Search Documents

To determine the characteristics of a mineral deposit, the usual practice is to take samples, analyse the properties of those samples and infer the characteristics of the deposit from these properties. This analysis can be done using statistical methods. In the present work we are concerned with two types of statistical approaches, classical statistics and spatial statistics. If one uses classical statistics to represent the properties of the sample values, the assumption is made that the values are realizations of a random variable. The relative positions of the samples are ignored, and it is assumed that all sample values in the mineral deposit have an equal probability of being selected. The likely presence of trends, zones of enrichment, or pay shoots in the mineralization, is ignored. The fact that two samples taken close to each other are more likely to have similar values than if taken far apart is also not taken into consideration. In contrast, spatial statistics will be used if one chooses to consider that the sample values are realizations of random functions. On this hypothesis, the value of a sample is a function of its position in the mineralization of the deposit, and the relative position of the samples is taken into consideration. The similarity between sample values is quantified as a function of the distance between samples and this relationship represents the foundation of spatial statistics. There are few situations where classical statistics can be used. The assumption that all sample values in the mineral deposit have an equal likelihood of being represented will be satisfied only if the sample values are randomly distributed, or if the sample positions are random. Sample values are in fact never randomly distributed within a mineral deposit. Further- more, geologists usually avoid taking samples at random (random sampling), as it is correctly accepted that samples located on a regular grid, or approximately on a regular grid, give more information than randomly located samples. In practice, classical statistics should be used only in the early stages of exploration, when the number of samples available is relatively small and the distances between samples are large. In these circumstances, and whenever the information available is not sufficient to permit the use of spatial statistics, application of the methods described in this chapter is justified.

Jan 1, 1978

By Y. G. Che, M. Brown, R. L. Gandhi, M. D. Watson

Slurry pipelines have proven to be an economical method of mineral concentrate transport over long distances. Some of these pipelines are internally lined with high-density polyethylene (HDPE) to avoid internal corrosion. HDPE is an inert and extremely smooth material, and it was believed hat scale deposits would not form on it. However, there have been instances of scaling on HDPE lined pipes. Scale problems have also occurred on bare steel pipes. In this paper experience with scale problems in some of these pipelines will be summarized. Alternatives available for control of scale problems will be discussed, and a success story for the control of scale problems in the 300 km long Century zinc and lead slurry pipeline will be presented.

Jan 1, 2007

By V. Matou?vek

The paper addresses pipe flows of aqueous medium-sand slurries at velocities lower than the deposition-limit velocity. Laboratory test results including measurements of particle concentration distributions are used in order to describe a flow with a (pseudo-) linear concentration gradient above a stationary bed. Particle dispersion within the flow is evaluated and a stratification-ratio equation is formulated, estimating a portion of contact load in the flow. The formula is incorporated in the proposed predictive model for the hydraulic gradient for a medium-sand flow above a stationary bed.

Jan 1, 2007

By G. C. Howell, H. A. D. Kirsten

The mining-induced effects around narrow tabular stopes have traditionally been evaluated in terms of elastic continuum analyses. An understanding of the phenomenological behaviour of the rock surrounding deep-level gold mines has accordingly been developed on the basis of such analyses. However, elastic analyses do not afford reliable representations of the behaviour of rock in which failure may occur on discontinuities. This paper describes investigations that show how the stress and stiffness characteristics of a rockmass are affected under such circumstances for representative ranges of values for the relevant parameters (depth, span, support stiffness, field stress ratio, and discontinuity strength). These investigations afford a substantially different understanding of the mechanical behaviour of rock that is subject to failure. Instead of forming an arch across the abutments, the rock in the hangingwall bears directly across the stope onto the footwall and, instead of being subjected to tension, the nether hangingwall is clamped in compression in the horizontal direction.

