Search Documents

By S. Purushotham, Y. R. Murthy, M. Narasimha, S. K. Tripathy, M. Kumar

Spiral concentrators are gravity-based separators widely used to beneficiate coal, heavy minerals and beach sand. It consists of a helicoid trough that spirals downward in the helical configuration around an axial column. The particle segregation takes place based on size and density under the influence of gravity as the particles spiral down within the thin water layer. In the last century, most design modifications of this equipment were based on trial and error based lab-scale experimentations and empirical approach. The use of Computational Fluid Dynamics (CFD) has gained interest in the past two decades to understand the underlying flow physics in the spiral concentrators. In this paper, we used CFD to model the fluid flow and investigate the particle segregation inside a conventional LD9 spiral concentrator. Firstly, the Volume of Fluid model was used to resolve the liquid-air interface. The liquid depth and flow field predictions for varying flowrates were validated against the experimental literature data. One-way coupled VOF-LPT model was then used to describe the particle dynamics in the spiral flow field assuming dilute particulate flow. Moderate dense particulate flow (20 vol.%) was then modelled using the Algebraic Slip Mixture (ASM) model. Four particle-phases representing particles of different sizes of dual-density were simulated, and the component particle segregation was analysed. Keywords: Spiral concentrator, two-phase flow, multiphase, discrete phase model, ASM model

Jan 1, 2020

By A. Çelik

Wheel loaders are widely used in many sectors due to their mobility, operational flexibility, and low costs. The literature is mainly focused on improving the hydraulic, mechanical, and electronic subsystems of these machines in terms of efficiency or developing strategies for controlling these systems. In this study, the effects of the loader operator and different working conditions on the loading performance were investigated. The study was carried out at the Can Lignite Enterprise (CLI), which is a major coal producer in Turkey. In the study, which lasted approximately four months, a total of 808 measurements were performed to investigate seven different scenarios. The effect of a single parameter on loading performance was investigated in the first six scenarios. The results showed that the biggest impact on loading performance was caused by the operator's experience with 63.4%. On the other hand, the worst and most ideal working conditions determined from the first six scenarios were tested in the seventh scenario. It was tested as a script. The test results showed that the loading performance was 285.5% more effective under the most ideal operating conditions compared to the worst operating conditions. In addition, in the study, the loading performances of five loaders with four different capacities were examined in terms of energy efficiency and it was determined that the Kawasaki 115 work machine, which has a higher model and lower engine operating hours, was more advantageous. In the study, various suggestions were developed in parallel with the research results. The most prominent and easiest to implement of these suggestions is related to the selection of the loader operator.

Nov 27, 2024

By E. J. Magri, D. M. Hawkins

This paper deals with an experimental programme carried out with a gold analyser in the period June to September 1979 at Loraine Gold Mines. The results were found to be reproducible, with no overall or conditional bias when the measurements were compared with those obtained from chip samples. The standard error of estimation of a 3 m reef exposure, which was the sampling interval, can be reduced by a factor of 2,5 if the complete stretch is scanned, rather than the taking of one chip sample in its centre. Complete statistical and computational procedures were developed for the fitting of the normal-Iognormal model to observed analyser data and for the determination of the most likely gold grade for a particular analyser measurement. (This corection procedure is necessary since a significant number of negative analyser measurements can be observed.) Panel averages of uncorrected scans showed a small conditional bias relative to those of corrected scans. However, uncorrected panel averages can be used for on-the-spot decisions regarding whole panels. For standard calculations of ore reserves, use should be made of corrected scans. Under reasonable assumptions, the use of the detector in the selective mining of low-grade narrow reefs such as the Basal Reef at Loraine Gold Mines, when compared with the conventional chip-sampling method, can result in a saving of as high as R40 million in present-money terms over the life of a project. The difference could be even larger in a highly variable reef like the B Reef at Loraine Gold Mines.

