Search Documents

The declining grades of surface deposits have re-confirmed the need for greater production rates. Large scale production requires increased investments in expensive and sophisticated equipment. The key to successful operations can depend entirely on proper equipment utilisation and in this program of research at the Department of Mining and Metallurgical Engineering, University of Queensland, much emphasis has been placed on the analysis and improvement of this aspect of a load-haul-dump operation. For a model to be successfully integrated into a mine engineering function and readily accepted by mine operating personnel, it has to offer more than just results. The concepts used in its design and construction must include sufficient detail to enable engineers to apply it usefully and with confidence.

Jan 1, 1979

By Michael J. Shulman

During-all phases of exploration limited resources must be allocated among exploration methods and among exploration prospects. This problem,, an exercise in optimization, can be treated mathematically. For three objective functions - maximizing return, return to cost and return minus weighted cost - theoretical results exist which enable the exploration planner not only to gain valuable insight into the problem, but also to estimate the resources necessary and to allocate these resources for' at least-two stages of exploration prior to initial field work. A two-stage exploration strategy for volcanogenic-sedimentary iron in northern Egypt illustrates, how the results can be used. Stage 1 consists of an aeromagnetic survey to map the structure of five areas;" stage 2 consists of field reconnaissance work. For the three objectives, lower bounds are calculated as a function of exploration expenditures for each stage in order to facilitate the choice of an-optimal exploration budget. Nomograms are then presented which, based on the Kuhn-Tucker Conditions', enable the incremental allocation of airborne and reconnaissance effort among the five areas.

Jan 1, 1989

By K. H. McDaniel

Eight Mine Weather Stations (MWS) installed at the Waste Isolation Pilot Plant (WIPP) to monitor the underground ventilation system me helping to simulate real-time ventilation scenarios. Seasonal weather extremes can result in variations of Natural Ventilation Pressure (NVP) which can significantly affect the ventilation system. The eight MWS(s) (which previously collected and stored temperature, barometric pressure and relative humidity data for subsequent NVP calculations) were upgraded to provide continuous real-time data to the site wide Central Monitoring System. This data can now be utilized by the ventilation engineer to create real-time ventilation simulations and trends which assist in the prediction and mitigation of NVP and psychrometric related events.

Jan 1, 1997

By W. C. Smith

Even with the most conservative mine plan, rib instability can occur unexpectedly, and if not adequately dealt with, can progress from a nuisance to a major safety hazard. This Bureau of Mines paper examines the mechanisms of progressive rib failure in high mine openings and discusses techniques to control rib slabbing. A field test site in a longwall mine was instrumented to investigate rib behavior during mining. While data analysis showed minor pillar dilation, sporadic zones of progressive rib instability were detected which culminated in eventual rib failure. The failure occurred despite conservative pillar dimensions and shallow depth. Physical and computer models were used to demonstrate the mechanisms of rib failure and then evaluate the influence of support and other mine-related parameters on rib behavior.

Jan 1, 1989

By Zhang Youdi

According to general guidelines, deposits suitable for surface mining can be divided into two basic categories: horizontal or flat-bedded deposits and inclined or dip-buried deposits. A series of mathematical models for surface mine long-term planning (SMLTP) has been developed and can be used for any kind of deposit. The basic theory and methodology of the models are oriented- graph simulation which combines graph and network theory with a systems simulation technique to form a new approach. From the viewpoint of surface mining and long-term plan modeling, the main differences between the two categories of deposits are analyzed, an important algorithm is put forward, and the structure of the models and some results of applications are introduced. Dynamic and comprehensive optimizations have been completed by the SMLTP model series. Combining different OR branches, the new approach has been proved to be a powerful tool to solve the strategic problems of surface mine planning.

Jan 1, 1989

By G. A. Kosick, L. Kuehn

The design of an information management system (IMS) for a mineral processing plant requires prior consideration of many factors, which can be broadly categorized into two domains, process plant considerations and IMS considerations. The process plant considerations include: plant characteristics, management and personnel issues, existing organizational standards and policies, and the level of existing hardware and software systems. The IMS considerations include: system functionality, system sizing and desired performance, hardware components, software components, and system support issues. All of these aspects must be addressed in order to achieve a functionally successful and cost effective system. The purpose of this paper is to lay out these design issues and, in doing so, to provide process engineers with a guideline with which to tailor a system that is best suited to their specific application. The paper is completed by presenting an approach that has been used in two Canadian concentrators. Both of these plants have incorporated MillEX, a software system designed specifically as the central component of a mineral processing IMS.

