Search Documents

By L. S. Linda, P. G. H Pistorius

Ferritic stainless steel is utilized to fabricate automotive exhaust systems using a ferritic weld metal. Ductility of the weld metal is higher if its microstructure contains a significant proportion of equiaxed grains. The formation of equiaxed (rather than columnar) grains is favoured by a higher titanium weld metal content. In this study, the Ti content of ferritic stainless steel weld metal was changed by using Tifree (Type 436) and Ti-containing (441) ferritic stainless steel as base metals. The metal-cored welding consumable contained 0.4% Ti. Gas–tungsten arc welding and gas–metal arc welding processes were compared. The weld metal Ti content ranged from zero to 0.5% Ti, as determined from scanning electron microscopy supplemented by inductively coupled plasma optical emission spectroscopy. Cross-sections of the weld beads were subjected to point counting (to estimate the fraction of equiaxed grains) and image analysis (to estimate the average grain size). Point counting proved to be more reliable. The fraction of equiaxed grains was sensitive to the Ti content, but not to the welding process. Below 0.4% Ti, the fraction of equiaxed grains gradually increased with an increase in the weld metal Ti content; above 0.4% Ti, the fraction of equiaxed grains rapidly increased with increasing Ti content. The transition in behaviour at 0.4% Ti corresponded to a Ti content at which Ti-rich precipitates became stable at the estimated liquidus temperature of the weld metal.

Jul 2, 2022

The Barrick North Mara Mine and the Advanced Systems Group at SGS Minerals collaborated on the implementation of a grinding expert system for the control and optimisation of a single semi autogenous (SAG) mill. Over the last 5 years, grinding expert control has gained wide acceptance by mineral processors. In this paper, two key factors for success are highlighted: the adaptability of the software tools and the interaction with site personnel. Created with SGS?s MET expert console (MEC) toolkit, and running on Gensym?s G2 real time inference software, the North Mara expert logic has been set up to keep a steady and on spec leaching feed slurry while striving to maximize throughput. Leach feed stability was achieved by standardizing operating practices across shifts; a result of successful collaboration with site personnel in developing a consistent control strategy. The strategy maintains the SAG load and power draw in an optimised range by manipulating SAG feed rates and inlet water flow. The project life-cycle was slightly longer than average due to site specific constraints. One of these was the high turnover rate of site?s workforce during the project, coupled with the availability of key staff on site due to the fly in fly out work roster. These constraints called for different, and innovative ways of project commissioning and hand-over. This paper describes details of the control solution, its implementation as well as results and conclusions.

Jan 1, 2009

By H. Jiang, W. Wang, Y. Zhao, J. Qiao, C. Duan

DEM simulations were used in this research to study the screening process of a novel variable amplitude equal thickness vibration screen (VAETVS). The response regularity of mass distribution and granular moving velocity at the different screen panels to feed rate was investigated and the predictive model for the unit area processing load was proposed. The influence of aperture size, the size variance, and the opening ratio on the mass passing-distribution and overall screening performance, respectively, were revealed. The results showed that the response model of the unit area load Ф to the feed rate Q can be concluded as Ф∝0.324×Q. The moving velocity of particles also showed a positive relevance to the feed rate, besides which the passing rate of fine-grained material at the feed end was negatively related to the aperture size, while the case was reversed in the feed end. The increase of aperture variance AV enhanced the passing ability of small particles at the feed end,and reduced the misplaced ratio of the large particles at the discharge end. A better screening efficiency can be obtained when the average aperture size of the entire sieve is 7.5 mm, with the aperture variance of 1 mm between the adjacent panels. When the combination of the opening ratio is 35-35-40, a better screening effect can be achieved. Keywords: Equal thickness screening, DEM, particulate velocity, mass distribution regulation

