Search Documents

By G. W. Jones, I. Spolan

"INTRODUCTION The operation of internal-combustion engines at high altitudes and the general aspects of combustion processes in rarefied atmospheres have created considerable interest in the problem of ignition and flame propagation at low pressures. Nuckolls, Matson, and Dufour 4/ have published results on the effect of low pressures on the propagation of flame in gasoline vapor-air mixtures in vessels of large capacity. The volumes of their test equipment varied in capacity from 0.425 to 125 cubic feet. Various sources of ignition were employed. These authors found that the explosive range of gasoline vapor in air decreases with decreasing pressure at pressures considerably below atmospheric, until a limiting absolute pressure of about 33 mm. mercury at ordinary temperature is reached, at which point no appreciable flame is propagated.Experiments carried out at the Bureau with natural gas-air mixtures at reduced pressures have shown 5/ that the limits of inflammability are but little affected at reduced pressures down to 175 mm. mercury. As the pressures of natural gas-air mixtures are reduced below atmospheric, the mixtures become more difficult to ignite; however, if a suitable source of ignition is employed, the limits of inflammability are as wide at 175 mm. mercury absolute pressure as they are at atmospheric pressure. In view of these observations with natural gas-air mixtures, it appears important to investigate gasoline vapor-air mixtures for possible similar behavior. For this reason the tests herein described were carried-out."

Oct 1, 1946

By G. E. McElroy

Economic solutions of problems of mine-ventilation improvement can be found by mathematical analyses of alternative methods of procedure, but, in the case of our older bituminous-coal mines, the airway network is usually so complex that mathematical solutions are too tedious to be practical. Recourse usually is made to extremely costly and uncertain trial-and-error procedures with the existing layout and equipment. The resulting errors often prove costly and sometimes create hazardous conditions. Both the economic and safely aspects of alternative methods of ventilation improvement may be rapidly and cheaply investigation with analogue computers. An electrical analogue computer, designed and built especially for analyzing mine-ventilation-distribution problems, has been placed in service by the Bureau of Mines at its Pittsburgh, Pa., Experiment Station. It is a nonlinear, low-voltage, fluid network analyzer of a type developed by Malcolm S. Mcllroy, professor of electrical engineering at Cornell University. It was designed in close coopera¬tion with Professor Mcllroy and built by the Standard Electric Time Co., Springfield, Mass. It is the seventh unit of this type to be placed in service and the first designed for mine airflow problems. The other six were designed for either water- or gas-distribution analyses. Three are much larger and more expensive units. The largest unit has a capacity of 20 sources, 576 mains, and 180 loads, or regulated-flow paths. The Bureau unit has a capacity of 5 sources, 128 mains, and 48 loads.

Jan 1, 1954

By C. S. Compton, T. E. Marshall, D. R. Dolinar, R. Grau, L. J. Prosser, A. T. Iannacchione, D. C. Oyler

Unrecognized roof beam failures resulted in 69% of the falls of ground injuries occurring in underground U.S. stone mines from 1990 to 1996. Field investigations at 45 underground stone mines suggest that excessive beam sag or deflection is the principal unstable roof behavior characteristics associated with miner injuries. Laminated roof structures, common in most underground stone mines, allow the immediate roof to separate into distinct beams. The timely determination of roof beam deflection could provide stone miners with advanced knowledge of potentially hazardous roof. Existing methods to assess roof conditions consist of observational and monitoring techniques. Observational techniques include open drillholes, sounding, wedging, and borescopes. Monitoring techniques include scratch tools, extensometers, telltales, Miners Helpers, and Guardian Angels'. Miners have difficulty utilizing these techniques because roof beams are located an average of 8 m (26.5 ft) above the miner's head in environments that are dark, dusty and noisy and these deflections are measured in millimeters of movement. To help mitigate the potential for falls of ground injuries to underground stone miners, the National Institute for Occupational Safety and Health (NIOSH) has developed the Roof Monitoring Safety System (RMSS) to aid in monitoring dangerous levels of roof beam deflection. If enough site-specific information is collected and placed on highly visible maps, individual mining operations could establish general guidelines for responding to specific roof beam deflection occurrences. This would help in implementing a pro-active, comprehensive roof control plan for reducing falls of ground injuries.