Jan 1, 1987

By P. Lenegan, R. Masethe, R. I. L. Ferreira

Underground mining in high rock-stress environments can induce unanticipated dynamic rockmass deformation, posing a serious risk to the workforce. Data collected by seismic networks are imperative for the design-as-you-mine process. Often an inappropriate assessment of the seismic hazard is done when unnecessary data are included in analytical techniques, particularly short-term time frames. Depending on the methodology or application of data analysis and interpretation, some of the information may not be relevant and even detract from the objective. By using the spatial event clusters associated with active workplaces to define the shape and size of the polygons for data selection for subsequent analysis, a problematic subjective component can be eliminated. The mining of tabular reefs in South Africa, be they gold- or platinum group metals, is very extensive, and underground workplaces are often widespread. Production stoppages are very costly, especially for marginal mines, so there is just cause not to evacuate an entire operation’s workforce following the occurrence of a large mining-induced seismic event. A rationale based on the damaging peak particle velocities (PPV) of the past seismicity can exclude the unaffected underground personnel and allow a quick orderly withdrawal where required. Micro-deformation may precede rockbursting, which can occur on-shift close to the workface. A mine-wide array of geophones suitable for the accurate location and analysis of seismicity may not be able to detect these higher-frequency emissions. Inexpensive but fit-for-purpose accelerometers, providing real-time, continuous measurement of acoustic rockmass deformation near the workplace, integrated through underground and surface communications networks, are shown to record ‘rock-talk’, clearly distinguishable from the instrument background noise, which can be in the order of hours leading up to an imminent damaging seismic event.

Jan 12, 2025

By S. Annavarapu

"Fragment size distributions play an important part in the design and planning of block cave mining operations. Though several methods have been proposed for estimating fragment size distributions in advance of mining, the calibration of these estimating procedures to field measurements has been a challenge. The Block Size Estimator (BSE) program was developed for providing an assessment of primary fragmentation expected in a block cave mine using drill-core piece length data and joint characteristics from the exploration and geotechnical evaluation programmes. In order to validate the results from the BSE program, the drill-core piece length data and the joint characteristics in different rock types from the DOZ block cave mine in Indonesia were used to help generate fragment size distributions in different areas of the mine. The predicted fragment size distributions were compared with the fragmentation observed at the drawpoints during operation of the mine.This paper presents the details of the validation of the fragment size estimates by the BSE program using fragment size distribution data from the drawpoints at the extraction level at the DOZ block cave mine, and the challenges encountered in developing reasonable correlations between the estimated and measured fragment size distributions. IntroductionThe assessment of fragmentation is an important aspect of the design and planning of the block cave mining method, and forms an integral part of the design of the excavations at the extraction level and the selection of material handling systems for transporting the ore to the processing stations. Secondary blasting requirements can also be estimated based on the fragment size distributions developed for the block cave (Laubscher, 1994).Several methods of estimating fragment size distributions in block cave mines have been developed based on joint set parameters estimated from structural data from oriented core drilling campaigns and mapping of available excavations and outcrops. The BCF program (Esterhuizen, 1999) estimates the fragmentation using a combination of empirical, analytical, and rational methods to model the behaviour of materials during the primary and secondary fragmentation processes. The program JKFrag uses advanced tessellation of joint traces to create rock blocks and then generate fragment size distributions (Brown, 2002). Nickson, Coulson and Hussey (2000) presented the details of processing of the geotechnical data from the Mont Porphyre project, including an assessment of block sizes from the data collected on the core logging sheet. The distance between natural fractures was used to create distributions of block lengths, and a distribution of potential block sizes was estimated assuming that the blocks had equal dimensions in all directions. The results agreed closely with the results of the BCF program. Hadjigeorgiou, Grennon, and Nickson (2002) demonstrated the use of oriented borehole data to provide characteristic block size distributions for a mining project using a software package called Stereoblock, which generates a three-dimensional joint network for a given volume and calculates the volumes of blocks created by the intersections of these joints, simulated as circular planes. The distributions of joint orientation and joint spacing generated from statistical analysis of the oriented core data are used for the creation of the Stereoblock model. The diameter of the circular planes representing the joints is determined based on the mean and standard deviation of the joint trace length obtained from scan-line mapping."

