Search Documents

By G. Hoffmeyer, I. Ream

"Several copper projects exclusively utilizing in-situ recovery methods are currently under development in Arizona. Favorable conditions for In-Situ Copper Recovery (ISCR) include a saturated orebody, fracture hosted mineralization, hydraulic conductivity sufficient to effectively inject and recover solutions using wells, and a relatively flat background hydraulic gradient. Safe operation of an ISCR project requires that the operator have the ability to induce and maintain localized hydraulic gradients, thereby controlling the movement of injected and recovered solutions. Benefits of ISCR include reduced initial capital, and a greatly reduced environmental footprint. THE ISCR METHOD EXPLAINED The method chosen to extract a mineral from a deposit is driven by characteristics such as its size, grade and depth of burial. Large lower grade deposits that require significant excavation to access using surface methods are potential candidates for in-situ recovery. ISCR may also be ideal for smaller deposits due to the lower initial capital. However, regardless of the size of the deposit, certain hydrogeologic conditions must be present for ISCR to be successful. In-situ recovery methods do not require excavations of rock from the surface or underground, resulting in a dramatic reduction in surface disturbance when compared to conventional mining. With the ISCR method, what is visible above ground is the processing plant, well heads, piping, process solution impoundments and evaporation ponds. There are no waste rock piles, tailings impoundments, leach pads, or impacts associated with blasting and hauling. Other benefits include reduced initial capital, reduced dust and noise, and lower water use. Early testing of the in-situ copper recovery method by Occidental on the Van Dyke deposit east of Phoenix and by Kennecott at Safford Arizona in the 1970s produced encouraging results, but the permitting regime for a large-scale operation was not yet in place. Additional testing and commercial application of in-situ copper recovery techniques have expanded since the 1980s, most commonly in conjunction with open pit or underground mining operations. For example, several operations in Arizona (San Manuel, Miami East and Tohono) have used in-situ techniques to extract additional copper following conventional mining from parts of the deposits adjacent to open pits or underground workings. Where the rock has been broken up by conventional methods, the method is called “in-place” leaching. The US government has also been involved in assessing in-situ techniques. For example, joint research was conducted by the US Bureau of Mines and industry on the Santa Cruz deposit in Arizona; and both federal and state agencies have been involved to establish the comprehensive permitting regime that exists today. Currently there are several projects in Arizona being evaluated as stand-alone ISCR operations."

Jan 1, 2016

By Larry J. Hughes

Ground-based electrical geophysical techniques have be valuable for three indirect exploration strategies: "tracer" sulfide mineralization, 2) mapping structure with or controlling mineralization, and 3) mapping proven to 1) mapping? associated alteration zones. When sulfide mineralization is associated with gold, it often can be mapped using induced polarization (IP). This technique can detect pyrite in amounts as small as 0.2% by volume, and in some cases can distinguish pyrite from anomalies due to graphite and clays. A case history illustrates mapping sulfides in a shear zone. Structure and alteration mapping are often the domain of controlled source audio-frequency magnetotellurics (CSAMT) due to the superior lateral resolution and depth penetration of this technique. Typical CSAMT targets include silicified sediments and volcanics, faults, brecciated zones, argillic alteration, clay and graphite horizons, and certain lithologies. Examples of mapping silicification and mapping epithermal alteration are presented in CSAMT case histories over Cannon mine in Washington and Hishikari mine in southern Japan. In our experience, four things are needed to use geophysics effectively in precious metals exploration. First, the explorationist must correctly identify the exploration stage at which the geophysics is most useful. Second, the explorationist must clearly define the types of "tracer" mineralization, host geology, or alteration which need to be defined by the geophysics. Third, the right electrical technique needs to be applied to the problem to provide the best chance of success. Fourth, the explorationist must be willing to commit adequate finances to do the geophysics properly. With careful adherence to these principles, geophysics can greatly enhance exploration success while reducing the total cost of exploration.

