Search Documents

By David R. Shaddrick

Ore reserves are based on sampling developed by drilling programs. Correct choices concerning the type of drill to be used, depth of drilling, hole orientation and sample spacing are not only critical to the accuracy of the ore reserve but to the cost in time and money of the project. Appropriate interpretation and use of geologic information can significantly enhance the ability to make these decisions effectively. Geologic characteristics of mineralized rock that affect drilling and sample quality include: rock quality, openness, water content, mode of gold occurrence, internal gold distribution and grain of mineralization. Each of these characteristics and sources of data about them are revuewed, then related to the various drill program options. Finally, some procedures for checking the validity and appropriateness of the selected options are reviewed.

Jan 1, 1987

By Hassan El-Shall, M. N. Ahmad, Ponisseril Somasundaran, C. R. Holland, G. M. Walker, N. Iles, R. D. Chandler, Regis Stana, B. Duddy, Patrick Zhang

Phosphoric acid is a major raw material for the production of ammonium phosphate (AP) that is used as an intermediate in fertilizer production. Impurities within commercial grade wet process phosphoric acid are important in producing a fertilizer granule with good handling properties. The impurities identified as being important are; iron (III), aluminium and fluorine-containing compounds. Results show that the viscosity of the AP slurry produced increases by increasing the amount of impurity in the acid. Bench scale tests have been successfully replicated on a plant scale leading to a better understanding of the composition of impurity levels within phosphoric acid required to produce a high quality, free flowing, hard, spherical and non-caking granular fertilizer.

Jan 1, 2002

By Paulo Roberto, S. M. Roberto, Francisco Valadares Póvoa, Evandro C. Silva

The market of mineral goods worldwide is characterized by a growing pressure on suppliers for better quality products, lower prices and productive processes which are energetically efficient and environmentally friendly. These pressures force the mineral industry to re-think not only the present models of exploitation of natural resources and production, but also their own model of techno- logical development. This paper outlines the model and the experience of Technology Strategic Planning (TSP) adopted by CVRD to face these demands, warranting and expanding its participation in the current markets and developing new businesses.

Jan 1, 1998

By P. D. Pattillo, J. B. Cheatham, Y. -H. Lin

The stability of a hemispherical cavity, intended to model a perforation opening in the vicinity of a borehole, is analyzed for the case of poroelastic-plastic material behavior. Two plasticity models of differing complexity are considered, with the emphasis in either model being the use of strain softening to calculate inelastic stiffness. Sample results illustrate the effect of steady fluid flow on the response, and possible collapse, of the near perforation region.

Jan 1, 1986

By Timothy F. Markey, Brian C. Strohm

This paper presents a case study which applies risk assessment techniques in evaluating potential environmental problems associated with past waste disposal practices at a 65 acre non-ferrous metals and metal alloys manufacturing facility. Waste management activities at the site involved a number of surface impoundments for gangue material, neutralized acid rinse waters, acid rinse sludges, demolition debris, storm water runoff, stockpiled ores, and a permitted residual waste landfill. As a result of these activities, the She contained 9 identifiable waste management areas impacted by over 35 potentially hazardous chemicals and metals. Extensive environmental data obtained from investigations at the Site revealed heavy metal and volatile organic chemical contamination in various environmental media. These data were utilized to evaluate potential risks to human health and the environment. The human health risk assessment estimated potential health risks to workers, residents, and Site trespassers under current and expected future uses of the Site. Areas of the Site were identified which were considered to present potential health concerns under the various exposure scenarios. Results from the human health risk assessment were utilized to develop cost effective risk based soil remediation goals protective of the public health and environment.