Jan 1, 1993

By Jeong-Heum Kim, Jan M. Mutmansky

A number of solution methods for solving the nonlinear equations derived from mine ventilation networks use meshes selected from the network as the basis of the solution techniques. Mathematicians working in network theory have outlined several methods for speeding up the computations through mesh selection and ordering procedures. In the mine ventilation area, a fair amount of attention has been paid by ventilation specialists to procedures for choosing the meshes so that the computational effort is eased. However, little attention has been paid to mesh ordering methods. This paper outlines research into random mesh ordering procedures plus two non-random mesh ordering procedures and compares some results using these procedures within four solution algorithms.

Jan 1, 1993

By Keith P. Bingham

A total transportation system providing for delivery of finished products to customers and raw materials to the plant is one of the key elements contributing to Dravo Lime Co.'s success. Dravo Lime operates one of the largest noncaptive lime and limestone plants in the US at Maysville, KY, where products produced can cost as much to deliver as they do to manufacture, depending on the product itself, its destination, and mode of transportation. With delivery costs comprising a significant portion of total costs for its products, Dravo Lime has made total transportation services an integral part of its business strategy. Prices for most products produced at Maysville are quoted f.o.b. destination. In short, Dravo Lime's Distribution Department relies on the approach that says to customers: "Leave the delivery to us." The 0.9-Mt/a (1-million stpy) Maysville facility, located about 121 km (75 miles) east of Cincinnati, OH, on the Ohio River, primarily produces sulfur-absorbing Thiosorbic lime used by coal-fired electric utilities as a scrubber reagent to remove SO2 from stack gases. The product is currently supplied to eight power plants in the Ohio River valley region which extends through portions of Kentucky, Indiana, Ohio, West Virginia, and Pennsylvania. The plant ships approximately 907 kt (1 million st) of lime and a comparable amount of limestone fines each year. In addition, it arranges for delivery of about 181 kt (200,000 st) of coal to the plant. Lime is transported by covered hopper barges, covered rail cars, covered dump trucks, and pneumatic trucks. It is transferred from barges to storage silos and trucks at a terminal on the Ohio River near Marietta, OH. At another terminal near Aliquippa, PA, lime is transferred from barges to silos, trucks, and rail cars. Future plans call for rail-truck transfer terminals. To produce lime from limestone at the Maysville plant, about 181 kt (200,000 st) of coal is burned annually in three coal-fired kilns. In transporting this coal from the mine to Maysville, Dravo takes maximum advantage of opportunities for reloading carriers with limestone for outbound backhaul movement. Coal, shipped from southeastern Kentucky mines in rail cars, is transferred to barges at a river terminal in West Virginia. After it is unloaded at Maysville, the barges are cleaned with a front-end loader and then reloaded with limestone. Limestone also is backhauled in connection with truck deliveries of coal. The economics of using backhaul shipments has permitted Dravo to enter into markets in which Maysville limestone otherwise would not be competitive. The company plans to backhaul limestone in empty open hopper cars in the future. As part of its ongoing assessment of the distribution system that supports the Maysville operation, Dravo Lime recognizes that a new environment has developed between shippers and carriers because of regulatory changes in the railroad and trucking industries. Although dry bulk shipments by barge to and from Maysville have always been unregulated, other forms of transportation have not. With railroads and motor carriers now approaching varying degrees of deregulation, contracts and agreements are replacing tariffs, and rate negotiations are becoming a daily activity. Dravo Lime plans to take advantage of these transportation changes, all of which may be beneficial to both its plant and its customers.