Jan 1, 1993

The structural design of a pavement relates to the ability of the road to carry the imposed loads without the need for excessive maintenance or rehabilitation. Current techniques for the structural design of haulage roads are empirical and based primarily on the previous experience of personnel assigned to pavement design, both in terms of the strength of the structure and the quality of the wearing course material. This has the potential for unwarranted expenditure on too thick a structure or, conversely, premature deformation leading to the need for excessive expenditure on maintenance. Furthermore, the effect of larger haulage vehicles on the structural performance of a pavement cannot be predicted. Thus, there is a need to develop a portable and practical method of structural design. This paper presents an overview of structural design methods for mine haulage roads and, through an analysis and quantification of the structural performance of existing pavements, recommends the mechanistic design procedure, together with a revised structural design and associated limiting design criteria. It is concluded that the application of the mechanistic method to a design project can reduce the costs of haulage roads construction and accrue additional benefit in terms of reduced operating and maintenance costs.

Jan 1, 1996

By I. D. Wood

Deposition of gold-bearing deposits in the Witwatersrand Basin was controlled by hydraulic processes. These resulted in the formation of independent sedimentological facies areas having different statistics and semivariograms. Consequently, when there are indications that data are a mixture of statistical populations, it is important to decompose them into statistical subpopulations and analyse these independently. However, in the case of actual mining, physical position and extent of sub- populations are important and, as a consequence, any decomposition of data must take space into account if it is to be of use. An algorithm for the spatial decomposition of data into its sub-populations is described and is applied to real data taken from the Witwatersrand. Two distinct areas with completely different geostatistical parameters were revealed.

Jan 1, 1987

By V. P. Kolosyuk, A. M. Bryukhanov

Occurrences of hazardous events (explosions of methane or coal dust, fires, outbursts) have been investigated and presented as a flow of events in time. It has been shown that flows of hazardous events in a long time span are homogeneous, stationary and no-after effect flows and can be considered as stationary Poisson flows. A flow of CH4/coal dust explosions that had happened for the last 27 years in Ukraine was analyzed. The explosions have been statistically processed. Practicability of agreement of statistical and theoretical data on mathematical expectation and mean square deviation of time interval between explosion and the explosion intensity has been stated. Probability of an emergency event in time is expressed through an exponential function, while mathematical expectation of an accident and mean square deviation of time interval between successive explosions are in inverse proportion to the accident intensity. Accident probability for practical purposes can be determined as a product of accident intensity by calculated time interval.

Jan 1, 2003

By E. A. Brinkmann

A kinetic model framework for single particle kinetics in combined diffusion and adsorption processes is presented. The framework applies to the general case in which both diffusion and the adsorption reaction play important roles in determining the overall rate in processes where the migrating species can both adsorb and accumulate. The technique, which should be applicable to a wide range of reaction mechanisms, consists of an iterative integration procedure for the coupled diffusion and reaction equations. The case of a reversible linear adsorption reaction rate is developed. In order to verify the technique as a legitimate method of model development, an analytical solution for the identical case is derived and compared to the numerical solution. Excellent agreement exists between the two solutions.

Jan 1, 1987

The refractoriness of the gold in many of the pyritic ores from the eastern Transvaal is due mainly to the association between the gold and the sulphides, but it can be due to the presence of graphltlc carbonaceous material, which complicates the recovery of the gold by virtue of its adsorption activity. In an examination of the roasting characteristics of three flotation concentrates from the Barberton area, It was found that the gold in the concentrates occurred mostly in two forms: in very fine gold particles distributed within the arsenopyrite, and in a slightly coarser form loosely associated with the pyrite. Direct cyanidation of the concentrates gave gold extractions of from 16 to 30 per cent. After the concentrates had been roasted at temperatures of 650 to 700°C for 20 minutes with rabbling, the extractions varied from 86 to over 90 per cent. Examination of the residues after cyanidation indicated that gold was present in the porous calcines or in the calcined sulphide product. This observation, together with porosity measurements, suggests that physical encapsulation of the gold particles is the main reason for the refractory behaviour of the gold in the calcines.

