulp potential (gold spiral) and is only weakly related to the flotation response. On the other hand, the potentials exhibited by the gold spiral and the two mineral electrodes are related to the floatation response. The gold and mineral electrodes exhibit different transcient responses during the addition of flotation modifiers (e.g. NaCN, SO2). These responses appear to be related to the reactivity of the minerals and could indicate the conditioning time required to achieve flotation or depression of selected minerals.

Jan 1, 1989

By Bradford F. Townsend, Robin B. Dill, Richard M. Croswell

Innovative geotechnical construction techniques were used to construct three pedestrian tunnels under a building slab-on-grade to allow utilization of basement space for manufacturing. Tunnels were constructed using mining techniques through granular fill soils less than three feet below on-going sensitive manufacturing operations. Project design consisted of jet grout underpinning of exterior foundation walls and an arch of drilled-in grouted horizontal dowels for soil pre-support to limit ground movements during excavation. Permanent tunnel lining consisted of arched steel rib sets and invert struts supported on precast footings encased in cast-in-place concrete slab and side walls and a gunite arch.

Jan 1, 1993

By Bob Clayton, David Readett

Jameson Cell technology has found applications in the cleaning of entrained material in copper Solvent Extraction - Electrowin plants. The materials involved are largely organic substances that have not been totally removed prior to treatment of the rich electrolyte in the tank house. This paper discusses the recovery of the entrained organics in the rich electrolyte streams at Phelps Dodge Morenci in Arizona. Mount Isa Mines in Queensland. Australia and the Olympic Dam Operations in South Australia. The paper details the design, performance, the feed and product characteristics, capacity and operation. In one operation the entrained material has been observed to include crud that has been formed in the SX train. The mechanism of recovery is also discussed.

Jan 1, 1993

By T. Hudaverdi

Airblast, the focus of the paper, is defined as blast induced atmospheric pressure waves. High overpressure levels may cause breaks of windowpanes, and plaster cracks. Additionally many mines come across psychological responses of residential areas. In this paper the monitoring of air blast is explained and evaluation procedures are defined. The allowable limits of the air blast are presented. The scaled distance approach developed for the prediction of airblast is explained. For the very rapidly growing cities, like Istanbul, the required raw materials for the construction industry are supplied from quarries in the vicinity or from inside of the city. With further growth of the population density, many quarries approach suburban areas and it will be more important to minimize the adverse effect of the blasting operations in the near future. In this paper the airblast levels that monitored in Cendere Region Quarries near Istanbul are presented. The suggestions put forward to control airblast levels.

Jan 1, 2006

By John K. Kellis

With the cost competitive nature of material mining, the ability to actively monitor the condition of the conveyor belt systems without personnel dedicated to that task is very desirable. This paper discusses the development of a conveyor belt condition monitoring system, which actively monitors the conveyor belt, without the need to install special antennas. A belt width map can be generated, as well as detection of three types of physical damages: (a) failure of mechanical fasteners, (b) reduction in belting strength due to reductions in competent belt width, and (c) longitudinal belt rips.

Jan 1, 2000

By Robert H. Merrill

The art of rock mechanics has been applied in various forms since early man first used caves for housing and fashioned rocks into weapons, tools, and utensils. The development of the science of rock mechanics has occurred in a slow but steady fashion due to the complexity of the materials, geometries, and loading conditions involved. It encompasses a great diversity of topics ranging from techniques for rock destruction to those required for rock strengthening or support, and as such enters daily into the life of the mining engineer. Although today rock mechanics can be confidently used in competent geologic structures, the degree of confidence diminishes as the structures become more complex and the number of geologic defects become more numerous. Even so, the principles still give a better estimate of the structural behavior of underground openings than ever before, and the persons responsible for design and control draw freely and often on the subject. For the most part, the civil engineer will spend more time and money on pre-design than the mining engi-

Jan 1, 1982

By Thomas D. Barkand

Investigation of several serious hoisting accidents identified machine brake failure as the most common cause. The recent revelation of this potential hazard has prompted regulatory authorities to require an additional, independent, emergency braking system. As a result of this initiative, a new generation of braking systems have been developed and applied to mine elevators. This paper will discuss the design and testing of an electrical dynamic brake, pneumatic rope brake, and traction sheave brake. The effect of compound braking on hoisting systems equipped with multiple brakes will also be addressed.

