Search Documents

The objective is to provide effective training on refuge chambers for underground coal miners. This training will increase knowledge about how to teach miners to operate, transport, and inspect a refuge chamber; what to expect psychologically and physiologically inside a refuge chamber; and how to decide when to use a refuge chamber. Background During 2006?2007, several disasters occurred at U.S. underground coal mines, resulting in 28 fatalities. These disasters led to new approaches to mine safety and health, as well as new federal regulations. One new technology mandated by federal legislation is the refuge chamber. Refuge chambers are movable shelters that are either made of steel or inflate from a steel skid as a tent. They can potentially save the lives of miners during an underground mine emergency by providing breathable air, food, water, and a safe environment for up to 96 hours. Because the refuge chamber is a new technology, recommendations, information, and training products are greatly needed.

Nov 1, 2009

By Rudolf E. Greuer, Linneas W. Laage, Xinton Chang

All output is saved in the file MFIRE OUT m the di¬rectory and on the disk containing the program The file can be inspected with a text processor and sent to a print¬er, if needed CONTENTS OF OUTPUT FILE The comment lines, reference temperature, air densi¬ty, a table of the units of measure for the results, and the average values are shown at the beginning of MFIRE OUT All input data will be shown in the output file if LOUT on Control line number 1 is _<-1 For each contamination source, a new branch will automatically be setup The new airway and junction ID numbers will not interfere with the original numbering scheme of the data file Next are the results of the selected simulation(s) in the following order network balancing, network balancing considering temperatures, transient-state modeling, and altered equilibrium due to fire and distribution of the contaminants. Depending upon the contents of the data file, and the simulation selected, attention, warning, and error message will be shown at locations where calculations resulted in unusual conditions

Jan 1, 1990

By D. K. Ingram, G. L. Mowrey, T. R. Rehak

This paper summarizes fly rock and blast area security fatalities from 1989 to 1999 and examines the causative factors. Coal and nonmetal mining used about 43 billion pounds of explosives and blasting agents between1989 to 1999. A majority of this consumption was used at surface mines. Accident data indicates that fly rock and lack of blast area security were the primary causes of blasting related injuries in surface mining. Fatal injuries due to lack of blast area security were attributed to: failure to clear blast area; failure to follow instructions; inadequate guarding; inadequate blasting shelter; and unsafe location. Seven fatalities due to fly rock and lack of blast area security were reported in surface coal mines and six in nonmetal mines. Out of these, two fatalities (one each in coal and nonmetal mines) occurred outside the mine property. In the coal mining sector, two fatalities were attributed to fly rock, and five to lack of blast area security. In the nonmetal mining sector, three fatalities were attributed to fly rock, and three to lack of blast area security. Preventive measures include: ensuring that all personnel have evacuated the blast area during shot firing; using adequate blasting shelters for employees whose presence is required in the blast area; controlling and monitoring all entrances to the blast area; ensuring that the blast is properly designed, drilled, and loaded; and emphasizing education and training to enhance skill levels for implementation of engineering control techniques.

By R. C. Wang, W. M. McKewan

The behaviour of wire ropes used in mine hoisting is not well understood. In an effort to improve this understanding, the structure of round-strand wire ropes was analysed. This report provides a generalised mathematical model that completely describes the geometry of the wires. It consists of two sets of vector equations and is valid for any round-strand wire rope. One set of equations is used to trace the paths of wires that have the form of a single helix. The other is used for the paths of double helical wires. The specific model for a 33-mm 6x1 9 Seale, IWRC, right regular lay wire rope was presented as an example. The paths and the geometric properties of the wires which include the path length per lay of strand, the curvature, and the torsion were determined from this model. In future work, the model could be used to conduct stress analysis for the wires in the deformed rope at a given rope strain and also to study the effect of wear and breaking of wires on strength loss for the various round-strand wire ropes used in mine hoisting.