By E. B. Nelson, B. W. Gandrud, B. M. Bird

"The Lewisburg No. 2 mine of the Sloss-Sheffield Steel & Iron Company is located in Jefferson County, Alabama, about 7 miles due north of Birmingham. At this point the coal from the Mary Lee seam when coked in by-product ovens yields an excellent quality of metallurgical coke suitable for use in the iron blast furnace; it is also an excellent steam coal. In mining, all three benches are worked. Coarse impurities are largely gobbed by the miners underground.In addition to giving the data obtained from screen-sizing and float-and-sink tests of a representative sample of the raw coal, this report presents the results of slotted-screen tests to show the proportions of flaky particles in selected sizes, and the results of tests to show how much coal is liberated from impurities by crushing the coarsest sizes. These data have been obtained in connection with an extensive study of coal-washing now being conducted by the U. S. Bureau of Mines and the University of Alabama, with U. cooperation of the different operators of Alabama. As the work progresses other reports will follow containing furtner data on the washability both of the Mary Lee seam and of other seams in Alabama and giving the results obtained in preparing these coals by various methods.Although a great amount of investigative work on the preparation of the Mary Lee scam was previously carried on by the various coal companies of the district, comparatively little of this information has been published. In governmental publications three references have been found. Forbes5 gives a number of sections with proximate and ultimate analyses of face samples taken in the mines. Gandrud and Britton'' show sections of this seam at Flat Creek and New Castle; they also give the specific gravity and ash contents of the partings of coal and impurities. In their paper Yancey and Fraser7 include washability studies and washing data from the Sayreton mine of the Republic Iron & Steel Co."

Jun 1, 1930

By King K. Mak

The objectives of this study are to: (1) Assess current signing regulations and practices; (2) Develop effective signing guidelines; and (3) Evaluate the applicability and appropriateness of the proposed signing guidelines through field demonstration at representative mines. A literature search was conducted to determine the state of the art for signing applicable to surface mine haulage roads as well as survey of existing MHSA regulations and review of MSHA accident records. Nine representative mines were visited to gather information on current signing practices. Preliminary signing guidelines were then developed based on the abovementioned data. Field demonstration of the preliminary signing guidelines was conducted in which signing programs were implemented in two selected mines. Signing requirements were first assessed at each of the two participating mines. Subsequently, the necessary signs were designed, purchased, and installed at the two mines. Evaluation of the signing program as to its adequacy, appropriateness, and effectiveness was solicited from both mine management and operations personnel. Experiences gained from field evaluation were then incorporated into the final signing guidelines as presented in this final report.

Jan 1, 1981

By J. B. Gayle

The removal of coal particles from a slurry by flotation is made possible by the formation of stable aggregates with air bubbles of suitable sizes. The formation of such aggregates is theoretically possible only for certain favorable combinations of the solid-liquid-gas interfacial tensions. Because interfacial tensions involving solid phases are not conveniently measurable, a related variable, the contact angle, frequently is used as a measure of the floatability of various materials. Zero angles indicate nonfloatable substances, and large angles indicate substances having a high degree of floatability. During a study of contact angles for coal and substances related to coal in their similarity of response to various physical and chemical treatments, particularly flotation, carbonization, and oxidation, the reproducibility of replicate determinations taken within a 4-hour period was found to be much better than that for comparable results taken over a longer period of time. Consideration of possible causes for these differences led to an investigation of the effects of temperature variations on contact angles. References to literature revealed only a small amount of information, some of it apparently conflicting. Specifically, Sutherland and Wark4/ found that temperature variations "within limits" did not appreciably influence the angles measured for galena conditioned with potassium ethyl xanthate. On the other hand, McGlashan and McLeod5/ presented preliminary data showing that for sphalerite conditioned with potassium ethyl xanthate the angle is maximum at 25° to 35° C., depending on the pH of the system.

