Search Documents

Excavations in rock are commonly supported with wire mesh, shotcrete, wire mesh and shotcrete in combination, and shotcrete reinforced with various types of fibres. Wire rope lacing and various types of straps are additional forms of support installed over the above types, to cope with severe conditions. These support systems are very important items of ?membrane? rock support. With the recent development of several types of thin sprayed linings, the importance of membrane support is likely to increase in the future. In this paper, a wide range of mechanisms of membrane behaviour and mechanisms of loading of membranes, is described. The concepts of membrane components, which are single membranes that may be used on their own as rock support, and membrane systems, which are combinations of more than one membrane component, are introduced. Different situations have different requirements of membrane support, and differences between civil engineering and mining requirements are highlighted. With the different basic requirements in these two areas, the requirements of rock support are correspondingly different. A thorough understanding of the mechanisms of behaviour of the different types of membranes, and the different mechanisms by which the membranes are loaded, is essential before a selection of appropriate support can be made, before appropriate design methods and calculations can be determined, and before appropriate performance test methods for membranes can be defined. The material in this paper contributes towards the understanding of membrane support behaviour.

Jan 1, 2001

By M. Saghaeian, R. Hejazi, L. Hosseini, M. V. Sheikhzadeh

HPGR equipment has been well proven to be energy-efficient in the first stage of grinding in iron ore beneficiation plants. Numerous advantages of utilising HPGR grinding prior to ball mill grinding, such as reducing the power consumption in a ball mill through generation of micro-cracks, has been thoroughly studied. Less attention has been paid to efficiency of the HPGR circuit rather than the downstream ball mill circuit. In this study the HPGR circuit has been optimised through feed size reduction by crushing, and feed iron content upgrading by dry cobbing. This optimisation leads to better operation of the HPGR, and a smaller product size which is expected to result in a lower wear rate of ball mill liners and balls. It is also expected that the top size of the ball mill balls be reduced. Additionally, by reducing the feed size of HPGR from 30 mm to 15 mm, it is possible to achieve similar K80 of HPGR product in lowered pressure, i.e. 2.5 N.mm-2 instead of 3.5 N.mm-2 which translates to ease of operation. Similarly in a given roll pressure, smaller feed sizes result in higher specific throughput of ~10% which means higher production capacities. The results also reveal that this optimisation increases the concentrate weight recovery by about 10%. It also results in slight increases in the Fe grade of the product iron concentrate. Keywords: HPGR, HPGR circuit optimisation, crushing prior to HPGR, dry cobbing prior to HPGR, ease of operation, concentrate grade optimisation, weight recovery optimisation

Jan 1, 2020

As the world continues to face the turmoil of the economic environment, legislative prerequisites and physical conditions the intervention of technological development is vital for the continuation of the ancient source of revenue: mining. The Palabora underground mining project is a state-of-the-art shaft mining system that will prove to be a benchmark in its field for years to come. An integration of modern technology?both in application and development?has resulted in a shaft system that is intrinsically holistic. Every aspect of the mining and production process has undergone thorough investigation, simulation and innovation to ensure that every component is selected by design and not simply conforming to past practice or trends. The process philosophy includes proven technology such as to promote the lowest operating cost and process time with the highest yield. The underground mining system is in the final stages of commissioning and will shortly be producing a nominal 30 000 tons per day with a predominantly automated system. This paper discusses the complete state-of-art shaft system developed for the Palabora underground mine, and refers particularly to the headgear, the winders, the conveyances and the shaft guide system, as well as the loading system developed specifically for the high performance requirements of the mine.

Jan 1, 2000

By P. J. D. Lloyd

At first I read this paper with interest, which grew to fascination, and ended up with horror. Such reactions to a supposedly scientific contribution are rare, and I believe the coal mining community must be warned in the strongest possible terms against the recommendations that this paper makes. The paper purports to have assessed statistically two sets of data on methane concentrations recorded in the return air from Turkish longwalls. The first set of data, from their Table I, is reproduced in Table I below. The data have been rearranged in classes to indicate the underlying distribution. While there is only limited data (N=33), the distribution looks as if it could be the sum of two normal distributions with means around 0.5 and 0.8, or possibly a log-normal distribution. What is quite clear is that it is nota single normal distribution.

