Search Documents

By M. R. Yenchek

The U.S. Bureau of Mines has determined a method for calculating coal mine portable power cable thermal life for a specified temperature loading. This work was the culmination of a multifaceted research project involving (1) accelerated life tests of insulation and jacket materials and (2) steady-state and cyclical loading of cables. Composite Arrhenius curves were derived for common insulation and jacket materials to identify the key cable quality that precipitates thermal failure. Plots of temperature rise versus current for popular cable sizes were then referenced to develop a correspondence between cable life, based upon thermal degradation and current loading. Predictions of cable thermal life were made through integration over variable load cycles and, consequently variable operating temperatures. This procedure may have utility for both the U.S. Mine Safety and Health Administration and mining machine designers in determining the appropriate cable size for new equipment.

Jan 1, 1991

By Byron A. Baker

The Bureau of Mines used a windowed cell to measure the phase-boundary pressures of two related series of gas-condensate fluid mixtures. Normal butane was added to the mixtures incrementally to determine its effectiveness for lowering phase-boundary pressure. All the experimental data were correlated, so that the pressure required to maintain light oils mixed with natural gas in the single phase may be computed for secondary recovery applications. The heavy hydrocarbon parts of the mixtures were distillation fractions of a Gulf Coast condensate. Intermediate normal hydrocarbons in the butane-heptane range and natural gas were added to the fractions in selected proportions, so that phase-diagram pressures of 26 fluids were actually studied. The experimental range of temperatures was 50° to 280° F. Two correlations were developed to represent phase-boundary pressures by means of a polynomial. Independent variables represent natural gas content, disparity of properties of components comprising the mixtures, and temperature. A fourth variable, for one correlation only, was the quantity of normal butane added to the original mixtures. The latter correlation with four independent variables contains 15 coefficients and is estimated to be accurate to 135 psi.

Jan 1, 1973

By Jerry E. Olson

In 1986, at the request Of the Bureau of Land Management, the U.S. Bureau of Mines studied the central portion, encompassing 20,727 acres of the 32,261-acre Badlands Wilderness Study Area (OR-005-021) in order to evaluate its identified mineral resources. The study area is located in Crook and Deschutes Counties, OR, about 12 miles east from Bend. No mineral resources were identified. The area studied is underlain by Tertiary and Quaternary basalt flows which are largely covered by a veneer of sand and silt. No mines, prospects, or mineralized areas occur within or near the study area, but some sand and gravel has been removed from alluvial deposits at the east and west sides of the area. Slab lava of marketable grade and quantity was not found in the study area. None of the study area is of current interest for geothermal resources, but the eastern third of the wilderness study area is leased (1984) for oil and gas.

Jan 1, 1987

By T. H. Dubaniewicz

Fiber-optic technology is progressing rapidly, including the development of fiber-optic sensors for many applications. These sensors have the advantages of high sensitivity, light weight, small size, high bandwidth, and freedom from electromagnetic influences. The U.S. Bureau of Mines is investigating the use of fiber-optic technology to monitor mine atmospheres. This report describes a methane monitor based on differential absorption of infrared light. The monitor can detect methane concentrations as low as 0.2 vol pct as far away as 2 km via fiber-optic cable. The upper range is 100 vol pct methane. Since the system requires no electrical power within the mine, it is intrinsically safe.

Jan 1, 2010

By A. Z. Dimitroff, A. C. Moschetti

An improvised rock- dust disseminator, consisting of a 10-gallon galvanized metal milk can that dispenses rock dust in return air currents by the injection of compressed air has reduced the float dust explosion hazards at the Koehler coal mine, Koehler, N. Mex.

Jun 23, 1964

By M. R. Geer

Samples of coal from six beds in the Roslyn-Cle Elum field of Washington were subjected to float-and-sink tests to determine their amenability to the production of high-ash boiler fuel for on-site power generation. Grindability tests and analyses of ash were made. All of the coals would require some degree of cleaning to insure a product of 25 percent ash. With two of the coals the entire size range would have to be washed. With the other four, it would suffice to clean only the coarse coal and bypass the raw fines.

