Search Documents

By J. E. Pahlman

The Bureau of Mines performed research on a fluid-bed magnetic roasting process for nonmagnetic taconites that utilizes low-rank coals and lignites as reductants and fuels. Roasting tests on a Michigan nonmagnetic taconite were conducted at 600° to 725° C with lignite or subbituminous coal as reductants. Partial combustion of the reductant reduced the amount of heat externally applied to the reactor to maintain the desired reactor temperature. Cleaned, dried reactor top gases were recycled to recover a portion of the reducing potential in these gases without adversely affecting concentrate grade and iron recovery. Highest iron recoveries for magnetic concentrates were obtained at a roast temperature of 650° C with lignite and at a roast temperature of 725° C with subbituminous coal. Magnetic concentrates were obtained that were comparable with commercial concentrates.

Jan 1, 1976

By M. M. Barr

Rapid expansion of the titanium-metal industry focused attention upon ilmenite as a possible substitute for the more expensive and less abundant rutile in producing titanium tetrachloride. Most of the rutile available for this use is imported. Preliminary studies were undertaken to determine the chlorination characteristics of high-titanium slags produced by electric-arc furnace smelting of alluvial Idaho ilmenite at the Federal Bureau of Mines Northwest Electrodevelopment Experiment Station, Albany, Oreg. Low silicon, calcium, and aluminum contents of the slags enhanced their potential value for chlorination.

Jan 1, 1958

By S. E. Khalafalla

The Bureau of Mines investigated variations in the activation energy for the carbon monoxide reduction of magnetite and ferrous oxide with respect to the state of aggregation of the oxide material. Reduction phenomena can only be satisfactorily explained by including an adsorption step in the reduction process. Summation of the values of the exothermic heat of chemisorption and the variable apparent activation energy for reduction yields a nearly constant value of about 50 kcal for either ferrous oxide or magnetite regardless of whether they are aggregated in pelletized form or coarsely crystalline particles.

Jan 1, 1965

By C. R. Bopp, N. A. C. Smith

"For a period of several years, beginning with 1915, there has been a continuous change in the quality of motor gasoline. The average volatility has decreased, this to the fact that higher boiling fractions of the crude oil have been included in the gasoline. This change in quality was made necessary by the tremendous increase in the demand for motor fuel, caused by the development of the motor car, and during the war was an absolute necessity to avoid gasoline shortages. The Bureau of Mines has kept in close touch with this situation by making surveys from time to time of the gasolines sold throughout the country, as this information is of value to manufacturers and users of motor cars and also indicates when any changes are required in the Government specifications. The Bureau has just completed a gasoline survey and is in a position to make public the fact that there has been very little change in the quality of motor gasoline in recent months.During the period from January 17 to February 3, 1920, 81 samples of actor gasoline were collected by representatives of the Bureau of Mines in seven districts of the United States. The cities selected for this survey were New York, N. Y., including Brooklyn; Washington, D. C.; Pittsburgh, Pa.; Chicago, Ill.; New Orleans, La.; Salt Lake City, Utah; and San Francisco, Cal., including Berkeley. In every case the samples collected were taken in such a manner as to represent material actually being sold as motor fuel, and to include samples from each refinery marketing in the district."

Jan 1, 1920

By David F. Gearhart, Thomas M. Barczak

This U.S. Bureau of Mines report examines the roof and floor contact pressure provided by the interaction of a shield with the surrounding strata. Controlled forces were applied to an 800-ton two-leg shield in the Bureau's mine roof simulator; the distribution of forces acting on the canopy and base of the shield were measured with 24 hydraulic pressure cells. Several influential factors that affect the load distribution were investigated: (1) the magnitude of loading (leg pressure); (2) the profile of the canopy, principally the upward-sloping tip; (3) the base-lifting device; (4) horizontal load acting on the shield; and (9 compliancy of the immediate roof and floor. It was concluded that the shield does not develop full canopy or base contact without deformation of the strata. Maximum contact pressures are developed at the rear of the canopy and on the toes of the base. Less than 10 pct of the available shield capacity is developed at the canopy tip despite the design intention to ensure tip contact. Horizontal loading reduced the toe pressure acting on the base by as much as 75 pct. The base-lifting device exaggerated the inherently high toe loading, increasing the contact pressure by more than 200 pct.

