Search Documents

By A. V. Hooker, E. J. Coggeshall

"The Bureau of Mines for some time advocated the firing of all blasts in coal mines as single shots, and this method of firing is the general practice in American bituminous-coal mines. All single shots can be fired with permissible single-shot units so designed that they will not ignite mixtures of methane and air.If several shots in a face are fired singly it is necessary to return the face after each shot. In some mines having steeply pitching coal seams, this may be dangerous or even impossible, under these conditions shots are usually fired simultaneously.Several shots cannot be fixed simultaneously with permissible single-shot blasting units, and safe types of multiple shots blasters are not readily available. This means that the firing of multiple shots in gassy mines is usually accompanied by the possibility of gas ignition as the blast occurs.Tests have been made at the Pittsburgh Experiment Station to determine the possibility of developing safe types of multiple-shot units suitable for such use, or of applying other type safely in gassy sections of mines where firing shots singly is impracticable.The tests may be divided into the following four groups:1. Tests to demonstrate hazard in the use of existing types of multiple-shot units of the portable generator type.2. Tests to show the electrical characteristics of multiple-shot generator units relative to the possibility of preventing igniting sparks and of modifying the design and application of such units in furthering safety."

Mar 1, 1935

By John E. Miller

Absolute viscosity values for gases usually are determined with a capillary tube viscosimeter, One of the correction factors applied to the experimental data is that for nonuniformity of the capillary bore. This report contains useful analytic expressions of the nonuniformity correction for the following cases: ellipse, cone, sine wave, sawtooth wave, square wave, and the general case. The methods herein described are applied to estimate the nonuniformity of a section of stainless steel capillary tubing to be used at the Bureau of Mines Helium Research Center. Several other examples are given to illustrate the usefulness of the present results.

Jan 1, 1967

By Donald M. Hausen

Diamond-bit performance and cost data accumulated by the Bureau of Mines in core-drilling schists reveal significant trends of economic interest. Low-quality, small-size drill bort were the most economical. The percentage of core recovery, type and size of bit, and bit matrix are also correlated with bit performance and costs. Detailed analyses of the factors affecting diamond-bit performances and costs are assessed in the tables, graphs, and discussion.

Jan 1, 1956

By Alla D. Mah

Thermodynamic calculations for antimony and its compounds have been hampered by the lack of adequate basic thermal data; much work rains even to fill the more important gaps. This paper supplies heat and free energy of formation values at 298.15° K, for the sesquioxide and tetroxide, based upon new measurements conducted by the Bureau of Mines. The heats of formation were obtained by combustion (bomb) calorimetry, and the free energies of formation were obtained by combination of heat and entropy data. The new values are believed to substantially improve the accuracy of thermodynsunic considerations involving these oxides.

Jan 1, 1962

By Katherine Harding

This Bureau of Mines publication describes a practical approach to sampling that does not require elaborate statistical techniques. Simple steps are given for finding a cutoff point in the response from a repetitive survey. This procedure can be used to estimate the aggregate value of the characteristic being measured without waiting for a complete count from the survey. This is a useful technique when the reference periods are repeated at frequent intervals, such as monthly and quarterly, and when the statistical collecting agency is engaged in publishing timely data which must be accurate economic indicators.

Jan 1, 1971

By R. J. Henry

This paper describing the mining practices at the Teck-Hughes mines at Kirkland Lake, Ontario, is one of a series being prepared by the United States Bureau of Mines on mining practices, methods, and costs in various mining districts. HISTORY Prospecting was begun in the neighborhood of Kirkland Lake in 1906, but staking did not take place until 1911. Gold-bearing veins were discovered by surface trenching in 1913 on the mining claims which now make up the Teck-Hughes Gold Mines (Ltd.). A small mill was erected in 1916 after the completion of some underground exploration. A transmission' line was built in 1917 to the camp to provide adequate power for a vigorous underground campaign. Also in 1917 the present management took control operations since 1916 have been continuous,' with a steady increase in production to date.