Jan 1, 1965

By J. P. Barkley

"The accompanying tabulation gives the results of a series of operating tests on two types of small stokers. One was an inclined, natural-draft, moving-grate, overfeed ""hand-stoker"" fired and manipulated by hand; the other was. a horizontal, forced-draft, stationary-grate, underfeed, mechanical unit-stoker operated by an electric motor. These were installed as shown by the accompanying sketches (figs. 1 and 2) under horizontal return tubular boilers of a nominal rating of 150 bl.h.p. each.The steam load carried by these boilers was a rather typical heating load. It was fairly constant and of about 30 bl.h.p. throughout the summer months, with small variation between day and night. During the winter months the daily variations were dependent upon the outside temperature. The boilers were banked a considerable part of the night.As noted in the table, two kinds of coal were used. The size of one kind was run-of-mine and the other 11/4 inch nut and clack. These coals from two different mines of the New River district both caked considerably during burning, the nut and slack more than the other. Analyses of the coal were as follows:"

Jun 1, 1929

By E. J. Kloos

The Bureau of Mines devised a new machine-test method for measuring carbon dioxide inspired by a wearer of self-contained breathing apparatus. The new method compares favorably in speed and precision with standard man-tests in which the apparatus is tested while actually worn, and is scheduled for use in future approval tests for facepiece carbon dioxide 'measurements. However, man-tests will still be used to measure the efficiency of the carbon dioxide sorbent materials in closed-circuit breathing apparatus.

Jan 1, 1966

By Michael J. Sapko, Eugene M. Bazala, Eric S. Weiss, Kenneth L. Cashdollar

The data presented in this report are the results, to date, of an ongoing Pittsburgh Research Center Disaster5Prevention research program on the explosion hazards associated with blasting operations in noncoal mines. Laboratory and experimental mine tests have shown that oil shale and sulfide ore dusts can be ignited given the proper predispersed dust concentrations, particle size, and kerogen or sulfur content. Methane (CH) gas may also4be present in deep oil shale formations and can pose a significant added hazard to underground blasting operations. The most common explosive used for blasting in oil shale had been ANFO, a combination of ammonium nitrate and fuel oil; blasting in sulfide ore had used ANFO and/or dynamites. Tests conducted at the cannon gallery at Lake Lynn Laboratory near Fair chance, Fayette County, PA, provided a means of evaluating the relative incendivity characteristics of new and existing explosive products. Three explosives—a pumpable emulsion-ANFO blend, a packaged water gel, and an emulsion blasting agent—exhibited low-incendive qualities compared with other more highly incendive products such as ANFO and some dynamites. Based on the data collected during numerous full-scale blasts in oil shale and sulfide ore mines, the low-incendive products significantly reduced or eliminated the ignition hazards while at the same time providing effective fragmentation of the rock. Based on the positive results from the gallery and field testing, low-incendive explosives, coupled with good blasting procedures, show promise in reducing dust and/or gas ignitions associated with blasting operations in oil shale and sulfide ore mining applications.

By Charles L. Kusik

As part of an effort to establish processes that could be exploited in case of adverse changes in international chromium production and trading patterns, this study was sponsored by the Federal Emergency Management Agency (formerly the Federal Preparedness Agency) through the Bureau of Mines, to experimentally determine the feasibility of recovering chromium from critical scrap metals containing significant quantities of this element. Based on a conceptual pyrometallurgical chromium recovery flowsheet developed at Arthur D. Little, Inc., the experimental program described in this report demonstrated key process steps for the recovery of chromium as ferrochromium in a batch process. The process involves oxidation of chromium into a slag phase, subsequent separation of the slag phase from the remaining metal, followed by reduction of chromium from the slag phase to produce ferrochromium.

