Search Documents

By W. L. Acherman

The Bureau of Mines found the chemical and galvanic corrosion behavior of the TZM and molybdenum-30 tungsten alloys to be generally equal or superior to that of unalloyed molybdenum in many aqueous solutions of acids, bases, and salts. Notable exceptions occurred in 1 [N] nitric acid, where both alloys corroded appreciably faster than molybdenum. In mercuric chloride solutions, the TZM alloy was susceptible to a type of crevice corrosion which was not due to differential aeration. The alloys were usually not adversely affected by con-tact with dissimilar metals in galvanic couple experiments, but the dissimilar metals sometimes corroded galvanically. Both alloys were resistant to substitute ocean water spray at 60° C.

Jan 1, 1968

By N. H. Coates

As part of a joint program of the U.S. Atomic Energy Commission and the Federal Bureau of Mines for using nuclear energy to supply process heat, the Bureau designed and constructed a pilot-scale simulated nuclear reactor system. Although workable components were developed,5 the simulated nuclear reactor could not be operated continuously at its design conditions of 2,500°F. and 250 p.s.i.g. because the refractory materials used for insulation deteriorated. Replacement of these materials with porous carbon permitted sustained operation at design conditions, and a 1,000-hour demonstration run was completed successfully. No serious operating difficulties developed during the test. Leakage of helium after 1,000 hours was only 3 to 4 std. c.f.h. Inspection after the run revealed no damage to any of the components. Including earlier runs during previous research5 the system has been operated about 4,000 hours, of which 1,120 hours have been at 2,500° F. or higher. The helium-recycle compressor performed satisfactorily with no main¬tenance whatever for 2,445 hours, with about 2,000 hours at 900° to 1,000° F.

Jan 1, 1961

By B. K. Cantrell, K. L. Rubow

"The US Bureau of Mines and the University of Minnesota have developed design and performance criteria for a personal diesel exhaust aerosol sampler for underground coal mines. These are based on the premise that size can be used to separate diesel exhaust aerosol, which is mostly submicron in size, from coal dust aerosol, which is mostly greater than a micron in size. The sampler has three stages: a respirable aerosol preclassifier, a 0.8-um aerodynamic diameter inertial impactor to collect mineral dust and a final filter to collect the diesel aerosol. Using a sample flow rate of 2 L/min and gravimetric analysis to within 0.1 mg, the measure sub-0.8 um diesel aerosol has an a-priori limit of detection of 0.3 mg/m3.A miner working in an underground coal mine with diesel equipment is exposed to a wide array of pollutants from the diesel exhaust. These include CO, CO2. NO, NO2, SO2, diesel exhaust aerosol, and a variety of hydrocarbon compounds. A quantitative definition of the health risk resulting from these exposures remains elusive. During the past several years, though, progress has been made in defining the problem.Results from epidemiological studies by Garshick et al. (1988 ), animal inhalation studies by Mauderly eta). (1986), Iwai et al. (1986), and Brightwell et al. (1986) and in vitro studies by Lewtas et al. (1986) have provided sufficient data for the National Institute of Occupational Safety and Health (NOSH) to recommend that ""whole diesel exhaust be regarded as a 'potential occupational carcinogen,' as defined in the Cancer Policy of the Occupational Safety and Health Administration"" (NIOSH, 1988). NIOSH further stated that ""though the excess risk of cancer in diesel-exhaust-exposed workers has not been quantitatively estimated, it is logical to assume that reduction in exposure to diesel exhaust in the workplace would reduce the excess risk.""The Mine Safety and Health Administration (MSHA) has also been directed by an advisory committee to establish a diesel exhaust aerosol standard and to establish regulations to minimize exposure to diesel pollutants in underground coal mines (MSHA,1988). Both reports point out the need for development of measurement techniques for respirable diesel aerosol.In the past four years, the US Bureau of Mines (Cantrell,1987 and Cantrell, et al. 1987), in cooperation with Marple, et al. (1986), at the University of Minnesota's Particle TechnologyLaboratory (PTL), have studied the use of size-selective sampling techniques to measure the mass concentration of diesel aerosol in underground coal mines. Results from these studies have been used to develop design and performance criteria for a personal diesel exhaust aerosol sampler for use in underground coal mines.These criteria are based on the premise that size-selectivesampling techniques,can be used to separate diesel exhaust aerosol, which is predominantly submicron in size, from coal dust aerosol, which is mostly greater than a micron in size. In addition to the performance criteria, this paper discusses the laboratory and field test data used to develop the criteria."

