Search Documents

By Bruce D. McCellan

INTRODUCTION The gathering arm loader was patented by Joseph Joy in 1916. This unique machine motion became the standard of the industry and is used on underground loaders and continuous miners throughout the world. Figs. 1 and 2 show two types of gathering arm loaders. The gathering arm loader is a crawler-mounted ma¬chine primarily used for loading coal in a conventional mining system. Other uses also have been found for this machine in noncoal mines and other industries. MECHANICAL ASSEMBLIES The front or loading end of the machine, commonly called the head, consists of a tapered structural frame, hinged at the rear to the chassis and riding the ground at the front. Two bevel-gear cases are mounted in the head. They are connected by a timing shaft, which also acts as a conveyor drive shaft on most models. An eccentric disk attached to each gear case drives the gathering arms. The rear of the arms are attached to a swivel assembly. The motion derived from this arrange¬ment gathers loose material from the ground directly in front of the machine and loads it into the conveyor. Power for this drive is provided by two electric motors mounted under the gathering head. A speed reducer attached to each motor provides a gathering arm speed of approximately 5.2 rad/s (50 rpm). A torque limiting clutch is provided on each reducer to guard the system against sudden impact loading and continual overloading of the motors. The conveyor consists of an open box section through which a universal-type chain carries the ma¬terial to the rear of the machine, where it is discharged into the haulage vehicle. The chain is driven by a sprocket located on the timing shaft between the two gathering-head bevel-gear cases. On some large loader designs, primarily for noncoal applications, the chain is driven by a separate gear motor at the discharge end of the conveyor. However, the system driven by the timing shaft is used most widely. The conveyor frame is hinged just to the rear of the gathering head. It can be raised or lowered by hydraulic cylinders to the desired discharge height. The conveyor frame also is designed to pivot 0.79 rad (45°) either side of the center, just to the rear of the chassis. This feature increases the maneuverability of the ma¬chine and makes it possible to discharge material into the haulage system when in tight quarters such as when turning a crosscut. This function also is controlled by a hydraulic cylinder. The chassis of the loader consists of two crawler frames and cross members, holding the frames in position. The frames are either welded or cast as¬semblies. Replaceable wear runners are provided on the frames to take the wear generated by the crawler chain. An adjustable take-up idler keeps the crawler chain in proper adjustment for maximum life. The drive system for the crawler chains varies with the manufacturer, but it generally is one of two basic designs. One system provides a traction motor for each side of the machine, coupled to a speed reducer. A spur and bevel-gear train transfers power to the sprocket, which drives the crawler chain. Directional control is achieved by disk-type clutches. The other system also uses a motor for each crawler, coupled to a speed reducer. A roller chain drives the sprocket, which in

Jan 1, 1982

By R. A. Metz, Ted H. Eyde, Dan T. Eyde

Industrial minerals deposits present sampling and grade control problems not normally encountered in metal mining operations. No longer are industrial minerals simply crude ground mineral products but are in fact high purity chemical raw materials. Operators of industrial minerals mines and processing plants now must meet increasingly stringent specifications established by the consumer of the final products. Meeting these stringent specifications requires not only sophisticated processing techniques but equally important careful sampling and grade or quality control at the mine. A well-trained geological staff can assure an adequate supply of uniformily high quality feed to the processing plant. In the final analysis this results in significantly higher operating profits.

Jan 1, 1992

By M. C. Williams, T. P. Meloy

With the increasing power of computers to simulate and control processes in the mineral industry, predicting the potential use of computers in the minerals field is not a hazardous enterprise, but predicting the timing of their use is. Like the railroad industry, technology invades the mineral industry, rather than being an industry like electronics that creates technology. Because of this invasive nature of computer technology in the minerals field, this paper predicts what will be possible to do effectively and economically with computers in the mineral industry. Moreover, this paper explores the problems of using the emerging computer technology in the mineral industry. For example, if not now, it soon will be possible to control the output of a mineral processing circuit - high grade, high flow or a mixture of it - to meet the daily market conditions and to sell each day that daily "mill" output as "mill" futures on the commodity market. Finally, suggestions are made which may be done to prepare the industry for the computer revolution in the mineral industry.