Jan 1, 1930

By L. Allan White

Instrumental analysis is an indispensable tool to many phases of research on rare-earth metals and their compounds; therefore, the development of new and improved instrumental techniques is essential. This report describes an emission spectrometric analytical method using direct-current carbon-arc excitation of various rare-earth-oxide mixtures. Lanthanum oxide serves the dual purpose of an internal standard and a constant major constituent. The versatility of the method was demonstrated by three different applications: (a) Analysis of complex rare-earth concentrates; (b) determination of impurities in high-purity rare-earth oxides; and (c) detection of rare-earth elements in other types of matrices, such as those resulting from beneficiation of rare-earth ores. The average error of analysis in the concentration range of 0.2 to 10.0 percent was 14.6 percent for a group of complex synthetic mixtures of rare-earth oxides. An average error of analysis in the concentration range of 0.05 to 0.50 percent was 21 percent for a group of high-purity rare-earth oxides.

Jan 1, 1959

By Donald F. Reed

In its investigation of old, abandoned, lead-zinc mines at which records of operations are not available, in 1914 the Bureau of Mines dug surface trenches anti', in 1947 It diamond-drilled three holes at the Albright Farm deposit in Sinking Valley. Some good lead-zinc ore had been extracted from veins in dolomitic limestone during the time of the American Revolution and as late as 1870. Since that time the only activity was sporadic prospecting and developing. Thu Bureau of Mines disclosed two additional veins by surface trenching, but diamond drilling failed to find significant lead-zinc mineralization.

Jan 1, 1949

By E. J. Kloos

This publication lists devices approved jointly by the Secretary of Interior and the Secretary of Health, Education, and Welfare, as of May 24, 1972, under provisions of Section 11.2, Part 11, Subchapter B of Chapter 1, Title 30, Code of Federal Regulations (37 F.R. 6244, March 25, 1972), for use in mines as respiratory protection in oxygen-deficient atmospheres, and in gases, vapors, dusts, fumes, and mists. Included are self-contained breathing apparatus, gas masks, and supplied-air, dust, fume, mist, and chemical-cartridge respirators. Names and addresses of manufacturers appear in the appendix.

Jan 1, 1972

By Thomas R. Bur

Symmetry theory, based on ground work established in the study of single crystals and experimental procedures utilizing ultrasonic pulse velocities of spherical specimens plotted on equal area polar projections, enables the direct identification of a material's elastic symmetry system and the determination of its orientation, as well as the position of the elastic coordinate axes. The method is especially useful for elasticity studies of polycrystalline and amorphous materials for which this knowledge of symmetry is a prerequisite in determining the independent elastic constants. Projections based on theoretically derived velocities are given for a single crystal from each of the major crystallographic symmetry systems except the triclinic. Projections based on experimentally derived velocities are given for one brass and several rock spheres.

Jan 1, 1969

By P. C. Van Natter

Numerous mine fires have resulted in high death tolls and considerable finan¬cial loss during the history of coal mining. In most instances the death toll and financial loss were greater because of inadequate fire-fighting facilities. The information in this report is presented in the hope it may serves as a guide in the selection, placement, and care of fire-protection systems in similar coal mines. The adequacy of fire protection varies according to size of operation, employment, and production. When fires occur on the surface or underground, measures must be applied quickly to prevent incipient fires from spreading. The record of coal-mine fires shows that, in many instances, facilities for combating fires were very meager or were absent. It would be virtually impossible to establish and maintain all the necessary facili¬ties that may be needed to extinguish widespread mine fires, but it is believed that the coal industry can ill afford less than the minimum required by other industries where the time element and avenues of escape are much more favorable.

Jan 1, 1958

By Ned Baker

This report describes the development, construction and testing of a hydrogen-fueled underground mining vehicle. A hydrogen burning engine and a hydride fuel system, both previously developed, were installed on a modified utility vehicle, together with the necessary controls. In tests and in actual use, the vehicle performance in terms of speed, acceleration, and gradeability exceeded that of the standard, unmodified vehicle.