Jan 1, 1989

By A. Pezzuto

"Pipes are used on mine sites in a variety of applications including transport of slurry, conveying clean and processing water, and in mine dewatering. Mine waters and slurries can cause pipe wear and failures via several mechanisms (or combinations thereof) such as abrasion, scaling, and corrosion. Polyethylene (PE) pipe materials have grown in popularity over the past several decades due to their chemical and mechanical properties (e.g., inertness, flexibility, relatively low density) and low cost. While PE is generally resistant to corrosion, it is subject to abrasion. To combat this, a novel, rubber-like liner is in development. In addition to comprehensive abrasion testing, however, the liner must be evaluated to see how it performs under other conditions. Here, a brief field study is described that tested PE pipes with the new liner against traditional PE pipes to specifically assess mineral scale buildup. The study was conducted in the Reiche Zeche study mine in Freiberg, Germany in six different locations with varying water qualities and flow conditions. INTRODUCTION Water and slurry conveyance are major operations on and around mine and mill sites, from mine dewatering, to tailings transport, to water treatment processes. Conveyance systems in such applications can include great lengths of pipe materials along with pumps and monitoring instruments, and thus represent significant capital investments. Due to the variability of the physical and chemical properties of water and slurries, pipe materials are subject to a wide range of conditions. These can cause pipe wear and eventually failure leading to serious economic, environmental and social, consequences. While pressure-induced pipe failures (e.g., ruptures or ""bursts”) can be immediate, most failure mechanisms involve gradual processes. Scaling and sedimentation can present major problems for pipe systems conveying highly mineralized waters. Sedimentation generally refers to the deposition of suspended solids, such as sand, clay, silt, or organic matter onto pipe surfaces. This phenomenon can occur due to a decrease in water velocity or particle collisions with the pipe wall. Scaling, on the other hand, commonly refers to the deposition of precipitated mineral salts (including oxides and hydroxides) onto pipe surfaces. Mine waters often have extremely high ion concentrations (i.e., high dissolved solids content) due to their interaction with enormous surface areas of minerals, which are exposed during mining and processing operations (Brown and Barley, 2002). As these waters are transported, slight changes in temperature, pressure or chemistry (e.g., pH or ORP) can cause instability with respect to ion solubility such that salt precipitation begins to occur. “Seed” crystals can rapidly grow and attach to pipes, either due to local surface phenomenon near the pipe wall (e.g., which can promote coagulation) or sedimentation of the precipitated solid. Whether due to suspended or precipitated solids, as the solids begin to stick to pipe walls, “aging” or hardening processes can commence; and the build-up of scale can become self-perpetuating as the scale itself provides an attractive “nucleus” for further attachment of particles or crystal growth (Muryanto et al., 2014). Over time, scale-buildup reduces the effective pipe diameter, which can ultimately result in decreased flow velocity, clogging and, in some instances, bursting (Dirany et al., 2016)."

Jan 1, 2017

By Frank F. Aplan, Robert S. Thomson

A placer ore jig, typically used to recover fine gold, tin and diamonds from alluvial ores, has been modified to remove fine pyrite from minus 6.4 mm (-114 inch) coal. In parallel tests, it proved to be far superior to two conventional coal jigs, the Baum and the Baum-feldspar, in removing fine pyrite from coal. The Pan-Am placer jig was found to remove essentially all of the +28 mesh pyrite and from 99% to 90%, decreasingly, in the 28 to 200 mesh range. This jig also showed a superior performance to the Baum-Type jigs in removing fine coal from its associated refuse. The superiority of the Pan-Am placer jig is related to the strong emphasis given on the suction stroke and, hence, on consolidation trickling, whereas the Baum jigs principally emphasize the pulsion stroke during jigging.

Jan 1, 1995

By D. Veigel, J. D. McKay

Model enhanced Expert control has been implemented at the Newmont Lone Tree mill grinding plant as well as rule based Expert control for flotation and thickening circuits. The project has been successful in producing benefits but more importantly has contributed to an ongoing effort for continuous process improvement. This paper discusses how the control at Lone Tree has evolved and the part that Expert control has played in the overall improvements made. Specific examples of how the advanced control has integrated with instrumentation and stabilizing control are given and illustrations of how it has been effective in defining limitations and bottlenecks in the process or process control areas are provided.

