Search Documents

By L. K. Lepley

A marine sonic sub-bottom profiling system and a hovercraft were used in an engineering geophysics survey of the tailings being deposited at the Mercur gold mine. Detailed density sections with vertical resolution of one meter were desired for computations of strength, permeability and potential self-compaction. The logistical problems of conducting a geophysical survey and in collection of geotechnical soil samples from an active tailing impoundment was solved by using the amphibious hovercraft for towing and transport on the impoundment. The "chirp" sonic system produced continuous, real-time geophysical cross-sections with vertical resolution of ten centimeters showing possible trapped gas. The hovercraft provided a platform over water, ice, slurry, and solid beach for collection of geotechnical information and physical samples.

Jan 1, 1994

By P. Venkatasubramanian

The selection of a mining method for a mineral deposit is a complex decision problem. Human judgment, based on experience with mineral deposits and geologic conditions, remains the single most important input of the decision-making technique. If the use of artificial intelligence, in particular the developments in expert systems, is taken to its logical conclusion, the experience of the domain experts could be incorporated into a decision-support expert system. A knowledge-based decision support system for mining method selection for ore deposits has been designed whereby the domain knowledge is represented as production rules and organized in a semantic tree representation. This model is written in the PROLOG language. While the verification difficulties of expert systems models are recognized, an example of the model's decision on the mining method for a given ore body is presented and shown to be consistent with the decision made by human experts. In addition, plans, for further verification of the model are delineated.

Jan 1, 1992

By B. Rao Pothini, Julio H. Thaler, W. L. Finlay

The White Pine room-and-pillar mine started in 1955 from a suboutcrop, down gentle dips, and with a competent sandstone roof. As mining depths increased, extraction decreased 1% every 35 feet. Moreover, roofs became shaly and less competent, and regions of high fault and joint densities, sometimes with and some- times without high lateral stresses, increased the tendencies towards roof falls. Instinctive reactions towards narrower openings did not alleviate the problem. Careful consideration of rock mechanics principles culminated in the development of two variants to the conventional room-and-pillar mining system based on the concept of stress relief through load deflection. The two systems-EquiAdvance Cave, and PressureArch Panel Mining-are complementary. The objective of the former system is to provide relief from lateral stresses through advance caving and in the process also to achieve higher extraction at depth. Where surface subsidence cannot be allowed, the alternative PressureArch Panel concept is utilized to provide stress relief and moderately high extraction ratio. Both systems have been under trial for over three years and, together, produced over three million tons of copper ore. These two systems, and their production test results to date, are described.

Jan 1, 1977

By F. L. Jackson

When using perlite as an insulation, it is important to determine the requirements for different applications as this influences the processing of the perlite. In cryogenic application, perlite properties of low density and fine particle size are desirable, while loose fill insulation applications require similar properties and water repellency. However, in perlite insulating concrete applications, a coarser particle, of higher density, is required to provide improved compression strength. The essential properties of perlite including particle size, density, and surface treatment are discussed in relation to the various insulation applications. Also, typical mineral processing and manufacturing techniques are reviewed.

Jan 1, 1987

By Alexander N. Winchell

"The deposits of the east end of the Mesabi Range cover very large areas, and consist of the same taconite that produces the hematite of the central and western Mesabi. It is not deeply covered with drift, but outcrops boldly in large masses. It is not concentrated locally into enriched bodies separated by leaner areas, but is all a fairly uniform, hard, banded, unaltered chert, carrying about 25 to 30 per cent iron as magnetite.The Mesabi Iron Company, organized by Hayden, Stone & Co., and under the direction of D. C. Jackling, has taken over these deposits and is building a Concentrating plant at the new town of Babbitt, about fourteen miles east of Mesaba, Minn. This plant is to have a capacity of 2,000 to 3,000 tons per day, and is based on the application to this low grade material of the methods which have made the so-called porphyry copper properties so successful.In 1916, an experimental mill was built in Duluth; containing full sized machinery and capable of handling from 100 to 200 tons daily. A considerable tonnage of material was concentrated here during 1916, 1917 and 1918. The work showed that the resulting product could be varied, almost at will, between 60 per cent and 70 per cent iron and .006 per cent to .030 per' cent phosphorus, and that this could be made on a large scale well within the limits of cost set by iron trade conditions. A small special cargo was sent down the lakes, late in 1918, assaying 63.27 per cent iron (natural and dry) and .008 per cent phosphorus; but it is assumed that large scale shipments will normally be of a Bessemer' grade carrying about 63 per cent iron and .020 per cent to .030 per cent phosphorus. This material is a sinter, carrying only traces of sulphur and titanium, with silica between 6 per cent and 10 , per cent, and alumina, lime, magnesia, and manganese, each below 1 per cent. Some of the iron in this sinter is hematite and some is magnetite, the percentages varying according to the treatment given on the sintering machine. Like the analyses, this hematite percentage is within reasonable control. Sinter made from finely ground magnetite has much the structure of coke, being firm yet porous, and gives good account of itself in the blast furnace."