Jan 1, 2004

By M. Akyüzlü

The equilibrium between carbon-saturated Fe-Cr-Si-C alloys and SiO2-CaO-MgO-A2O3-CrO2-FeOy slags was studied under atmospheres of argon and carbon monoxide at temperatures of 1500 and 1600°C. The equilibrium distribution of chromium, silicon, and iron between the slag and the metal phases was determined for different compositions of both phases under different atmospheres and temperatures. It is shown that silicon transfer from the slag to the metal increases with increasing temperature, decreasing carbon monoxide partial pressure, decreasing carbon content of the metal, increasing chromium-to-iron ratio of the metal, increasing silica content of the slag, and decreasing lime-to-alumina ratio of the slag. Some activity calculations were made for the experiments conducted at 1600OC in a carbon monoxide atmosphere. It is also shown that a decrease in the iron content and an increase in the slag basicity decrease the chromium content of the slag. A major proportion of the chromium present in the slag was found to be in the divalent state under the highly reducing conditions prevailing in the experiments. The chromous capacities of these slags were calculated and were found to decrease with increasing basicity.

Jan 1, 1992

By А. V. Aksenov, S. G. Rybkin, А. Y. Senchenko

For gold plants in Russia, it is very complicated and costly to use cyanide leaching for efficient processing of gold refractory ores, where gold is closely associated with sulphide minerals and the significant amount of natural carbonaceous matter present. Oxidative roasting of gold refractory concentrates is a well-known method, making it possible to obtain a high recovery rate of precious metals to a target product. The use of oxidative roasting is limited in general by the expense of capturing and neutralising the harmful components of roasted gas, mainly sulphur (SO2, SO3) and arsenic (As2O3) oxides. This paper addresses testing and development of an optimised technology to process gold refractory gravity and flotation concentrates by means of oxidative roasting which stabilises arsenic as calcium arsenate. The process involves roasting of a gravity or flotation refractory ore concentrate in a mixture with lime and calcium chloride, with a supply of oxygen, and at 600-700°С. During the roasting a carbonaceous matter of the concentrate burns out and sulphide components transform into harmless calcium sulphate (CaSO4) and calcium arsenate (Ca3(AsO4)2), and iron passes into the form of hematite (Fe2O3). After disintegration, the roasting cinder is concentrated on a table to obtain a high-grade gravity concentrate and gravity tailings. The high-grade gravity concentrate is subject to smelting in a mixture with fluxing agents, which results in alloyed gold and slag. The gravity tailings are ground and reported to cyanide leaching. In the case of a flotation concentrate, the roast cinder is ground to minus 30 μm and subject to sorption cyanide leaching. High gold recovery (90-95%) of the target product and environmental safety are typical of the improved technology under consideration. Two national patents were granted for the methods developed to treat refractory concentrates bearing precious metals. Keywords: Gold concentrates, oxidative roasting, cinder, cyanide leaching, smelting, alloyed gold

Jan 1, 2020

By M. Kumral, Y. A. Sari

Underground mining operations tend to have higher operating costs than surface mines. When metal prices decrease, profitability is jeopardized due to the high costs. Therefore, mining management harnesses new practices that increase operational efficiency. One way to manage this challenge is to invest in new mine planning practices. Stope layout optimization as a part of underground mine planning aims to identify a portion of the orebody in the form of production volumes (stopes) to maximize profit under roadway and stope dimension constraints. In this paper we propose a novel approach based on identifying ore-rich areas of the deposit and prioritizing their extraction through an iterative heuristic clustering approach. The proposed approach is compared with and validated by an exact method through a small mining example. The heuristics produced nearly identical results in a very short time. Finally, a case study was carried out using a larger data-set. The cluster-based iterative approach generated nearoptimal stope layouts in a computationally effective manner.

