Search Documents

By Franklin D. Cooper

This chapter includes tables for 1979 that were not available in time for publication in the 1978-79 Minerals Yearbook, but it does not include corresponding tables for 1980. The value of raw nonfuel mineral output in 1980 was estimated at $24.8 billion, 8.5% above the 1979 value. Of the 21 metal commodities produced, quantitative output increased for 11 and decreased for 10. The values for 10 metals were up, 10 were down, and 1 was unchanged. Among the 47 non-metallic commodities produced, 14 showed quantitative increases, 32 declined, and 1 was unchanged. In terms of value, 32 nonmetallics increased, and 15 declined.

Jan 1, 1981

By John Nagy

This circular has been prepared for the guidance of safety engineers, shot firers, and coal-mine inspectors concerning multiple blasting with short-delay (millisecond-delay) detonators. These special precautions are suggested in addition to those normally followed in blasting, as outlined in the Federal Mine Safety Codes 5 6/ and in Miners' Circular 58.7/ INTRODUCTION The use of short-delay blasting has been proposed for promoting safety and increasing the rate of production in coal mining. Ideally, short-delay blasting, as compared with equivalent single-shot blasting, reduces exposure of the shot firer to dust, fumes, and weakened roof; as compared with equivalent simultaneous blasting, it reduces roof disturbance.

Jan 1, 1959

By W. E. Lamont

Flotation studies of phosphate-bearing waste pond materials, low-grade washer products, and raw ores, all from the Tennessee brown phosphate district, showed that these types of materials could be treated without des liming to recover high-grade phosphate concentrates. The investigation showed that fine grinding before flotation was a requisite for increased recovery of the phosphate values and that the optimum pH conditions were in the range of 10.0 to 10.5 when using anionic collectors. Multiple-cleaning of the rougher phosphate concentrate was required to produce high-grade concentrates. Phosphate recoveries ranged from 60 to 82 percent and were inversely related to the grade of concentrate produced.

Jan 1, 1972

By Wilton Johnson

Native asphalt was produced in 1981 by five companies in three States, Alabama, Texas, and Utah. Texas was the leading State in production of native asphalt. Total production increased in 1981 to 1.26 million tons, while value increased 10.5% to $27.7 million. Bituminous limestone, used primarily for street and road repair, was produced by Whites Uvalde Mines and Uvalde Rock Asphalt Co., both in Uvalde County, Tex., and Southern Stone Co., Colbert County, Ala. Gilsonite was produced by American Gilsonite Co., Uinta County, Utah, and Ziegler Chemical and Mineral Corp., Weber County, Utah. This material was used for purposes other than road repair.

Jan 1, 1982

Cement kiln dust (CKD) is a waste product generated at the rate of 4 to 12 million tons per year in the United States. The dust has considerable resource potential as a neutralizer for coal mine waste effluents and as a lime substitute in the agriculture and construction industries. However, little information has been published on the composition and characteristics of CKD, and a concern arose over the potential environmental effects of the waste when an analysis of a single sample from West Germany revealed lead and zinc concentrations of 5,620 µg/g and 16,200 µg/g, respectively. To assess the hazardous waste potential of CKD,

Jan 1, 1983

By Thomas O. Llewellyn

Laboratory semicontinuous and continuous heavy liquid cyclone separation pilot plant tests were made to determine the feasibility of producing a high-grade kyanite concentrate from a kyanite-quartz rock sample from Graves Mountain, Ga. Use of a three-stage heavy liquid cyclone circuit demonstrated that a 96.4-to 99.0-percent kyanite concentrate could be obtained with recoveries of 95.5 to 96.7 percent. The test work showed that by steam stripping with 6.9 tons of steam per ton of ore and two stages of detergent scrubbing the residual TBE content of kyanite cyclone products was 0.22 pound per ton of ore.