By G. E. McElroy

"The development of certain mines in the East Tintic mining district, Utah, has been hindered considerably by the presence in the rock strata of heavy irrespirable gases which at times flood the lowest working places, as well as by abnormally high rock temperatures in the lower horizons. A study of these features was completed in the spring of this year, and the information obtained is summarized here.Heavy gases.Only four mines have been affected to date by the presence of heavy gas, and only one of these is producing lead-silver ores in quantity. These four embrace a territory extending about three miles north and south and about two miles east and west, while both within and fringing on this territory are a number of prospects which have not been affected.Thus far no fatalities have resulted from gas inflows, but a number of men have been temporarily overcome, and a few have had narrow escapes from death by suffocation. That the record is not more serious is mainly due to the fact that the gas inflow, as a rule, is relatively slow, mining operations have been quite carefully conducted, and the presence and extent of a gas inflow can be easily determined by its extinguishing action on the flame of miners' lights.When first encountered, about 1910, gas inflows occasioned much lost time. In some months the lost time averaged as much as ten days, while one mine cites for a certain month a maximum of 26 days lost out of a possible 28 working days. With improvements in mechanical ventilation and the passing of time, interference with work from the presence of gas has gradually lessened. During the last few winters, the main trouble has been with the mines being flooded with gas overnight when fans were not operated, although men have been driven out of the lowest development openings several times each winter with fans operating. At present, the main danger is in the lowest development openings having only one exit, wherein men might be trapped and possibly suffocated during an unusual and extremely rapid inflow of gas, or during an ordinary inflow, should the one source of power for the fan be disabled."

Aug 1, 1921

Volumetric measures [ ]

Jan 1, 1962

By A. J. Miscoe, W. M. McKewan

A unique machine for inducing bending fatigue in wire ropes was built at the U.S. Bureau of Mimes&apos; Pittsburgh Research Center. This machine can produce nine levels of degradation through repetitive cycling of long samples of wire ropes of the types used in the mining industry. This report provides an analysis of the results of the first wire rope to be fatigued on this machine. These results have indicated that as a wire rope accumulates bending cycles, its strength first decreases because of wear and then in- creases due to cold working of the wires. As the amount of cold working increases, more and more of the embrittled wires break and the strength of the rope decreases rapidly. In this test, application of several of the regulatory retirement criteria to various sections of the rope suggests that there may be some inconsistency among them.

Jan 1, 1993

Although coal is found in several locations in Virginia, almost all recent mining has occurred in the southwestern part of the state. Potentially minable reserves are estimated at 2.6 billion tons, slightly less than one percent of the national total. Coal ranges from high- to low-volatile bituminous, and seams average three to four feet in thickness. Virginia produces coal with higher BTUs (British Thermal Units) and a lower sulfur content than the national average. Historically its high quality has made Virginia coal attractive for metallurgical coke production and for the export market. Coal production and related industries have a significant economic impact in southwestern Virginia. In the seven coal- producing counties, coal mining is the major industry. In the two largest coal-producing counties (Buchanan and Wise), over 40 percent of total earning is derived from the coal industry. Virginia&apos;s regulatory program was conditionally approved December 15,198 1, and received final approval May 8, 1984. Its Abandoned Mine Land Program was approved with the regulatory program December 15, 1981, with emergency program authority approved November 13,1987.

Jan 1, 1992

By Jeffery L. Kohler, Eric R. Bauer

Prolonged exposure to noise over a period of years generally causes permanent damage to the auditory nerve and/or its sensory components. This irreversible damage, known as noise-induced hearing loss (NIHL), is the most common occupational disease in the United States today. Workers suffering from NIHL have difficulty understanding human speech and hearing other workplace cues. Despite the use of regulations and efforts by government and industry to reduce NIHL, the problem today is as prevalent as it was more - than two decades ago. Recently, the Mine Safety and Health Administration (MSHA) promulgated a new regulation that is designed to reduce NIHL in the mining industry. One of the more significant provisions is the elimination of MSHA&apos;s past practice of giving "credit" for the use of personal hearing protection, thereby reestablishing the primacy of engineering and administrative controls. However, there is a knowledge gap that is impeding the development and implementation of engineering and administrative controls. Although significant data exist on the exposure to noise by occupational code, little is known about the noise sources that contribute the most to the worker&apos;s dose. This is problematic in a workplace with multiple noise sources and workers who travel among noise sources. Yet without this knowledge, it is difficult to focus control efforts in any practical manner. Thus, it is important to characterize noise sources sufficiently well so that the sources most hazardous to hearing are identified and those conditions of exposure that are most amenable to engineering controls are pinpointed as well. The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) is conducting a cross-sectional survey of noise sources and worker noise exposures in the mining industry to address this deficiency. The initial effort, conducted at a coal preparation plant and results are described in this paper. Preliminary analyses indicate that the noise levels on all floors exceeds 90 dBA in most areas, and that levels as high as 115 dBA were recorded. In addition, the one worker whose responsibility is to monitor the equipment and "house clean" the plant is slightly overexposed, even though he spends only half the shift in the plant. General information on the hearing loss problem in mining, a review of hearing protection use and noise regulations in mining, and other background materials are also presented.