Jan 1, 1920

By C. Zhou, B. Whisner, J. Carr

Proximity Detection Systems (PDSs) are used in the mining industry for protecting mine workers from striking, pinning, and crushing injuries when they work in close proximity to heavy machines such as continuous mining machines (CMMs). Currently all Mine Safety and Health Administration (MSHA) approved PDSs are magnetic field based systems which can be influenced by the presence of wire mesh that is commonly used for supporting roof and ribs in underground coal m ines. In this paper, researchers at the National Institute for Occupational Safety and Health (NIOSH) characterize the influence of the mesh on the performance of magnetic PDSs by measuring the magnetic field difference around a CMM caused by the presence of the mesh. The results show that the magnetic fields are generally enhanced by the mesh which causes the PDS detection zones to be increased correspondingly. It was discovered that the fields around the joints of two mesh sections have the greatest enhancement and thus deserve more attention. In addition, it is found that the presence of mesh can also cause a variation in the generator current. The influence of mesh is characterized by the change in the generator current with respect to the distance between the generator and the mesh. It was found that the generator current change caused by the mesh can be significant (on the order of ten) when the mesh is extremely close to the generator (e.g, less than 1 cm) and is negligible when mesh is relatively far (greater than 0.15 m). The findings in this paper can be used to develop guidelines and best practices to mitigate the influence of mesh on PDSs. INTRODUCTION The Mine Safety and Health Administration (MSHA) requires operators of underground coal mines to equip place-changing continuous mining machines (CMMs) with proximity detection systems (PDSs) to protect mine workers from striking, pinning and crushing injuries when they work around these heavy machines. Although a variety of technologies can be implemented for proximity detection, the magnetic-field-based PDS that was originally developed at the National Institute for Occupational Safety and Health (NIOSH) has shown great effectiveness in challenging mining environments and currently all MSHA-approved PDSs are magnetic-field-based systems. As shown in Figure 1, a magnetic PDS typically includes two major components----the magnetic field generator and the Miner Wearable Component (MWC). Magnetic fields are generated by injecting a high electric current into a ferrite-rod antenna sealed in the generator. The magnetic field strength detected by an MWC varies with the distance between the MWC and the generator. In a typical PDS, multiple generators are mounted on different locations of the machine. The relative location/zone of an MWC is determined based on the field strengths from different generators picked by the MWC. Ideally, for a PDS to work properly in the underground, the magnetic fields generated by the different generators should be stable and not vary with the environment, as the system would interpret any variation of the magnetic field as a result of the distance change between the machine and the miner wearing the MWC. In reality, however, this is not always the case since magnetic fields can be altered by a number of environmental factors such as the presence of steel wire mesh that has been widely used in underground coal mines for supporting roof and ribs In this paper, the influence of mesh on the PDS performance is investigated and the magnetic field change caused by the mesh is measured.

Jan 1, 2019

By Robert M. Rowe

Among the increasing operating costs affecting today' s processing facilities are those necessary in meeting the continually growing requirement for safe and environmentally sound materials- control and handling procedures. Of particular interest are materials listed as hazardous, the need to maintain accurate records of their acquisition, consumption and disposal, and the obligation to employees and the community to have information available regarding such materials. Some requirements affecting modern operating facilities are reviewed in this paper, and potential methods for dealing with complex handling and documentation requirements, including computer automation, are discussed.