Jan 1, 1981

By James L. Hendrix

A study was made of the United States Bureau of Mines' chlorine-oxygen leaching process for complex sulfide concentrates. The investigation sought to determine the kinetic order and IT mechanisms involved in the reactions betweens sphalerite, and galena with chlorine. The influence of copper on the extraction rates was also studied. It has been shown the rates of reaction of chlorine in aqueous solutions with sphalerite and galena are both zero order at 373K with the rate limiting step being the chemical reaction. Addition of cupric chloride increased the extractions of both lead and zinc.

Jan 1, 1980

By J. J. Forbes

The investigation of major and minor coal-mine disasters has been a routine function of the Bureau of Mines since its inception in 1910, and the facts obtained during such investigations have been used as a basis for determining the precautions that the personnel of many mines are observing to prevent similar occurrences, The Bureau has conducted extensive research on roof-control problems, but a comprehensive study of fatal roof-fall accidents was not attempted until February 10, 1950, when the policy of investigating all coal-mine fatalities was approved by Bureau of Mines Director James Boyd. The investigations are being conducted by Federal coal-mine inspectors functioning under the provisions of the Coal Mine Inspection and Investigation Act of May 1941, Public Law 49, and reports covering the investigations are distributed to management, the State mine inspection agency, and representatives of the mine workers organization having jurisdiction at the mine. SCOPE AND PURPOSE OF STUDY This study covers the Federal investigation of 263 of the 315 fatalities from falls of roof, face, or rib that were charged to the bituminous-coal industry during the calender year 1950. The number of roof-fall fatalities investigated is recorded by States in table 1.

Jan 1, 1951

By Forrest T. Moyer

In conjunction -with the statistical survey of the lime industr-.r in 1939, by the Bureau of Hines, producing companies reported the lime-fuel ratios attained in their plants according to type of kiln and kind of fuel. Each ratio, expressed as the number of pounds of lime burned by a unit quantity of fuel, was weighted according to the tonnage of quicklime pro- . duced at the reporting plant and grouped with similar data from other plants, so that an average ratio for each type of fuel and,kiln could be calculated. By this method the variables trat affect ratios of individual plants are more or less equalized, and the computed average lime-fuel ratios provide a fair measure of kiln and fuel efficiencies during 1939.

May 1, 1941

By H. B. Brunot

On April 26, 1949, the Bureau first approved a machine designed to replace the cycle of cutting, blasting, and loading coal by a single operation. This machine took the coal directly from the solid face and delivered it to transportation equipment. By January 1, 1955, 30 approvals for designs of machines of this type had been granted by the Bureau. In the main, this paper describes briefly the action of the various designs approved as permissible. In addition, the approval number, the date of approval, the voltage of the power supply, the number and character of the explosion-proof accessory parts, the size of the trailing cable, and the overcurrent protection at the outby end of the trailing cable are given for each design. Since no similar information has been published by the Bureau, it is hoped the material in this paper will be valuable in giving the mining public an organized look at the various machines of this nature that have been approved as permissible by the Bureau.

Jan 1, 1956

By Richard C. Ballance

Fly ash from four sources and in certain proportions was shown to assist chemical coagulation of turbid water and settling of chemically induced floc. Fly ash reduced the time required to form the first visible floc, promoted more uniform flocs about 2 mm in diameter, and increased the mean settling rate of floc particles. Also, the addition of fly ash produced denser sludges than those obtained with alum alone. Final turbidities were independent of fly ash particle size and carbon content. Optimum proportions of fly ash additive are given.

Jan 1, 1966

By S. Don Brown

Between 1987 and 1988, the Bureau of Mines studied the mineral resources of the White River National Forest and part of the Arapaho National Forest to appraise the resources present and to determine the types of deposits, and their location, that could be mined economically if sufficient demand and metal prices existed. The study included a comprehensive literature search and a limited amount of field investigation of minerals and mining activity in and near the Forest. This report summarizes a more comprehensive minerals report on the Forests prepared by the Bureau of Mines and was written for a general audience without a background in geology or related fields. Mineral resource information indicates that in the Gore Range-the area between Tennessee Pass and Gilman may contain large base-and precious-metal deposits, and could be the focus of exploration activity in the near future. The Breckenridge mining district was found to have a moderate to high likelihood for mineral exploration and possible development of gold. Recent exploration and minor development work has occurred in several other areas: Montezuma, Kokomo-Tenmile, and Upper Blue River districts, and portions of the Sawatch Range.