Jan 1, 1988

By M. Gershon

During the exploration phase of mine development, drilling location is in the hands of the geologist, and drilling is spread over the entire domain of the property or deposit boundary. During the mine planning and production phases, however, the mining engineer also needs to use the information obtained from the drilling program. Thus it is important that he/she have some input into the selection of the drillhole locations. Usually, when exploitation will center on one portion of the property for the immediate future, the mine engineer will want to have more of the drilling performed in this area. In the early stages, the purpose of the drilling was to make a decision concerning whether or not to develop a mine. Once the decision is made to proceed with this development, the mine engineer needs to know, with as much confidence as possible, the estimate of the ore grade at each location where mining will occur. This paper addresses the problem of drillhole location for the needs of the mining engineer. The goal is to compare a variety of approaches to drillhole location with a new approach developed by the author. This approach is based on the theory of geostatistics, with the estimation variance used as the quantitative measure of the confidence attained. The goal of the algorithm is to select those locations that minimize the estimation variance subject to constraints on the number of drillholes and the total cost of the drilling program. The kriging equations are used as another set of constraints. The resulting nonlinear optimization model is expressed in terms of binary (0 - 1) decision variables leading to a solution by the branch-and-bound procedure. The algorithm has been applied at a number of operating properties, and practical results and suggestions for implementation are provided.

Jan 1, 1987

By M. Berjak, D. M. Hawlins, R. B. MacGillivray

SYNOPSIS The paper describes a method of producing iso line plans using a mathematical technique for interpolating between boreholes, and its computer application. The iso line plans are used for assessing the value parameters of an ore body. The computer programme also produces means and standard deviations to supplement these iso line plans. The mathematical techniques tested for the production of a satisfactory fit of the data were the polynomial, Fourier and moving average technique. The iso line plans are used for assessing the quality of the ore and other salient features such as depth to the floor of the ore body at different points, with a view to deciding how best the ore may be mined. The plans are plotted by the computer to any scale required. INTRODUCTION To assess the economic exploitability of an ore body many tedious and repetitive calculations must be carried out. Observations of borehole or development samples have to be processed yielding measures of ore reserve and quality in each sampled area, and also measures of the worth of the ore body as a whole and of variation in quality from section to section of the ore body. The observations made on the ore (which we shall term 'value parameters') may embrace a variety of characteristics of the ore. Obvious value parameters are those directly related to the economics of mining, viz. assay values, ore body thickness and depth below surface. Other value parameters however may be almost as important. In the case of coal for example a purchasing contract may specify limits of acceptability on other value parameters such as calorific value, ash content or the percentage of volatile matter. In this case, a detailed study of these value parameters will also be crucial. This detailed study must include an assessment, not only of the body as a whole, but also the regional variation in value of the parameter. An obvious and satisfactory way of displaying this variation is by drawing iso lines of constant value parameter on a map of the ore body and supplementing this with the means and standard deviations of the value parameters taken over all boreholes. Such plans, considered together, show up the zones of significance. The relatively stereotyped nature of the operations involved in this process makes it amenable to computer solution. In order to produce iso line plans on the computer we require some mathematical formula for producing a 'valuation surface'-a mathematical

By D. Duncanson, R. J. Davidson, C. G. S. Schmidt, G. A. Brown, J. D. Taylor, N. W. Hanf

