Search Documents

By Travis Rhoden

Merriam Webster?s Collegiate Dictio­nary (1996) defines team as ?a number of persons associated together in work or activity? and teamwork as ?work done by several associates with each doing a part, but all subordinating personal prominence to the efficiency of the whole? (page 1209). According to Dr. Geller, author of Building Successful Safety Teams: Together Everyone Achieves More (1998), a team of people working together for industrial safety consists of as few as two people or as many as fifteen who have complementary skills, assignments, or abilities for completing a particular task. Effective teams have members who share a common mission and relevant goals, and they share specific methods to reach their goals and accomplish their mission. They also have an evaluation system in place for holding themselves mutually accountable for goal-directed responsibilities.

Nov 1, 1998

By V. E. Homme, M. M. Wong

Tests were made in reactors ranging from 12 to 30 inches in diameter to develop methods for the preparation of sodium chloride - titanium lower chlorides ( dichloride and trichloride ) melts that contain titanium predominantly in the divalent state . Such melts are desirable as a starting material for the production of titanium metal or as an electrolyte for electrorefining of titanium . Sodium reduction of TiCl with an 18 - hour period of holding the reaction products in the molten state produced melts that contained titanium lower chlorides in TiCl₂ - to - TiCl , molar ratio of approximately 8 to 1. Sodium reduction of TiCl in a reactor with a shielded pipe weir , that required no melt -holding period , produced melts with a TiCl₂ - toTiCl , molar ratio as low as 4 to 1 . Reduction of TiCl4 with scrap titanium metal in molten sodium chloride produced relatively pure melts containing about 27 percent titanium in a Ticl₂ - to - Ticl , molar ratio of approximately 4 to 1 .

Jan 1, 1964

By H. W. Frevert, A. C. Fieldner, S. H. Katz

"The Bureau of Mines, in its investigations of as masks for use in mines and allied industries tests masks that are voluntarily submitted by manufacturers for examination, and issues approval certificates for masks that meet the bureau's specifications. This paper describes the tests that were conducted on an ammonia gas mask by the Bureau of Mines, which successfully met all requirements and tests for ammonia, masks. The mask tested, known as the GMD ammonia gas mask, is manufactured by the Mine Safety Appliances Co., Pittsburgh, Pa. This ammonia gas mask, which forms a pocket over the face and allows breathing through the nose, consists of a face-piece with non-shatter eyeglasses; this is attached by means of a corrugated rubber tube to a canister supported on wearer's chest by a harness. The canister is green in color and is of tinplate construction. It was a disc valve at the bottom to prevent exhalation through the canister. The filling of the canister consists of a specially impregnated activated charcoal, about 750 c.c. in volume and weighing about 520 grunn. The material is supported above the check valve by a dome of wire screen covered with toweling. Above the granular material is a filter of absorbent cotton screens, and all materials are hold firmly in place by pressure from strong"

May 1, 1926

By A. D. Garman

This paper presents one of a series of digests of foreign mining legislation and court decisions which is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countries. This interpretation of the laws of Guatemala has been prepared from the best available information in Washington, but is released subject to correction and amplification, if necessary, by the proper American diplomatic and consular officers to whom it is being referred through the courtesy of the Department of State.

Oct 1, 1929

Underground and strip mining (6,7) produce different hydrologic environments. Many underground mines are below the zone that is completely saturated with water and the mine openings may cause new and continuous contact between sulfurous material and water which flows from the saturated zone to the workings. Strip mines are usually above the zone of continuous saturation and contact between sulfurous material and water is generally restricted to periods of precipitation. A full appreciation of the problem of water pollution caused by drainage from deep mines requires a basic understanding of occurrences and movement of water in the ground and the modes of ground water entrance into mining areas.