Jan 1, 1992

By R. D. Van Zant

The method for smelting zinc in horizontal retorts developed several centuries ago is still in use. This process consists essentially of the reduction of zinc oxide by carbon at 1,200° to 1,400° C. in a fire-clay retort. The reaction is highly endothermic, and a high radiation loss occurs in transferring the heat of reaction through the fire-clay walls. In recent years, silicon carbide retorts with much better heat-transfer characteristics than fire clay have been supplanting the old retorts. The practical impossibility of recovering the carbon monoxide formed in the reduction causes a large loss of fuel. Intermittent smelting is done in small retorts that are manually charged and discharged, and the furnace crews must be specially trained if efficient results are to be obtained. During the past 20 years several processes have been introduced that have substantially improved the horizontal-retort process. One of these, developed by the New Jersey Zinc Co., consists of a continuous process in which a briquetted mixture of zinc sinter, reducing agent, and binder is coked at 750° to 900° C. and charged into a vertical silicon carbide retort. A supply of displacement air or exhaust combustion gas is introduced at the base of the retort at an appropriate pressure in order to keep the zinc vapor from condensing on the cooled residue in the lower part of the retort. Any .oxidizing constituents in the displacement gas are converted to carbon monoxide by reaction with the carbon in the charge. The spent residue is continuously removed at the bottom of tl1e retort. The chief advantages of this process are said to be increased output per man-day, improved working conditions, high recovery of zinc, increased thermal efficiency, and long retort life.

Jan 1, 1950

By Phillip N. Yasnowsky

This Bureau of Mines report examines the percentage depletion allowance rate structure in relation to several criteria that are indicative of U.S. mineral import dependence. These criteria are the minerals considered as strategic and critical for stockpiling purposes, the ratio of reserves to forecast cumulative demand (1976-2000) for selected minerals, and the U.S. net import reliance as a percentage of apparent consumption (1978), also for selected minerals in general, it was Found that there does exist a direct, although not perfect, relationship between the percentage depletion allowance rates and the degree of import dependence as indicated by these three criteria. The higher percentage rates tend to he associated with those minerals for which the United States is, or will likely he, heavily dependent on foreign sources. In addition, a basic discussion of the mineral depletion allowance is provided, including numerical examples illustrating the computation of the allowance under several assumptions. Also, the percentage depletion allowance rates for individual minerals are tabulated.

Jan 1, 1980

By P. M. Sullivan

This report describes a new application of electroamalgam metallurgy in recovering all the zinc as refined metal from galvanizers' sal skimmings. Pure zinc was recovered by electrolysis of skimmings leach liquors in amalgam cells. The following information was gained as a result of literature studies and subsequent laboratory investigations. 1. Reports in the literature indicate that pure zinc can be recovered from chloride solutions with the aid of amalgam cells. From Europe it was reported that amalgam cells could be used to recover pure zinc and chlorine from leach liquor obtained from pyrite cinders following a chloridizing roast.

Jan 1, 1956

By A. Z. Dimitroff

An improvised rock- dust disseminator, consisting of a 10-gallon galvanized metal milk can that dispenses rock dust in return air currents by the injection of compressed air has reduced the float dust explosion hazards at the Koehler coal mine, Koehler, N. Mex.

Jan 1, 1965

By Denise A. Herzog

The U.S. Bureau of Mines conducted a study of cyanide leach technology used in Alaska's mineral industry from 1987 through 1990. Literature and cost data were obtained for mines in the contiguous United States, Canada, and Alaska that use cyanide to recover gold and silver. The data was compiled in an effort to evaluate the economics and conditions associated with cyanide use in Alaska. This report discusses heap leaching methodology and evaluates a "typical" heap leach operation in Nevada and compares the results of the Nevada operation to an analogous hypothetical mine in Interior Alaska. Five daily tonnage rates were analyzed for both the Nevada and the Alaska operations to evaluate the spectrum of economic possibilities. The discounted cash flow rate of return (DCFROR) for each production rate was then evaluated in terms of recoverable metal value (RMV). The Nevada RMV for each production rate was then compared with its Alaskan counterpart, and the results averaged. The Alaskan production costs are an average of 1.71 times greater than costs associated with mining in Nevada at a 0% DCFROR. At 15% DCFROR, costs in Alaska are 2.01 times greater than those in Nevada. Costs are higher in Alaska because of the shorter leaching season, increased labor and transportation costs, and heavier precipitation and vegetation.