The development of a cyanidation route for the treatment of gold-plant gravity concentrates is described. This work was carried out as a natural consequence of earlier improvements to the recovery of gold in the gravity sections of existing gold plants. Concern about the environmental aspects of the conventional amalgamation process was further motivation in the development of an alternative procedure. It was found that the partial pressure of oxygen in solution was the most critical reactionrate determining factor. The rate of gold dissolution was shown to be controlled by the reaction rate below approximately 25°C and by diffusion above that temperature. Thus, the efficiency of pulp agitation and oxygen partial pressure permitted a high degree of control over the rate of gold dissolution. The use of oxygen rather than air significantly increased the dissolution rate of both gold and silver. The solubilities of sodium, calcium, and potassium aurocyanide complexes under simulated reaction conditions were studied, and it was established that the values for the sodium and calcium complexes were limited, requiring the use of lower pulp densities and higher reaction temperatures for the treatment of very high-grade concentrates. The presence of excessive amounts of tramp iron in such concentrates of up to 25 per cent by mass was found to result in poor gold dissolution owing to the cementation of gold under certain reaction conditions. The maintenance of high oxygen partial pressures, together with high cyanide concentrations, high pH levels, and the presence of calcium in the system, all aided in passivating the tramp iron. Copper, gold, and iron were shown to be the main cyanide-consuming elements. Optimum gold dissolution was obtained in a closed bench-scale reactor incorporating a flotation-machine type of agitator for effective pulp agitation and oxygenation, the oxygen being recirculated. The reactor was designed to operate under a very small positive pressure. After reaction times of 2 to 6 hours at temperatures in the region of 30°C, both the gold and the silver dissolution averaged 99,S per cent. In the case of very high-grade concentrates, it was shown that gold could be floated in the same reactor by drawing off the flotation concentrate through a port in the reactor. A flotation recovery of 87,4 per cent of the gold in 3,9 per cent by mass was obtained. The recovery of osmiridium from cyanide-leach residues and the electrowinning of gold from the pregnant liquors were also considered as processing aspects in the treatment of gold-plant belt concentrates. Final table tailings with a gold concentration of 10to 12 gft were obtained. The results of the investigation strongly suggested that an alternative cyanidation route for the treatment of gold-plant concentrates was technically feasible, provided the system included effective agitation and oxygenation. In the case of lower-grade concentrates, cyanidation followed by the electrowinning of gold appears to be the simplest route, while, for high-grade concentrates, flotation and smelting of the concentrate followed by cyanidation of the flotation tailings are suggested. The use of oxygen rather than air for sparging the pulp would depend largely on the grade of material to be treated. A preliminary comparison of the costs related to the amalgamation and cyanidation processes for the recovery of gold from such concentrates indicated very similar capital and operating costs. It was concluded that other considerations, e.g. toxicity, safety, and lower labour requirements, were more important than such small cost differences. Furthermore, the 'opening' of the gold-plant gravity circuit, which would be made possible by a cyanidation route, would further reduce the operating costs because of the subsequent decrease in the tonnage to be treated.

Jan 1, 1978

By L. Marais, S. Denoon-Stevens, J. Cloete

"Historically, mining companies worldwide provided housing and developed towns to accommodate their employees. At the end of the 1980s this approach became less prevalent and attempts were made to mitigate the effects of mine development and mine closure on communities living near the mines. Permanent settlement in mining towns urgently needed to be minimized. Since the advent of democracy, South African policy has moved in the opposite direction, shifting the emphasis to creating integrated communities and encouraging home ownership. Despite this policy shift, however, mines continue to influence local housing conditions. One direct outcome has been the development of informal settlements. We surveyed 260 informal settlement households in Postmasburg, a small and remotely located town in the Northern Cape Province of South Africa. We found that because they employ contract workers and thus arouse expectations of employment, the mines here contribute extensively to the development of informal settlements. But local factors also contribute, and the functional role of informal settlements as a form of housing that supports mobility should not be underestimated. We also found that both municipal and mining company policies for informal settlements were inadequate. Finally, we found that low-income informal settlers not associated with mine employment suffered the highest levels of social disruption.IntroductionA mine generates demand for labour, which in turn generates demand for housing. When settlements spring up near a mine this often means poor housing conditions. In South Africa in the 1960s and 1970s mining companies invested heavily in company towns or mining settlements, but they have become increasingly hesitant to do so, for three reasons. First, declining resource prices in the mid-1980s and the 1990s compelled them to focus on core business interests and reduce the costs of peripheral activities such as housing (Bryceson and MacKinnon, 2013); second, at the turn of the 20th century they were often accused of taking over the role of local government (IIED, 2002) and consequently became hesitant to invest in developing mining towns; and third, changing labour regimes also curbed their investment in such towns (Haslam McKenzie, 2010). Increasingly, the companies began to endorse block-roster shifts, and outsourcing also became more common in the early 1990s. Block-roster shifts in Australia (together with improved technology) have meant that miners do not need to settle near the mines but can fly in and fly out and have their urban houses as their stable homes. This has had serious negative implications for housing in remote towns in Australia, particularly worker camps, large-scale renting out of available accommodation, and ‘hot-bedding’."