Jan 1, 1990

By Robert M. Becker

The evaluation of existing rock stresses from measurements of the change in diameter of a borehole that is stress relieved by overcoring has become a common practice, The stress evaluation has been generally based ,on isotropic relations whereas rock in varying degrees is anisotropic. A plane elasticity solution for a circular hole along one axis of an orthotropic medium is adapted for evaluation of in situ stress from borehole deformation measurements. A consistent triaxial testing approach for determining elastic properties of the overcore is also outlined. Comparison of isotropic with anisotropic interpretations of the state of stress show that large errors in evaluation may occur if the anisotropic character of the rock is neglected.

Jan 1, 1967

By Robert B. Fulton

Summary of data and estimates for 52 fluorspar properties in the following 13 foreign countries: Mexico Thailand China (PRC) Morocco Tunisia Italy Spain South Africa France United Kingdom Kenya Namibia Federal Republic of Germany Data includes deposit type, resource tonnage and grades, mining and beneficiation methods, annual production, fluorspar products and by-products, manpower requirements, capital and operating cost estimates. For operating properties, engineering and cost data have been developed for present and anticipated levels of production. Hypothetical operations have been assumed for undeveloped deposits.

Jan 1, 1984

By John J. Mulligan

The Bureau of Mines sampled a gold-bearing schist series 50 miles east of Nome near Bluff, a dormant mining camp on the southern shore of the Seward Peninsula, Alaska. Gold is unevenly distributed through a section of a schist series that extends from the coast northward 4,500 feet. In this section the schists dip westward 20 to 38 degrees and have an outcrop width of about 1,000 feet and a normal width of about 500 feet. An intensely fractured zone within the schists averages 0.015 to 0.017 ounce of gold and 0.03 to 0.05 ounce of silver per ton for outcrop widths of 200 to almost 500 feet. The grade of the remainder of the schist series ranges downward to scant traces. Gold eroded from these schists collected in solution channels in metalimestones to form the Daniels Creek placers, which also extend from the beach southward under the sea for an unknown distance. The lode sources of the gold placers elsewhere in the southern Seward Peninsula may be similar schists that occupy a similar position in the metasedimentary series.

Jan 1, 1971

By H. A. Tucker

This Bureau of Mines investigation was conducted to determine the appropriate quantities of rare-earth methals (REM) in the form of silicides to add to an alloy steel for the purpose of increasing toughness and ductility. The work was conducted in a vacuum induction furnace with the rare-earth additions required to deoxidize and desulfurize a simulated basic oxygen furnace (BOF) vacuum-degassed steel initially containing 0.013 to 0.016 percent sulfur. The product proved to be as good or better than the best basic electric furnace steel of the same composition made by the steel industry. Twenty-three experimental heats of 5 Ni-Cr-Mo-V steel were made, cast into 50-1b ingots, and hot-worked in a press and a rolling mill to ½ inch plates which were then heat-treated to 130/150 ksi4 yield strength. Impact and tension tests showed that the addition of 0.025 to 0.100 percent, or ½ to 2 lb per ton, respectively, of rare-earth metals when compounded with silicon were appropriate for increasing toughness and ductility. These quantities resulted in retained cerium contents between 0.014 to 0.025 percent, and increased the Charpy V-notch energy absorption and the percent reduction of area significantly as compared with base heats at the same sulfur content levels. All the test heats, including those with additions of REH of as much as 4 lb/ton, had greater Charpy V-notch energy absorption values than the base composition could have developed at the starting sulfur range of 0.013-0.016 wt pct.

Jan 1, 1968