Jan 1, 2020

By Z. Nzimande

The Constitution of the Republic of South Africa advocates the importance of sustainable economic development and justifiable environmental consciousness by business. The government needs to ensure that every citizen of the Republic has access to an environment that is protected, pollution free, and sustainable by enacting certain regulations. However, there are more than 5 700 derelict and unrehabilitated mines of all types in South Africa. Former asbestos operations were among the first to be targeted for clean-up under the programme instituted by the Department of Mineral Resources (DMR), owing to the proven direct impact of asbestos pollution on health. This paper seeks to investigate the challenges faced by the coal sector as far as mine rehabilitation and closure is concerned. For the purpose of this paper rehabilitation is defined as per the Chamber of Mines Rehabilitation Guidelines publication, which defines rehabilitation as putting the land impacted by mining activities back to a sustainable and usable condition. Some of the current rehabilitation challenges are technical skills (know-how), leadership focus, poor planning, cost saving initiatives, and the government's lack of capacity to enforcement rehabilitation requirements. It is imperative that mining companies identify rehabilitation as a critical strategic pillar that directly influences license to operate. The case study evidence indicates that relevant policies, appointment of accountable people, sufficient leadership support, and the correct choice of rehabilitation equipment can assist to improve the rehabilitation and land management challenge.

Jan 1, 2012

By E. -U. Reuther

To improve the climatic environment underground the German coal mining industry has installed refrigerators with a capacity of 300 MW cooling power. One third of this total is accounted for by central refrigeration plants with more than 5 MW capacity. The central refrigeration comprises three stages: mechanical cooling, transport and distribution of chilled water via pipelines and exchange of heat in the air coolers. Of these three stages only the mechanical generation of chilled water has been resolved satisfactorily. Transport (including distribution) and exchange require further technical research. The Mining Institute of the Aachen University of Technology has done extensive studies on this subject, concentrating on controlling the flow of chilled water according to demand in the mine. Additionally, the favourable exchange in the air coolers is taken into account. The studies are based on a model mine which simulates the conditions in deep coal mines in Germany. The simulation program represents firstly the condition of the mine air at the location of the air being cooled, then the heat exchange in the air cooler itself, and finally the transport of the chilled water from the central refrigerator to the consumer. The program also reproduces the seasonal and operational changes in conditions of mine air as well as different air cooler designs. A regulated distribution of chilled water is also suggested. Finally, estimations of costs can be made as an aid for further planning.

Jan 1, 1987

By G. Blight

As part of an investigation of possible water-saving measures at Anglo American Platinum's Mogalakwena Mine in Limpopo, South Africa, a study was made of conditions on the wet beaches of two adjacent tailings dams, each serving a separate plant on the mine. For one of the dams, a special catamaran was designed and constructed to enable the full length of wet beaches to be accessed and sampled immediately after a layer of tailings had been deposited. For the other dam, the wet beach was accessed using conveyor belting and scaffold planks. The length of the beaches was 400 m on the first dam, and 200 m on the second, and each was sampled at 50 m intervals. The parameters reported in this paper, for both beaches, are: > Water content profiles along each beach from the surface to as deep as 2.5 m, at times ranging from 12 hours to 6 weeks from the end of deposition > Particle size distributions at the surface, down the full length of the beaches > Measurements of feed relative density, tonnage and volume, decant and drain flow volumes, as well as rainfall and evaporation for both dams. The surface water contents shortly after deposition have been used to establish the relative density of the settled, decanted tailings and its variation down the beach. This data, combined with the decant and drainage flows, is used to establish the calculated and actual water recoveries from both dams.

Jan 1, 2012

By J. R. L. Read, A. N. Ogden

This paper describes mining industry funded research that is being undertaken to address the critical gaps and uncertainties in our knowledge so that we can develop new approaches and create more effective ways for predicting the reliability of rock slopes in large open pit mines. It is envisaged that this research will not only lead to more effective pit slope design but further reduce the potential for unforseen geotechnical risks by enabling the geotechnician to communicate the risks more effectively with management and to optimise site specific control measures. To achieve this, several research tasks are in hand. The first is to accurately represent the structured rock mass with a 3D computer model (Siromodel) that creates polyhedral blocks from structural distribution data characterised by position, orientation and persistence. Siromodel is being coupled with particle flow and other numerical codes to evaluate how the structured rock mass deforms in the stress environment of an open pit and how a candidate failure surface may propagate through the dilating rock mass along the path of the least shear and/or tension resistance. A beta version of the Siromodel software has been distributed to 20 Sponsor mine sites for technical evaluation. The end state is to develop methods of analysis that characterise the reliability of a described candidate surface, and the probability of the candidate surface propagating to failure, recognising that the rock mass strength may well be defined in a different way than before.