Jan 1, 1993

By G. T. Lineberry, B. R. Yama

Artificial intelligence research has produced several tools for commercial application. Some of the techniques that are widely used today include neural networks, fuzzy logic and expert systems. Artificial neural networks (ANNs) are excellent predictive, pattern recognition and data analysis tools. In the mining industry, ANN techniques are being used commercially for real-time process-control applications. Modeling of spatial data, ore-reserve estimation, tunnel design, long wall-stability prediction and geologic roof classification are additional applications in which neural networks have been applied successfully. In this study, a standard back propagation algorithm was used to train a series of neural networks for a real-world predictive task. After training and optimizing the neural network architecture, the performance of the network is measured on an independent validation set. Results indicate a mean error of less than 1 % between the actual and predicted values. A neural network model was developed for learning the spatial continuity of a mineral field and, consequently, for predicting sulfur values for given coordinates. The neural network not only performed satisfactorily, but in some cases performed even better than the kriging model.

Jan 1, 2000

By A. A. Peshkov, N. A. Matsko, K. N. Trubetskoy

It is possible to divide the general objectives of a company into two components: maximum expected profits and viability over time. These components are designed to maximize the companies value over time. The evaluation of a project includes both a discounted cash flow (DCF) analysis and a risk analysis. The DCF analysis determines whether the project should be accepted or rejected, and the risk analysis helps to forecast possible deviations from the original estimates. However, the results of both methods do not allow for a quantitative comparison between the main objectives of the venture, and they do not resolve the issue of whether it is advisable to sacrifice immediate profits for future profits. This paper attempts to resolve this issue. The present research was carried out on mining projects with different waste-extraction schedules. Calculations were made using the US Bureau of Mines' usage-of-costs model. Russian experience in open-pit mining is reflected in this paper.

Jan 1, 1996

By M. Niinae, Y. Nakahiro, K. Yamaguchi, T. Wakamatsu

The rare earth magnet has a good performance and the production is increasing year by year. Two types of rare earth magnets are presently made as industrial products. One is a Nd-Fe-B intermetallic compound magnet and the other is a Sm-Co alloy magnet. The mixed scraps of Nd-Fe-B intermetallic compound and Sm-Co alloy are sometimes produced in the step of production. Therefore it is desired that a recycling system of mixed rare earth magnet scraps should be established. In the present study, hydrochloric acid leaching of the oxidizing roasted products of Nd-Fe-B intermetallic compound and Sm-Co alloy and solvent extraction of metals such as Nd, Sm, etc. are tested to obtain the fundamental data for the hydrometallurgical treatment of the mixed rare earth magnet scraps.

Jan 1, 1995

By V. Roze, M. E. A. Robertson, C. J. Sharland

Current Techniques - Fire Assay Fire assay of gold has been used for several thousand years and is a well known technique to the traditional assayer. Very few assayers wish to use the method but to date there has been no viable alternative. Fire assay is expensive in labour, time, capital and running costs. Workers can be exposed to hazards and uncomfortable working conditions such as lead fumes, heat stress, dust and eye strain. The high capital cost of putting up the building and equipping it, together with running costs which increase annually at a prohibitive rate makes the technique less attractive each year. The main requirement in most assay laboratories is to maximise throughput economically. This is difficult with fire assay as it is impossible to automate. Each sample for analysis is handled by at least 12 people and each person represents a potential source of error. Record keeping and report generation has to be done manually which is both slow and prone to errors. Replacement of staff requires a considerable training period and with a large turnover of personnel this presents yet another problem. The presence of silver and dross in the gold sample affects the accuracy at low gold values. X-ray fluorescent analysis Two methods of XRF instrumentation have been used with limited success. The first type is a laboratory instrument employing L X-rays. Small samples of a few grams, which are not representative,

Jan 1, 1988

By M. Ghoreychi, M. Fauueau, P. Lebitou, P. Berest

A brief study of the history of gas caverns in salt formations enables us to consider creep mechanism in a cavity as a phenomenon of dissymmetrical deformation. Among different parameters affecting such a phenomenon, gravity forces, especially in large caverns, seem to be responsible for important bottom heaves as compared to roof releases. This fact is demonstrated here by means of certain theoretical considerations concerning elasto-viscoplastic constitutive laws relevant to rocksalt rheological behavior.

Jan 1, 1986

By A. J. Friedrich

Conveyor belts are designed to go unnoticed. When they work well, they attract little attention. When they are not doing the job right, it is noticeable, and they need to be fixed immediately. Vulcanising contractors compete for the maintenance of belts in mining/quarrying and general materials handling worldwide. Damage repair is approached in similar fashion. The damaged section of belting is normally cut out and discarded, and the belt re-spliced using hot vulcanising, Cold splicing, or mechanical fasteners/clip joints. However, there is a cost-effective alternative, alleviating the need to remove damaged sections which are often perfectly recoverable. This is the use of cold-curing repair resins and adhesives.