Jan 1, 2002

By J. H. Desautels

The modern coal mining industry is subject to a vast array of regulations affecting virtually all aspects of its operations. Probably the most significant over-sight role involves the Office of Surface Mining Reclamation and Enforcement (OSH) established by the Surface Mining Control and Reclamation Act, or SHCRA.1 Although complying and coping with SHCRA can be difficult for coal operators, this complex regulatory process has helped insulate the industry from ongoing efforts to extend regulation under the Resource Conservation and Recovery Act, or RCRA, 2 to aspects of the mining industry in general. The Environ-mental Protection Agency (EPA) has struggled with regulation of mining wastes under RCRA since the mid-1970's, but RCRA itself places most coal mining wastes firmly under the control of OSH and SHCRA. Despite the general exemption from RCRA regulation for waste materials that result from extraction and processing of coal itself, there may be circumstances under which coal mining operators could find themselves subject to regulation under RCRA or a number of other statutes administered by EPA. This paper will review briefly the history of mine waste regulation under RCRA, as well as touch on the policy decisions that led to the exemptions from RCRA regulation. The paper will summarize coal waste requirements under SHCRA, and also will review what operations at coal mines need to be controlled, in order to avoid potential liability under RCRA. In addition, it will mention requirements under other federal laws, including CERCLA, or the "Superfund" law,3 and describe how they may impose restrictions or liability on coal operations for waste or other materials commonly found at surface and underground coal mines.

Jan 1, 1993

By B. Mishra, K. Savage, T. Evans, A. Noble

"Recent government initiatives and commercial activities have targeted asteroids for in-situ characterization, manipulation, and possible resource extraction. Though emergent technologies may be effective for such undertakings, uncertainties remain concerning the effects a space environment may have on the mechanical behavior of rocks. Various non-destructive rock characterization techniques can empirically predict in-situ rock strength on Earth; however, these techniques must be adapted to account for unique space conditions. In order to mimic one element of a space environment, various rock samples were evaluated after prolonged exposure to low temperatures ranging from -75°C to 0°C. Tests included uniaxial compressive strength, Schmidt hammer, and ultrasonic pulse velocity, while rock types included shale, limestone, and chalk. This data was used to generate a temperature correction for the non-destructive methods and evaluate the accuracy of these methods in predicting strength values. Overall, these results provide insight on the mechanical behavior of rocks at low temperatures and may be used to design robust systems needed for asteroid rock characterization INTRODUCTION NASA and various commercial entities have recently targeted near-Earth asteroids for exploration and scientific investigation to better understand their in-situ properties, mechanical characteristics, and formative processes. In particular, NASA’s Asteroid Initiative encompasses several studies and mission plans that will enable future investigations while vetting technologies that can be applied to deep space exploration. One component of the Asteroid Initiative is the Asteroid Redirect Mission (ARM). This multi-stage space mission proposes to rendezvous a robotic spacecraft with a large near-Earth asteroid. Upon approach and after landing, the spacecraft will prospect the surface and identify a multi-ton boulder (up to 5 m in its largest dimension) suitable for capture. The robotic spacecraft will engage the boulder, remove it from the parent asteroid, and return the sample to a controlled lunar orbit. Once the asteroid mass is in stable orbit around the moon, astronauts aboard the Orion spacecraft will engage with the retrieved asteroid for manned exploration that will include sample collection and geologic prospecting. Launch plans for the ARM robotic craft are expected as early as 2020, and manned explorations of the asteroid mass in lunar orbit are expected to follow sometime in the mid-2020s (NASA, 2015). Overall this mission will demonstrate NASA’s ability to intersect, manipulate, and redirect an extraterrestrial body, while supplying scientific information that is relevant for planetary defense and in-situ resource utilization (ISRU) applications."

Jan 1, 2016

By M. A. Marticorena, R. Stratton-Crawley, C. I. Basilio

Diethylenetriamine (DETA) is a selective depressant for nickeliferous pyrrhotite during pentlandite flotation. Laboratory flotation tests conducted on ore and process samples showed that pyrrhotite rejection is greatly improved by small additions of DETA; however, the effectiveness of this depressant is most noticeable when the mineral sample is oxidized. LIMS and XPS analyses conducted on flotation products and pyrrhotite specimens showed that the difficulty in pyrrhotite rejection arises from inadvertent activation of the mineral by heavy metal ions, such as Ni2+, cu2+ and Ag+, that are present in the process water. In the presence of DETA, however, the mineral is deactivated under oxidizing conditions. The deactivation mechanism may involve oxidation of the activation products, which are likely in the form of heavy metal sulfides, followed by solubilization by DETA. FTIR spectra of pyrrhotite electrodes contacted with DETA showed no trace of the reagent on the surface, substantiating the view that its role is one of complexing agent that enhances the dissolution of activation products under oxidizing conditions. FTIR spectra of pyrrhotite contacted with amyl xanthate solutions showed that both dixanthogen and iron xanthate are formed on the surface, the latter becoming more predominant at higher potentials. In the presence of DETA, however, only a small amount of xanthate is adsorbed on the mineral at potentials (Eh) approximately 200 mV higher than the case without DETA.