Mar 1, 1992

By James N. Bayne

An examination and analysis of Landsat digital data in the monitoring of surface mines in selected counties of South Carolina.

Jan 1, 1979

By Laird Crocker

A goal of the Federal Bureau of Mines is to minimize the undersirable environmental conflicts and impacts associated with mineral processing operations. To help reach this goal the Bureau operated a citrate-process pilot plant for the removal of sulfur dioxide from lead smelter sintering machine waste gases to test the process. The process uses a carboxylate solution such as citric acid to absorb sulfur dioxide from waste gases. The absorbed sulfur dioxide is subsequently reacted with hydrogen sulfide to precipitate sulfur and regenerate the solution for recycle. Nominal capacity of the pilot plant was 1,000 scfm of 0.5 vol-pct sulfur dioxide gas. The pilot plant was operated for over 5,400 hr and produced about 55 net tons of sulfur. The operation demonstrated that (1) 99 pct of the sulfur dioxide could be removed from lead smelter sintering machining waste gases containing from 0.1 to 0.6 vol-pct sulfur dioxide, (2) sulfur precipitation and solution regeneration with hydrogen sulfide in conventional stirred vessels was readily controlled, (3) precipitated sulfur could be continuously recovered as a 99.S-pct-pure product by flotation and melting, and (4) 78 dry-vol-pct hydrogen sulfide gas could be produced from pilot-plant product sulfur, natural gas, and steam.

Jan 1, 1979

By G. Ahnell

Throughout portions of four (4) heavily mined Appalachian states subdivided by the Mine Safety and Health Administration (MSHA) as: District 3 -Northern West Virginia and Maryland; District'" -Southern West Virginia; District 5 -Virginia; and District 6 -Eastern Kentucky, active coal mine waste embankments associated with mechanical and/or chemical coal processing facilities of various levels of coal preparation were inventoried. For each site plant specifications, disposal techniques, embankments' characteristics, and coal source data were accumulated. Mapping at 1: 24, 000 and 1: 250,000 scale and Disposal Site Characterization forms were developed to present the findings. Associated abandoned surface and underground openings near each site were also indicated as well as locational data for each site and the areas environmental conditions - temperature, precipitation and vegetation types. A state-of-the-art review of coal preparation, waste disposal, and alternative uses of coal waste is also included.

Jan 1, 1982

By Richard A. Dick

This Bureau of Mines report describes the evolution of modern-day blasting agent and slurry products and the state of the art of the usage of these products as it exists today. The steadily increasing consumption of blasting agents and slurries at the expense of cartridged high-explosive usage is related. Although safety is not covered in depth, reference is made to pertinent safety literature available. Product formulations, detonation reactions, and detonation products are discussed. Product terminology is defined and the significant differences between the relatively insensitive modern-day dry blasting agents and slurries and cap-sensitive high explosives are described. Blasting agent and slurry properties are discussed, as well as methods of determining and describing these properties, and specific types of products are also discussed with reference to their ingredients,-properties, and field applications. Increasing consumption of slurries, particularly in small-diameter boreholes, and the development of more cap-sensitive varieties of slurries are forecast although dry blasting agents should continue to dominate the market. The consumption of cartridged high explosives will level off or gradually decrease.

Jan 1, 1972

Relatively few longwall mines in the U.S. operate under multiple seam conditions where the two seams are less than 200 ft apart. This paper describes the experience of six that do. These operations are located in PA, WV and UT, and include examples of both undermining and overmining. Some operate above or beneath their own workings, others are in historic mining districts and must contend with abandoned mines that are decades old. The lessons that these mines have learned cover a broad range of topics, including: • Whether to stack gateroads or place them under old gob areas; • How to size pillars and select artificial support to cross longwall stop lines; • How to use yield pillars to minimize multiple seam stresses and coal bump potential, and; • When to anticipate the creation of pathways for gas, water, or oxygen between current and abandoned gobs.