Mar 1, 2021

By E. Y. Baafi, H. Fan, W. Zeng

We present a discrete event simulator, TSJSim (Truck-Shovel JaamSim Simulator), for evaluating the stochastic and dynamic operational variables in a truck-shovel system. TSJSim offers four truck allocation strategies: Fixed truck assignment (FTA), Minimizing shovel production requirement (MSPR), Minimizing truck waiting time (MTWT), and Minimizing truck semi-cycle time (MTSCT) including the genetic algorithm (GA) optimization and the frozen dispatching algorithm (FDA) optimization rules. Multiple decision points along the haul routes for all the trucks close to the decision points were included in the model. The simulation results indicate that the trends associated with production tons and queuing time utilizing the four truck allocation strategies (MSPR, MTWT, FDA, and GA) all demonstrated similar patterns as the fleet size varied. As the system fleet size increased, the system production tons under these strategies at first increased significantly and then remained relatively constant; the queuing time relating to these strategies showed a positive relationship with the system fleet size. The bunching time decreased when the truck allocation strategies were applied in the model. In the simulated truck-shovel network system with multiple traffic intersections, by assigning the trucks at the intersections, both productivity and fleet utilization increased.

Dec 13, 2022

By D. Duncanson, R. J. Davidson

The elution of gold from activated carbon using deionized water by R. J. DAVIDSON, M.Sc., Ph.D. (Rhodes) (Visitor) and D. DUNCANSON, H.N.C., B.Sc. Hons. (Strathclyde) (Visitor) The pretreatment of gold-loaded activated carbon with a relatively strong sodium cyanide solution prior to elution with deionized water at 90 to 125°Chas been shown to have a most beneficial effect on the elution of gold. The findings emphasize the important role played by the calcium cation and the hydroxyl anion in effecting efficient elution of gold. The elution of the relatively unstable complexes of silver and base metals with cyanide was also significantly affected by the ratio of the sodium cyanide to sodium hydroxide in the reagents used in the pretreatment stage. It was demonstrated that the use of 0,5 bed volume of a pretreatment reagent comprising 10 per cent sodium cyanide stabilized with I per cent sodium hydroxide for safety reasons resulted in a virtually 100 per cent recovery of adsorbed gold, silver, and base metals on subsequent elution with deionized water. The elution procedure takes a relatively short time, about 14 hours at 90°C (7 bed volumes) or 3 hours if pressure elution at 125°C (4 to 5 bed volumes) is used. Because the mechanism of elution after pretreatment entails the shifting of a physical rather than a chemical equilibrium, the higher the gold loading on the activated carbon, the more efficient is the elution procedure. When compared with other elution procedures, the proposed method appears to have several economic advantages.

Jan 7, 1977

By V. C. Kelessidis

The interaction between rock and drill bit during drilling has been modeled for many years, but a complete understanding of the phenomena occurring has yet to materialize. Successful models will allow the prediction of rate of penetration in a given environment and optimal selection of drill bit and drilling parameters, thus minimizing exploration costs. In most rock-drilling models the value of the unconfined compressive strength of the rock (UCS) is used in the predictive equations, within the concept of specific energy, and the value of UCS is the percentage of the value of the stress applied on the drilling bit in order for the bit to advance. While the exact percentage depends on the model used and it is not known with certainty, good knowledge of UCS is nevertheless required before any decent prediction can be made on rate of penetration. Determination of UCS, normally done via destructive testing, requires not only the availability of sound rock core samples but also expensive testing and significant time for the test, which frequently are not available for routine drillability predictions. Hence, a multitude of methods and techniques has been proposed for estimating UCS from various indirect and/or non-destructive measurements, or combination of measurements with neural networks, such as point load index, block punch index, unit weight, and apparent porosity, water absorption by weight, sonic velocity, and Schmidt hardness. The many proposed approaches are critically reviewed and the results are compared, and what becomes apparent is that after many years, not only in mining but also in oil-well drilling, accurate indirect determination of UCS is still an elusive goal. An equation to predict UCS from sonic velocity data is suggested based on several data sets reported in the literature. Use of the specific energy equation with UCS or sonic data and utilization of drilling data allows an estimation of the efficiency of energy transfer from the bit to the rock and of the friction coefficient. Analysis of data reported in the literature, both from laboratory and field studies, has shown that this approach is sound and enables the determination of energy transfer efficiencies and friction coefficients, which for the cases studied range between 15 and 30% and 0.15 and 0.30 respectively. Thus, the suggested data analysis approach allows drillers to focus on inefficiencies and optimize drilling practices in future campaigns. Keywords Rock drillability, unconfined compressive strength, prediction.