Jan 1, 1970

The Bureau of Mines has developed test procedures and criteria for evaluating explosive reactivity of explosive-contaminated solid waste substances generated by U.S. Army ammunition plants. These substances are produced as explosive-contaminated sludge from wastewater treatment plants, residues from the burning of munitions and explosives on open ground, and residues from deactivation furnaces. The characterization of explosive reactivity is a prerequisite for disposal of such waste materials, which may be contaminated with primary explosives, propellants, or pyrotechnic materials. The Bureau has proposed two tests for this purpose. These tests were developed to evaluate the explosive reactivity as defined in Title 40, Code of Federal Regulations (CFR), part 261.23(a)(6) and (7). These are the Bureau's gap and internal ignition tests, which determine the sensitivity to shock and thermal stimuli, respectively. This report also includes gap and internal ignition reference data for typical blasting agents, high explosives, propellants, and marginally reactive substances. These reference data were used to establish test criteria. The Bureau has evaluated over 400 samples of contaminated soil, sludge, and burning residues using these two test methods.

Jan 1, 1988

By Peter F. Steidl

Seven degasification wells have been completed in the Pittsburgh coalbed at the new Emerald mine near Waynesburg, Pa. Funding was provided by the Bureau of Mines to perform stimulation treatments on five of the wells, to show that this is a feasible and economical means of degasifying part of a coalbed. The seven wells ranged in depth from 590 to 910 feet. Stimulation treatments used 25,260 to 42,660 gallons of foam and 7,400 to 12,800 pounds of 20/40-mesh prop sand. Pumping rates were 10.8 to 11.6 bbl/min and treating pressures were from 1,050 to 1,600 psig. On the day following stimulation, gas production ranged from a few hundred cubic feet per day to more than 100,000 cu ft/day.

Jan 1, 1978

By M. L. Fenger, S. F. Mauser

This 1s a report on an Investigation performed during Contract No. H0166069 "High and Medium Voltage Trailing Cable Splices and Connections," which presents a summary of the requirements formulated. The requirements are presented in the form of considerations for medium-voltage splices, and medium- and high-voltage couplers used in underground coal mines.

Jan 1, 1979

To concentrate coarse mica particles using a dry beneficiation technique. Approach Concentrate coarse, II berated mica particles using a Bureau-designed system of crushers, screens, and a two-stage zigzag air classifier. How It Works Because mica has a flat plate-like crystalline structure, mica particles are significantly lighter than blocky gangue particles of the same size fraction. Thus an air classification technique can separate the flat, light mica particles from the heavier gangue particles. The ore, which Is first run through a standard jaw crusher, a roll crusher, and a hammer mill to liberate the mica, enters the rougher Zig-zag section through a rotating air lock. See photograph and diagram of a 2-stage air classifier. Airflow through the classifier can be varied according to the size of the particles being separated. The gangue material falls through the airstream of the rougher zigzag section and is discarded as tailings. The mica flakes are carried by the air-stream to the cyclone shown on the right side of the diagram, where they are collected. This rougher mica concentrate is fed to the cleaner zigzag section through another rotating air lock. The mica particles are again carried by the airstream but they are now collected In the cyclone on the left side. The cleaner concentrate leaves the left-side cyclone through a third rotating air lock and is rescreened to remove under-size material missed by the first screening. The final product of this pneumatic process is generally a high-grade mica concentrate. A generalized flow diagram for the pneumatic concentration method Is shown In the second diagram.

Jan 1, 1981

By M. M. Tilman

The purpose of this investigation was to determine the effects of small amounts of cobalt in nickel on the tensile properties and hardness of representative types of austenitic stainless steels . Cobalt substitutions for nickel up to 2 weight - percent were made in types 302 and 309 stainless steels . Data were obtained at room temperature for tensile strength , yield strength , percentage elongation , percentage reduction in area , and hardness . In type 302 steels , tensile strength and hardness increased with increased percentages of cobalt , percentage elongation and reduction in area decreased , and yield strength showed little change . Property changes were largely due to the reduction of nickel content rather than to the addition of cobalt . In type 309 steels , only minor variations were observed for the properties investigated ; the effects of the relatively snall cobalt substitutions and nickel reductions were somewhat reduced by the higher total alloy content .