May 1, 2019

By M. Nicolle

The Tati Activox® Project will be the first full-scale implementation of the patented Activox® process (The Tati Activox® project was deferred in 2008. Please refer to the Norilsk Nickel press issue on the topic for more info). The process was developed by Norilsk Process Technology and has been tested on Tati mine sulphide concentrates in laboratory, pilot and demonstration plant scales and demonstrated its viability. There are inherent risks to the final scale-up of the process from the demo plant and one of them will be investigated in this paper. Compartment 1 is designed to leach approximately 77% of the total nickel leached. For this reason agitation requirements in the first compartment of the autoclave are reviewed. An attempt is made to minimize the process and mechanical risks associated in achieving oxygen mass transfer into the slurry solution. The agitator powers for oxygen mass transfer are calculated using empirical correlations and compared to demonstration plant testwork. The resulting gassed power per unit volume (P/V) is higher than most commercial autoclaves and raises uncertainty on the viability of using such high unit power inputs. Additionally, there is concern about the ability of the autoclave shell to withstand and support the higher loading of large agitators. An alternative solution to designing for the increased P/V is assessed in which the number of compartments within the autoclave is reduced from 5 to 4 by removing the compartment wall separating compartments 1 and 2. This results in an enlarged first compartment containing 3 agitators instead of 2. Therefore the compartment 1 oxygen demand is supplied through 3 agitators, which lowers the P/V per agitator. The reduction in the number of autoclave compartments raises the potential for short-circuiting the mean flow pattern by slurry particles. Short-circuiting and low velocity zones could result in a lower recovery of metal and localized hot spots, respectively. A computational fluid dynamic (CFD) analysis was conducted to quantify these concerns and also to evaluate further design considerations. The results indicate that the proposed design change to 4 compartments affects short-circuiting. The impact of increased short-circuiting on the overall autoclave recoveries is not quantified, however; it is expected to be negligible based on testwork done in the Tati Demonstration Plant and similar modifications made to another operating autoclave. The CFD analysis also suggests that there will be no low velocity zones within the compartment.

Jan 1, 2009

By M. Z. Emad, Y. Majeed, G. Rehman

Massive deposits of rock salt are mined in the Salt Range area of Pakistan. The main export products of rock salt include salt lamps, blocks, and tiles, while local consumption includes the chemical industry and domestic use. The profitable production of salt for value addition depends on the quality, size, and shape of the block. Salt processing for value addition is easier when very few cracks are present in the blocks. The current salt mining practice involves drilling and blasting, which introduces undesired fractures in the material. This paper focuses on the extraction of rock salt blocks by applying conventional cuboidshaped block mining methods used in quarries. The techniques include wedges and feathers, expansion chemicals, and blasting with low-yield explosives. Experimental work involved both laboratory-scale and in-situ field testing. Laboratory experiments assisted with the determination of splitting force, loaddeformation curves, and other rock mechanics parameters. Regression analysis proposes a relationship for the estimation of radial strain from the load in the case of the wedges and feathers method. The splitting force obtained from the laboratory tests was used to confirm the accuracy of the already published empirical relationship. The results of the laboratory as well as in-situ tests showed that the wedges and feathers technique is the most suitable method for mining rock salt blocks of the desired size, shape, while minimizing cracking.