Jan 1, 2011

By Huanhuan SU, Jianqiang Zhang, Zhongyuan Liu, Junwei Ma

The high-sulfur bauxite in Henan Province was used as raw material. The grinding fineness, pH value and collector dosage on its desulfurization performance, and industrial flotation desulfurization process were studied. The best flotation desulfurization conditions were grinding fineness of 75%, pH of 8.5, and collector of 600 g/t. “One coarse, one cleaning and one sweep” closed-circuit flotation was established as the industrial flotation desulfurization process. After the closed circuit test, the sulfur content of aluminum concentrate with the yield of 93% was 0.23%, and the sulfur removal rate was 83.16%, and the sulfur content of tailings (sulfur concentrate) was 15.09%. Keywords：High-sulfur bauxite under coal mines, flotation, desulfurization

Jan 1, 2020

By D. Bugarin, V. Kecojević, A. Cvjetić, N. Stanić, M. Gomilanović, L. Žujović, T. Stanković

In addition to unfavourable weather and working conditions, incidents and injuries in the mining industry are not uncommon. Factors such as extreme weather conditions, heavy machinery, and unstable terrain make mining a high-risk occupation. To mitigate these risks, there is a growing need for ongoing improvements in employee safety protocols and training programmes. This paper presents a conceptual framework aimed at enhancing the safety training of employees working in surface mining operations. The proposed solution integrates virtual reality and “serious games” as innovative tools to improve safety awareness and preparedness among mine workers. Specifically, a serious game was developed in two versions: a desktop application and a fully immersive virtual reality experience, both using the Unity3D game engine. These applications are designed to simulate real-life mining environments and address various workplace safety scenarios, offering employees an interactive and engaging way to practice their responses to potential hazards. The use of serious games and virtual reality allows for a deeper level of engagement in training, helping workers to retain critical safety information while reducing the risks associated with traditional on-site training methods.

Jul 3, 2026

By Nelson Sánchez

The Los Bronces Development Project (LBDP) was approved in October 2007 by the Anglo American plc Board at a capital cost of some US$1.74B, and is scheduled to be completed by the end of 2010. The project represents a big step forward for the Los Bronces mine since it will increase the treatment rate by 140%, the mining rate by 64% and almost double copper production during the first four years of the project. This economy of scale will also position Los Bronces as a much bigger and efficient mining operation, better prepared to face adverse market scenarios and allowing Anglo to consolidate its position in base metals. The project addressed numerous scope alternatives such as plant capacity vs mine capacity, cut-off grade strategy to maximise value based on the existing flotation and leaching process, cutback strategy, etc. Main infrastructure aspects of the project are as follows: ?Dump area with 2400Mt capacity for waste and low grade material ?Mining equipment: 1 x electric shovel, 12 x 300t trucks, 1 x drill ?Primary crusher: 60? x 89? ?Three new power lines (144MW capacity) ?Grinding plant at 87kt/day nominal capacity (includes a 4.3km tunnel with a regenerative conveyor belt) ?Grinding plant: 1 SAG mill 40? x 25?, 2 ball mills ?Slurry pipeline (52 km from grinding to flotation plant) with five choke stations ?Flotation plant (rougher, cleaning, regrinding circuits and molybdenum flotation). The history of Los Bronces started in 1867 when it was discovered. In 1978 ENAMI (Government company) sold Los Bronces to Exxon for US$112M. The same year a snow avalanche destroyed San Francisco Flotation Plant. In 1979 the plant was rebuilt at 4.9kt/day and from 1979 to 2002 several plant expansions were made up to 54kt/day capacity. In 2002 Anglo acquired Los Bronces for US$1.3B. The 2002 resource and reserve statement showed reserves at 459Mt at 1.02%CuT and resources at 780Mt at 0.80%CuT. The 2007 statement shows reserves at 1,480Mt at 0.67%CuT and resources at 1,644Mt at 0.45%CuT. Defining the size of a plant expansion is the key challenge that any expansionary project faces. The scope of this paper is a general review of the project, describing all the mining techniques that were used to define the best options that maximise value. In this context, a range of plant capacities (from 58 to 230kt/day) combined with a range of mining capacities (from 83 to 166Mt/a) were evaluated in detail, defining for each option a mine plan, Capex and Opex, and cut-off grade strategy for flotation and leaching processes and the associated Net Present Value (NPV) that was used as the selection criteria. The Los Bronces mineral resources potential provides good growth opportunities for the mine beyond LBDP implementation, offering an exciting invitation to continue studying new initiatives that maximise the value of this deposit.