Jan 1, 1964

By J. R. Bartels

Operation of underground coal mine mobile equipment is usually done in a restricted workspace with reduced visibility. This work environment puts machine operators in awkward postures for tasks that require awareness of their surroundings and fast reactions to avoid hazardous situations. Using experienced equipment operators as a source, researchers conducted an investigation that developed a method to gather data on the needs and practices of machine operators while controlling the machine and the reasons for needing particular operational cues. The method used was an interview technique including a survey questionnaire and visual aids. The data gathered defined operator cues and work positions for the cutting and tramming phases of remote controlled continuous mining machines used in underground coal mines. Analysis techniques to determine which cues an operator sees from a variety of positions utilizing a computer simulation is shown to be potentially useful to the mining industry for design of work practices and workplace layout and could impact equipment design and selection for improved worker safety. Conclusions indicate that the survey was a good research tool to collect data and helped investigators understand important visual cues. Using this information, researchers were able to analyze the visual cues an operator can see from a given work position and posture.

Jan 1, 2009

By Launa Mallett, Charles Vaught, Michael J. Brinich

The lack of good communication is a very real problem in mine emergencies. Sometimes critical information is not communicated to those who need it to make decisions. At other times, those on the receiving end of a warning do not think to ask the right questions. What happens in underground coal mine fires is a case in point. The authors interviewed 48 workers who escaped three serious fires in western Pennsylvania. In each case the location of the fire was known but did not get communicated to many of those who had to evacuate. Sometimes, even the nature of the problem was not clearly communicated. Some workers began their evacuation knowing nothing about what was happening. In an effort to improve emergency communication National Institute for Occupational Safety and Health (NIOSH) researchers worked with safety professionals to determine what sorts of information are critical in a mine emergency. An extensive list was generated, which proved too long to be remembered by individuals. The list was therefore collapsed into six categories. A communication protocol was derived from these categories.

By J. F. Barkley

"A knowledge of the carbon dioxide (002) content of the products of combustion, particularly from the boiler furnace, is very valuable. An instantaneous indication of the CO2 can be used as a useful guide to efficient burning. A permanent record over a. period of time gives a story to the management which tends to keep the operators more alert. Many instruments that indicate and record CO2 have appeared within the last fifteen years. More are about to appear. Although simple principles involving chemical, physical, or electrical qualities, are being used, there is at present a general feeling of uncertainty about such instruments in the boiler room any instruments are bought, run awhile, then lie idle indefinitely.Inquiries as to CO2 machines continually come to the Bureau of Mines from the general public, as well as from other branches of the Government. Some ten years ago a series of tests was made on certain instruments at that time on the market. The following test was made quite recently on four of the newer types, including one using an electrical principle. The four instruments were installed on one boiler each, according to the instructions of the makers, and the recommended routine attention was given them. The test was of a service nature duplicating the conditions under which the instruments ordinarily serve. The boiler that was available for this purpose was practically banked for some hours of the night. This caused the average CO2 for the entire twenty-four hours to be rather low, although it reached the higher ranges of the instruments during the day.Each day the charts were averaged and the results plotted to form the accompanying curve. The record of each instrument is shown by its particular mark, the dot, circle, cross and square being used in addition there is plotted for each day a rectangular area representing 1 % CO2 in height. The proper positions of this area was determined by means of the Crsat. Where the plotted point for an instrument falls within the rectangel its accuracy is within 1/2% CO2, which is considered satisfactory. Where it falls outside the rectangle, inaccuracy is indicated."