Mar 2, 2022

By C. Birch

"The purpose of this study was to establish the impact of discount rates on cut-off grades for narrow tabular gold deposits as characterized by the goldfields of the Witwatersrand Basin in South Africa. There are various methods available for determining the cut-off grade, from simple breakeven calculations to sophisticated software packages that consider a variety of inputs to optimize the cut-off grade. For this study a simple financial model was created in Microsoft Excel® that links the ore flow, block listing, and the cash flow. This allows the cut-off grade to be optimized considering how the cost of capital and chosen discount rate affect the cash flow.The discounted cash flow (DCF) and resultant net present value (NPV) are a widely used valuation method for production properties according to the South African Code for the Reporting of Mineral Asset Valuation (SAMVAL Code). The financial model in this study utilizes the Solver function, as well as simple Microsoft Excel spreadsheet formulae to optimize the NPV. Solver was chosen as it is a standard feature in Excel and thus no additional software costs are incurred beyond the basic Microsoft Office suite. For the purpose of this study, just narrow tabular gold deposits of the Witwatersrand Basin were considered. An example of a typical ore block listing, as well as the costing figures, was obtained from an operating gold mine. The results obtained from the study financial model were compared to the current cut-off grades obtained from the mine using their proprietary optimizer program, and were found to be comparable. The methodology utilized for this study thus appears valid.The cut-off grade was optimized considering the cash flow, which includes the variable mineral resource royalty tax, the variable gold income tax, as well as the discount rate. By comparing the resultant NPVs using discount rates of zero, 9%, and 12%, the impact of the discount rate on cut-off grades, resultant life of mine, and average mining grades (AMG) could be compared for the example ore block listing. The South African Code for Reporting of Exploration Results, Mineral Resources and Mineral Reserves (SAMREC Code) does not require operations to state if a discount rate was considered in determining mineable reserves. Mining companies approach the question of applying discount rates in determining their cut-off grades, and thus mine planning strategy, in different ways. Due to the negative impact that optimizing purely on NPV has on the life of mine, some choose to optimize only on profit. Other companies have reverted to utilizing pay limits as their primary grade planning strategy. The calculated cut-off grade is then considered to be another planning indicator rather than a hard determination of mineable reserves."

Jan 1, 2016

The Western Cape Branch of the SAIMM recently held a one-day colloquium on the use of artificial intelligence (AI) in process engineering in the I.S. Gericke conference room at the University of Stellenbosch

Jan 1, 1992

By D. Mesa, J. Karvonenb, A. López, P. R. Brito-Parada, R. Grau, D. Davoise

The froth zone in flotation cells plays an important role in determining metallurgical performance. This is even more critical as cell sizes increase, since larger bursting surface areas can easily result in poor froth transport and even stagnant froth zones, which are detrimental to recovery. Generating additional overflowing lip length by adding internal launders and reducing surface area (while also directing the froth to the overflow) by adding crowders are well established design strategies to enhance froth mobility. However, comparative experimental studies of froth zone design modifications at industrial scale are scarce and often lack detailed froth characterisation. In this work, we present the results of two experimental campaigns that were carried out at Atalaya’s Riotinto concentrator in order to determine the effect of a new froth zone design on the flotation performance of a TankCell® e300 cell that operates as the first cell of the rougher bank. These campaigns provided a unique opportunity to assess froth phase phenomena and metallurgical performance before and after changes in design. The original cell design had an internal peripherical launder and a froth cone, while the new concentrate launder technology adds a centre launder and an adjustable froth crowder to the existing launder design. The new concentrate launder arrangement reduces significantly the froth area as well as the froth transport requirements, aiming to improve froth recovery and, consequently, enhance flotation performance, allowing copper recoveries in the TankCell® e300 cell to increase dramatically. In addition, radial profiles of froth height and froth velocity at the surface were determined, which provide valuable insight into the effect of design changes on froth stability and mobility. Keywords: Flotation performance, enhanced recovery, launder, crowder, froth stability

Jan 1, 2020

By Q. Fu, Q. Wang, L. G. Wen, M. X. Jia, J. J. Zhao, J. W. Zhou

The BGRIMM process mineralogy analyser (BPMA) is a new automated mineralogy software platform developed in China. This system consists of the BPMA software platform, controlling a combination of commercially available scanning electron microscopy (SEM) and energy dispersive Xray spectrometry (EDS). The BPMA software controls SEM and EDS through their application programming interfaces, to form an auto-SEM and EDS system that automatically acquires BSE images and X-ray spectra, respectively, and classifies minerals by spectrum-matching. After automated measurement and mineral identification, various quantitative process mineralogical data (e.g., mineral composition, mineral abundance, mineral liberation and intergrowth relationships, mineral associations, particle and grain sizes, particle density distributions, calculated assay, elemental deportments, mineral grade recovery and elemental grade recovery, etc.) would be calculated quickly, accurately and automatically. The BPMA could be used for ore characterisation as a new advanced automated mineralogy technology. Keywords: BSE image; X-ray spectrum; automated mineral identification; quantitative mineralogical investigation; automated mineralogy