Jan 1, 1985

By John A. Johnson

[Tests were conducted at the Mount Weather testing adit of the Bureau of Mines4/ on the effectiveness of spraying water along the outside of the drill steel as compared with standard wet-drilling practice. The spray equipment used in the tests was designed primarily for the control, in quarries, of dust from dry drilling with solid type drill steel. EQUIPMENT Spray equipment is made in sizes to fit different drill steel but is alike in design, the only difference being in the diameter of the ring and the number of spray holes. The device is made of cast steel and has a coating of Stellite on the inside edge that comes in contact with the drill steel. It looks like a garden spray, except that the spray holes point in only one direction.]

Jan 1, 1939

By Robert G. Bottge

Hard rock mining has grown in importance in the Yukon Territory during the last 10 years while Alaskan hard rock mining has declined. One asbestos deposit in Alaska is dormant, but an asbestos deposit 55 miles to the east in the Yukon Territory is being mined by the Clinton Mine Div., Cassiar Asbestos Corp., Ltd. In this Bureau of Mines report, the economics of mining in the two locations were derived using the Clinton mine as a model. Both deposits were assumed to be of equal size and mined by similar methods. Conventional open pit mining and processing methods were assumed, and capital and operating costs were derived using flowsheets and standard costing methods. The estimated cost for the mine, mill, and support facilities in Alaska was about 30 percent more expensive than that in the Yukon Territory. The higher labor rates in Alaska were the primary contributor to the higher construction costs; freight rates added only slightly to the total costs. Approximately two-thirds of the additional annual costs of operating in Alaska were for wages and fringe benefits. The price required for the Alaskan asbestos fiber was $356.65 per ton compared with $287.44 for Yukon fiber, plus or minus 20 percent. A 12 percent discounted cash flow rate of return, 100 percent equity financing, and a rapid writeoff of assets were assumed.

Jan 1, 1975

By L. W. Kelly

The purpose of this paper is to describe several methods that have been employed in successfully recovering roof bolts in Indiana, Illinois, and western Kentucky coal mines, the States where successful roof-bolt recovery was started. As far as is known, the first bolts were recovered in a mine in western Kentucky in January or February 1951. In April 1951 a meeting was held at that mine to discuss the recovery of roof bolts. The meeting was attended by A. D. Sisk, former Chief, Kentucky Department of Mines and Minerals; and L. W. Kelly, Federal Bureau of Mines; and officials of the coal company. Inasmuch as roof bolting was in its infancy, the thinking regarding roof bolts at that time was on the problem of getting them in, not getting them out; consequently, the thought of recovering them was revolutionary. The subject was discussed at length from all angles, and it was finally agreed that, if certain safeguards were taken, no agency represented at the meeting would oppose the practice. That this decision was sound has been proved, as thou-sands of bolts have been recovered in the Middle West without a lost-time accident. Recovering roof bolts is a simple operation; consequently, no complicated equipment had to be designed or built for this purpose. However, about 5 years ago, officials of the Traux-Traer Coal Co. conceived the idea and constructed a mechanical device for recovering bolts that has been very successful and has been copied widely in this area. This device will be discussed in detail in part II of this paper.

Jan 1, 1958

By H. W. Wainwright

One phase of the research and development work on synthetic liquid fuels conducted by the Bureau of Mines at Morgantown, W. Va. in cooperation with West Virginia University deals with the purification of synthesis gas.2/ Most of the experimental studies on gas purification have been directed toward the removal of organic sulfur from gas, either catalytically or by adsorption with activated carbon. An important part of the purification program has been the development of suitable analytical methods for determining organic sulfur compounds. As the total sulfur content, organic and inorganic, of purified synthesis gas should not exceed 0.1 grain per 100 cubic feet, the need for accurate analytical methods is apparent. It is also apparent that such methods must be rapid if one wishes to evaluate various processes for removing sulfur from gas. The organic sulfur found in most gas produced from coal is usually present as carbon disulfide, carbon oxysulfide, methyl and ethyl mercaptans, and thiophene, with the exception of thiophene, the remaining organic sulfur compounds respond similarly to catalytic treatment and can be removed effectively. Not only does thiophene resist most catalytic treatment, but it poisons some catalysts, rendering them ineffective in removing the other forms of organic sulfur.