Three -dimensional boundary value problems are difficult to solve. Indeed, while the separation of the scalar wave equation can be effected in 11 different coordinate systems, an analytic solution requires that the boundaries, both external and internal, possess the same symmetry as the coordinate system. Numerical methods are thus of great importance for the solution of such problems; however, despite the availability of high-speed, large memory digital computers , the solution to a significant three -dimensional problem is by no means trivial. It is unfortunate that the results reported here by Jones are invalid. Jones discusses a model in which a three-dimensional island lies off a linear coastline where all the interfaces lie in the coordinate planes in a Cartesian system. A downward plane em wave polarized with the electric field parallel to the linear coastline, and two of the islands coast, is incident downward. This, of course, requires that the incident electric field is perpendicular to the other faces of the idealized Cartesian island. The significant equation used by Jones for his finite difference calculations is [ ] where n2 = sµ? . is the conductivity, µ=µo is the permeability of the appropriate medium, and w is the angular frequency of a Fourier component of the incident field. We see that the displacement current term is omitted, which is an excellent approximation for the parameters of interest in this model. In the similar equation for the y- component of the diffusion equation, the same considerations which we are about to discuss are equally valid. It can be seen from the equation that the field components are related and thus any errors introduced will be propagated into all three components. The difficulty arises when Ex or E is perpendicular Y to one or other of the surfaces of discontinuity in s. The continuity of current at the air-earth interface (upper surface), e. g., jy, requires

Jan 1, 1973

This chapter presents data on occupational exposures from several sources. Data from compliance samples obtained by MSHA inspectors are presented in table 6-1 for coal mine dust and silica dust, and in tables 6-2 through 6-6 for metal fumes. Since these samples were taken for compliance monitoring rather than as part of a survey of the industry, it is difficult to predict how well they indicate actual exposures for all mining operations. In the coal industry, 7.8% of all respirable dust samples during 1986-1995 were above the permissible exposure limit (PEL). Of silica dust samples obtained during the 10-year period, 23.7% were above the PEL in coal, 16% in metal, 10.8% in nonmetal, 9.1% in stone, and 7.6% in sand and gravel. Of metal fume samples, silver samples showed the largest percentage above the PEL-approximately 48% of samples in both metal and nonmetal. Tables 6-7 and 6-8 present data on noise exposures from the MSHA "dual threshold" survey, which was published in the Federal Register [61 Fed. Reg. 66347 (1996)] as part of a proposed rule change for occupational noise exposure in mining. This study examined a group of samples obtained during 1991-1995 and compared the percent of samples that were above two separate specified limits. The first limit was the current noise standard, a time-weighted average of 90 dBA, calculated to include only exposures at 90 dBA and above. The second limit was a time-weighted average of 85 dBA, calculated to include exposures at 80 dBA and above. Tables 6-8 and 6-9 refer to musculoskeletal overload conditions examined in the National Occupational Health Survey of Mining (NOHSM) [NIOSH 1996]. Table 6-8 shows the operational definitions for each condition; table 6-9 shows the percentage of the workforce potentially exposed, by commodity. Across all commodities, a large proportion of workers were exposed to musculoskeletal overloads due to positioning of the neck and back; positioning and motion of the forearms, arms, and shoulders; heavy lifting; and positioning and movement of the lower limbs. The recorded overloads were defined in the survey and did not exceed any NIOSH, MSHA, or OSHA guidelines for musculoskeletal overloads. Further information on this survey appears in appendix A.

Jan 5, 2000

By R. V. Ramani, V. T. Burgos, J. A. McClay

Summary Cost models have, long been confined to the accumulation and analysis of static-data.. While historical and time study data are valuable for control of existing operations, for new systems and equipment, and for projections, they need to be adjusted or modified. The availability of computer-oriented systems simulators provide yet another method for costing these systems and equipment. This investigation has introduced a concept whereby continuous, variable data can be assimilated and analyzed through the combination of an economic analysis model, which includes a direct costing capability, with a systems simulator. This tandem operation permits increased flexibility and greater atten¬tion to detail in the evaluation of mining systems. The direct costing process is carried throughout the majority of the model operations. Labor and capital costs may be computed directly, even in the absence of the systems simulator, while operating costs re¬quire input parameters, at present, from the subsystems of the Master Design Simulator. Since the costs computed are based on the perfor¬mance of each individual machine unit, the model may be used to evaluate equipment compatibility, system interaction at the mining face, and the effect of system elements on total mining costs. Additional applications of the cost model include the following: 1. Complete mining systems may be evaluated, over their economic life, to determine the feasibility of a profitable operation. 2. Costs associated with mining various segments of the coal deposit may be computed as a guide to planning the mine layout and scheduling the sequence of operations or acquisition of new

Jan 1, 1975

The Crow Indian Reservation is located in the southeastern part of Montana, stretching from near Billings, in the center of the state, to the Wyoming border in the south. The Office of Surface Mining&apos;s Casper, Wyoming, Field Office is responsible for regulating mining and reclamation on Crow tribal land. Federal legislation enacted July 11, 1987, authorized the Indian tribes to implement approved Abandoned Mine Land Reclamation Programs. In early 1988 the Crow elected to develop an Abandoned Mine Land Program under the Title IV provisions of SMCRA. The tribe&apos;s plan received final approval on January 4, 1989.