Jan 1, 1971

By Wilbur I. Duvall

Nineteen quarry blasts were instrumented with particle-velocity gages mounted in a uniform soil overburden, back of one face in a quarry in Iowa. Three components of particle velocity, radial, vertical, and transverse, were recorded at each of eight stations back of each blast. Distances from blast area to gage stations ranged from 150 to 3,000 feet. Eleven of the quarry blasts employed millisecond delays, and eight were instantaneous blasts. Charge weight per hole was 200 pounds, and the charge weight per delay interval, including the instantaneous blasts, ranged from 100 to 3,000 pounds. Analysis of the data from these tests shows that the particle velocity, V, produced at distance, D, by a quarry blast of charge per delay interval, W, can be represented by an equation of the form, V=KWb D-n, where b and n are exponents, and K is the intercept constant which is a measure of the level of vibration. The value of K for a millisecond-delayed blast employing one hole per delay interval is about 42 percent larger than the value of K for a single-hole blast. The value of K for a multiple-hole milli-second-delayed blast is about the same as that for an instantaneous blast when the charge per delay for the millisecond blast is equal to the total charge for the instanteneous blast. The vibration level from millisecond-delayed blasts employing one hole per delay is shown to be independent of the length of the delay interval and the number of delay intervals over the range of the variables tested: 9, 17, and 34 milliseconds and 3, 7, and 15 delays per blast.

Jan 1, 1963

By Launa Mallett, Charles Vaught, Michael J. Brnich, R. Lincoln Derick

After thoroughly covering the health and safety training subjects required under Title 30, Part 48, of the Code of Federal Regulations (CFR), mine operators often find themselves with little or no time left in the class schedule for other important topics. This paper discusses a technique developed in partnership with RAG Twenty mile Coal Co., Oak Creek, CO, for incorporating employee participation at all levels in fire prevention and safe equipment operation training outside of traditional classrooms. The process involves development of training modules consisting of short, 5- to 7-minute videotapes coupled with toolbox talks that ground the content of the videos within the context of a miner’s workplace.

Jan 1, 2002

By M. R. Geer, H. F. Yancey

Fuel requirements of the Pacific Northwest have been increased greatly by the war . To the normal peacetime demands for fuel have been added the requirements of new industrial and metallurgical plants engaged in war production , the increased demand arising from expansion of existing industrial establishments , increased amounts of railroad fuel required to handle wartime traffic , and increased quantities of domestic fuel required by the influx of war workers . In the face of these augmented demands for fuel shipments of fuel oil have been curtailed , wood fuel which normally is an important factor in both industrial and domestic markets of the area is less abundant , and the production of coal in Washington has decreased sharply . The fuel requirements of the region have been met so far by shipping large tonnages of coal into the Pacific Northwest from Utah , Wyoming , Montana , and Colorado ; the quantity received from these States and Canada in 1943 amounted to 2,688,9124/ tons , 175 percent of the Washington production . or The proximity of the Washington coal mines to large centers of war production has resulted in widespread migration of miners to employment in shipyards and aircraft plants ; the ensuing shortage of miners largely accounts for the decreased production of coal in the State . Hence , strip mining , which requires relatively few workers and a shorter time for development , offers an attractive means of alleviating the local coal shortage and obviating the necessity of shipping coal from the producing areas of the Rocky Mountain States to the Pacific.coast . So urgent has been the necessity for augmenting local coal production that any coal property that promises to be amenable to strip mining , even though the coal may be inferior in quality , has warranted examination . Even low- grade coals that cannot compete in the normal market can be used locally , thus releasing better coals for shipment to critical centers. of consumption ... One such deposit of low- rank fuel examined by the Bureau of Mines is in western Lewis County , about 9 miles east of Toledo , Wash . The coal is lignitic and on the as - received basis has a heating value of 6,000 to 6,500 B.t.u. per pound . The property is of interest primarily because the physical conditions favor operation by stripping and offer opportunities for low- cost production with very low manpower requirement .