Jan 1, 2006

By D. Skelton

The Renard kimberlite cluster is located in the Monts Otish region of Quebec, Canada. A Canadian National Instrument (NI) 43-101 compliant resource statement for the Renard kimberlites 2, 3, 4 and 9 and the Lynx kimberlite dyke was first issued in 2008 followed by a Preliminary Economic Assessment and the development of a conceptual mine plan. Following a successful drill program in 2009 that greatly expanded the amount of kimberlite in Renard 2, a revised resource statement was issued in December 2009 comprising 23 million carats of Indicated Mineral Resources and 13 million carats of Inferred Mineral Resources, a threefold increase on the previous estimate. The project is currently the focus of a second Preliminary Economic Assessment and it is expected that a full feasibility and permitting program will commence in 2010 leading to the creation of Quebec's first diamond mine by 2013.

Jan 1, 2010

By L. Gutierrez, R. Yepsena

Enargite in porphyry copper deposits is an important mineral as it displays good floatability under the presence of the collectors usually used in the flotation of copper sulfides. As a result, copper concentrates grades are reduced. As scarcity of water resources is a problem relevant to Chilean mining, the use of seawater is a feasible solution. The behaviour of copper sulfides and molybdenite in the process of flotation in seawater was previously studied but not for enargite. The objective of this research is to study the behaviour of the enargite in different conditions of electrochemical potential during the process of flotation using seawater. The study was carried through micro-flotation tests using pure samples of enargite, at Eh values ranging from -300 to 500 mV(SHE), both in seawater and aqueous solutions containing calcium and magnesium. The results show that at pH 10.5 in seawater, the enargite and chalcopyrite recoveries are reduced throughout the whole range of Eh studied. At pH 9 in seawater, enargite and chalcopyrite are depressed under reducing and slightly oxidising conditions. The recovery of both minerals drastically decreases at Eh values lower than -100 mV and greater than 400 mV. The behaviour of enargite in seawater flotation differs from that observed in conventional water, since in the latter case the recovery of enargite decreases at higher potentials close to 500 mV. Keywords: Enargite, flotation, seawater, redox potential

Jan 1, 2020

By M. G. Wimberger

The Merensky Reef zone, as developed on Impala Platinum?s Rustenburg Operations, displays a gradational mineralized zone, with grades decreasing from the Merensky Pegmatoid Unit into the footwall and hanging wall. A system of identifying a manageable method of defining the mining cut is introduced, termed the grade profile attenuation cut-off grade. Although horizontal grade selectivity is not applied in the mining of the Merensky Reef zone, low extraction of the orebody, due to manageable and non-manageable factors, can contribute to a reduction in revenue, even losses, due to fixed cost contributions in the mining and beneficiation of the ore. A model is proposed that integrates all variables affecting the revenue of the mining operation, including the grade profile attenuation cut-off grade, the extraction factors, commodity prices and exchange rates, utilizing numerical simulation techniques in a PC-based environment. A breakeven extraction factor for a specific cut-off grade is delivered for a range of market conditions. The breakeven extraction factor is a useful guide when designing mining layouts in structurally complex and low metal content areas. Incorporating distribution functions for individual commodity prices and exchange rates into the model provides mineral resource managers with a risk profile for individual mining areas. Shaft areas have varying grade profiles and each area should have individual models run, to prevent generalizations being made about acceptable risk levels on mining areas.