Jan 1, 1991

By G. D. Schena

A decision support system for the management of the mineral resources of a developing country has been derived. The system allows the evaluation of the impact of a mineral project in a developing country in the broad context of its economy. The analysis permits the assessment of the overall socio-economic consequences of mineral prospects and allows incorporation in the evaluation of issues that are broader in scope than the pure financial objectives. The system is built around the Leontief framework of economic analysis. The original input-output model, enhanced to incorporate country-specific behaviour is integrated with cost-benefit analysis and shadow pricing. The analysis leads to synthetic measures of profitability at market and shadow prices. These measures are useful to direct the mineral policy of a developing country through the exploitation of those mineral resources which are most likely to bring about economic growth and social advancement.

Jan 1, 1992

By G. A. Weisenfluh

The successful application of factors limiting the? availability of coal in eastern Kentucky depends on ac-curate assessment of the original resources. Examination of several previous coal-resource estimates for the region reveals significant differences among the outcomes. These differences relate to methods of analysis, biases in data and their utilization, and the problem of defining the lateral continuity of mineable beds. Improvements in the methods of estimating the original resources would greatly enhance the reliability of the results of the Coal Availability Program.

Jan 1, 1995

By P. C. Rath, K. Srinivasa Rao, T. Subbaiah

A process for the recovery of nickel from ammoniacal leach liquor through an integrated solvent extraction-electrowinning (SX-EW) flowsheet was tested on a pilot-plant scale. The objectives of the test run were to assess the reproducibility of laboratory-scale data in a large-scale continuous operation and to study the build up of impurities in the system. The pilot-plant test was conducted under operating conditions that were established from the laboratory-scale experiments. Efficiencies of nickel extraction, nickel stripping and ammonia scrubbing were comparable to the laboratory-scale values, whereas the current efficiency during nickel electrolysis was observed to be less than the laboratory-scale values. The electrodeposited nickel contained some cobalt and iron impurities.

Jan 1, 1998

By Gerrit V. R. Goodman, Fred N. Kissell

The Bureau of Mines has evaluated the effectiveness of the safety elements used to prevent tunnel methane explosions. These fa1l under the general categories of better ventilation, better gas monitoring, reducing ignition sources, and improved worker training. For this evaluation, a technique called fault-tree analysis was used to analyze questionnaire responses from 27 tunneling experts. This analysis allowed us to rank the effectiveness of each safety element, and indicates where money is best spent to reduce the chance of a methane explosion. Results indicated that large decreases in the explosion hazard only take place with the simultaneous application of several elements. Most of these involve a human component - the everyday vigilance and awareness of those working underground.

Jan 1, 1991

By T. T. Chen, J. L. Jambor, J. E. Dutrizac

A reconnaissance study of the neutralization potential of 30 diverse minerals, 28 of which are silicates and aluminosilicates, has shown that most of these minerals contribute minimally to the neutralization potential (NP) in standard static tests. Feldspars in particular give low NP values and would not be expected to attenuate the acidity to any significant extent in acid rock drainage settings. The BET-determined surface areas of the minerals vary considerably, and the large surface areas of some of the pulverized samples have clearly affected the NP values even though the standard static-test protocol was used for the preparation of the samples. The low NP values of most silicates and aluminosilicates are in general agreement with the laboratory-determined slow dissolution rates for these minerals. The results suggest that, in the prediction of whether rocks will be acid-producing, the most realistic measure is that of the carbonate content. In mine wastes from metalliferous ore deposits, the contribution to the NP by the non-carbonate gangue assemblage is unlikely to be more than a token amount until well after the establishment of an acid rock drainage situation.

Jan 1, 2000

The implementation of NAFTA in January of 1994 was expected to have small but beneficial effects for the Mexican economy, mostly through increased investment flows. Mexico's mining industry was especially likely to benefit, as mineral investment funds would be diverted to the now safer Mexico and away from similarly endowed but more risky Latin American mineral economies. The results of the past two years have shown that it is governments and macroeconomic factors that influence investment flows, rather than the fine-tuning of trade flows through so called "free-trade" agreements.