Jan 1, 1992

By E. T. Sugar

English China Clays, the world's largest producer of China Clay, has its main production capacity in the South-West of England, where a complex of pits, refining plants, dryers and ports covers an area of approximately 100 square kilometres. The possibility of a computerised information network was first considered in 1980. The system was required to provide information at the central level and also at local plant level to improve co-ordination and control. Immediate access by any authorised user, and flexibility of interrogation were important aims. A small micro-based prototype system was implemented in 1981, and later that year development of the mainframe system commenced. This latter system will provide at least one terminal in every works location and will allow inter-communication of laboratory test data as well as detailed stock levels and production data. An integrated system for order processing will allow stock levels to be monitored in relation to anticipated requirements. The system has been developed by the Data Processing Department using the IDMS database package running on an ICL ME29 mainframe. It was decided to use microcomputers as terminals, which although more complicated because of protocol emulation allows stand-alone applications to be run on the same equipment. Those applications concerning Production Planning are outlined in the paper. Communication on the network is by synchronous transmission over dedicated lines. All data is stored on the central database with terminals accessing it in a star configuration. The system is currently partially implemented with 30 available screens at 18 separate worksites.

Jan 1, 1986

By D. J. Shields

This paper describes a dynamic short-nun mineral supply model that incorporates secondary processing, transportation, mineral market structure, and direct mining and milling costs. The method employed is network flow programming. Empirical tests utilizing domestic phosphate industry data have been conducted by the Bureau of Mines, U.S. Department of the Interior. In the model, nodes represent physical locations such as a mine or port. Arcs represent either a process, such as mining, or movement, such as rail or barge transport. Each arc is described by lower or minims allowable flow bounds, upper or maximum possible flow bands, and variable cost. Mines and previous period inventories represent potential supply. The model is optimized via a cost minimizing algorithm, which attempts to fulfill stated total demand at the minimum possible system cost given the arc constraints. An optimal solution of the model will predict production patterns by mineral property for each prespecified level of demand. A mineral property is defined as a separate accounting entity such as a mine. The results of serial optimizations are used to construct the short-run supply curve. Dynamic policy analysis can be conducted by altering the arc constraints.

Jan 1, 1986

By Ronald C. Bethard, Kenneth W. Ely

The liberation of methane during underground coal mining causes serious safety concerns. During a mining cycle, with mechanized mining equipment, thousands of cubic feet of methane are released from coal seams, discharged to return air courses, and vented to the atmosphere through mine fans. This has been the traditional way of removing the explosive hazards of methane gas from the mine. Through horizontal and vertical degasification techniques, this hazard can often be handled in an equally safe and much more profitable manner. Basically, degasification allows for the controlled reduction of inseam methane content of coal prior to its mining. It is the responsibility of mine management to evaluate these degasification programs and ensure that the program itself does not introduce some new risk to the mining process. The removal of methane gas from underground coal mines using horizontal and vertical degasification is a relatively new concept. Products and systems used in degasification continue to evolve. Site conditions vary also, so no one system or equipment can be said to be the safe answer for degasification in all situations. A constant process of cooperation and evaluation by mining and degasification management should result in a safer and more profitable mine.

Jan 1, 1989

By R. D. Hamilton, W. J. Miles

In 1987, the International Agency for Research on Cancer designated crystalline silica as a 2A probable carcinogen. As a result, crystalline silica is regulated under the Hazard Communication Standard as a probable carcinogen at a concentration of 0.1% or greater in the workplace. Crystalline silica will be listed as "reasonably anticipated to be a carcinogen" by the National Toxicological Program. This designation of crystalline silica as a probable carcinogen has created major issues for the mineral and chemical producer, including labeling, hazard communications, marketing a material with potential hazard exposure, and potential liability. The State of California also regulates crystalline silica under Proposition 65 in products as a carcinogen, based upon the IARC determination that it is a probable carcinogen. More federal and state regulations are anticipated as a result of the IARC classification of crystalline silica and its subsequent federal regulation. Respirable crystalline silica has been regulated as a hazardous dust for many years by OSHA. This regulation was initiated to prevent silicosis, another occupational disease. OSHA has established monitoring devices for determining the concentration of airborne respirable silica in order to measure exposure to this substance. The accurate determination of the crystalline silica content is critical to dealing with these health risks and regulations. In the past, crystalline silica was considered to be safe and, because of its ubiquitous nature, little effort was made to determine or quantify its presence in most materials. The Hazard Communication Standard requires that a1l products containing 0.1% or greater crystalline silica must be properly labeled for this material and its hazard. Unfortunately, the 0.1% threshold was not chosen on the basis of established analytical capabilities for crystalline silica, but results from general limits for potentially carcinogenic chemicals and substances. Numerous methods have been developed for the determination of crystalline silica in a variety of products. However, these methods are not generally applicable since they must be specific for silica in any of its crystalline states and not just for total silica content. Chemical tests for silica are not difficult and quite accurate at the 0.1% level; however, in addition to its crystalline phases, it occurs in amorphous phases and in a wide variety of crystalline and amorphous silicates. In general, there is little correlation between total silica content and crystalline silica.