Jan 10, 1982

By Roger G. Haga, Richard P. Campbell

Introduction Project scheduling . . . . • What is it? • Why is it done? • Who does it? • How is it done? • When is it done? These are some of the questions that will be addressed in this paper. It is intended that by exploring these questions, an understanding of project scheduling, its purpose and benefits can be achieved. The purpose of this article is not to describe in detail "how to schedule", but rather to give an overview of the scheduling function on a project. A successful scheduling effort is dependent upon the people responsible for developing, implementing, and monitoring the schedule, and the tools and procedures that are used. These three elements are integral components of project scheduling. What is it? A schedule is the integration of network relationships, resource constraints and the calendar. The schedule identifies when the activities "will" be done, while the network states when they "must" be done. Networking techniques are the most widely accepted scheduling tool for complex projects. The benefit of the network is the simplicity in illustrating, presenting and analyzing the dependency relationships of a project. The logic network is the foundation of the schedule. When calendar dates are applied to the logic network, it becomes a schedule which provides the basis for evaluation of project status, forecasting the occurrence of events and controlling the project. The sequence of activities that requires the longest time to complete determines the overall duration of the schedule. This longest sequence of activities is called the "critical path". The "critical path method" (CPM) is used to describe this particular schedule network methodology. The two common conventions of CPM networks are the "arrow diagram met hod" (ADM) and the "precedence diagram method" (PIM). There are arguments in favor of each of these two methods, and usually the one that is used is a matter of personal preference, project directive or corporate procedure.

Jan 1, 1986

By Franc Runovc

The service hoisting plant in the mining transportation is an installation serving for the vertical transport of material and persons. An adequate mathematical model is presented for simple evaluation of the project parameters where different plant designs and the ways of transport are take into consideration. The technical and economical optimization procedure is added to the basic mathematical model of the project. This approach enables on one hand the optimization of the reconstruction of the multi-purpose hoisting plants in order to suppress possible bottle necks, while on the other hand it enables the determination of such values of the parameters of the choice and of the operation that the sum of total expenses per a transport unit' becomes the lowest. The optimization procedure is designed in such a way that all numerical data of the optimum hoisting plant are printed out together with the graphical representation of dependencies of the fundamental parameters in broader optimization region.

Jan 1, 1992

By K. A. Natarajan, K. Karthiga Devi

"A biodegradable flocculant was produced during growth of Bacillus megaterium. The major component of the bioflocculant was found to be a polysaccharide composed of some proteins. Fourier transform infrared (FTIR) spectra analysis revealed the presence of carboxyl and hydroxyl groups in the bioflocculant, and thermal characterization by differential scanning calorimetry (DSC) showed the transition and crystalline melting point at 90-105°C. The effects of bioflocculant dosage and pH on the flocculation of mineral suspensions were evaluated. The bioflocculant exhibited good flocculating capability on mineral suspensions and achieved flocculating efficiencies of 90 percent for kaolinite and 85 percent for hematite suspensions at a dosage of only 5 mL/L. The maximum arsenite removal was found to be 90 percent at a bioflocculant dosage of 2 g/L, which is better than traditional chemical flocculants. This study demonstrates that microbial bioflocculants have potential for application in environmental cleanup, such as in the flocculation of mineral fines and in the remediation of solutions that contain toxic heavy metals.IntroductionBioflocculants are biopolymers produced by microorganisms during their growths. The predominant components of a bioflocculant are extracellular polymeric substances such as glycoprotein, protein, cellulose and nucleic acid (Salehizadeh and Shojaosadati, 2001). Bioflocculants have gained much wider attention due to their biodegradability and safety. In recent years, the study of bioflocculants has attracted wide attention. Bioflocculants can be nontoxic, harmless and eco-friendly. Normally, they exhibit different functional properties, serving as stabilizer, dispersant or thickener. Among these properties, flocculation is of major interest. For example, Phormidium sp. strain J-1, isolated from a drainage channel, exhibited excellent flocculation activity for bentonite particles in liquid suspension (Fattom and Shilo, 1984). A protein bioflocculant produced by Rhodococcus erythropolis could efficiently flocculate suspended solids while losing their flocculating activity by enzymatic digestion (Kurane et al., 1994, Takeda et al., 1991). Klebsiella sp. strain S11 screened from activated sludge was unable to flocculate without the addition of calcium chloride (Dermlim et al., 1999)."

Jan 1, 2015

By G. M. Bernard

An overview presentation of the fast-track start up of Cerro Colorado, a new copper heap leach project in Chile's Atacama' desert. A brief explanation 'of location of the property, exploration history, geol-ogy, reserves and development are presented. The overview includes mining, crushing, agglomeration, and the solvent extraction-electrowinning recovery process. Challenges and requirements specific to heap leach systems will be addressed and analyzed. A detailed description will be given of the mobile heap leach conveying and stacking systems used in the building of heaps for on-and off-pad operations.