Jan 1, 2020

By J. van der Walt, W. Spiteri

Flyrock remains a significant threat to the health and safety of mine employees and integrity of infrastructure, as well as to the safety of the neighbouring communities and their property. This investigation was motivated by the general lack of fundamental research and mathematically quantifiable data in the literature regarding the relationship between blast design parameters and their impact on flyrock. The focus was to develop a concept that can be used to mathematically quantify the trajectory of flyrock resulting from a blast, which can be used for future research. The ultimate goal for this technique, once it has been fully developed, is to: ➤ Enable mining operations to generate a database with accurate historical flyrock measurements resulting from their blasting operations ➤ Allow research teams to conduct scientific investigations into flyrock and the impact of various blast design parameters ➤ Generate point-cloud data to visualize blasts and flyrock in a virtual reality environment for training and education purposes. This paper summarizes a conceptual technique and preliminary fieldwork that was carried out to determine the technique’s feasibility and motivate further development. The results show conclusively that a modified photogrammetric technique is capable of capturing flyrock data for further processing and analysis. The data acquisition procedure can, at this point, be used to meet the first aim of the project, namely to gather a field database of historical flyrock generation. Further development of the technique is ongoing and it is envisioned that the scientific-based technique will provide a method whereby future flyrock studies will be comparable and that assumptions will be limited.

Apr 5, 2023

By J. P. Gouvea, W. Geel

Resin bolting in South Africa has been developed and refined in underground coal mines (i.e., soft rock) since the late 1940s. The extension of resin bolting to hard rock mines started in 2003 and has required significant adaptations, challenging the status quo from both a supplier and applicator perspective. As far as resin bolting is concerned, the most affected aspect in coal mining and hard rock mining environments, is the rock drills or machinery used for installation. Hard rock mines mostly use hand-held airlegs with limited thrust, low torque, and rotation speed, relative to coal mine mechanised bolters. Resin bolt development for hard rock mines was, and still is today, predominantly focussed on compensating for the ‘shortfalls’ of using hand-held airlegs. At face value, hydro-powered rock drills, which are more powerful than traditional handheld equipment, provided hard rock mines with a means to attain more consistent and reliable resin bolt installations. This paper assesses the quality and performance of hydro-powered resin bolting at an intermediate to deep level platinum mine in South Africa and its potential contribution to rock-related instabilities when applied erroneously. The findings of this paper necessitate a revision of current quality control and quality assurance measures related to resin bolting for underground support.

Nov 24, 2025

By M. J. Kanda, T. R. Stacey

Thin spray-on liners (TSLs) have been used as sealants and rock support in tunnels for over 25 years. Laboratory tests have indicated satisfactory properties that can provide adequate strength, adhesion, toughness, and elasticity as part of rock support systems in mining excavations. These characteristics are, however, not always demonstrated in practice, when mine environmental conditions do not correspond with laboratory environmental conditions. The shortcomings of TSLs experienced in the mining industry have raised concerns, resulting in scepticism from some operators regarding their utilization. The research described in this paper aims to investigate TSL performance in environmental conditions similar to those experienced in mines. Brazilian indirect tensile (BIT) specimens were prepared from precast shotcrete and coated with TSLs. The specimens were then exposed to different environmental conditions for up to 112 days before BIT testing under various conditions: laboratory room temperature and humidity; saturated room temperature; and combined saturated and high temperature (50°C). Additional uncoated shotcrete and TSL BIT specimens were prepared for comparison purposes. The results of the BIT tests showed that environmental conditions have a significant influence on the tensile strength enhancement of shotcrete by TSLs. Water-based TSLs are most likely to be suitable for high humidity environments, although their performance decreases at higher temperatures. Numerical modelling of TSL-coated BIT samples confirms the potential limitations of designing TSL support based only on laboratory testing carried out under room conditions.