Jan 1, 1991

By E. K. Albert

In 1977, Congress enacted Title IV of the Surface Mining Control and Reclamation Act (SMCRA), providing for an "abandoned ml.ne reclamation fund". This fund, taken from a fee collected from operating coal mines, provides capital for the reclamation process. However, given the number and extent of abandoned mine sites in some states, the question of project selection is important. This paper describes a project in progress to create a Management Information System application for project ranking under multiple objectives. The benefit of this project for the need of new environmental control technologies will be discussed.

Jan 1, 1990

By P. Massacci

This study deals with the development and utilization of computer models for evaluating the extent to which variability of raw material grades can be reduced from the deposit to the processing plant. The specific case of a cement works is examined. The deposit and the elementary quarring operations were modeled for the medium and long-term planning of production with the objective of predicting grade variability of the flow stream in time. The feeds inferred from previous modellings were used for simulating storage operations. In particular, the storage process (linear stockpile, as an alternative, blending from various heaps) was modelled in order to select the main parameters of the process to minimize grade variations of the feed to mill. The ways followed for modelling the prehomogenization process are described. The homogenization performance and efficiency in the silo stage has also been studied and an estimate made of the distribution of residence time on the basis of input and output sampling.

Jan 1, 1986

By J. A. Farinelli

In the Appalachian region of the United States, approximately 40% of the underground coal reserve base exists in seams 0.7 - 1.1m thick. These seams are, in general, often of premium quality and are frequently accessible through above-drainage drift-type openings. Unfortunately, there are no apparent advantages to mining thin seams, if quality is disregarded. The thin-seam mine is faced with the same legal and economic pressures as any other underground coal mine. But in addition to these common problems, thin-seam operations must also deal with the unique problems associated with mining at such a restrictive height. Small-scale, short-lived operations appear to be the most feasible means of mining these reserves. The purpose of this paper is to evaluate the production and safety potential of various thin-seam mining systems. Recommendations will be made regarding present and future thin-seam operations.

Jan 1, 1987

By John E. Tilton

Mining is one of the oldest human activities. It goes back at least to the Bronze Age and possibly even the Stone Age. The Romans mined copper in Spain and tin in England some 2,000 years ago. The writings of Agricola in the 16th century show that mining was important in the Middle Ages. Today, more mineral commodities are mined in greater tonnages than ever before. This long and fascinating history closely tied with the economic development of the human race is one of the charms of the mining industry. It also, unfortunately, gives rise to some widespread misconceptions. Old industries are generally considered stodgy with mature and stagnant technologies. Costs tend not to decline as in newer industries, and may even increase with real wages. Costs are particularly expected to rise in the case of mining as the best mineral deposits are depleted. Thus, mining is often thought of as a sunset industry, destined to decline over time as the resource base is depleted. These perceptions have several important implications. They argue against economic policies that rely too heavily on mining and mineral processing to foster growth and development. The best and the brightest young people, along with society's other valuable resources, should be encouraged to enter newer industries. There the technological opportunities and the prospects for growth are more promising. These perceptions also suggest that the ability to compete in the mining industry depends largely on the quality of a company's or country's mineral deposits. Mining will take place first in countries with the lowest-cost deposits. Once these are exhausted, mining will shift to countries with the next best deposits. From time to time, new discoveries may also produce a shift in the location of mining, [ ] and may even for a time keep the costs and prices of mineral products from rising. Over the longer term, however, rising costs and prices are inevitable, as the world is forced to exploit poorer mineral deposits.

Jan 1, 1997

By M. E. Smith

Chile is the world's largest copper producer and as such sets the standard of practice in copper SX/EW design. The authors summarize the liner systems used at many of Chile's major copper producers both operating and planned. The evolution in the state of the art is also discussed, considering both economic factors and Chile's burgeoning environmentalism.