Jan 1, 1992

By O. J. C. Runnalls

Canada has played a significant role in the international uranium industry for some three decades. Although there have been many challenges in the past, the future offers a more extensive range of problems and prospects as Canada moves to expand its activities in all aspects of the nuclear fuel cycle. World uranium demand could grow to an annual requirement of 500,000 tons U308 by the year 2000. A substantial fraction of this material is likely to come from Canada because the country's reserves and resources are large, and because of a favourable geological potential for future discoveries. There has been a long history of association between the producing industry and the federal government, and it has provided the foundation for existing national uranium policies. Close industry-government association will be maintained and developed in future because of the anticipated rapid growth of the industry and the consequent need for continual refinement of government policies relating to exploration, mining, processing and export of uranium.

Jan 1, 1975

By Andrew H. Stearn, Robert O. Agbede, Edward F. Divers

The ability to compete profitably in a competitive, demanding and specialized market, requires all components of productivity to be optimized toward the same manufacturing goal. This ever present requisite is seldom more apparent than with the quality control (PC) considerations that confront the super-refined metallurgical production necessary for today's exacting technical applications. In a work-place that already exceeds all environmental standards for cleanliness, this paper describes the development of specific environmental mechanisms and controls implemented at a titanium processing facility to impact both the minimal air-borne particulate contaminants and excessive process heat generation which are believed to degrade product purity. Based on the analysis of a carefully structured and instrumented field survey, two alternative solutions were proposed to modify the present facility utilizing a forced air (blowing) system. The first scenario requires ambient air to be drawn from a louvered rooftop installation and ducted to specific zones within the plant with appropriate weighted louvers and wall and roof exhausters designed into the system for air control. The second scenario incorporates a properly sized baghouse to be used in conjunction with the first system.

Jan 1, 1991

By D. Hong, K. N. Han

The leaching behavior of rhenium in ammonium iodide solutions with iodine as oxidant was studied. Experiments were carried out in an autoclave to investigate the effects of stirring speed, temperature, solution pH, and iodine and iodide concentrations on the dissolution of rhenium. It was found that a high temperature and a high solution pH were essential for the efficient leaching of rhenium. The dissolution rate was found to be dependent upon the concentration of iodine and iodide. It was concluded that the dissolution of rhenium under the conditions studied was controlled by the mass transfer of iodine with an apparent activation energy of 15.8 kJ/mole.

Jan 1, 1999

By N. D. Cristescu

An analysis of the interaction between a creeping rock and a yieldable lining is presented. The following cases are considered: an elastic lining, a lining made of circular shaft rings that may slide at their joints, a lining made of circular reinforced concrete panels with wooden compressible strips inserted between the longitudinal joints and a yieldable support that has a compressible broken-rock stratum between the support and plane rock. By formulating a mathematical model for the rock-lining interaction, one can optimize the sequence of excavation-lining application. To keep costs to a minimum, one can also choose the most appropriate lining for the corresponding rheological properties of the rock.

Jan 1, 1997

By N. Rowlands

The importance of mineralogical and chemical characterization of fine particles in the fields of mineral and metallurgical processing is discussed. Emphasis is placed on electron beam analysis techniques including electron diffraction and energy dispersive analysis with special reference to the scanning trans- mission electron microscope. The correct choice of instrument depending upon particle size, composition and nature of sample is stressed and the analytica1 capabilities of different types of instruments are evaluated. Recent applications of electron beam equipment to processing problems are presented and the paper concludes with a review of new developments in the fields of surface analysis and micro-diffraction.

Jan 1, 1985

By P. K. Davis

The results of a previous basic study of the flow and design characteristics of the hydrocyclone has shown that a recovery as high as 99% with a product rating of 0.95 can be achieved on a "batch?2 basis with a single, water-only cyclone if it is configured properly. The next logical step was to demonstrate continuous processing of gob for the efficient recovery of coal by means of a laboratory-size demonstration system. A project to design and construct such a single-cyclone system was also sponsored by the U.S. Department of Energy. A recovery of 93% with a product rating of 0.89 was demonstrated. The system design and the data taken are discussed.