Jan 1, 2000

By Richard Campbell, MEHMET KIZIL, Ismet Canbulat, Serkan Saydam

The design and effectiveness of ground consolidation to regain stability of longwall faces vary widely and are often based predominantly on-site precedence or what were considered successful applications at other sites in similar situations. Little is known regarding product migration characteristics or change in rockmass conditions as a result of the application of consolidation chemicals. This paper presents the in-situ testing rationale designed and implemented recently across several longwall operations in the Bowen Basin, Queensland, Australia to provide quantitative measurement of the actual zone of influence of various resin injection products. Product migra- tion was physically measured by monitoring the change in rockmass temperature as a result of the exothermic chemical reaction of the various strata consolidation chemicals used. In conjunction with strata coring and Lugeon transmissivity testing pre- and post-injection to characterise the improvement in rockmass conditions due to consolidation product injection. The results of the testing programme, migration measurements, and rockmass assessment are presented, along with a discussion on how site- based Rock Mechanics Engineers can incorporate the data into the design of strata consolidation plans.

Jun 25, 2024

By C. H. Sampaio

The effectiveness of modem spirals in the processing of fines from Brazilian coals is assessed and discussed. Coals representing the four major coalfields in Brazil have been cleaned in Reichert LD 9 spirals in pilot and industrial plants and performance results are here presented. Normalized distribution curves for all equipment and splitters are presented and were modeled using an empirical model. These data have been compared with those for shaking tables and water-only cyclones (WOC), and it has been observed that, in the size interval investigated, spirals have indeed superior accuracy than WOC and comparative performance to tables. By analyzing experimental as well as simulation results it could be observed that although limited by the poor liberation characteristics of most Brazilian coals, significant ash and sulfur removal could be achieved using spirals.

Jan 1, 1995

By Mengxiong Guo, Xuxin Shao, Yong Bao

In the paper, the adsorption properties of dissolved ions on the surface of collophane and dolomite are studied using zeta potential measurement, ESCA and UV adsorption spectrum both in distilled water and in the supernatant of each other. The effect of dissolved ions on the flotation separation of collophane and dolomite under SCO depressant and oleate is discussed on the basis of above analyses.

Jan 1, 1993

By Charles H. Dowding

INTRODUCTION "On many projects, the tendency is to drop interest and support of the geological service as soon as it seems safe. That . . . is a short-sighted policy . . . It would be of further service perhaps to learn whether predictions were reasonably true to life." --C.P. Berkey, 1938 (3) This paper quantitatively compares predicted and encountered shear zone size and location and rock type for tunnels in the Colorado Mineral Belt. The Colarado Mineral Belt is composed of igneous formations with associated metamorphic rocks and faulting. As such, it represents the most complex of provinces for at-grade predictions (27). Shear zone and rock type data are assumed to be statistically homogeneous because of the common geology of the seven tunnels. It is often felt by geologists and engineers that the amount of information from which a geological model is created is so low that any statistical inferences are unstable. In other words, the addition of new data may drastically alter the means and variances suggested by the model. Therefore, predictions are rarely couched in quantitative statistical terms but modified with "probably," "most likely" or "possibly." Comparison of predicted and encountered data from past geological models will permit the "probably's" to be quantified and distilled from the art of geological prediction. To date, two other studies of the validity of predictions have been made (26 and 16). Together, these two studies indicate that

Jan 1, 1976

By Scott Jones, Tony R. A. Durkac, David W. Stephens

Williams Mine was considering spending a large amount of capital to install a pumping system underground to rid the mine of slimes; with the introduction of Delvo Stabilizer this challenge would be met. This paper will address the process to introducing the Delvo Technology into the Cemented Roddill Program. Some areas that were worked on included: testing of the mix design, bet dosage rate for an economical solution, temperatures at different levels of the mine, the amount of time needed once the grout was put to sleep, preventing plugs in the delivery system A controlled dosage that gave the Operator a 12 hour window of flowable material was developed and an added feature to the introduction of Delvo was also noted; an increase in MPa strength over the design. Collectively with the help of operators at the batch plant and the underground miners involved with the program all concerns where addressed and all goals met. A cost effective program was implemented thus increasing productivity, preventing costly plugs, and improved the actual maintenance on the entire delivery system, which included the batch tanks, aggitator tanks, all pumps required in the system and of course reducing buildup of slimes at the cones.