Jan 1, 1991

By L. C. IlsLey

[The service given by a flame safety lame is twofold: It provides a safe light and it gives evidence of the condition of the mine atmosphere relative to the presence of methane and the deficiency of oxygen. Since the development of portable electric mine lamps, flame safety lamps are little used for lighting but their use as detectors is as extensive and important as ever. A flame safety lamp in the hands of a trained user will definitely show methane concentrations as low as 1 percent, which in well below the lower explosive limit of methane and air. However, this does not always suffice, especially when making studies of mine ventilation, where it may be desireable to detect concentrations below 1/2 of 1 percent.]

Jan 1, 1936

By Walter D. Holland

LFE Environmental performed an Industrial Hygiene survey of the Paraho Oil Shale Mining and Processing facility in Anvil Points near Rifle, Colorado, on August 6 and 7, 1975. This survey consisted of an investigation of the underground operations for diesel emission contaminants and of the above ground work areas for all inhalation contaminants other than silica dust. Samples were collected to investigate the following contaminants: respirable dust, total dust, NO2, NO, H2SO4, formaldehyde, CO2, S02 and CO. None of the determinations of contaminants in the underground operations indicate air concentrations exceeding their standards. The results for the samples collected above ground indicate only one operation where the employee's exposure exceeds the standards. It is a welding operation where the standards for total dust and lead are exceeded. Since the survey the employer has installed an exhaust ventilation system which has significantly reduced the welder's exposure.

Jan 1, 1976

By Stephen A. Swan

Bureau of Mines researchers have collected and evaluated rollover protective structures (ROPS) f or more than 10 yr. ROPS and falling object protective structures (FOPS) are required on specified mining machines under regulations of the Mine Health and Safety Administration (MSHA). Both ROPS and FOPS are required on mining machines used in surface coal mines and surface areas of underground coal mines (30 CFR 77.403 and 7 7.4 13a), and ROPS are required on mining machines used in metal and nonmetal mining operations (30 CFR 55, 56, and 57.9-88). This illustrated manual provides mine safety personnel, MSHA inspectors, and original-equipment manufacturers with guidelines and a check- list for inspecting ROPS being used in the field. The manual discusses specific requirements of the MSHA regulations and minimum inspection and maintenance checks for ensuring compliance with those regulations. An easily reproducible checklist is provided as an aid to the inspection of ROPS.

Jan 1, 1985

By R. E. Lindstrom

Separation efficiency of a 4 percent divinylbenzene (DVB) resin is not altered over a wide range in temperature. A 12 percent DVB resin, however, exhibits a marked sensitivity to temperature. When flow rates are high at ordinary temperatures, 4 percent DVB resin exhibits higher efficiency, but at 200° F. both resins are equal in performance. Effective separation of rare-earth mixtures may be obtained with hydrogen as a retaining ion by maintaining column temperatures above the solubility of ethylenediaminetetraacetic acid (EDTA) in the free acid form. Slightly lower separation characteristics were obtained with this method as compared with copper as a retaining ion, Recovery of 99 percent of the EDTA from spent eluting solutions that contain copper has been accomplished by a calcium-copper displacement reaction followed by EDTA precipitation. Impurities in the product are correspondingly low. Recoveries of EDTA from holmium solutions with sulfuric acid are substantial; however, those from yttrium solutions are quite modest. Radiotracer experiments show the presence of approximately 0.1 percent yttrium contamina¬tion in the recovered material. The study presented is one phase of a broad research program designed to assist the technology of separating and purifying rare-earth elements.

Jan 1, 1961

By W. D. Bensema, J. W. Adams, W. W. Scott, H. Dobroski

Measurements of the absolute value of electromagnetic noise and attenuation along a hoist rope were made in an operating hard-rock mine, Lucky Friday Mine, located near Wallace, Idaho. Spectra of electromagnetic noise generated by various pieces of equipment, spectra of specific noise signals at various depths, and noise and attenuation on the 4250 foot (1295 meter) hoist, were measured. Three techniques were used to make the measurements. First, noise was measured over the en- tire electromagnetic spectrum of interest for brief time periods. Data were recorded using broadband analog magnetic tape for later transformation to spectral plots. Second, noise amplitudes were recorded at several discrete frequencies for a sufficient amount of time to provide data for amplitude probability distributions. A third technique gave attenuation data through the direct measurement of field strength at various depths. The specific measured results are given in a number of spectral plots, amplitude probability distribution plots and amplitude curves as a function of depth.