Jan 1, 1992

By Margaret R. Egan

In an underground mine fire, a toxic mixture of combustion product gases and particulate matter is transported by the ventilating system endangering everyone downstream. To determine the magnitude of the problem that these toxic combustion products pose, the U.S. Bureau of Mines is investigating the combustion products of typical materials found in underground mines. The total toxicity of the combustion products depends upon the evolving gas species and particulate matter, the amount of material involved, and the ventilation rate. In a simulated mine environment, the products from smoldering poly- vinyl chloride (PVC) brattice and conveyor belting were analyzed for gas concentrations and smoke characteristics. The primary toxic gases are hydrogen chloride (HC1) and carbon monoxide (CO). Smoldering conveyor belts are more detectable than smoldering PVC brattice cloths. These results, combined with previous analyses, are used to estimate relative toxicities, product levels, and detect-ability of smoldering mine combustibles.

Jan 1, 1992

By T. E. Marshall, D. R. Dolinar, T. M. Barczak, T. P. Mucho

Over a portion of the older limestone mine workings at the NIOSH Lake Lynn Laboratory, a mining health and safety research facility, a large sinkhole formed caused in part by the intersection of several tightly spaced joint sets and unusual weather conditions. The anticipated propagation of the associated roof failures threatened to encroach upon a portion of the facility’s secondary escapeway. To protect the escapeway, two cribs walls and over 80 cable bolts were installed. In addition, extensometers were installed to monitor roof movement in the escapeway. However, a large roof fall associated with the propagating roof failures in the sinkhole area partially destroyed one crib wall where the adjacent escapeway was not reinforced by cable bolts. Recent roof movement information indicates that this area is still active. Based on these measurements, steps have been taken to stabilize this portion of the escapeway. This paper discusses roof monitoring, the roof movement, the large roof fall, propagation of the roof failures, and the recent support measures undertaken to stabilize the escapeway.

By C. P. Fang

"For lower stages of multinozzle micro-orifice impactors, as many as two thousand nozzles are uniformly arranged within a cluster diameter of 1.06 inches. In the impaction region the mass flowrate of the spent air increases along the radius and reaches a maximum at the periphery. This crossflow can significantly deflect the air jets of the outer nozzles, hence the characteristics of impaction changes.Investigators in heat transfer and fluid mechanics have studied the influence of crossflow on jet deflection and found the dimensionless deflection of the jet centerline X/Dn is a function of (S/Dn)(l/m) . only, here X is downstream coordinate measured from the center of the jet orifice, Sis the jet-to-plate distance, Dn is the orifice diameter and m is the jet/crossflow mass flux ratio defined as:"

Jan 1, 1989

By D. Harrington, C. W. Owings

"The belief is now fairly general among the coal-mining people of the United States that one of the most effective methods of preventing wide-spread coalmine .explosions is that of introducing rock-dust into coal mines to reduce the inflammability or explosibility of dusts found on mine surfaces. Notwithstanding this belief it is improbable that even a small fraction of 1 per cent of the coal mines of the United States are at all adequately protected by rock-dust; in a survey made in the summer, and fall of 1927 it was found that but 463 out of more than 7,000 operating bituminous and lignitic coal mines were using rock-dust at all, and that few if any of the 463 were fully or adequately protected by rock-dusting.Inspections of a large number of mines through the United States by Bureau of Mines safety division field men have failed to reveal a single adequately rock-dusted mine, Yet there is no doubt that many of the owners and operators believed their properties to be fully protected by rock-dust against the much-feared hazard of widespread explosion. Two of the most disastrous explosions of recent years occurred at properties where the owners were definitely of the belief that the rock-dusting done had made the mines immune to widespread explosion involving coal-dust. In both instances it was found that although some rock-dusting had been done, the mines were more nearly 1 per cent than 100 per cent rock-dusted.This condition as to inefficiency or insufficiency of rock-dusting in the coal mines of the United States is almost universal, and unless our mining men awaken to its, dangers, the disaster record of the coal-mining industry is much more likely to become worse than better. During the fiscal year ended June 30, 1928, the attention of the safety division of the United States Bureau of Mines was called to. 22 explosions With 320 fatalities in bituminous coal mines of the United States; and of the 22 explosions there were 10 with 258 fatalities in mines that were listed as having used rock-dust; upon investigation it was found that as usual the rock-dusting had been anything but comprehensive or adequate. It is probable that in a very few instances last year the relatively small amount of rock-dusting stopped the .extension of the explosion and thus prevented further expansion of the death list. In general, however, the explosions occurred in a part of the mine that had not been rock-dusted - and right here is the crux of the failure or probable failure of present-day rock-dusting in the United States, There should be no part of any bituminous or coal mine in which all of the exposed surfaces (roof, ribs, and floor) have not been thoroughly rock-dusted and kept thoroughly rock-dusted. In other words, all exposed surfaces of all accessible places in bituminous and lignitic coal mines should be kept covered with rock-dust so that the combined rock-dust coal-dust mixture at all times and in all places has less than 35 or 40 per cent combustible matter, The only exception to this rule is that surfaces which are wet (and this does not mean merely damp) need not be rock-dusted. However, a mine opening may have several inches of water on the floor and yet have much explosive dust on the ribs and roof above the water; in such places the ribs and roof should be kept rock-dusted, irrespective of the wetness of the floor."