Jan 1, 1995

By Stephen Meyer, Véronique Falmagne, Antti Pyy

Kittilä Mine is a gold mine located in Northern Finland, owned and operated by Agnico Eagle Finland. The mining operation started in 2008 with open pits which were completed in 2012 and production moved to being entirely underground. The mine consists of four separate orebodies, currently producing 2.0 Mt per annum, and requiring over 19 km of development on a yearly basis. The principal mining method is long hole stoping with delayed backfill. Microseismic monitoring was initially tested in the Suuri orebody, in the mining block between the 625 and 500 Levels. A small monitoring system was installed in 2018, after observations of stress-induced damage to the rock mass and in anticipation of future mining at greater depth. The initial goals were to evaluate if useful data could be recorded and test the signal quality of different sensor types. Prior to 2018, ground control related challenges in the Suuri and Roura mining blocks had been mostly related to sill pillar mining and block movements between weak graphitic schist planes. Seismic monitoring in the Suuri deposit proved successful for following the rock mass response to mining and helped support the rationale for early monitoring in the new, deeper mining block in Rimpi at 900 m depth. Preliminary geotechnical characterization and testing of the rock mass showed areas of silicification in the footwall rocks with potentially continuous structural features. Seismic monitoring of the Rimpi area has confirmed the brittle behavior of the rock mass, with strong seismic responses induced by stress changes following blasting being recorded. In addition to this expected behavior, a large magnitude event associated with significant damage in the footwall drive development 90 m above the stoping was experienced. Initial investigation of the rockburst showed two separate damage locations with over 300 tons of displaced rock. The seismic monitoring system recorded this rockburst as a single seismic event with magnitude significantly larger than previously recorded. Additional analyses indicated a possible thrust fault event, triggering two separate strainbursts. Following this event, the ground support system was upgraded in parts of the footwall drives to improve dynamic capacity. Systematic calculation of the source mechanisms for the small footwall events down to Mw-2.5 has revealed potential planar structures in the footwall. Early implementation of microseismic

Apr 26, 2022

By E. B. Kroeger, Y. P. Chugh

The goal of this project is to develop, demonstrate, and document the beneficial use applications of a ponded F-fly ash as a road subbase material for the 2.1-mile Meredosia Industry Access Truck Route in Meredosia, Illinois. Approximately 60,000 to 70,000 cubic yards of ponded fly ash are proposed for use on this project without negative environmental impacts to surface water or groundwater. The County Highway Truck Route will consist of a 24-foot wide road built on a 0 to 7-foot thick compacted F-fly ash subbase. Laboratory testing indicates this fly ash will serve adequately as a road subbase, conforming to IDOT standard specifications. The economic considerations of using the Meredosia F-fly ash will also be developed so that a detailed cost-benefit analysis can be prepared for this project and for future projects. This project represents a two-year cooperative development and demonstration effort among the Office of Coal Development and Marketing (OCDM) of the Illinois Department of Commerce and Community Affairs (IDCCA), Southern Illinois University (SIU), Morgan County Highway Department (MCHD), Illinois Department of Transportation (IDOT), AmerenCIPS, and the Morgan County Regional Planning Commission. It is anticipated that monitoring activities will continue for a period of three (3) years after the completion of this project. The MCHD and IDOT will oversee all construction activities and long-term performance evaluation studies. Successful demonstration of large-volume beneficial use applications of F-fly ash at this site will significantly reduce management costs for power plants burning Illinois Coal. Furthermore, it will encourage similar utilization strategies at other sites in the State of Illinois.

Jan 1, 2002

By F. Allen Meek

The Upshur Complex of Island Creek Coal Corp. consists of approximatly 35.000 acres of both surface and deep mine researves located in Upshur County West Virginia. The principle seams on the researve are the Middle and Lower Kittanning. Other mining in the area during the late 1960's and early 1970's produced surface mines that exhibited severely acidic drainage characteristics both during the mining phase, and after reclamation was completed. The Buckhannon River, the principal drainage for the area, is a high quality, lightly buffered stream, that is periodically stocked with trout. Because past mining had caused post mining acidic discharges and the Buckhannon River was a valuable recreational resource, mining permits for the area were put on hold by regulatory authorities, until solutions to the acid mine drainage questions could be addressed. In 1978, the director of the West Virginia Department of Natural Resources appointed a Task Force consisting of Industry, Regulatory. and Academlc participants. This Task Force was charged with gathering information and evaluating field procedures used during mining to prevent acidic mine drainage. In 1979, the group published a document titled "Suggested Guidelines for Mining in Potentially Acid Producing Overburdens" which summarized material handling and mining procedures that could be employed to help prevent the occurrence of post mining acid mine drainage. In 1982, a Technical Advisory Committee was appointed consisting of well known researchers in the field of acid mine drainage prediction and prevention. The group was charged with the task of conducting research in the field of acid mine drainage prevention. Mining conducted at the Upshur Complex between 1979 and 1986 employed various acid mine drainage preventative techniques recommended in the suggested guidelines manual and techniques concurrently being researched by the Technical Advisory Committee. Costs for the various techniques were documented and the resulting post-mining water monitored. The results of these evaluations are used by Island Creek in the planning of future mining operations in potentially acid prodcuing environments