Jan 1, 1996

By Timothy J. Matthews, Ted Klemetti, Timothy J. Batchler, Daniel J. McElhinney

Unplanned tailgate collapses and difficult mining conditions in U.S. longwalls have necessitated the use of innovative tailgate support systems. Severe ground movement induced by longwall loading has caused operators to utilize secondary support systems that can match yield and strength requirements with expected ground reactions. Standing support performance requirements depend on the nature of the ground deformation behavior, and therefore require a good understanding of the interaction between the support and ground to achieve an optimum roof support system. Mining operations often employ standing support strategies that are unique to their mine. A support system that functions successfully in one situation could fail in another situation. It is important that the design and installation of the standing support systems provide the highest probability of preventing roof falls. Pumpable roof supports are currently being used to provide a safe working environment for longwall mining. A full understanding of the impact of these performance characteristics is necessary to optimize the support application and to provide a foundation for making further improvements in the support performance. Optimization of roof support applications helps to ensure the protection of mine workers by preventing roof falls due to inadequate support design. The load capacity and stiffness characteristics of a 27-in.-diameter pumpable support system was evaluated using the National Institute of Occupational Safety and Health (NIOSH) Mine Roof Simulator (MRS). Previously, tests to evaluate the performance characteristics were performed on a single pumpable support. The goal of this new research is to evaluate the performance characteristic effects of the pumpable support system and compare it to an individual pumpable test examination. This research of a pumpable support system configuration simulates the current installation practices in U.S. coal mines.

Jul 1, 2023

By A. Moergeli, Philip Sander, John J. Reilly

"Estimating and managing the costs of complex infrastructure projects – in the planning/design and construction phases, for both owners and contractors – has been a challenge for decades. The more complex and technologically advanced the project, the greater the uncertainty, including potential risks that are important to owners and contractors, such as:• Cost risks to owners – meeting budget and schedule, maintaining public credibility.• Cost risks to contractors – profit, consequences of loss, impacts to reputation/future work.This concern has been addressed in various ways by the underground construction industry for some time (Reilly, 2001). In particular, while significant advances have been made in cost estimating for the planning and design phases (Reilly et al., 2004), that are important to agencies and political decision-makers, it is not apparent that these advances have been widely adopted for construction cost estimates. The reasons for this may relate to lowbid considerations – any method that tends to increase the contractor’s cost estimate, by including risk or likely costs, could lead to an erosion of the contractor’s competitive position – if others are not similarly required to include such costs.Different cost estimating methods produce different levels of information. Specifically, there is a large difference in the character and depth of information if a deterministic (quantities times price plus a contingency) and risk-based cost methods are used. It is this difference in character and depth of information that is the reason that risk-based cost estimating has potential value for owners and contractors. Figure 1 presents hypothetical cost results from deterministic and risk-based methods and illustrates some of these differences.In Fig. 1, the results for deterministic and risk-based cost estimates are given related to the potential profit or loss for a typical project. As is evident in this example, there is significant potential for costs to be realized that are higher than the proposal/bid value estimated using a deterministic approach, with a 15 percent probability of a loss. There is a 30 percent probability that the project will have a reduced profit. There is a 55 percent probability that the project will return a good profit. Using a risk-based approach, it is possible to better recognize this potential outcome in the bid phase and, as a consequence, develop a strategy to:"

Apr 1, 2016

By K. T. Brashear, N. Ripepi

"Over recent years, specifically following the MINER Act of 2006, an increasing number of manufacturers of underground mine seals in the United States have begun using a form of pumpable cement or shotcrete to create barriers separating the working and abandoned sections of underground coal mines. This seal material, while generally considered to be homogenous and solid, contains a network of microcracks, voids, and delaminations. Generally, it has been assumed that methane (CF4) leakage around these seals is a result of movement around the boundary interface between the seal and surrounding strata. Using a perfluorinated tracer compound, perfluoromethyl-cyclohexane (PMCH), the movement of gases can be monitored through seal material to observe how gases move though the material, both intact and with faulting in the material. This paper documents two large experiments where the movement of PMCH was monitored in the field, along with modeling confirmation using 3D visualization software. INTRODUCTION According to a report in 2007, there were over 14,000 active mine seals in underground U.S. coal mines alone (Zipf, Sapko, & Brune, 2007). These seals are used for both ventilation and safety purposes, to direct the flow of air away from the abandoned area of the mine and to help eliminate the propagation of explosions that can occur on the outby side of the mine seal. The atmosphere on the outby side of these seals typical consists of low levels of methane that have the potential of producing leakage along the face of the seal on the inby side. Methane leakage around mine seals has historically been attributed to the permeability between the seal and mine interface (McPherson, 1993). According to the United States Bureau of Labor Statistics (BLS) between 2003 and 2012 an average of 17 deaths occurred annually in underground bituminous coals mines. The only time during the ten-year period where the fatalities were higher than the average was in 2006 and 2010, years which had three major explosions occurring in underground coal mines in West Virginia and Kentucky. Two of the explosions were propagated through the mine by seal failure or methane leakage around newly poured seals (Light, et al., 2007) (Gates, et al., 2006). These recent events, and new regulations regarding seal strength (MINER Act), have created a need to monitor the condition of underground mine seals. BACKGROUND Measuring the permeability of solid materials, such as concrete or seal materials, can be a valuable tool in the field of non-destructible testing (NDT). By using an inert gas, such as nitrogen, injecting the gas into a solid structure, and measuring the resultant flow rate and pressure differential, this can provide valuable information about the structure. Studies have shown permeability can be affected by the stresses applied to the structure, as well as temperature and moisture (Choinska, Khelidj, Chatzigeorgious, & Pijaudier-Cabot, 2007) (Abbas, Carcasses, & Olliver, 1999)."