Mar 1, 1925

By W. P. Yant, R. R. Sayers, G. W. Jones

In the treatment of any illness the early diagnosis is of very great importance . This is especially true in cases of carbon monoxide poisoning , whether acute or sub-acute in character. A diagnosis of CO poisoning is usually made from a correlation of the history , the possible place of exposure , and the symptoms produced . This , however, is not positive evidence because CO often is present in unsuspected places and can be absent in suspected places . Also , the symptoms of this type of poisoning are common to other causes . In many such cases the correct diagnosis may be very difficult , if not impossible by this method and as a result little or no treatment is given . Sub- acute cases , those in which the subject is exposed to concentration sufficient to cause only headaches , malaise , feeling of weakness and dizziness , may be incorrectly diagnosed and as a result , improperly treated . Probably the best method of diagnosis is by examination of the subject's blood . Many methods for the detection of CO in the blood have been developed , but owing to their various individual disadvantages have never come into common usage . Some of the quantitative methods are satisfactory with regard to accuracy but require elaborate and expensive apparatus , special technique and training, or are too delicate and cumbersome for field use . It is of vital importance in all industrial and domestic accidents occuring at places where CO might be suspected or where the symptoms are typical of CO poisoning that a qualitative and preferably a quantitative determination be made the extent of poisoning being of importance in deciding whether CO was the direct or contributary cause) to show the presence or absence of 0. This is indeed essential from a medical standpoint as it aids in prescribing treatment and from a legal standpoint to insure justice in the claims that are often unjustly decided for want of positive evidence.

Jun 1, 1923

By Ryan G. Wade, Mark K. Larson

Researchers at the National Institute for Occupational Safety and Health (NIOSH) are studying the time-dependent response of rock stressed along weakness planes. The objective is to improve mine safety by reducing the number of roof falls that cause injuries and fatalities to miners. Researchers conducted direct-shear tests on mudstone overcored from a coal mine roof. Results showed frictional strength weakens with displacement along the shearing planes. Results of direct-shear creep tests also showed time-dependent deformation. Test measurements were compared to classical analytical models. Results suggest that risk of roof collapse may be decreased through layout and support design to reduce creep rates and thus slow progression toward failure.

By Oliver Bowles

"Waste Granite in the Barre, Vermont, District: Waste in the great granite center at Barre, Vermont, consists of three types of material, the rough blocks rejected at the quarries on account of imperfections, the chips or spalls resulting from trimming and dressing at the cutting plants, and the granular and pulverized material from the dust collectors. The waste piles at the quarries of are immense proportions and constitute a serious handicap to quarrying in that they cover up good rock deposits, and are also so large that waste disposal becomes more and more expensive. The problem of utilization of such waste material is a topic of keen interest to all granite producers.Barre is not situated on a water route, and thus transportation costs prohibit the shipment of waste blocks for rip rap or ballast. Crushing plants use a small amount of this material for road construction, but aside from this, the waste is practically valueless.Investigators of waste utilization problems are awaiting with interest further information concerning an enterprise undertaken at Montpelier, Vermont, to utilize crushed granite for the production of brick similar to sand-lime brick. Granules of granite are mixed with lime, moulded, and hardened under steam Pressure, The brick produced are said to be of excellent quality for structural Purposes.There seems to be no logical reason why waste granite could not be utilized for the manufacture of building stone, and paving blocks, for many of the defects which condemn a stone for monumental purposes are not at all detrimental for building or street paving. F or the most part, monumental stone workers are not particularly interested in other branches of the granite in-dustry, and a combination of industries such as that suggested"

Jan 1, 1920

By Oleg Terichow

Electrophoretic mobility measurements were made on samples of Florida phosphate slimes to determine the optimum conditions of coagulation and precipitation in aluminum sulfate solutions. The addition of silica sand and other selected materials as mutual coagulants has demonstrated the practicability of coagulating two dissimilar particle systems by elimination of the repulsive double layers. By proper selection of the solution and its concentration, the reduction of the double layer to a zero point of charge causes coagulation and rapid precipitation of both particle systems. Confirmation was found in filtration tests and sedimentation tests.