By L. F. Heising

This report is a general summary of pertinent data on the manufacture and use of synthetic ammonia products. It provides a condensed summary of the potentialities of a synthetic ammonia industry in North Dakota for Federal, State, and private organizations that may be interested in helping to develop an integrates synthetic ammonia and fertilizer industry. The report contains discussions of: (1) Materials used in the manufacture of nitrogenous fertilizers, nitric acid, and urea; (2) National production, imports, exports, and consumption; (3) the ammonia industry, location, capacity of plants; (4) processes used in manufacturing synthetic ammonia, nitric acid, and urea; (5) other potential industries; and (6) analyses of manufaturing and plant cosh;. Additional information on industrial compounds from ammonia and plant nutrients removed by crops is given in Appendixes 1 and 2. Synthetic ammonia is one of the primary ingredients in fertilizers. Resources required in synthetic ammonia manufacture are available in North Dakota. Hydrogen is available from the petroleum and natural gas resources, particularly in the Williston Basin, and from the large lignite resources in the State. Hydrogen can be produced from lignite by a gasification process developed by the Bureau of Mines at Grand Forks, N. Dak.

Jan 1, 1954

By M. Dattilo

The U.S. Bureau of Mines has been conducting research on the use of waste-derived zinc as a partial replacement for pure zinc in the electrogalvanizing process. The end product of this process is automotive sheet, which has enhanced cosmetic protection over previously used cold-rolled (CR) steel. In this study, primer-coated specimens of CR and electrogalvanized (EG) steel were subjected to the on-vehicle environment and monitored periodically by electrochemical impedance spectroscopy (EIS) during immersion in 1M NaCI solution. The results of these tests were compared with immersion-only conditions. Scanning electron microscope (SEM) and energy-dispersive X-ray (EDX) techniques were also used to evaluate the corrosion processes and compare them with atmospheric exposure specimens. EIS was found to measure the corrosion associated with on-vehicle exposure, thus providing an excellent screening technique for evaluation of the performance of EG automotive sheet steel.

Jan 1, 1990

By Keith G. Wallace

Coal mine ventilation systems are often subject to high leakage rates. As a result, changes in airflow resistance will strongly affect the efficiency with which air is delivered to the working place. One major source of airflow resistance is the line brattice used to direct air from the last open crosscut to the working face. Because it is a great distance from the fan, the resistance of the line brattice can result in more overall leakage than an equivalent resistance closer to the fan. Substituting auxiliary fans for brattice eliminates this source of resistance, with improvements in system efficiency and cost. Also, in some mines, the leakage that leads to spontaneous combustion can be reduced. The benefits obtained by several different brattice and fan substitutions have been studied by Mine Ventilation Services, Inc., Lafayette, CA, under contract to the U.S. Bureau of Mines. Changes in main fan duty were compared with additional costs associated with auxiliary fans. Results indicate that in some circumstances, considerable leakage reductions and cost savings are possible.

Jan 1, 1990

By Warren M. Mahan

A rotary kiln process was developed by the Federal Bureau of Mines to produce consistently an iron product containing 3 to 7 percent nickel. Cuban laterite and serpentine ores were smelted in a gas-fired batch-rotary kiln) 5 feet in diameter and 9 feet long. The metal contained 2 to 4 percent carbon, with little or no silicon, and could be produced on a large scale with modest capital investment. A total of 121 tests was run using this procedure. The tests were conducted with a maximum temperature of 2,625° F., using linings of firebrick containing 40 to 70 percent alumina. Slags in the kiln were acid to neutral. The material in each batch passed through three stages: (1) Sponge metal, (2) carburization, and (3) balling and meltdown. Half the tests were made while firing the kiln with atmospheric-temperature air; the remainder were fired with preheated air. Tests showed that preheated air decreased fuel requirements, dust losses, and reducing agent, and increased the capacity of the kiln.

Jan 1, 1960

By Robert J. Hundhausen, Robert M. Gammell

"INTRODUCTION Several mining properties in the Pine Creek area of the Coeur d'Alene mining region of Idaho were examined by engineers 3/ of the Bureau of Mines in 1942. As a result, a broad program of exploration was recommended for the area, particularly in the eastern end, where chances for the discovery of new ore shoots seemed favorable. This report describes the work done and the factual information obtained by the Bureau of lanes.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell Be Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch,. C. C. Ralston, chief, analyzes samples and performs beneficiation tests.The exploratory work at the Sidney mine was part of the activities of the Albany Division of the Mining Branch, S. H. Lorain, chief. Field work was under the direction of R. M. Gammell.Chemical analyses included in this report were performed at Reno, Nov., under the direction of A. C. Rice, acting engineer in charge, Rare and Precious Metals Experiment Station, Bureau of Mines. The ore-dressing tests were made under the direction of S. R. Zimmerley at the Bureau of Mines laboratory in Salt Lake City, Utah.The cooperation and assistance given by the owners of the Sidney Mining Co. is gratefully acknowledged."