Jan 1, 2004

By J. D. Flint

A description is given of the extraction of pillars in a seam of coal which normally varies in thickness from 10 feet to 14 feet using conventional trackless mechanised units. By using the pocket and fender method of pillar extraction, the high capital cost of hydraulic supports is eliminated, and a volumetric extraction of 85% to 90% of the seam of coal is possible. This method of mining opens up the possibility of extracting vast tonnages of coal which hitherto would have been left in situ as pillars. The major benefits likely to accrue from this technique are seen as follows: 1. Greater volumetric extraction of the seam; 2. Longer panel life with less frequent transferring of sections; 3. Preservation of our natural resources. The authors deal with the history of this development at Springfield Colliery, discuss the present results and outline the future trends in the light of current experience.

By A. J. Van Rensburg, N. B. Strydom, C. H. Van Graan

The design, construction, and use of a practical ice-jacket for miners by N. B. STRYDOM, Ph.D. (Illinois) (Fellow), D. MITCHELL, Ph.D. (Rand) (Member), A. J. VAN RENSBURG, M.Sc (Poteh) (Visitor), and C. H. VAN GRAAN, M.Sc (Pretoria) (Visitor) Microclimate suits have been shown to be very effective in decreasing physiological strain in hot, wet environments, thus enabling men to work without risk in areas that would normally carry a high risk of heat stroke. In this paper, some design considerations in the development of the frozen jacket are described. Water complied with most of the desirable properties required of a coolant material for use In a microclimate suit. The Human Sciences Laboratory has developed a jacket in which ice is used as the coolant and which is designed according to the most acceptable anthropometrical characteristics. The jacket consists of an inner poncho-type waistcoat containing 28 water compartments. Over this is worn an insulating jacket, which minimizes warming of the coolant by the environment. Suitable refrigeration units have been developed to freeze the jackets underground. Laboratory tests have shown that these jackets are effective for about 2,5 hours, Irrespective of the wet-bulb environment, when men are working at a moderate rate. Jackets should, however, be used only in environments in which the wet-bulb temperature is in the range of 32,S0 to 35,S °C.

Jan 9, 1974

By T. Ramamurthy

ABSTRACT : Rock mass classifications RMR, Q and GSI do not suggest decreasing modulus ratio with the decrease in the quality of rock. These have been linked to joint factor, Jf , for better prediction. An engineering classification is suggested based on strength and modulus applicable to both intact and jointed rocks. ZUSAMMENFASSUNG : Fels Masse Klassifizierungen RMR, schlägt Q und GSI daß das Abnehmen von modulus Verhältnis mit der Abnahme in der Qualität des Felsen nicht vor. Diese sind zu gemeinschaftlichem Faktor, Jf, für bessere Voraussage verknüpft worden. Eine technische Klassifizierung wird auf der Basis auf Kraft und modulus vorgeschlagen die zutreffend sind zu beiden unversehrten und jointed Felsen. RESUME: RMR de classifications de masse de Rocher, Q et GSI ne suggèrent pas la proportion de modulus décroissante avec la diminution dans la qualité de rocher. Ceux-ci ont été reliés au facteur de jointure, Jf, pour mieux la prédiction. Une classification construisant est suggérée basé sur la force et modulus applicables intacts et les rochers de jointed.

Jan 1, 2003

Numbering of the Journal Because computer and library authorities prefer journal subscriptions to be based on the calendar year, and because the present numbering system of the Journal of the South African Institute of Mining and Metallurgy does not conform with the calendar year, it has been decided to change the numbering system of the Journal.

Jan 1, 1979

By D. Noort, M. Dawborn, D. O. del Castillo

This paper was originally presented at the North American/9th US Ventilation Symposium, June 2002, Kingston, Ontario, Canada. Reprinted with permission of the publishers, A.A. Balkema Publishers, Rotterdam, Netherlands. This paper is a study of the ventilation, cooling and refrigeration system design of the Mindola copper mine in Zambia. The challenges that were addressed varied from the restrictions imposed by an ageing infrastructure to the requirement for increasing the annual production rate, coupled to the introduction of a higher level of mechanization while maintaining acceptable conditions and limiting total ownership costs. A description of how the ventilation, refrigeration and cooling systems were modelled in order to obtain the projected heat loads associated with two different mining methods over the life of the project. The methodology included a number of iterations to optimise the design and include aspects such as the expected inrush of hot fissure water, the operation of diesel machinery at depths in excess of 1500m below surface, developing a cost-efficient cooling strategy and selection of the refrigeration machinery to meet the requirements imposed by the cooling strategy. This paper demonstrates the successful implementation of an integrated design approach.