Oct 1, 2018

By C. Holck, J. Yarmuch, J. Read

"Steepening of slopes provides the means to reduce waste extraction and increase ore recovery in open pit mines; however, it may also adversely affect safety by posing a higher risk of slope failure. The implementation of slope monitoring programmes is recommended to manage this risk inherent in steeper slopes. In this paper, the design and evaluation of monitoring campaigns to measure subsurface deformation and groundwater pore pressure in open pit mines is presented. The monitoring programmes were applied to a theoretical case of an open pit mine designed using DeepMine software (BOAMine SpA, 2015). Mine plans were developed based on the initial base case scenario with monitoring programmes considered for four types of monitoring instrumentation: two established technologies, in-place inclinometers (IPIs) and vibrating wire piezometers (VWPs); one emerging technology, the ShapeAccelArray (SAA); and a novel technology under development, the Enhanced Networked Smart Markers (ENSMs). Technical and economic appraisals of the monitoring programmes and sensitivity analysis of the developed mine plans showed that using ENSMs spaced every 4 m had the lowest cost per unit of data gathered. IntroductionSeveral open pit mines have already exceeded their design life and, as they become deeper and reach depths over 1000 m, they face higher rock stress levels and tensile deformations (Stacey and Xianbin, 2004; Stacey et al., 2003). The more complex the conditions in modern open pit mines, the more difficult it is to achieve long-lasting, stable pit slopes and to meet the mine’s economic needs: maximize financial returns, minimize risks to operational safety, achieve optimal ore recovery, and minimize waste extraction (Stacey, 2009). Steepening of slopes provides the means to reduce waste extraction and increase ore recovery (Stacey, 2009; Calderon and Tapia, 2006; Bye and Bell, 2001; Jefferies, Lorig, and Alvarez, 2008); however, it may adversely affect operational safety, as steeper slopes are less stable than shallow slopes (Steffen et al., 2008; Mphathiwa and Cawood, 2014)."

Nov 1, 2018

By Willie Hefer

Contents ?Purpose ?Introduction ?Deviation of bias results ?Operational correctness ?Maintenance and Costs ?Conclusion ?Acknowledgements

Jan 1, 2005

By A. H. Swart, M. F. Handley

Unplanned stope panel collapses occur on most near-surface and shallow mines in South Africa. Although these incidents often occur during blasting, they pose a major threat to the safety of underground workers and the economic extraction of orebodies. Most stope panel collapses occur due to excessive panel lengths that are not designed according to a systematic design procedure or methodology. Instead, panel lengths are often dictated by the equipment in use and by previous experience under similar conditions. Hence, a rock engineering design methodology for the design of stable stope panels between pillars is of vital importance for optimum safety and production in shallow mining operations. Using the proposed design methodology described in this paper, rock mechanics practitioners and mine planners should be able to identify and quantify the critical factors influencing the stability of stope panels. The critical factors should then be used as input to the design of stable stope panels that will provide the necessary safe environment for underground personnel working in stopes. The proposed design methodology is an iterative process, which includes aspects such as rock mass characterization, estimation of rock mass properties, identification of potential failure modes, consideration of appropriate stability analyses and other elements of the rock engineering design process. This process continues after implementation. During monitoring, new data should be included in the database and the design process repeated on a regular basis. Design approaches included in the proposed design methodology include empirical methods such as different rock mass classification methods, analytical methods such as elastic and Voussoir beam analyses, kinematic analyses, probabilistic analyses, and numerical analyses. Keywords: stability, stope panels, design methodology, hard rock mines, shallow mining operations