Jan 1, 2008

By D. Ksinsik, R. Boisvert, D. Leblanc

Casting, cooling and crushing/sieving of ferroalloys has followed a well-established pattern in the whole ferroalloys industry for many years. Usually liquid metal or alloys are cast into flat open moulds of various shapes and forms, and after solidification the product is removed from such mould to further cool down to a temperature where subsequent handling steps are feasible. Common to all mechanical product fractioning is the generation of dust and fine size material with lower product value. For almost 10 years, Bécancour Silicon has investigated alternative roads to improve technology and/or reduce or solve problems related to those disadvantages. Since 1995 Bécancour Silicon operates a special silicon granulation plant targeted to product for the chemical treatment/conversion of silicon for silicones production. Prior to the development of the granulation process, various systems had been evaluated, among others the vibrating casting bed, now in operation elsewhere but judged inappropriate because of the tapping volumes to be handled at Bécancour Silicon and other disadvantages. After evaluation of all aspects of heat transfer, radiation, and conductivity in relation to transfer media and within the product, a novel system was designed and built.

Jan 1, 2004

By Y. He

Early research showed that the separation of particles based upon their density was not possible in steadily rising air streams. The terminal velocities of moving spheres are determined by their aerodynamic characteristics. This prevents particle separation by density in standard air classifiers. Passive pulsing air classifiers have accelerated airflow in certain regions, which achieves density-dominant separation. Numerical simulation of airflow within passive pulsing air classifiers was done to estimate airflow patterns near a damper. Analysis of those results shows the significant acceleration of the airflow above the damper. Laboratory trial separations have shown that passive pulsing classifiers are superior to standard air classifiers. Keywords: pulsing airflow, passive, simulation of airflow models, acceleration effect, density

Jan 1, 2005

By A. M. Milev

A simulated rockburst was conducted underground at Kopanang Mine, previously called Vaal Reefs No. 9 Shaft. The rockburst was simulated by means of a large blast detonated in solid rock close to a crosscut sidewall. The simulated rockburst involved the design of the seismic source, seismic observations in the near and far field, high-speed video filming, a study of rock mass conditions such as fractures, joints, rock strength etc. Knowledge of the site conditions before and after the simulated rockburst was also gained. Some of the important findings are listed below: ?Two areas of damage were identified on the blasting wall: (i) an area of high-intensity damage in which ground velocities of 3.3 m/s were recorded by an accelerometer, which was subsequently ejected in a block of rock, (ii) an area of low-intensity damage where ground velocities of 1.6 m/s were recorded by an accelerometer which remained on the tunnel wall. ?High-speed filming revealed rock fragments being ejected from the wall at velocities in the range of 0.6 m/s to 2.5 m/s. The measurements were taken in the area of low-intensity damage. As planned, no gas pressure was directly involved in damaging the wall of the tunnel. ?The attenuation of peak particle velocities for the main blast in the near field (6 m to 30 m), as a function of distance R, was found to be proportional to R-1.7. ?The simulated rockburst was recorded as a local magnitude ML= 1.3 by the Klerksdorp regional seismic network. ?Peak particle velocities from nearby blasting, recorded on the tunnel wall after the simulated rockburst, were about six times greater then peak particle velocities recorded from the same source area before the simulated rockburst.