Jan 1, 1994

By Ryan Lemmon

Belt turnovers are commonly used in conveyors to rotate the belt so that the clean side of the belt contacts the return idlers. The belt turnover length has traditionally been sized on only the twisting stresses. However, belt turnovers are also subjected to bending stresses due to the weight of the belt. Although bending stresses have in the past been ignored, these stresses are significant and should not be neglected. This paper quantifies and presents a method for calculated twisting and bending stresses and also the belt sag.

Jan 1, 2002

By Kuda R. Mutama, Allen E. Hall

A wind tunnel investigation into the fundamental characteristics of jet fan performance is described. The effects of varying fan positioning in a square tunnel cross section are reported for two fan outlet diameters and velocities. Tests were conducted, also for a jet fan placed in a flow developed by an external fan operating in the same direction as the jet fan. The position of the jet fan relative to the tunnel walls was found to affect its performance. Performance parameters were determined and used to formulate theoretical equations based on momentum and energy considerations. The results identified a range of flow ratios which can be used to design an effective jet fan ventilation system and provide a basis for the selection of jet fans for practical mining applications

Jan 1, 1997

By Robert Irvine

Exploration activity for diamonds in Canada has recently experienced a dramatic increase. Disclosure of a diamond discovery exhibiting features of a potentially economic deposit contained in a kimberlite pipe in the Lac de Gras area of Canada's Northwest Territories has sparked substantial interest in-Canada and abroad and has triggered the largest staking rush in terms of area in the history of Canadian exploration. In this paper, we report on the nature and extent of current exploration activity in Canada for diamonds (with special attention to Arctic regions), the results of this activity to date, and the context in terms of current world markets for diamonds.

Jan 1, 1995

The trend in the U.S. coal industry in recent years has been a continuous increase in the percentage of coal produced by surface mining methods. Though the predicted energy demands promise a good market for coal, growing legal and environmental issues make the exploitation of a coal deposit by surface methods a difficult and challenging task. Major emphasis has to be placed on the development of integrated mining and reclamation schemes which enhance the possibilities of post mining land uses. Since no major breakthroughs are foreseen in the near future in surface mining equipment, innovative applications of current equipment must be developed. Draglines have been and are expected to continue as the primary earthmovers in surface mining of coal. A dragline simulation model has been developed which has the capability to analyze various deployment schemes such as conventional side casting, advance benching, and extended benching. The mathematical aspects of the model, the input data, and the output results are discussed with reference to an application in an operating mine. The model can be used to select a suitable dragline for given geological and mining conditions and to study the effect of alternative mining layouts and spoiling plans on machine production.

Jan 1, 1979

By W. J. Pennstrom, J. R. Arnold

This paper focuses on solution-balance management around heap-leach operations. Experience has shown that increased leach recoveries can be achieved by utilizing various leach-solution recirculation techniques. The most prominent solution-recirculation technique is intermediate leaching. The net effect of intermediate leaching is to increase recovery plant performance by increasing solution concentration tenors, to increase metal recovery by increasing the total leach time and to decrease the overall capital expenditures required for metal-recovery facilities. The adverse effect on the flow of cash from increased metal inventories in the recirculating solutions is offset by increased metal recovery and lower operating costs per unit produced.

Jan 1, 2000

By H. Suharyono, R. Hogg, P. Bunnaul

The flocculation of fine-particle suspensions by polymers is a nonequilibrium process whose performance is strongly influenced by physical as well as chemical variables. A standardized test procedure has been developed that provides quantitatively reproducible measurements of process performance in terms of the floc settling rate, supernatant turbidity and sediment compressibility. The procedure provides information on the development of flocs in response to polymer addition and on their degradation behavior during subsequent handling. Extensive experimental observations using a variety of solids and flocculant types have been used to develop criteria for reagent selection and process design. It is shown that the appropriate choice of reagent(s) is determined primarily by chemical factors (solid type, solution chemistry, etc.). However, actual performance depends more on physical variables, such as agitation intensity and the rate of flocculant addition. Some general guidelines for flocculant selection and process design in industrial applications are suggested.

Jan 1, 1994