Nov 1, 1928

By L. C. IlsLey

The Bureau of Mines has collected field data and made laboratory investigations of trailing- cable performance in the hope of developing a better and safer cable for use with permissible mining machines . Because of their better insulation and performance , only rubber- sheathed cables were finally considered . The cables tested represented the product of six manufacturers . : After consideration of the results of the preliminary investigations , the conditions under which cables are used in mines , and the better performance of the later types of cables that were submitted as the investigation progressed , the bureau formulated a performance - test requirement and notified the cable manufacturers as follows : The hazards of the trailing cable are such that the bureau has been unable to extend beyond the machine its formal approval to cover the cable as at present developed . However , in the attempt to reduce the hazard as much as possible , cables passing certain tests will be recommended for this service and it is hoped that several cables will be developed to meet this requirement .

Sep 1, 1930

By N. T. Lowe, R. E. Miller

When two pieces of heavy equipment interact, jolting and jarring can occur. During haulage truck loading for example, there is a chance that the operator of one or both pieces of the equipment will experience jolting and jarring. Additionally, a jolt can occur when an off highway equipment operator drives over a road defect or inadvertently strikes a berm. Aside from the operators, there is seldom anyone else that witnesses the interaction and can accurately describe the extent of the jolting. This makes it difficult for health and safety managers to address jolting and jarring. The devices and software described in this paper constitute a method for installing “black boxes” called Shox Boxes onboard equipment that already have a GPS system onboard. The resulting configuration provides an objective assessment of jolting and a chance to determine the root causes of it. The Shox Box system reviews data in real time, onboard the vehicles, 24 hrs a day, and sends pertinent information via radio to a central database. The data generated shows whether jolts are above or below a supervisor defined target value for the equipment and the tasks being performed. This allows health and safety personnel to demonstrate safe operation of heavy equipment and recommend proactive actions to maintain jolting within a reasonable range.

By Oliver Bowles

"A New Mica Company in China A report has been received from the American Consulate at Chungking, China, to the affect that a new company has been organized to operate a mica mine north of Ta-chien-lu, in the province of Ssu-Chuan. The company, which is entirely under Chinese management and control, has a working capital of $10,000. While comparatively new, the mine has been worked before, and apparently with some success. The mica is said to be of good quality. It is claimed that the deposit will supply a limited amount of mica that will cut in pieces a foot square or over, and larger quantities of smaller sizes. The chief difficulty is transportation, for it is reported that a ten days' journey, part of it over mountain trails, will be necessary to transport the mica from the mine to Yachow, the nearest practical waterway. It is probable, therefore, that the output of the mine will be limited.Necessity for Careful Trimming and Grading of MicaA recent report to the Department of Trade and Commerce, Ottawa, Canada, by Acting Trade Commissioner C. G. Venus, London, England, contains information which is of vital interest to mica producers in the United States. It is pointed out that mica exports from Canada to England show a gradual decline dur¬ing recent years, the figures being as follows: 1913- 1,383 cwt: 1914 - 1,225 cwt: 1915 - 1,864 cwt: 1S16 - 879 cwt: 1917 444 cwt: 1918 - 480 cwt. Shipments from India to England, on the other hand, show a steady increase from 40,178 cwt. in 1913 to 66,401 cwt, in 1918."

Jan 1, 1920