Jan 1, 1945

By Frank E. Federspiel

In 1992, the Bureau of Mines conducted a mineral resource investigation of the 19,200-hectare Garfield Mountain study area in east central Idaho. The area had been proposed for Wilderness. Cretaceous-age quartzite and limestone conglomerates underlie the area's east half; thick travertine beds, as well as limestones, dolomites, sandstones, and volcanic tuffs occupy the west half. All the rocks have been faulted and folded as part of the Western Overthrust Belt. Two, enormous travertine deposits occur in the west end of the study area. The lower deposit, controlled by Faxe Kalk Inc., has at least 200 million m3 (cubic meters) of travertine resources. Most of their deposit is very bright with a high CaC03 content and a low insoluble residual percentage: thus it is suitable for use as a paper and paint filler. The upper deposit, owned by Idaho Travertine Corp., contains 100 million m3 of travertine resources; it is used for facing or dimension stone. Weathered travertine outcrops are buff to tan and locally vuggy. Bureau of Mines samples of' outcrops contained greater than 95% CaC03. Approximately 600 m3 of travertine have been quarried from the two deposits and used for facing stone. Four travertine quarries and two dozer cuts were examined. Faxe Kalk has 103 White Rock placer claims on the lower deposit; approximately one-half of the claims are within the study area. Idaho Travertine has the Limestone 1 and 2 placer claims on the upper deposit. A 4,647-m-deep oil and gas exploratory well was drilled on the east end of the study area without success.

Jan 1, 1993

By Wm. W. Adell

"These hydrocarbons belonging to the same chemical series as methane, having the general formula CnH2n have many chemical properties in common with methane and their addition to a lean gas charges the properties and burning characteristics of the gas in the same general direction although to a different extent. The hydrocarbons of this series do not readily enter into chemical reaction with other substances and therefore are incapable of combining with oxygen or polymerizing in the disturbing system and thus cannot cause gum and room troubles commonly met with in the distribution of manufactured gas.As the number of carbon atoms in the molecule increases, i.e. in proceeding from methane throughout the series, the oxygen requirements for the complete combustion of unit volume of the gases also increases; in other words, the calorific values of these hydrocarbons (as gases) increases from methane. Similarly the specific gravity increases from methane in the same order. In Table 1 are shown some of the physical constants and properties of a few of these hydrocarbons which hive bearing on their use for enriching gas."

Nov 1, 1927

By B. J. Scheiner

Electrooxidation of cinnabar mercury ores (HgS) was investigated as a means of providing an effective and economical hydrometallurgical technique for extraction of mercury from its ores, particularly those too low in grade to allow economical metal recovery by retorting or furnacing techniques. Oxidation was accomplished by electrolysis of ere slurried with brine. Cinnabar was dissolved by oxidation of the insoluble sulfide to soluble mercuric salts. The mercury ion in a brine solution forms a stable tetrachloro complex. Typical laboratory experiments required I to 7 hours of electrolysis at 35-percent pulp density in a brine solution that contained 4 to 20 weight-percent sodium chloride (NaCl). Power consumption ranged from 10 to 50 kwhr/ton of dry ore. Mercury extraction values between 90 and 99 percent were obtained with all of the ores investigated. Subsequent mercury recovery from leach solutions was readily accomplished by precipitation on zinc. Pilot mill experiments in a 100- to 200-lb/hr extraction plant are in progress to quantify power and reagent requirements, and extraction and recovery data obtained to date closely parallel those obtained in the laboratory.