Jan 1, 1989

By J. L. Fuentes

The so called 'SISCOM' is a General Purpose, microprocessor-based Monitoring and Control System, developed by AITEMIN to meet the requirements of Spanish Mining Industry in - the field of automation and data -transmission. Typical applications -are automatic control of pumps, compressors, fans and conveyors, as well as environmental monitoring and production monitoring. In relation with the last, the - System has been succesfully installed in a full section roadheader and in a mechanised steep coal face. In both cases, the main objective is to get information about running times, down times and causes, -and monitoring of other important parameters such as ventilation, methane content, power consumption..etc. Measurements concerning the face behaviour from a geomechanical point of view are also monitored. These are different pressures and stresses. All data is transmitted to the - surface and on-line analysed by a -desk-top microcomputer. The paper shows the system structure and the requirements that have - been considered on its design. Attention is given to the mechanical data acquisition problem, involving special development of some transducers. The information provided by the surface microcomputer is shown and its utility discussed.

Jan 1, 1986

[The development of economically effective and safe methods of mining thick coal seams enables to involve considerable coal reserves into the energy resources in different countries all over the world.]

Jan 1, 1975

By A. Bayer, T. Klopfer

"As a leading global strategy consultancy, Roland Berger Strategy Consultants firmly believe that the issue of sustainability is at the core of every business activity. Thus, strategies to enhance corporate sustainability (CS) are an essential cornerstone in the consultancy's approach to develop and implement new strategic concepts for the clients. In this paper, the authors conclude that innovation is the only solution possible to guarantee growth and welfare gains while achieving sustainable development. More efficient and effective ways are necessary to enable technical and social breakthroughs. To illustrate Roland Berger Strategy Consultants's vision on CS, four selected cases from the basic resources, energy and utilities sectors are presented. They demonstrate that the implementation of a CS strategy does not only refer to CEO spheres and are by no means just a moral justification for current business practices. Rather they show that the decision to opt for these new ways also opens up multiple opportunities."

Jan 1, 2005

By Hardy J. Smith

The rock mass parameters which need be evaluated to estimate the rippability of rock are briefly outlined and their significance is discussed. Several methods used for estimating rippability are compared, and the advantages of taking into account a wide spectrum of rock mass parameters are emphasized. A systematic means of numerically weighing six rock mass parameters to produce a Rippability Rating (RR) is recommended, and a method of correlating this rating with the refraction seismograph method and with tractor horsepower is shown. Although the overall method demonstrated is systematic and yields specific numerical results, an integrated approach is recommended to its application, taking into account: the Rippability Rating; seismic velocity and geologic material; and other engineering judgment factors.

Jan 1, 1986

By James Lett

The role of pre-conditioning in a caving operation has multiple benefits, ranging from assisting with improved caveability, normalising fragmentation and improving draw point hang-up frequency. At Newcrest Mining’s Cadia Operations, both the Ridgeway Deeps block cave the Cadia East Panel Cave have utilised pre-conditioning using hydraulic fracturing. Seismic response data inside and outside the pre-conditioned volume show the benefit of treating the full caving block. Cadia East has further developed pre-conditioning to mitigate developing seismic hazards associated with major structures (fault-slip events) and managing mine-wide seismic hazards in new caving operations where the potential for large damaging seismic events exists due to high stresses and hard competent rockmasses. A case study reviewing the impact of pre-conditioning to mitigate seismic hazard associated with fault slip is presented. Cadia East operation undertook a targeted hydraulic fracturing program and reduced the overall number of large events as an example of the benefits of pre-conditioning. This paper will review the application of Hydraulic Fracturing at Cadia and discuss the geotechnical and seismological parameters of seismic events that occur within and outside of pre-conditioned rockmass volumes to demonstrate the benefits that Hydraulic Fracturing bring to future caving operations.

Apr 26, 2022

By B. J. Arnold, C. D. Harrison, R. A. Lohnes

More than 544 Mt (600 million st) of coal are handled annually for use by this country's coal fired power plants. Coal is transported in various ways: overland conveyors, railcars, trucks and barges. It can travel short distances or thousands of miles, picking up moisture, freezing or drying. When the coal is received at the power plant, environmental problems with fugitive dust and further handling problems can arise. To ensure that power plant availability is not jeopardized by coal handling problems, the Electric Power Research Institute's (EPRI) Coal Quality Development Center (CQDC) developed a research program aimed at addressing utility coal handling problems. The program has identified key areas, and is investigating the cost and cause of coal handling problems as well as the solutions to these problems. The ultimate goal of the program is to develop a "handleability index" that utilities can use in their coal specifications or hardware for a utility's sampling system to predict handleability and determine if a coal shipment should be accepted.

Jan 1, 1993