Jan 1, 1960

By D. N. Nilsen

The Bureau of Mines is investigating a method to recover Ni, Cu, and Co from low-grade domestic laterites through reduction roasting, leaching, sol-vent extraction, and electrowinning unit operations. The objective of this research is to develop processing technology that can convert low-grade domestic deposits containing critical metals into national reserves. As a part of this research, a solvent extraction system was investigated for the extraction of nickel and copper, followed by the separation and production of suitable electrolytes. Nickel and copper were coextracted from ammoniacal ammonium sulfate leach liquors (pH~9.5) with LIX 64N extractant in a laboratory-size mixer-settler continuous circuit. Three extraction stages resulted in >99-pct extraction of nickel, substantial copper extraction, and essentially no cobalt extraction from leach liquors. A crowd stage reduced the ammonia loading on the solvent by maximizing nickel loading. Residual ammonia was removed from the loaded solvent with a pH-controlled scrub. Nickel and copper loaded on the solvent were separated by selective stripping. Typical nickel strip circuit operation using electrolyte containing 90 grams per liter (g/l) Ni and 11.9 g/l H2S04 yielded >99.9 pct Ni stripped from the solvent in five stages. The copper loading on the recycled solvent was controlled in a copper strip stage using electrolyte containing 25 g/l Cu and 160 g/l H2S04,

Jan 1, 1981

By Thomas V. Falkie

The new international fact of life that has emerged in the 70's is that foreign energy sources can no longer be considered either reliable or low in price. As a result, the United States is turning its full attention to its domestic energy resources. The figures about proved domestic reserves are often used to reassure us about the Nation's energy future: assuming a 50 percent recovery factor, there are at least 219 billion tons of recoverable bituminous coal and lignite, of which 31 percent is available by surface methods; proved reserves of crude petroleum and natural gas liquids total 34.3 billion barrels and 6.4 billion barrels, respectively. There is also about 4 billion tons of recoverable anthracite coal, a premium low-sulfur fuel of high heating value, which is all but priced out of the market because of the high costs of producing it. Total fossil fuel resources are even larger, although there are no guarantees concerning how much might become usable, and when, and at what cost. The figures, however, are impressive. They include the equivalent of about 200 billion barrels of oil potentially recoverable from high grade oil shale; 100 billion barrels in "heavy oil" deposits; and the equivalent of 25 to 35 billion barrels of oil in domestic deposits of "tar sands," and substantial quantities of conventional oil and gas resources. There is also the prospect of a significant increase in electric power generation

Jan 1, 1975

By Irving Hartmann, John Nagy

"The pressures produced by dust explosions are frequently so great and are developed so rapidly that widespread destruction of manufacturing equipment and buildings results. Experimental data on maximum pressures and rates of pressure rise produced in a closed vessel by numerous metal powders and by dusts used in the plastics industry were published in two previous Bureau of Mines papers.4/5/One means for reducing structural damage is provision in the enclosing walls and/or roof of rapidly opening explosion-relieving devices or relief vents through which the pressure of an incipient dust explosion can be quickly dissipated. The vents can be simply unrestricted or free openings: hinged or pivoted sash which swing outward at a predetermined internal pressure; fixed sash, with light wall anchorages; scored glass panes; light wall panels; monitors or skylights; poppet-type vent closures; paper, metal foil, or other diaphragms that burst at low pressures; pull-out diaphragms, or other similar arrangements.The use of pressure-relief vents is recommended in the dust-explosion codes of the rational Fire Protection Association,6/ and recently a special committee on explosion venting has been organized. However, technical data on which the design and distribution of relief vents can be based are meager. An experimental study on venting grain-dust and cornstarch explosions was made by the Bureau of Chemistry and Soils, United States Department of Agriculture.7/ Tests on cork fines, cinnamon, starch, barley dust, and a phenolic plastic were made in a laboratory-scale (0.1-cubic-foot) apparatus by the engineering department of the Factory Insurance Association.8/ A study on the venting of explosions of acetone-air mixtures was made by the Bureau of Mines.9/The object of the present investigation is to extend the limited knowledge on the effectiveness of pressure-relief vents of different types, shapes, and sizes. The aim is to determine the venting requirements in equipment and structures of various dimensions and shapes for dusts of widely different explosive properties. On the basis of such accumulated information, together with theoretical considerations, it is hoped that ultimately it will be possible to recommend correct venting for most operations in which a dust-explosion hazard exists."