Jan 1, 2005

By S. K. Gilman, V. E. Hugo

A common problem encountered in the mineral sands industry is that the mineralogical measurements used in defining the resource are not readily converted to metallurgical recoveries, which are used to predict the quantity of the final products. The problem stems from the different objectives of the exploration and metallurgical assessment programmes, and is often compounded by the use of different laboratory techniques and mineral definitions. Common mistakes include the misapplication of routine analysis, incorrect interpretation of mineral recovery, the confusion of mineral recovery with product yield and inconsistent definition of the same mineral. Experience has shown that unless these potential mistakes are identified, the measurement techniques used during exploration and metallurgical assessment are not compatible, often resulting in large errors in the prediction of mineral production. There are no easy solutions to the problem, as there is no universal assay technique which can cost effectively characterize all the mineral sands resources. The recommended course of action will therefore require several iterations to optimize the assay technique to suit the resource. Fundamental to the success of the measurement technique is the understanding of the mineralogy, its behaviour during mineral processing and the quality requirements for the final products.

Jan 1, 2003

By R. C. M. Minnitt, W. Dr. Assibey-Bonsu, F. A. Camisani-Calzolari

Born in Bothaville (OFS) on the 26th August 1919, Daniel G. Krige grew up in Krugersdorp on the West Rand. Hematriculated from Monument High School in Krugersdorpin 1934 at the age of 15 and graduated with a B.Sc. (Eng.)degree in mining engineering from the University of the Witwatersrand at the end of 1938 (age 19). In 1938 he joined Anglo Transvaal where he worked on a number of gold mines until 1943, gaining a wide range of valuable practical experience in surveying, sampling and ore valuation. He then joined the Government Mining Engineer’s Department where he worked for 8 years during which time he participated in the uranium negotiations with the British and American authorities and designed the uranium pricing formula for the contracts which led to the establishment of South Africa's profitable uranium industry in the early 1950s. During the same period he began his pioneering work in the application of mathematical statistics to the valuation of new gold mines using a limited number of boreholes and of ore reserves for existing mines. His early papers in the application of mathematical statistics, some republished in French, created world-wide interest that led to the development of the science and concepts that surround the spatial evaluation of mineral resources and reserves known as geostatistics. This technique has contributed to improved ore evaluation techniques as well as the reduction of the financial risks associated with investment in mining enterprises. Furthermore, it led to the recognition of his contributions to the evaluations of mineral deposits through the coining of the term ‘kriging’ that is used to describe a spatial mineral evaluation process known and practised in international mining circles. He continued his work in geostatistics throughout his career as Group Financial Engineer of the Anglovaal Group until his retirement in1981 and afterwards for ten years as Professor of Mineral Economics at the Witwatersrand University. He is still active as a consultant and is a registered Professional Engineer. He has published some 90 technical papers both locally and overseas, some in Russia, and has lectured and participated in international congresses in many countries. His contributions were recognized by the Witwatersrand University through the award of the D.Sc. (Eng.) degree in1963, by three honorary degrees (from the universities of Pretoria, UNISA and Moscow State Mining University), by many awards from the South African Institute of Mining and Metallurgy, the International Association for Mathematical Geology, Die Suid Afrikaanse Akademie vir Wetenskap en Kuns, the SME of the American Institute of Mining Engineers, the International APCOM Council in1999, the University of Antofagasta in Chile, and by the South African President (Order for Meritorious Service, Class 1, Gold). He has served on various Government committees, notably that for State Aid for gold mines (1967/8) and designed the State Aid formula which enabled many mines to survive a period of low gold prices; also various taxation committees, and the mining mission to Iran in 1974. He is a fellow and/or honorary life member of various technical societies locally and overseas, including the Royal Society of South Africa. During the period in the Government service he also handled several of the post-war lease applications in the Free State and Klerksdorp goldfields. The fact that decisions on new gold mines of critical importance to the State and the economy as a whole, were being taken on a limited number of drillholes without any scientific analysis of the risks of failure, stimulated him to start basic research into ore evaluation. His approach was based on the application of Mathematical Statistics to these problems, an approach of which very little was known world-wide at that stage but which had already been initiated in South Africa by Sichel via the lognormal frequency distribution model. In Krige's 1951 paper published in the Journal of the Chemical, Metallurgical and Mining Society of South Africa he covered the statistical explanation of the conditional biases in ore block valuations and stimulated the use by several gold mines of regression corrections for routine ore reserve valuations, a technique which, in effect, was the first use on an elementary basis of what is now known as kriging. His 1952 paper introduced, inter alia the basic geostatistical concepts of ‘support’, ‘spatial structure’,’ selective mining units’ and ‘grade-tonnage curves’. His 1951 paper was based on his M.Sc. (Eng.) thesis submitted in the Department of Mining Engineering to the University of the Witwatersrand, and expounded his pioneering work in geostatistics in more detail. His early research papers that had stimulated interest in several mining circles overseas, were republished in French in1955, resulting in a major research effort by French mining engineers in this field. This, in turn, led to the establishment of the now world-renowned French school of ore evaluation in Fontainebleau, Le Centre de Geostatistique de l’École des Mines de Paris. As the Group’s Financial Engineer at the Anglovaal Head Office until his retirement in 1981, he was responsible for