Jan 1, 1950

By Raymond M. Stateham

Microseismic noise rates and slope movements were measured in an unstable area along the north wall of the Tripp-Veteran pit, Kennecott Copper Corp., Ruth, Nev. Low-noise, wide-band microseismic geophones were located at various points in the wall, and the change in distance across open fractures, resulting from instability, was determined by repeated measurements between fixed points set on each side of the fractures. The microseismic noise rate increased and decreased with corresponding increases and decreases in the rate at which the fractures opened. The microseismic noise rates and changes in width of the fractures show excellent agreement, and the two types of measurements complement each other in monitoring the progress of pit wall failure.

Jan 1, 1971

By Gary E. Sherman

To aid the U.S. Army Corps of Engineers in their Resource Development Navigation Study of ten existing or proposed port sites in Alaska, the Bureau of Mines examined the potential for mineral development around three Alaska port sites: Iliamna Bay, Kotzebue, and Nome. The mineral deposits near Iliamna Bay include gold, copper, and iron. Development of minerals in this area will require the discovery of new deposits or the definition of additional are reserves at known deposits. The mineral deposits near Kotzebue are primarily gold, copper, coal, lead, and uranium. Based on the character of these deposits, it appears that development of a small-scale mine supplying coal for regional use is the most likely scenario in the near-term. The mineral deposits near Nome are primarily gold and copper. Development of small underground gold mines is possible, however it appears that expanded offshore gold dredging will have the greatest impact on the flow of freight and goods through the Nome port in the near term.

Jan 1, 2011

By E. J. Harris

Data obtained from mine ventilation pressure and quantity surveys are required to accurately diagnose ventilation problems, project future air quantity needs, and to locate conditions adversely affecting the efficiency of a mine ventilation system. A method for making mine ventilation pressure surveys with aneroid altimeters was presented in Bureau of Mines Information Circular 7809, and a description of field calculation technique is presented. This report supplements Information Circular 7809 by developing the information obtained during a mine ventilation pressure survey into a single equation suitable, with appropriate modification, for use with desk-top calculators and digital computers. The equation can be used to calculate the ventilation pres sure from the base station to any underground station, or between any two underground stations, and can be programed for semiautomatic sequential calculation using a desk-top calculator. An example of application to a programed desk-top calculator is provided in the appendix.

Jan 1, 1973

By Ronald D. Hill, Elmore C. Grim

Surface mining drastically alters the ecological characteristics of the area disturbed and in some cases has a decided effect on surrounding areas. Vegetation is removed, topographic features and characteristics are changed, and the original geologic overburden profiles are destroyed. Spoil banks generally are a heterogeneous mixture of rock fragments, rock particles, and soil-sized material derived from the overburden strata. With proper mining techniques, the various strata can be partially or completely segregated. Segregation of over- burden material offers the opportunity to bury the toxic, acid, or salt-pro producing strata under growth supporting material. In some situations, lower strata may have more desirable characteristics than surface material and can be placed near or on the surface. For example, limestone strata appear in some lower overburden profiles that have shale and/or sandstone near the surface. Also, some lower strata have higher nutrient levels that have been leached from the surface. Experience has shown that natural revegetation is a very slow process on strip mined areas. Native vegetation may not be compatible with the environment on the mined areas, for example : 1. Low nutrients in the spoil. 2. Toxic spoils (very acid or highly alkaline ). 3. Surrounding vegetation may be of the climax type and may not have pioneer- or primary-invader-type species present. 4. The seed source may be to far away from the adjacent mined areas. Early attempts to revegetate strip-mined lands with trees also proved to be unsatisfactory as they did not provide the initial ground cover required to stabilize the spoil. Erosion control with trees only may take up to 10 years before the canopies close and an effective cover is established. They are slow to form soil profiles and do not provide effective chemical pollution control until long after planting. A quick growing cover of herbaceous species is necessary to obtain quick stabilization and initial protection against erosion by reducing runoff and rain-drop splash. Vegetative cover will also build up a concentration of organic matter in the soil, which in turn will

Jan 1, 1974