Jan 1, 1991

By Jack G. Pippenger

This report focuses on the procedures required to review, prepare specifications, bid, and purchase a fully integrated computer system for utilization by engineering personnel in all phases of mine engineering. The presentation is based on the experiences encountered in 1984 in procuring an engineering computer system at The North American Coal Corporation's Western Divi- sion. A two-phase report detailing the purchasing process and subsequent utilization of the engineering computer system will be given. Special detail is also provided on the final system hardware and software setup.

Jan 1, 1989

By S. J. Jung, F. Lock

This research came about because of the recognized need for a safe, easy way to line small-diameter bored raises (less than 150 cm). Currently, an operator must go down the raise and apply the concrete lining manually, using the shotcrete method of application. With an automated system, there would be no man positioned in the bore itself. All control functions could be commanded from a central location. Shotcreting in the confined space of a small-diameter bored raise presents problems that can be overcome by the application of shotcrete using a remote system.

Jan 1, 1995

By Brian H. Kaye

Efficient design of grinding circuits for efficient production of ultrafine material requires rapid feedback of information concerning the fineness of material leaving the grinding device Generating this information requires efficient sampling and adequate rapid characterization of the material leaving the grinding machinery Recent developments in electrooptic inspection of dry and wet material leaving a grinding device are critically reviewed New methods for characterizing ultrafines are discussed A rapid operating automated cybernetic (intelligent) permeability device for automatic control of grinding circuits using Blaine Index and other fineness indices is described

Jan 1, 1983

By B. C. Cornilsen, X. Shan, D. H. Carlson, J. H. Johnson

Airborne respirable Diesel Particulate (DP) presents an additional health hazard in that it has been shown to be mutagenic. This problem is of increasing concern as more coal mines introduce diesel vehicles. If the DP present in coal mine air is to be controlled it must first be measured. This paper describes development of the laser Raman spectroscopic measurement of the amount of DP in DP/coal mixtures collected on filters in the laboratory and in coal mines. The Raman technique provides a chemical measure of the carbonaceous material in each component, and is not dependent upon particle size. When this work was begun there were no known analytical methods for this measurement. Side-by-side in-mine comparisons of the results obtained from Raman, neutron activation analysis, and size selective analyses (MOUDI and personal samplers) are presented. The neutron activation and size selective analyses were obtained by the USBM Twin Cities Research Center and University of Minnesota. Good agreement has been found among these three methods.

Jan 1, 1991

By F. F. Peng, Y. Xia

In modeling of hindered-settling bed separators, the published separation mechanisms are based on differences of particle density and size distributions, without the details of complexity of particles-liquid interactions. A fluid dynamic model for the separator is developed using Euler-Lagrange approach of Computational Fluid Dynamics (CFD). Fluid motion is obtained from solving the movement of liquid governing equations. The damping effect on flow pat-terns caused by the movement of particles resulted in liquid-particle coupling is included in the model. Effects of particle size, and particle density compositions, feed rate, feed water flow rate, upward fluidizing water flow rate, etc., are simulated in the 2-D separation model. Flow pattern effects on the separation of fine particles in the separators with center downward-flow and side cross-flow feed systems are investigated.

Jan 1, 2004

By L. Laage, R. Greur, W. Pomroy

MFIRE is a mine ventilation and fire interaction computer simulation program. It allows transient state ventilation simulation and features mass based flow rates, natural ventilation, air recirculation, fan curve fitting, airflow reversal and product of combustion tracking. MFIRE was designed to accommodate the needs of the mining industry, for routine ventilation calculations and mine emergency planning. This paper describes recent work by the US Bureau of Mines and Michigan Technological University to improve MFIRE by incorporating humidity in the mass flow and heat exchange calculations, a data file preparation program, and variable reference density in the network calculations. Recent bug fixes are also discussed.