Jan 1, 2003

The 8th Annual University of Cape Town (UCT)/ University of Stelenbosch (US) Minerals Processing Symposium was held at the Van Riebeeck Hotel in Gordon's Bay on 3rd August, 1990, under the auspices of the Western Cape Branch of The South African Institute of Mining and Metallurgy. The primary object of this meeting was to give research students at UCT and US the opportunity to present their work to a critical audience from industry, and to obtain feedback regarding the research needs of the minerals industry. Although the emphasis of these symposia is on work in progress at US and UCT, they also create an excellent opportunity for informal discussion between academics and metallurgists in industry. The first symposium in this series was held in 1982 at US, while the symposium in 1989 was replaced by the International Colloquium on Developments in Froth Flotation, also held in Gordon's Bay.

Jan 1, 1990

The South African Institute of Mining and Metallurgy mourns the passing of one of its most distinguished sons. Professor J. de V. Lambrechts died at Franschoek on 30th January, 1988, at the age of 76 years after a long illness. Mintek Application Reports A new series of Mintek reports made its appearance in 1987. These are Application Reports, which present an overall perspective of each of Mintek's technical thrusts to ensure that the existing expertise can continue to be readily accessed. The successful development of an industrial process for the recovery of platinum-group metals from the UG-2 Reef. Application Report no. 1. 1987. 16 pp. The development and implementation of a computer control strategy for conventional milling circuits. Application Report no. 2, 1987. 15 pp. The development of an integrated carbon-in-pulp process for South African conditions. Application Report no. 3. 1987. 17 pp.

Jan 1, 1988

By G. Peinaar

Superhardening is a new development by which a substantial increase in hardenability above the normal can be achieved in Iow-alloy steels. This paper concerns the reversible temper-embrittlement behaviour of steels with a superhardenability characteristic. Steels of type BS 530A40 with manganese modifications varying from 0,72 to 1,27 per cent in the superhardenable and conventional condition were compared. It was concluded that superhardenability in itself does not affect the susceptibility of a particular steel to temper embrittlement. However, an increase in manganese content, which was intended to increase the base hardenability of the steel, caused serious deterioration of the temper-embrittlement properties. As the use of manganese, chromium, and nickel to increase base hardenability results in an increase in susceptibility to temper embrittlement, it is suggested that this effect should be countered by the addition of 0,2 to 0,3 per cent molybdenum.

Jan 1, 1984