Jul 1, 2021

By E. Córdova, A. Anani, W. Nyaaba

Optimization of panels, haulage fleet, and waiting area involves deterministic and low-fidelity methods and experiential knowledge. The process is challenging because coal recovery and operational capabilities must be considered in the solution. The approach in this manuscript comprises the development of an integrated stochastic simulation model of a coal room-and-pillar system that addresses these challenges. The decision variables evaluated are panel width, number of shuttle cars, and change-out time (COT). The results show that the mine should implement the shortest possible COT, decreasing the cycle time and thereby increasing productivity and continuous miner (CM) utilization. The highest productivity and CM utilization for a fleet size of three shuttle cars is found in the 15-entry panel width. For the evaluated fleet sizes, the 19-entry panel width is optimal for the four and five shuttle cars. Among the three variables studied, panel width and fleet size had the most significant effects (5% increase) on the CM productivity, cycle time, and utilization.

Apr 2, 2022

By J. W. Latilla, J. J. van Wijk

In late 1997 a request was received to assist with determining the powered support unit (shield) load capacities for the planned 2 seam short wall. This project had a number of aspects which made it attractive to utilize numerical modelling in conjunction with other more conventional design tools in the design of the shields. Amongst these were: The 2 seam panels were to be laid out about 25 m below the previously short walled 4 seam, the 4 seam had in turn been over-mined by the 5 seam long wall, the proposed face height of the 2 seam short wall was 5.5 m while the 4 seam had been mined at 4 m. The top seam in the area (5 seam) had been mined at between 1.5 and 2.2 m high, the face conditions with about 95 m of broken material applying dead weight loading to the 2 to 4 seam inter-burden septum were hard to predict and cyclical loading due to the presence of strong sandstone bands in the 2 to 4 seam inter-burden. The basic thrust of the study was to take the known, and successful, situation (4 seam short wall) and carry out comparative modelling to enable prediction of likely 2 seam conditions. Some two dimensional aspects studied were: 5 m goaf hanging up behind shields, stresses in beams to determine likely first goaf roof span, stresses in cantilever beams to asses cyclical loading due to sandstone bands in the interburden being loaded by the overlying goaf and stresses on chain and crush pillars adjacent to the goaf edge. Three dimensional aspects that were investigated included: Load distribution along face for close goafing and 5 m goaf hang-up and load in a 1 m wide rib modelled in the position of the powered support units. From the modelling it was possible to determine the optimal shield leg capacity of the new 2 seam equipment. These outputs were used when drawing up the technical specifications for manufacture of the new equipment. The face was successfully commissioned in August 2002. Fin 1997, requête fut faite pour aider à la détermination des capacités de charge pour l’unité de soutènement mécanisée (bouclier) pour la couche 2 courte taille en projet. Certains aspects de ce projet le rendaient intéressant pour utiliser la modélisation numérique en même temps que d’autres méthodes conventionnelles pour la conception des boucliers. Parmi ces aspects se trouvaient : Les panneaux de la couche 2 devaient être placés environ 25 m au dessous de la couche 4 courte taille ; la couche 4 avait été remplacée par la couche 5 longue taille ; la hauteur de taille proposée pour la couche 2 courte taille était 5.5 m, tandis que la couche 4 avait été exploitée à 4 m. La couche supérieure de la région (couche 5) avait été exploitée entre 1.5 et 2.2 m de hauteur ; il était difficile de prédire les conditions de taille, avec environ 95m de matériaux cassés ajoutant une charge morte à la plaque de séparation entre les couches 2 et 4 et un chargement cyclique causé par des bandes de grès dans l’entre-fardeau 2-4. L’idée principale de l’étude fut de prendre la situation connue et réussie (couche 4 courte taille) et de faire une modélisation comparative pour prédire les conditions probables de la couche 2. Certains des aspects à double dimension qui furent étudiés étaient : Un accrochage de remblai de 5m derrière les boucliers ; contraintes dans les poutres pour déterminer le premier intervalle probable entre remblai et toit ; contraintes dans les poutres en porte-à-faux pour évaluer le chargement cyclique causé par les bandes de grès dans l’entre-fardeau qui est accablé par le remblai et les contraintes sur les piliers par chaîne et d’écrasement adjacents au bord du remblai. Aspects à trois dimensions qui furent étudiés : Distribution de la charge le long de la taille pour les remblais proches et l’accrochage de remblai de 5 m et la charge dans une nervure de 1 m de large modelée dans la position des unités de soutènement mécanisées. La modélisation a permis de déterminer la capacité de portée optimale du bouclier du dispositif nouveau pour la couche 2. Ces résultats furent utilisés pour dresser les spécifications techniques pour la fabrication de l’équipement nouveau. La taille fut commissionnée avec succès en août