Jan 1, 1995

By Donald R. East

There has been an increasing trend in recent months by regulatory agencies to require that estimates be made of the hydraulic head acting, under operational conditions, on the surface of primary leach pad liners. This move towards inferred performance standards, rather than specifying a prescriptive standard for all sites regardless of economics, is to be generally welcomed. The theory of flow on a sloped beach pad, which was developed by East et al, 1987 (Reference 1 and 3) has been refined and extended. Unitized curves have been developed by graphically displaying the seepage losses and resulting dissolved gold lost as seepage through the primary liner as an aid to pad liner selection and design. Very little information is available of actual hydraulic head profiles acting on the liners beneath heap leached ores. Attempts have been made to measure these by drilling from the top of the heap and installing piezometers at the base. With this procedure it is difficult to obtain accurate data due to the fact that the drilling operation itself creates a highly permeable vertical flow path which may not exist to the same degree elsewhere in the heap. Combined with the fact that it is almost impossible to ensure that the piezometer tip is sitting directly above the liner without the risk of causing some damage to the liner itself. The best time to install hydraulic head monitoring devices on the pad liner is during construction and when piezometers can be carefully placed directly above the liner and suitably protected hydraulic lines laid to ensure full hydrostatic head measurement with simple manometer devices.

Jan 1, 1998

By L. Bloom

In 1996, lack of confidence in assaying methods and sample handling affected companies as diverse as Bre-X and Timbuktu. Share prices and the ability to raise financing are impacted when the quality of assay data is suspect. Overseas projects are subject to enhanced scrutiny when local facilities are used that are unfamiliar to brokers, financing agencies and banks. Quality control systems can be implemented but there are associated costs. These costs should reflect the risk to the mining company, investors and financiers and the size of the proposed investment. In this regard, assay control can be considered a form of insurance to enhance the value of an exploration or mining project. Providing reliable assay data in a production laboratory is challenging. Pressures such as time constraints and profitability affect data integrity. In Australia and North America, reliable assaying services have been provided by several laboratories. Mistakes are primarily due to human error but systems are available that monitor results and identify these types of errors. As the mining industry expands globally, mining companies encounter difficulties in some of these areas due to lack of infrastructure, poor communications, bureaucracy and political risk. These challenges also apply to the operation of laboratories, enhancing the risk of compromised data.

Jan 1, 1997

By William J. McCloy, Robert L. Gamble

A coal-fired fluidized bed steam generator rated at 12.6 kg/s has demonstrated the industrial and institutional application of fluidized bed combustion by burning high sulfur coal in an environmentally acceptable manner within a populated area. Designed to provide steam for heating and cooling, the unit was placed into service at Georgetown University in Washington, DC, and has already logged 5275 hours.* The unit has consistently operated well within Washington's strict regulations governing emissions of sulfur dioxide (SO2), nitrogen oxides (NOx), and particulates. The Georgetown program, cofunded by the university and the US Department of Energy, has shown that fluidized bed combustion is a promising way to realize the full potential of coal, the nation's most abundant energy resource. In a fluidized bed steam generator, a layer of granular limestone is placed on top of a grid designed to prevent particles from falling through. Air is passed upward through the bed with sufficient force to lift and float the particles. At this point the bed material resembles a boiling liquid. Crushed coal is then introduced into the bed and ignited. When high sulfur coal is burned, limestone absorbs the SO2 produced. The operating temperature of a fluidized bed steam generator is relatively low (approximately 871°C). As a result, NO, formation is minimal. Another potential problem encountered in burning coal is fly ash, a form of particulate. A feature of the fluidized bed design, developed by Foster Wheeler Energy Corp., is a fly ash reinjection system. Fly ash is reintroduced into the bed where it is burned again, thereby enhancing fuel efficiency. Nearly all remaining fly ash is captured by a baghouse dust collector. At Georgetown, the fluidized bed steam generator and all auxiliary equipment are enclosed in a structure aesthetically compatible with the surrounding university complex. The steam generator has two separate beds that can be fired independently, and operation to date has been with one and two beds in service, based on steam load demand. During several operating periods, when the fluidized bed unit was the only boiler in service, it supplied all the steam required by the 18.5 hm2 of buildings on campus. Initially fired with low sulfur coal, the unit was quickly switched over to higher sulfur fuel which will be used most of the time.

Jan 3, 1981