Jan 1, 1995

By V. Svalbonas

The process of grinding mill quality assurance brings with it associated truths and myths. When the mill quality assurance process took its first great steps forward in the late 1970s and early 1980s, they were in response to the conditions existing, in our industry, at those times. In the late 1990s, we are faced with different conditions, and problems, and need fresh solutions. Yet the system developed for the early 1980s has produced no new approaches for the late 1990s, becoming instead more hardened and entrenched. This lack of development and actual resistance to research is now costing the industry significant amounts of money in late start-ups and useless scrap loss.

Jan 1, 1999

By Felicia F. Peng, Wenguang Wang

The purpose of this research work is to predict the dust concentration distributions of different particle sizes on longwall faces. This Is necessary because the dust sources must be identified before dust control techniques can be recommended and applied correctly. The dust concentration data at longwall faces were determined by using Real-time aerosol monitors (RAM-1) and gravimetric monitors. However, these field data cannot explain the nature or the mechanisms of dust flow phenomenon on longwall face. Therefore, a mathematical model Is developed taking Into account the characteristics of airflow, the natures of dust generation and particles, the mechanisms of dust transport and deposition as well as the multiple dust sources on the longwall faces. In this paper, the identification of respirable dust sources on the longwall faces are determined. The dust particle size distributions In various longwall faces are analyzed and classified. The comparison analyses of field data and model predictions are presented. Specifically, the general trends of dust concentration on the longwall faces obtained at different positions and at various conditions are discussed.

Jan 1, 1991

By H. Jung, J. Kim, Y. Lee, Y. Seo

"Shale gas has become an increasingly important source of natural gas supply in North America and around the world. Horizontal drilling and multi-stage hydraulic fracturing are the two key enabling technologies for the economic development of these shale gas reservoirs. It is believed that gas in shale reservoirs is mainly composed of free gas within fractures and pores and adsorbed gas in organic matter (kerogen). It is generally assumed in the literature that the monolayer Langmuir isotherm describes gas adsorption behavior in shale gas reservoirs. In this work, we have analyzed several experimental measurements of methane adsorption from the Horn River Shale core samples that obey the Langmuir isotherm. INTRODUCTION In nature, gas shales are characterized by extremely small grain size, extremely low permeability on the order of nano-Darcy (10-6 md), small porosity, and high total organic carbon (TOC). Shale can serve as both source and reservoir rock. The amount of gas in place in shale is strongly affected by the TOC, clays, and the adsorption ability of methane on the internal surface of solid (Martin et al., 2010). Since a considerable amount of gas in shale reservoirs is adsorbed, investigation of gas adsorption can provide critical insights into evaluation of well performance and reservoir characterization. Generally, natural gas in shale reservoirs is stored as free gas in both larger mineral pores and natural fractures, as well as adsorbed gas within organic matter (Leahy-Dios et al., 2011). EXPERIMENT METHOD & THEORY Adsorption Experiment Several experiments were carried out on 9 shale core samples obtained in a vertical well drilled within Horn River basin (Figure 1). The CH4 adsorption isotherms were measured for the different depth. In order to measure the amount of adsorbed gas, the high pressure Belsorp-HP equipment applying volumetric method was used. The temperature was kept at 298 K and pressure was increased up to 18 MPa. Approximately 5 g of crushed sample was used for each measurement."

Jan 1, 2016

By Jerry Demchuk, Allan Flemming, Stephan Day

Luscar Ltd. is currently developing open pit mining plans for the Telkwa Coal Project. Most waste rock is predicted to be non-acid generating but a proportion (less than 20%) is potentially acid generating. The waste management plan includes in-pit and ex-pit disposal of blended and till-capped waste rock, segregation and in-pit encapsulation of strongly potentially acid generating materials, and in-pit underwater disposal of coarse and fine tailings. The paper will present the steps used to design the waste management plan including the development of geochemical design criteria using various tests and theoretical and practical knowledge of waste behaviour.

Jan 1, 2000

By J. Y. Hwang, M. L. Jeong, R. C. Greenlund

Various aluminum-smelting by-products from three production sources were received and characterized. The waste materials were tested for compound identification and environmental acceptance. A coarse metallic aluminum recovery test using an Eddy Current separator (ECS) was performed using two different Circuit configurations. White dross performed equally well with either Circuit, while black dross processing shows significant difference on the separation results. It was found that ECS technology was effective for particle sizes down to 6-10 mesh.