May 1, 1946

By M. R. Geer

The washability examination of a coal establishes the quality of the product that could be prepared by mechanical cleaning, shows how much impurity would have to be eliminated to attain a particular quality of product, indicates what type of cleaning process would be suitable, and tells whether the coal could be cleaned efficiently, The coal-preparation laboratories of the Bureau of Mines make washability examinations of coal for a variety of purposes. Sometimes these examinations are made as an integral part of research conducted on coal-washing problems. Occasionally they are made on coals mined on Government-owned land or on coals destined for use in Government installations. Often they are made on coals from new fields or new beds in existing fields to help establish the characteristics of the Nation's coal reserves. Whatever the original reason for doing the work, the results often are useful later in evaluating deposits or in the design of cleaning plants. Publication of the results of such studies provides for the widest possible usefulness. This report brings together the results of washability examinations made on 1 coal each from Oregon and Idaho, 2 from Wyoming, 5 from Utah, and 11 from Washington. Material of this nature is inherently difficult to summarize. Some of the coals are so clean} despite full-scam mechanical mining, that they could not be improved materially by washing; others present some of the most difficult preparation problems found in the country.

Jan 1, 1961

By G. A. Appell

"INTRODUCTION During the summer of 1945, the Bureau of Mines conducted an investigation and program of churn drilling near the village of Tennyson in Grant County, Wis. The work was undertaken as part of a general investigation of the zinc-producing area of southwestern Wisconsin at a time when all effort was being made to increase the production of metals important to the war program.The area for special investigation was selected on the basis of favorable structural disclosures, evidence of widespread zinc mineralization, absence of any great amount of exploration to depth beneath the productive shallow workings, and the favorable results of several churn-drill holes in the village of Tennyson.During the Bureau's investigation, 30 churn-drill holes aggregating5,888 feet were completed.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to-the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual. Investigative work, and prepares the final report.The work described herein was accomplished under the direct supervision of Francis C. Lincoln and the author, mining engineers of the Bureau of Mines. Final data on the investigation were prepared under the direction of Edward F. Fitzhugh, Jr., chief Minneapolis Division, Mining Branch."

Jun 1, 1947

By Thomas J. Peters

The Lime Creek study area lies 100 air km east of Boise, and 70 air km northeast of Mountain Home, Idaho. The eastern boundary of the 28,000-hectare, east-west-elongate study area lies 0.2 km west of the 3,077-m-high Smoky Dome. The area is mainly underlain by Cretaceous granitoid rocks of the Idaho batholith. No mineral resources were identified, but two mines and one prospect were found in the study area. At the President and the Last Chance mines, in the southwest corner of the study area, gold mineralization occurs along steeply dipping east-northeast-trending faults and associated quartz veins, and within adjacent Cretaceous granitic rock. The mineralized material is not rich enough to mine underground, and near surface, open-pit-mineable deposit areas could not be identified. The third prospect, the Ventura, is within altered pink granite of probable Tertiary age, but metal concentrations are very low. Geothermal activity was not observed within the study area, but hot springs do occur in the Vicinity. Bedrock observed is only suitable for the most basic high bulk and low end value applications, such as crushed aggregate. Numerous sources for crushed stone occur closer to markets. Alluvial concentrate (placer) samples did not contain free gold, and no substantial alluvial bars were seen; deposits were too small to contain resources.