Feb 1, 1948

By T. C. Green

A two-phase program evaluated commercial proximity warning devices and then served to design and develop an automatic electrostatic field strength measurement device with improved performance. The Phase I program consisted of test and evaluation of three commercial proximity warning devices, all of which operate on the principle of electrostatic field intensity measurement for determining proximity to high voltage power lines. Performance testing of these devices utilized full-scale cranes and power line systems and a scale model facility. The evaluation results were reported in the Phase I report entitled "Evaluation of Proximity Warning Devices" dated 22 February 1980. Under the Phase II program, a microproressor-based data acquisition system was designed and developed to collect and measure field strength at distributed points around the crane boom. This unit (referred to as the Distributed Sensor AC Electrometer) measures the field strength about a crane boom using 17 distributed sensors. Keyboard control is provided for the equipment operator. Measured field strength values are displayed on a line printer and recorded on magnetic tape. Laboratory testing of this unit demonstrated performance characteristics and field strength measurement accuracy within the design goals. A Phase III measurements program is proposed using the AC Electrometer to map the field strength contours about power line configurations.

Jan 1, 1981

The general nature of the special constructional features that are required to provide safety from explosion hazards on machines approved as permissible by the Bureau of Mines is fairly well known to mining men who are at all interested in safety. These requirements are outlined in the schedules under the provisions of which the investigations of such machines are conducted. Also, the method of conducting inspections and tests of such machines has been described in Bureau of Mines Bulletin 305, Inspection and Testing of Mine Type Electrical Equipment for Permissibility, published in 1929. A more detailed knowledge of the special safety features of a particular machine is often useful and sometimes essential for inspectors, safety engineers, maintenance men, and engineers in selecting machines for a particular application. Three bulletins that give information of this nature have been-published by the bureau, viz., Bulletin 313, Permissible Storage-Battery Locomotives and Power Trucks. Bulletin 343, Permissible Coal-Handling Equipment. Bulletin 382, Permissible Coal-Cutting Equipment. Report of Investigations 3309, Permissible Electrically Operated Air Compressors, which contains similar information, was issued in August 1936, and a Report of Investigations 3326, Permissible Electrically Operated Room Hoists, was issued in January 1937. Thus, the present paper is the third to give detailed information concerning permissible machines of types not included in bulletins, and covers all the rock-dust distributors approved prior to October 1, 1936.

Jan 1, 1937

By F. Chen, L. J. Gaydos, L. M. Demers, D. C. Kuhn, S. C. Sun

"In this report, we demonstrate that NF-KB, a ubiquitous transcription factor, plays an essential role in silica-induced inflammatory mediator production in the mouse macrophage cell line RAW 264.7. Compared to the effect of lipopolysaccharide (LPS), silica mediated a stronger activation of NF-KB p50/p50 homodimer at early phase of poststimulation. Furthermore, activation of NF-xB by silica and LPS appears to be mediated by different signal transduction pathways. Both silica and LPS increased mRNA expression in these cells for cyclooxygenase II, inducible nitric oxide synthase, tumor necrosis factor-a and interleukin- I a. This expression was attenuated along with the inhibition of NF-KB activation. It is well documented that exposure of alveolar macrophages to silica can initiate excessive production of inflammatory mediators and cytokines from several early response genes (1-3). At the DNA level, a common structural characteristic of these genes is the presence of one to five NF-lCB binding sequences (KB) in the 5'-flanking region (4-6). In resting cells, NF-KB is retained in the cytoplasm in an inactive form by binding to inhibitory protein known as hcBcx, hcB~. p 105 (precursor of p50) and p 100 (precursor of p52) (7-9). Upon cellular stimulation, these inhibitory proteins are proteolytically degraded or processed by certain proteases, which allows the liberated NF-KB to translocate into the nucleus as an activated form to initiate or regulate early response gene transcription by binding to its consensus element (GGGRNNYYCC)(7).In this report, we demonstrate that silica can efficiently induce NF-lCB activation in RAW 264.7 cells, and that silica displays different characteristic from LPS in the activation of NF-KB, both with respect to NF-KB subtype composition and the signal transduction pathway that leads to the activation of NF-KB. In addition, abrogation of NF-KB activation by inhibiting the protease can dramatically reduce the mRNA expression of cyclooxygenase II, inducible nitric oxide synthase, tumor necrosis factor-ex (TNF-o.) and interleukin-lex (IL-lex). These findings strongly suggest that NF-KB plays an essential role in silica-induced inflammatory mediator production in the monocyte/ macrophage cells."