Jan 1, 2001

By T. Krumins, L. Zunti, R. Frischmuth

"Titanium and titanium alloys are commonly selected for pressure oxidation autoclave vent piping and pressure control valve components, as well as autoclave internals and other process piping. In the autoclave vent application, titanium ignition risk is controlled by limiting oxygen concentration, and preventing high gas velocity gas impingement on surfaces. Oxygen concentration is dependent on the autoclave pressure and temperature operating conditions and therefore oxygen concentration and the associated titanium ignition risk is dependent on standard operating procedures, process control interlocks and permissive conditions. It is not uncommon for these standard controls to be deficient during atypical operating conditions, or for operations to deviate from the operating procedures, increasing the potential for a titanium ignition incident. Titanium ignition risk caused by elevated oxygen concentration in autoclave vent systems can be reduced with the introduction of an online autoclave overpressure calculation and the configuration of associated interlocks and permissive conditions. INTRODUCTION High temperature pressure oxidation (>190°C) is a well recognized and versatile metallurgical oxidative pre-treatment process commonly used to liberate gold from refractory sulphide ores and concentrates before conventional leaching with cyanide. Titanium and titanium alloys are highly corrosion resistant in pressure oxidation process conditions and are therefore commonly selected as materials of construction for many components including: autoclave internals, agitators, process piping, and components in autoclave vent systems. Operations that anticipate or have experienced aggressive corrosion in the vent system often have little choice in material selection other than the use of titanium (Krag & Henson, 1992). Titanium is not suitable for use with elevated oxygen concentrations and is considered a restricted material because of its high pyrophoricity and combustion propagation properties (Beeson, Smith, Stewart, 2007). Several serious incidents have occurred in which titanium materials have ignited in autoclave applications (Zawierucha, McIllroy, Million, 1995). In autoclave vent applications, titanium ignition risk is reduced by preventing elevated oxygen concentrations, maintaining low gas velocities, and minimizing the potential for gas impingement on surfaces. Oxygen concentration in the autoclave vapour phase and vent system is dependent on the autoclave operating pressure and temperature conditions and therefore titanium ignition prevention controls typically include process interlocks and operating procedures based on the selected nominal design operating conditions. However, it is not uncommon for these controls to be deficient or for operations to deviate from the nominal operating conditions over time, increasing the risk of titanium ignition. The introduction of an online calculation of autoclave overpressure and a maximum target autoclave pressure as well as associated process control interlocks and permissive conditions can alert the autoclave control room operator and prevent an elevated oxygen concentration from developing, and therefore reduce titanium ignition risk in autoclave vent systems."

Jan 1, 2016

By Houston Kempton, David Atkins

Mining in semi-arid climates can produce environmental impacts that will not begin for hundreds of years, but once started, may continue for thousands of years. Pit lakes may eventually exceed toxicity thresholds as metals are evaporatively concentrated, and slow unsaturated flow through acid-generating waste can eventually load several kg-SO4/m2-yr to underlying water tables. U.S. regulations are poorly equipped to respond to delayed and long-term environmental impacts, delaying permits as operators and regulators grapple with uncertainty. Improved uncertainty analysis, additional long-term mitigation options, and explicit regulatory guidance offer solutions to this dilemma.

Jan 1, 2000

By L. Yuan, J. H. Rowland, D. Bahrami, R. Thomas

Blasting is the main method of production in many non-coal underground mining operations and produces multiple toxic gases as a result. The Mine Safety and Health Administration (MSHA) requires mine operators to measure the level of toxic gases in mines as frequently as necessary to ensure they are below regulatory safety limits. The current practice uses portable gas monitors to check the concentrations of toxic gases after a fixed post-blast time. This paper studies the application of a gas monitoring system in the return entry of a limestone mine to determine a safe re-entry time. The National Institute for Occupational Safety and Health (NIOSH) conducted such a monitoring program in a limestone mine from September 2016 through May 2018. NIOSH/PMRD (Pittsburgh Mining Research Division) is endeavoring to develop workplace solutions to improve detection of and reduce the risk of hazardous conditions. This study showed that the use of gas monitoring in the return air can be a useful tool at the mine operator’s disposal to detect and reduce the risk of hazardous conditions and also to reliably estimate the re-entry time.