Jan 1, 1993

By A. Adams

The quality of hafnium metal produced by the Kroll process depends upon the purity of the hafnium tetrachloride. This investigation of methods for purification of hafnium tetrachloride was undertaken to aid in producing a higher purity hafnium metal than is currently produced by the Kroll process, The quantities of metallic impurities in hafnium metal were decreased by contact with molten alkali-metal chloride salt. Contact was achieved by a semicontinuous process of bubbling gaseous hafnium tetrachloride through a molten salt bath or by a batch process, first fusing the tetrachloride with a combination of alkali chlorides and then heating the mixture to sublime the hafnium tetrachloride. Low-melting mixtures of sodium, potassium, and lithium chlorides were used to purify hafnium tetrachloride. About 30 percent of the initial hafnium tetrachloride was trapped during purification with alkali- metal chloride salts. The 95-percent confidence limits (6)4 for the amount of oxygen decrease 60 and 34.3 parts per million when the batch purification is combined with a reduction so that both take place in the same equipment,

Jan 1, 1961

By Clete R. Stephan, Mark J. Schultz, William A. Slivensky, Eric S. Weiss, Kenneth W. Jackson

he Pittsburgh Research Center (PRC)~ and the Mine Safety and Health Administration (MSHA) are participating in a research program to evaluate the strength characteristics and air leakage resistance of seals and water trap designs for use in underground coal mines. This program is being conducted at PRC's Lake Lynn Laboratory near Fairchance, Fayette County, PA. Seals designed with a 40-cm-thick polymer (polyurethane) and aggregate core between two dry-stacked (no mortar) concrete block walls (coated on out by sides) withstood a 138-kPa pressure pulse while maintaining acceptable air leakage rates. Similar seal designs utilizing a 97-cm-thick, 91-kg/m7-density, polymer-only core did not survive; however, a 5 1 -cm-thick, 203-kg/mi-density, polymer-only core seal successfully withstood the explosion pressures. Evaluations of cellular concrete seal designs have shown that a two-pour slurry injection technique did not adversely affect the strength of the 1.2-m-thick seals when subjected to a 138-kPa pressure pulse. Two seal designs utilizing low-density cementitious block have also been evaluated with successful results. In addition to seal strength tests, various 15- and 30-cm-diam U-shaped water trap pipes and a water trough design were evaluated under explosion conditions and were shown to be inadequate when evaluated under worst-case conditions. Simple modifications to the various water trap designs were successfu1 in preventing the passage of explosion flame through the trap.

Jan 4, 1996

By W. L. O'Brien, E. A. Rowe

Electrorefined vanadium with additions of up to 5 percent by weight of yttrium, cerium , lanthanum , praseodymium, neodymium, and samarium was melted to ingots in a nonconsumable electrode arc in a helium atmosphere . The ingots were rolled into strips and evaluated for the effect of the alloying elements on hardness , tensile strength , ductility , recrystallization temperature , and microstructure . Except for samarium , average additions of alloying elements of 1 to 2 weight - percent resulted in the retention of 0.12 to 1.05 weight - percent in the alloys and reduced the ultimate tensile strength from about 48,000 to approximately 30,600 psi . The corresponding yield stress (0.2 percent offset ) was reduced from about 40,700 to approximately 20 , 200 psi . Diamond pyramid hardness (DPH) was reduced from 117 to an average of 62 kg /mm² . Increased malleability at room temperature resulted with yttrium and all rare - earth- metal additions , except samarium , particularly with more than 0.25 weight - percent additions . Decreasing oxygen contents corresponded with the changes noted in the mechanical properties of the alloys . The recrystallization temperature of electrorefined vanadium was reduced from approximately 950 ° to 800 ° C. Yttrium or a rare- earth metal content , except samarium , in excess of 0.1 weight - percent in vanadium produced a second phase suggestive of an eutectic which indicated a possible maximum solubility of less than 0.1 weight - percent for both room and elevated temperatures .

Jan 1, 1964

By S. P. Kinney

[The blast-furnace operator is often confronted with the problem of determining the size of the materials which are used in the furnace burden. The statement is heard that the coke is larger or smaller or that certain ore is finer than that previously used. A screen analysis of the materials used gives a measure of the different sizes of materials in an aggregate. When one is fine and the other is coarse, the difference is obvious; but when the materials are of similar sire, it is more difficult to estimate the degree of finances or coarseness. In considering raw materials it would be desirable to be able to judge the size of the radio ideal materials entering the furnace and the burden as a whole, by one representative value, such as the average size of particle. Previous work by Perrott and Kinney3 developed a method for measuring the average size of particle in a mass of finely ground materials, and an attempt will be made to apply this method to the materials included in the blast-furnace charge and to the entire burden.]