Jan 1, 2001

By R. Dekkers, J. Plessers

The feasibility of using hydrogen to obtain clean steels is investigated. High hydrogen contents are generally considered as detrimental due to the risk of flakes, bubbles and breakouts during casting. Hydrogen can nonetheless be removed by degassing of the steel. The results of industrial campaigns, where total oxygen content and hydrogen content were monitored, are presented. High resolution microscopy of inclusions and laboratory experiments on the rate of inclusion removal by CaO-Al2O3 slags at different partial hydrogen have been carried out. So far, evidence that hydrogen may influence inclusions or the steel cleanliness is not clear. Keywords: hydrogen, cleanliness, inclusions.

Jan 1, 2004

By John V. Simmons, Peter J. Simpson

Excavated slopes in open pit coal mines are designed to be as steep as possible consistent with stability and safety requirements. Slope failures occur for many reasons, including oversteepening. This paper is concerned with slope design and excavation experience in the Bowen Basin coalfields of central Queensland (Figure 1), [ ]

Jan 1, 2006

By J. -C. Trickett

The high-resolution three-dimensional (3-D) seismic reflection data acquired for Impala Platinum between 1998 and 2002 in the western Bushveld Igneous Complex form an integral part of Impala?s mine planning and development programme. These data are of sufficiently high quality to provide unprecedented 3-D models of the geological structure of the Merensky Reef and UG2 Chromitite Reef, from which the mine deduces the size, geometry and distribution of mineable blocks. Conversely, the seismic data details zones of un-mineable ground caused by structural disturbances in the form of potholes, fault zones and pegmatoid intrusions. Furthermore, variations in dip and strike are well imaged, allowing the mine planners to optimize the mine design and layout. Current interpretation work is focused on enhancing the accuracy of these geological models even further through the analysis of ?seismic trace attributes.? Preliminary testing on the Impala Platinum 3-D seismic volume has shown that attribute analysis has the potential to illuminate a number of geological reef disturbances that are otherwise ?invisible? in the original seismic time volume. Potential areas of improvement include inter alia: ?Improved definition of major fault zones ?Improved definition of zones of reef depression (?slumping?) ?Identification of reef terracing and/or reverse dip. Keywords: 3-D reflection seismics; Impala Platinum Ltd; seismic attribute analysis; seismic micro technology (SMT); rock solid attributes; dip-azimuth; instantaneous phase and similarity.

Jan 1, 2005

By H. Schunnesson, H. Fredriksson, D. Johansson, E. Söderström, S. Manzoor, A. Gustafson, M. Danielsson

Fragmentation analysis is an essential part of the optimization process in any mining operation. The costs of loading, hauling, and crushing the rock are strongly influenced by the size distribution of the blasted rock. Several direct and indirect methods are used to analyse or predict fragmentation, but none is entirely applicable to fragmentation assessment in sublevel caving mines, mainly because of the limitations imposed by the underground environment and the lack of all the required data to adequately describe the rock mass. Over the past few years, measurement while drilling (MWD) data has emerged as a potential tool to provide more information about the in-situ rock mass. This research investigated if MWD can be used to predict rock fragmentation in sublevel caving. The MWD data obtained from a sublevel caving mine in northern Sweden were used to find the relationship between rock fragmentation and the nature of the rock mass. The loading operation of the mine was filmed for more than 12 months to capture images of loaded load-haul-dump (LHD) buckets. The blasted material in those buckets was classified into four categories based on the median particle size (X50). The results showed a stronger correlation for fine and medium fragmented material with rock type (MWD data) than coarser material. The paper presents a model for prediction of fragmentation, which concludes that it is possible to use MWD data for fragmentation prediction.

Mar 2, 2022