Jan 1, 2001

By G. Le Bel

Discussion by G. Le Bel The paper proposes three methods to determine optimum lifetime of a mining project 1. The conclusion is that the three methods arrive at the same optimum production rate (by coincidence). It is also stated that: "The stochastic and option pricing models, in addition to providing a more realistic optimum mine life than the traditional NPV (net present value) calculation, showed that the example project has the potential for substantially higher return. By explicitly considering a project's potential risks, the stochastic or option pricing techniques can more accurately describe its probable investment performance." This discussion is intended to demonstrate that: •It is no coincidence that the three methods arrive at the same optimum production rate. • The stochastic and option pricing models do not provide a more realistic optimum mine life than the traditional NPV calculation. •The potential for a substantially higher return is misrepresented. First, a review of investment decision theory in mining is needed. Net present value is the preferred performance measure because of the flexibility offered when comparing various alternatives. However, it presents the following disadvantages: • The discount rate selection is not straightforward. • The NPV obtained represents a deterministic characterization of the variables included in the cash flow calculations, i.e. a single-point estimate. Discount rate selection The opportunity cost of capital represents the rate of return that would be obtained if the capital was instead invested in other opportunities considered to exist. Such opportunities must be bypassed if the available capital is invested in the project studied 2. If these other opportunities carry risk similar to the project under analysis (for example, if they are other mining projects), there is no need to add incremental [ ] risk factors. On the other hand, if these opportunities are represented by the acquisition of government bonds yielding 7%, a risk premium factor must be included. The types of risks associated with a mining venture are shown in Table 1. Together they represent the "business risk" of being a mining company. The individual project risk is important to investors if it differs substantially from the business risk of the company and that of the other investments in mining ventures that we must pass up to invest in this particular project. A risk premium or discount would then be required. This can be illustrated by the following example. Consider that a company has two investment alternatives: one is the Cavender hypothetical project located in Nevada, and the other is the same project located in a civil war zone of central Europe. The second project requires a risk premium factor on the discount rate. Conversely, a project showing highly uncertain returns that are negatively correlated with the returns of the firm's other assets may decrease the company's corporate risk. Deterministic character of NPV calculation The cash flows used in NPV calculations are obtained from a set of variables. These variables are estimated using one parameter obtained from the engineering studies. Each parameter is thus a single value that is often termed a "realistic" or "best estimate" as opposed to "optimistic" or "pessimistic." However, considering that each variable can assume a range of values between the

Jan 1, 1994

By D. V. Bush

There has been a great deal of evaluation and discussion on the economics of semi- autogenous grinding versus conventional grinding circuits. This paper will not discuss the merits of one system over the other, but rather will discuss the Henderson Mill's approach toward achieving the most economical milling conditions in its existing SAG mills.

Jan 1, 1985

By G. Deschenes, M. Fulton

The New Britannia Mine processes a qumtz-carbonate gold ore containing 4.63 git Au at a rate of 2,200 tpd. The ore contains approximately 3 .0% arsenopyrite, 2. 7% pyrite and the rest is gangue minerals. Eight to ten percent of the gold is refractory to leaching. Two years ago, New Britannia Mine experienced cyanidation problems. Gold extraction was not stable and occasionally decreased significantly. Preliminary test work, at laboratory scale and in the plant, indicated that lead nitrate addition was beneficial. A laboratory study was initiated to evaluate the level of control of the parmneters (grinding size, dissolved oxygen, pH, free cyanide and lead nitrate) to optimize the efficiency of the process. It was found that lead nitrate addition is required to alleviate the effect of metallic sulphides. This addition causes a significant increase in the gold leaching kinetics and a reduction in the cyanide consumption. The optimum system appeared to be: leaching for 24-30 hours at pH 11.8, 50 git lead nitrate, 250 ppm NaCN and 8 ppm 02. The gold extraction was 89.8% with grinding at 89%-74Fm (leached tail at 0.48 git). Cyanide and lime consumption are 0.40 kglt NaCN and 1.9 kglt respectively. Following the incorporation of lead nitrate, overall gold extraction was increased from 89.2% to 91.1 % but no change was noticed in cyanide consumption. The gross profit is $CDN 988,000 per year.