Jan 1, 1930

By S. J. Aresco

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash-softening temperature, the free-swelling index, and the Hardgrove grindablity index. Under most of these specification contracts the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions3 issued by the Bureau of Mines; the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor; if it is not, a price adjustment is made. Analyses of the delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous of coal as delivered is a check on the practical results obtained in the coal.

Jan 1, 1967

By R. L. Grant

An investigation was undertaken by the Bureau of Mines to determine the relationship between freespace and ignition probability for borehole shots. A series of experiments was concluded which covered six freespace conditions for a pemissible explosive in a 3/4-inch borehole and encompassed some 700 shots. The results were analyzed statistically. From the analysis of variance, it was concluded that the freespace means were different and that this conclusion is not impaired by possible differences in the explosives used. Within the limitation of this experiment, a definite relationship was found between the freespace and the ignition probability. Specifically, the incendivity increases with increased freespace up to a maximum; beyond this maximum there is some indication of decreasing incendivity. Further investigations are in progress to establish whether the effects of freespace on ignition probability reported here are applicable to the large test gallery, INTRODUCTION A borehole loaded with an explosive charge is a common feature of the routine gallery tests for determining the permissibility of coal-mine explosives, of Experimental Coal-Mine shots, and of the small steel cannon shots used in connection with certain research programs on the ignition of firedamp (6, 10).6/ The question of the interrelationship of freespace, weight of charge, and ignition probability of the methane-air atmosphere has been raised

Jan 1, 1959

Pillars with width-to-height ratios of less than 1.0 are frequently created in underground hard rock mines. The strength of slender pillars can be estimated using empirically developed equations. However, the equations can provide variable results when the width-to-height ratios approach 0.5. This paper investigates some of the issues affecting pillar strength at low width-to-height ratios in hard brittle rock. The investigation includes an evaluation of empirical pillar strength data presented in the literature and observations of pillar performance in underground limestone mines in the eastern United States, supplemented by numerical modeling in which failure processes and sensitivity of slender pillars to variations in rock mass properties are evaluated. The results showed that the strength of slender pillars is more variable than that of wider pillars. The numerical model results demonstrated the increasing role of brittle rock failure in slender pillar strength. The absence of confinement in slender pillars can result in a fully brittle failure process, while wider pillars, fail in a combined brittle and shearing mode. The onset of spalling in slender pillars occurs at or near the ultimate strength, while this is not the case for wider pillars. Slender pillars are shown to be more sensitive to the presence of discontinuities than wider pillars, which can partly explain the increased variability of slender pillar strength. Two examples are presented that illustrate failure initiation by brittle spalling and the sensitivity of slender pillars to the presence of discontinuities.

By W. L. Parker, W. A. Selvig

"Introduction.Powdered or pulverized coal is extensively used as a fuel, the total annual consumption*** in the United States being about 12.000,000 tons, and growing steadily. As the coal is usually pulverized so that 70 per cent or more parses through a 200-mesh sieve, it presents difficulties in sieving, because such finely divided material tends to clog the meshes. A fineness test is desirable in order to judge the efficiency of the pulverizing apparatus, and as an indication of the particle size of the coal being burned.Committee D-5 on Coal and Coke, American Society for Testing Materials, has recognized the desirability' of a standard method for determination of fineness of powdered coal. The Bureau of Mines, in co-operation with this Committee, conducted sieving tests on two standard samples of powdered coal, which are described in this paper. As a result of this work a method for making fineness tests, by band sieving, is recommended as a standard method, while a rapid method, by machine sieving, is given for routine tests.Outline of Investigation.Preliminary trial tests were made by the bureau and tentative methods were formulated for making the sieving tests both by band and by machine.Each of two samples of powdered coal was carefully mixed, and portions were sent to the twelve laboratories mentioned later. These were requested to make duplicate sieving tests on the two standard samples, by the hand-sieving and machine-sieving methods, and to follow the tentative procedure exactly as outlined. All of the laboratories made sieving tests by hand shaking and eight of them made tests by machine shaking."

Nov 1, 1923