Jan 1, 2004

By R. Singh, A. K. Dhawan, M. Dixit, H. Dev

ABSTRACT: The modulus of deformation of rock mass is an important engineering parameter required for the design of foundation of hydraulic structure and to study the interaction of rock mass and the structure at the foundation support. Different equipment and techniques are used to arrive at the design modulus value. Since any error in the estimation of modulus values results in multiplication of its effects in the analysis, it is necessary to know about the reliability of testing equipment and procedures. In the present study modulus values obtained by different in-situ equipment at different project sites have been compared. KURZFASSUNG: Der Verformungsmodul von der Felsenmasse ist technisch ein wichtiger Parameter, den man zur Konstuktion des Grunds fuer die Hydro – Tektonik, benoetigt um auch die gegenseitige Beeinflussung der Felsenmasse und der Tektonik am Traggrund zu betrachten. Verschiedene Geraete und Methoden werden angewandt, um den Ausfuehrungsmodul -Wert zu erreichen. Es ist erforderlich, die Zuverlaessigkeit der Pruefeinrichtung sowie des Verfahrens zu kennen, da irgend ein Fehler in der Abschaetzung von Modulwerten in der Analyse zu einer Vervielfachung ihrer Einwirkung fuehrt. In der vorligenden Arbeit werden die Modulwerte gewonnen aus unterschiedlichen Einrichtungen an Ort und Stelle and verschiedenen Projekt -Stellen mit einander verglichen. SOMMAIRE: Le module de deformation d’une roche est un parametre important pour la conception et realisation des ouvrages hydrauliques ainsi que pour etudier l’interaction de la roche et de la structure d’appuis de base. De divers equipments et techniques sont employes pour determiner la valeur de ce module de conception. Puisque l’effet d’une erreur d’evaluation du module devient multiplie dans l’analyse, il est necessaire de savoir la fiabilite des equipments et des methods qu’on ulilise. Dans cette etude, on a compare les valeurs des modules obtenues en employant les equipments in-situ aux sites differents de projets.

Jan 1, 2003

The 86th Annual General Meeting of the South African Institute of Mining and Metallurgy was held in Kelvin House, Johannesburg, on Wednesday, 17th August, 1983. Professor A. N. Brown (President) was in the chair, and declared the meeting open at 16h05. This account of the proceedings includes only those matters that are not reported under the heading `Annual report and accounts' elsewhere in this issue.

Jan 1, 1983

By D. Ackerman, S. Cole, G. Langefeld, I. Parker

The removal of gravel from the seabed using a hydraulic mining tool is a complex multi-phase problem that cannot be analysed using traditional continuum based simulation techniques. One potential approach is to simulate the behaviours of the solid phase via the discrete element method and the liquid phase via finite volume based computational fluid dynamics. The interaction between the phases is accounted for by Eulerian coupling. The feasibility of using the combined computational fluid dynamics-discrete element method to simulate gravel entrainment from an idealized seabed is evaluated. The simulation results are validated using experimental data. It is concluded that while the current approach appears feasible, further work needs to be done to improve the accuracy of the simulation and to evaluate the approach?s ability to model more complex behaviours.

Jan 1, 2007

By C. Ringas, F. P. A. Robinson

Various theories proposed to account for microbial corrosion are reviewed as a background to a better understanding of this type of corrosion in iron-based alloys. Experimental evidence is presented to show that even stainless-steel alloys are prone to microbial attack by sulphate-reducing bacteria. The corrosive attack by the bacteria is due primarily to the hydrogen sulphide that is produced as part of their metabolic processes.

Jan 1, 1987