Jan 1, 2015

Surface contamination of minerals during fine grinding may occur due to coating of one material on the other. This can alter the surface chemical properties and adversely affect the separation of minerals by physico-chemical processes. In dolomite-silica system, selectivity was completely lost (compared to a synthetic mixture) after wet grinding of the minerals in spite of using a dispersant. Adsorption and surface characterization studies were conducted on silica particles separated after grinding with dolomite. SEM-EDAX analysis indicated the presence of dolomite on silica particles, which could cause the loss of selectivity.

Jan 1, 1993

By Juan Eduardo Barrera

SUNNARY AND CONCLUSIONS Argentina presents to the foreign and local investors a mineral wealth that is largely unexplored, untested, underdeveloped and therefore incompletely evaluated. In view of the above, the new administration of President Raul Alfonsin through its Department of nines has designed and implemented a strategy ( Plan de Expansión Ninera P.E.M.), whose main objective aims at improving the "investment climate" in the sector. It is the Government's basic intention to apply the Mining Promotion Law with responsibility but with generosity to encourage the attraction of investment (local and foreign) to the sector. The establishment of a Data Bank system to evaluate possible new potential ore mining developments will help to connect the owners of potential projects with investors outside the sector. Argentina has an interesting gold ore potential. Estimated reserves of individual projects already known amount to almost 300 tonnes of gold for potential production. The government strongly believes and present information indicates that more systematic exploration has to be undertaken in the Jurassic areas that almost cover the whole of Patagonia. Two recent gold discoveries (Angela in the Chubut province, and Cerro Vanguardia in Santa Cruz province) indicate the potential of this area.

Jan 1, 1988

By A. Janwong

Ion exchange technology is becoming more prevalent for metal recovery from low concentration solutions. The products of ion exchange are typically a metal free stream (product stream) and a concentrated metal stream (byproduct). The metals in the concentrate stream are usually precipitated and returned to the process or discarded. The unique features of emew® technology enable metals to be recovered directly from the concentrated stream. The advantage of the IX-emew® combination is the ability to have two product streams: 1) clean metal free solution and 2) metal product for sale. In addition to recovering metals from solution, it is also possible to separate metals from each other and recover more than one metal product. In this paper, examples of IX-emew® combinations are detailed including the recovery of copper, nickel and cobalt from an industrial waste stream, recovery of nickel from a spent electroless nickel plating solution and recovery of cobalt from an hydroxide cake.

Feb 23, 2014

By Dirk van Zyl, Clint Strachan

A study was conducted to assess the feaeibility of increasing the heap height above one lift at the Alligator Ridge Mine. This study concentrated on the physical aspects of the heap and liner performance. Two principle aspects were addressed during this investigation: (a) the adequacy of heap permeability under present and future loading conditions; and (b) the adequacy of the liner to limit seepage losses. Field and laboratory test a were performed and their details and results are presented. It was concluded that the permeability of the heap would remain adequate for higher heap. The geometry of the heap will be the major constraint. It was also concluded that the liner would perform satisfactorily beneath higher heap.

Jan 1, 1987