Dec 1, 1996

By R. P. Maloney

Since mining operations began in 1900, Government geologists and mining men have periodically recorded the presence of the minerals of mercury and antimony in the extensive gold placer deposits near Flat in the Iditarod district of the Yukon River region, Alaska. No serious effort was made to recover the cinnabar contained in the gold placer gravels, and there is no evidence that veins of cinnabar and stibnite exposed in the placer operations (as reported by the Geological Survey) were ever explored or developed. A large monzonitic intrusive, which is the dominant geologic feature of the immediate area, is believed to be the lode source of the valuable minerals in the placer deposits. In contact with the monzonite are argillite and quartzite, metamorphic products from the Cretaceous shales and sandstones.

Jan 1, 1962

By M. A. Trevits, J. E. Urosek, A. C. Smith, M. P. Valoski

The National Institute for Occupational Safety and Health (NIOSH), in partnership with the Mine Safety and Health Administration (MSHA), is conducting research to test, evaluate, improve or modify coal mine fire-fighting strategies and methodologies through large-scale tests. Since wood is the second most abundant fuel available during a coal mine fire, it was decided that series of large-scale wood crib fire tests were needed to measure the products of combustion and to observe the capability of commonly available direct application fire suppression equipment, namely, fire extinguishers, water and gas-enhanced foam. This paper discusses the wood crib fire tests, provides insight into the products of combustion and describes observations made during the application of the fire suppression agents.

By Thomas E. Marshall, Michael Dunn, L. J. Prosser, Anthony T. Iannacchione

During the past few years, the Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) examined and characterized conditions at a majority of the underground stone mines in the United States. Observations at these mines revealed a limited degree of roof monitoring beyond visual inspection and sounding. When monitors are used, they typically require the miner to measure movement at the roof. If conditions are unstable, the mine rmay be in a hazardous situation while recording data. Based on this scenario, researchers surmised that a simple, inexpensive monitor with the capability of recording data at a distance from the mine roof would be a safer way to gain the information. Additionally, more widespread use of monitors could potentially lead to better understanding of roof movement in general. A monitor to meet this need was designed, tested, and subsequently improved as experience was gained in its’ use at a number of underground stone mines. The Roof Monitoring Safety System (RMSS) can provide an initial indication of movement in roof beams. By understanding and measuring roof movement in underground mines, the potential for injuries and fatalities to mine workers from falls of ground can be reduced. Also, officials at a mine with a history of data are better prepared to make a decision on remedial actions in the event of ground falls. This paper will outline the evolution of the RMSS and how it can be used in a comprehensive proactive ground control safety program. Also included is a case history describing how the RMSS was used in an evaluation of the effectiveness of a mechanical impact scaling machine at an operating limestone mine.

By H. A. Dierks

Implementation of the joint Federal-State control program established in 1955 to cope with the mine water problem in the Pennsylvania anthracite region is described in this report. The increasing severity of the water problem in the anthracite mines has necessitated major adjustments as this continuing program has progressed. Since 1941 the Federal Government has recognized the mine water problem as an important factor in the worsening economic condition of the anthracite region by initiating scientific and technologic investigations and establishing the Anthracite Flood-Prevention Section in the Bureau of Mines in 1948. On the basis of comprehensive investigations and studies, the results of which were published in numerous reports and bulletins, the Anthracite Mine Drainage Commission of the Commonwealth of Pennsylvania formulated a plan that served as a background for legislative action in 1955, resulting in Public Law 162, 84th Congress (Act of July 15, 1955 (69 Stat. 352; 30 U.S.C. 571-576)), for the Federal Government, and Act No. 82 of the General Assembly, July 7, 1955, for the Commonwealth of Pennsylvania. The report covers 29 mine flood control projects approved and executed in implementing the aforementioned legislative acts. Essential engineering and cost details for each project are given, together with an evaluation of the effect that the installed facilities have on alleviating the mine water problem as it concerns individual mines and the anthracite industry as a whole.

Jan 1, 1962