Jan 1, 1999

By Maynard Stenberg

Judging from the progress made in August 1989, drilling and raise boring of a 400-m (1312-ft) pilot hole at the Elura mine of Pasminco Ltd. in Southeastern Australia, an observer would never guess that the project had been delayed nearly a year. Moreover, two pilot holes had been abandoned in previous attempts. The challenge was to drill a 93-mm (3.66-in.) H size exploration hole between Elura's 400- and 800-m (1312and 2624-ft) levels. The hole needed to be kept within a 300-mm-diam (12-in.diam) target cylinder over the 400 m (1312 ft) distance. The deviation restriction of the initial core hole was necessary to precision ream a pilot hole to 330 mm (13 in.) and then raise bore a 6-m-diam (20-ft-diam) shaft, planned as the primary men and materials access between the two levels. Core was not really necessary to gain an accurate geological picture of the steeply dipping formation. Rather, the core barrel was used because it tended to drill a straighter hole. Using rock bits in the steeply dipping formation would have simply aggravated the problem of deviation. The core barrel and diamond bit optimized the probability of a straighter hole. However, on the first two attempts to drill the pilot hole, the bit was out of the 300-mm (12-in.) target cylinder within the first 50 to 60 m (164 to 197 ft), and the holes were abandoned.

Jan 1, 1990

By R. D. H. Bedd

GEOLOGICAL NOTES The area under discussion is situated approximately 150 m north of Loraine No. 3 shaft at ± 1500 m below surface. The block being mined extends from about halfway between 50 and 52 levels to just below 48 level (see Fig. 1). The EB reefs form the lower portion of the EB zone of the Elsburg series and in the 81 line area the various conglomerate bands show the best development. Up to 18 separate reef bands are developed and the distance from the bottom conglomerate band to the top is ± 26 m. The thickness of the quartzite which forms the middling between the various reef bands varies from 0.1 to 2 m. The strike is roughly north-¬south. The reef bands are payable individually. However, owing to the steepness of the reefs and their close prox¬imity, conventional mining would prove very difficult. The nonpayable reef bands all carry varying amounts of gold and the whole area is a massive payable reef body approximately 26 m wide and 60 m high at 300 to 400 m on strike. The major structure of the area consists of a north¬-south trending syncline. The western flank of the syncline has a steep easterly dip, in places approaching the vertical. This flank cuts out against the overlying rocks of the EA zone. The latter forms a noncon¬formity with the underlying EB zone. The eastern flank of the syncline dips to the west at an average dip of 0.17 rad (10°). The 0.1 rad (6°) north-plunging syncline was sub¬jected to severe faulting. The most important are the Nos. 4 and 10 faults, both of which have a roughly north-south strike. The No. 4 fault dips to the west at an angle of 1.04 rad (60°) with a downthrow of approximately 150 m to the west. The dip of the No. 10 fault is 0.69 to 0.81 rad (40° to 50°) west, with the western block having moved 150 m updip relative to the eastern block. The EB reefs are being mined by the sublevel stoping method down from the sub-outcrop position to the cutoff against the No. 4 fault. On the downthrow side of the No. 10 fault, that is just above the 54 level, two reef bands are payable and will be mined conven¬tionally. ROCK MECHANICS From the section in Fig. 1, it can be seen that the area under consideration is surrounded by stoped-out areas. This will naturally change the stress distribution extensively. The only way to calculate the stress field for such a geometry is to use the finite element method. It was established that this method worked for the present geometry and so the method was applied to predict the stress behavior of the final geometry. From the results, it appeared that the effect of the old stopes was to destress the area. There are, however, some areas-such as the 50 and 48 north footwall haulages-which will require continuous attention. In these two footwall haulages, deterioration can take place due to tensile stress which

Jan 1, 1982

By J. H. Lalor

The Olympic Dam deposit was discovered in July 1975 with the intersection of 38 m (125 ft) of 1.05% copper in diamond drill hole RD 1. A further eight holes were drilled with only marginal encouragement to November 1976 when RD 10 cored 170 m (558 ft) at 2.12% copper and an economic discovery was confirmed. The discovery of Olympic Dam is an excellent example of the application of broad-scale scientifically based conceptual studies to area selection combined with the backing of an exploration management willing to support its exploration scientists in testing their ideas with stratigraphic drilling. It also illustrates the persistence required in mineral exploration. The project began in 1969-1972 with the development of a conceptual model for the formation of sediment-hosted copper deposits. This model suggested that the alteration of continental-type basaltic rocks could release copper into solution from which it could be concentrated in favorable stratigraphic positions. In mid-1972, this concept was applied to a review of the Proterozoic and Lower Paleozoic rocks in South Australia aimed at defining targets for stratigraphic copper deposits.

Jan 1, 1991