Jan 1, 2003

By H. S. Sichel

Statistical valuation of diamondiferous deposits By H. S. SICHEL, D.Sc The valuation of diamondiferous deposits depends on (i) the density distribution, (ii) the size distribution of stones and (iii) the selling price structure prevailing at a particular time. In the density distribution the stochastic variable is defined as the number of individual stones found per sample unit irrespective of the stone size. The density distribution is discrete and allows for barren sample units. As diamonds often occur in clusters, a Poisson mixture distribution is derived which is entirely new, as existing discrete distributions cannot represent the stone number frequencies found in nature. For the sizes of diamonds, which are measured by weight, a new compound logarithmic normal distribution is developed. Combination of (i), (il) and (iii) leads to a meaningful appraisal of diamondiferous ground expressed in monetary value per production unit of mining. Finally, confidence limits are calculated which allow for inferences from sampling to recovery.

By F. T. Cawood, M. N. M. Cudjoe

The ability to conduct real-time material tracking in mines has been a long-standing challenge. Technological innovations such as radio frequency identification technology (RFID) have over the years contributed to the effective tracking of material flow and reporting of metal content. This paper outlines the laboratory procedures and results from testing the suitability of microdot technology as a viable technique for real-time material tracking in mining. The paper clarifies the reasons for conducting the test and presents the material safety data sheet (MSDS) from a South African and Canadian perspective. Microdots from three aerosol systems were immersed in water, heated to 100°C, and crushed into coarse and fine material. These tests were used to ascertain if the technology could withstand mining conditions. A strength, weakness, opportunity, and threat (SWOT) analysis was used to evaluate and compare microdot technology with RFID. It was shown that microdot technology has some potential to track ore parcels because data integrity was retained after exposure to post-blast mining conditions. However, more improvement is required to digitally detect microdots before the technology can be implemented at scale in the mining industry.

Apr 2, 2022

By A. Santana, J. Jankolovits, G. S. Reyes

The flotation of sulfide ores that contain carbonaceous gangue requires significant operational and chemical intervention to achieve suitable metallurgical outcomes. Carbonaceous gangue dilutes concentrate grades, alters the froth behaviour, reduces operational stability, adsorbs reagents, and reduces value recovery. Carbon management processing strategies like preflotation and depression are often presented as point solutions. Moreover, oversimplified mechanisms of carbon depressants belie their complex and nuanced impact on flotation behaviour. Optimising the flotation of carbonaceous sulfide ores requires a holistic consideration of interactions between the carbon management reagents and the processing strategy, ore mineralogy, flotation behaviour, flowsheet, and all other aspects of the flotation system. Examples are shown where conventional, simplistic mechanisms of carbon depressants fail to explain the observed flotation behaviour. The multifaceted impacts of carbon depressants on froth behaviour, collector performance, and value recovery highlight the need for a holistic approach to carbon management. Keywords: Carbon management, carbonaceous ores, sulfide flotation, carbon depressant

Jan 1, 2020

By R. C. Urquhart, D. D. Howat, R. I. L. Guthrie

Heat losses from ladles during teeming by R. C. URQUHART, M.Eng. (McGiII), Ph.D. (Visitor). R. I. L. GUTHRIE, B.Sc. (Eng.) (London), A.R.S.M., Ph.D., D.I.C. (Visitor), and D. D. HOWAT, B.Sc. (Glas.), Ph.D. (Fellow) In an investigation of the loss of temperature by liquid steel during a teeming operation, a numerical technique was used to calculate the heat flows and the rate of temperature drop over the entire teeming operation. The calculations show that, before teeming, approximately 50 per cent of the heat loss is into the ladle wall at the level of the metal. As teeming progresses, the amount of heat lost by radiation to the wall above the metalline increases. The effect of variables, such as initial metal temperature, the preheat of the ladle and ladle cover, and delays, on the rate of temperature loss by the metal were determined.

Jan 11, 1973