Jan 1, 1973

By Lambert Dolphin, George Oetzel, Robert Bollen

An electromagnetic sounder developed for an archaeological application in Egypt has been successfully tested in a California dolomite mine. Chambers in the mine 100 to 130 feet from the surface gave intense, well-defined echoes consistent with an average attenuation coefficient of 0.6dB/m and a relative dielectric constant of 11. By moving the transmitter and receiver units on the hillside above the underground chambers, various characteristics of the propagation could be observed such as dispersion, chamber aspect sensitivity and cross section. The transmitted pulse was one to one-and-a-half radio-frequency cycles long at a peak power of 0.2 MW. Frequencies employed were 16 to 50 MHz. The light weight, highly portable, battery-powered equipment is potentially suited to other underground sounding applications.

Jan 1, 1973

By Todd M. Ruff

Researchers at the National Institute for Occupational Safety and Health (NIOSH) are studying methods to prevent workers from being entangled in machinery used at mining operations. An analysis of mining accidents in the United States that resulted in a fatality or permanent disability from 2000 through 2005 showed 438 severe incidents that involved contact with machinery or equipment, an average of 73 per year. Researchers determined that the most common machinery involved in these severe accidents was conveyors. Also, a significant portion of the accidents occurred during machine maintenance and repair. Researchers are focusing on improved methods to prevent unintentional machine startup during maintenance activity and methods to detect workers near moving machine components. One new technology that shows promise for this application is intelligent video. Popular in the surveillance and security industries, these systems use cameras and computerized video analysis techniques to automatically detect the presence of people in preset zones within the camera?s field of view. A preliminary study has been initiated to determine if this technology could reliably detect the presence of workers in hazardous locations near machinery. Possible advantages of the use of this technology include improved detection zone demarcation and improved ability to distinguish between hazardous and non-hazardous proximity, compared to conventional proximity sensor techniques. Initial tests to detect a person near a conveyor system in daylight conditions showed promising results. A description of the technology, test procedures and results, implementation challenges, and future research needs are discussed.

Jan 1, 2008

By C. W. JEFFERS

During the past few years the use of mechanical equipment for the loading and transportation of coal at the working face has rapidly increased . Many mining officials are of the opinion that mechanical methods have tended to reduce the hazards of mining, and a number of statements have been made to this effect . Little actual data upon which to base conclusions in regard to the relative safety of various methods of mining have been made available . While it may be possible that these systems of mechanical mining are inherently less hazardous , obvious dangers should not be disregarded in the belief that the mere act of installing mechanical loading equipment automatically brings about better accident records . The same rules and regulations , modified to meet the new regime must be applied with the same discipline as heretofore . By diligent study and application there is reason to believe that new methods of concentrated mining can be utilized with at least a possibility of increased accident performance . With the idea of preventing accidents by taking available precautions against their occurrence , attention should be directed to the dangers that exist where room and face conveyors are in operation . Due to the cost pressure prevalent in the mining industry at the present time mechanical means are often used in an attempt to decrease cost of production. The management , after having spent considerable sums of money for new equipment , is expected by stockholders and investors to show results by increasing tonnage and reducing operating costs . Consequently the operating officials apply the same pressure to local mine officials to obtain results . The natural reaction of the superintendent and mine foreman is to secure the maximum production from the new method , and unfortunately safety is frequently , if not generally , sacrificed to this end . In many instances , operators of new types of mechanical loaders are difficult to secure and after being obtained are difficult to hold , especially if the new equipment is more or less in the experimental stage . The tendency is to handle the machine operators with " gloved hands " and to permit many unsafe practices which ordinarily would not be allowed, in order to keep from antagonizing them and losing their services . Although these unsafe practices become habitual and even uneconomical , conditions thus established are difficult , sometimes impossible , to change .

Jul 1, 1930