Jan 10, 1974

By L. C. IlsLey

The service given by a flame safety lame is twofold: It provides a safe light and it gives evidence of the condition of the mine atmosphere relative to the presence of methane and the deficiency of oxygen. Since the development of portable electric mine lamps, flame safety lamps are little used for lighting,but their use as detectors is as extensive and important as ever. A flame safety lamp in the hands of a trained user will definitely how methane concentrations as low as 1 percent, which in well below the lower explosive limit of methane and air. However, this does not always suffice, especially when making studies of mine ventilation, where it may be desireable to detect concentrations below 1/2 of 1 percent.

Jan 1, 1936

By I. S. Solet

This study, of the liquidus temperatures and densities of molten alloys of zinc and aluminum was made as part of a broader investigation on refining of scrap aluminum. One of the methods of refining involves the separation of liquid and solid phases by gravity segregation and by filtration. More accurate data were required on the liquidus temperatures and the densities of molten' mixtures of the metals than were available in the technical literature. New data on the liquidus curve were obtained by thermal analysis. The new temperatures are, for the most part) somewhat higher than those reported previously by other investigators. The density of molten mixtures of zinc and aluminum were found to be less than would be calculated by assuming that the two metals occupy the same respective molal volumes in solution as they do as pure metals.

Jan 1, 1949

By L. C. IlsLey

Cooperation between the United States Bureau of Mines and the Safety in Mines Research Board of Great Britain, continuous since 1924, has made possible this and other papers on safety subjects. Grateful acknowledgment is made to representatives of the Board for their assistance in arranging visits to several mine safety stations, and to F. R. Wynne, Deputy Chief Inspector of Mines, for arranging visits to mines in Great Britain and other countries in Europe. During the summer of 1927 the writer had the privilege of visiting the mine safety testing stations in great Britain, Belgium, Germany, and France, in the order named. All of these countries have large coal mines, many of which are rated as gassy. Therefore, when the installation of electrical equipment is contemplated, each of these countries is confronted with the same safety problem as is the United States - the development of electrical equipment that will not ignite gassy atmospheres which through neglect or accident might surround the equipment. The means employed by these countries in safeguarding gassy mines should therefore be of general interest to safety engineers in American coal mines, and it is proposed to give a brief survey for each of the four countries mentioned. The third of these surveys covers conditions in Germany.

Jan 1, 1929

By Margaret R. Egan

The U.S. Bureau of Mines conducted experiments in the intermediate-scale fire tunnel to assess the influence of air velocity on the gas production and smoke characteristics during smoldering and flaming combustion of Pittsburgh seam coal and its impact on the detection of the combustion products. On-line determinations of mass and number of smoke particles, light transmission, and various gas concentrations were made. From these experimental values, generation rates, heat-release rates, production constants, particle sizes, obscuration rates, and optical densities were calculated. Ventilation has a direct effect on fire detection and development. The results indicate that, in general, increased air velocity lengthened the onset of smoke and flaming ignition, increased the fire intensity, but decreased the gas and smoke concentrations. Increased air velocity also lengthened the response times of all the fire sensors tested. Rapid and reliable detector response at this most crucial stage of fire development can increase the possibility that appropriate miner response (fire suppression tactics or evacuation) can be completed before toxic smoke spreads throughout the mine.

Jan 1, 2010

By M. M. Fine

This report presents the results of laboratory mineral-dressing investigations by the Bureau of Mines of 14 individual or composite character samples from deposits in the Batesville manganese district. It will be noted that some concentrates have met or approached analytical specifications for metallurgical manganese ore although great variations in both physical and chemical composition from once deposit to another make each a new problem. In most cases it is evident that a substantial loss of manganese has occurred in the various slime and tailing products. An important aspect of this work is the research being conducted on manganese-bearing limestones. Recent reconnaissance indicates that this resource constitutes one of the major domestic reserves of manganese. Laboratory study has shown that ferrograde concentrates can be recovered from samples of manganese-bearing limestones from two properties. Research on samples from other areas is still underway.

Jan 1, 1957