Jan 1, 1970

By Stuart R. Zimmerley, John Gross

"In the study of ball-mill grinding at the Intermountain Experiment Station of the United States Bureau of Mines at Salt Lake City, Utah, it was desirable to measure the work input to a ball mill at the mill itself so that consideration of motor efficiency and transmission losses would be eliminated.The device adopted is essentially that used by Prof. H. E. T. Haultain4 in measuring work input to rolls. The mechanism was changed only so as to adapt it to a ball mill.Figure 1 is a diagrammatic sketch of the apparatus.The pulley which rotates the mill is loose on the mill shaft and is equipped with ball bearings. This pulley is connected by means of three tangential springs to the driving plate, which is solid on the mill shaft. Power applied to the loose pulley is transmitted to the driving plate, and hence to the mill, by the three springs; the greater the resistance of the mill, the greater the spring extension. The extension of the springs is transmitted by the steel extension tape to the differential integrating meter.The integrating meter is operated by two friction wheels in contact with the integrator disk which revolves at a definite ratio of speed to that of the mill. The friction wheels are held in contact with the disk by the spring suspension of the integrator and are connected to a differential gear cage, the revolutions of which are recorded on a counter such as is used in gas meters. Due to the differential gears the c e is stationary when the two friction wheels revolve at the same speed in opposite directions; this condition exists when the integrator is centered on the disk and corresponds to no load or to a zero spring extension. As the lead is applied, the springs extend and move the integrator from the center or zero point, resulting in a difference of speed between the two friction wheels. Due to the revolution of the differential cage this change in. speed is transmitted to the counter. The integrator and extension tape system is kept taut by means of a light spring attached to the integrator, the spring having just enough tension to assure that the integrator returns to zero when the load becomes zero."

Feb 1, 1931

Reduce the noise levels to which operators of double-drum longwall shearers are exposed without compromising the operational effectiveness of the shearer. The Problem Noise produced by double-drum longwall shearers can be harmful to machine operators. Typical noise levels at the lead-drum operator position range from 100 to 105 dBA, and Federal noise regulations allow only one to two hours of exposure per shift at these levels. Noise radiated by the shearer cutting drum is the primary contributor to the overall noise level. However, test of a noise-controlled cutting drum developed by the Bureau of Mines reduced the operator noise level to 95 dBA, thereby increasing the allowable operating time to four hours per shift. Approach The key design aspect of the noise-controlled shearer drum is its reduced vibration-al response to coal-cutting forces. Laboratory studies have shown that these forces are concentrated in the low-frequency region (500 Hz and below). Since the cylindrical core and the cantilevered I plate-like helix of the standard shearer drum are easily excited by these forces (natural vibration frequencies be-

Jan 1, 1985

Design a model health and safety program which, when implemented, can improve mine safety by reducing occupational injuries and accidents. Approach The Bureau of Mines developed a model program which identifies the elements essential to the effectiveness of health and safety programs designed for mining operations, and is readily adaptable to all types of sizes of mines. The model program primarily provides training on loss control and accident investigation and technical assistance with health and safety problems. In order to assess the effectiveness of the program, it was tested at both a coal and gold mining operation. Monthly statistics were generated to reflect the number of occupational injuries and accidents, and the severity of injuries (as measured by the number of work days lost during recovery). Observations were made of employees performing a large number of randomly selected jobs in order to estimate. the proportion of the workforce that was working in the presence of one or more of three types of safety deficiencies: Type A-individual job performance deficiencies which could be corrected by the employee alone I e.g., an employee is seen not wearing a seatbelt.

Jan 1, 1986

Identify specific sources and the relative levels of contribution of various components of longwall shearer operations to the total airborne respirable dust generated during mining. Approach A research investigation was conducted in two phases by the Bureau of Mines at five mine sites to identify specific dust sources and their relative importance during long-wall shearing operations. During phase I of the project the specific longwall mining elements identified for evaluation were: cutting, sumping, tramming, conveying, and moving roof supports. During phase II of the project, two dust sources were evaluated: clearance ring cutters cutting in six-inch web width increments, and loading operations. Investigation Results As a result of dust measurements, the gage cutters were determined to be the major dust-generating source on the shearer. These cutters, at 6-inch web depth, produce three times as much dust per unit volume as is produced at 30 inches full web depth. The following list of averaged values for the mines tested shows that shearer cutting generated averaged dust levels four times as high as those generated by conveying, and approximately five times as high as those generated in moving roof supports.

Jan 1, 1984

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

2. Preliminary Study - Initial Probing 2. 1 Introduction Initial probing of the mine passage is required prior to the emplacement of the sealant material or deployment of the seal checker system. Factors which are of interest in sealing and checking include a. size and condition of the mine passage b. location of the borehole with respect to the ribs c. the presence of water flows d. the proximity to an intersection The importance of each of these factors depends strongly on the sealant material. Because the sealant material had not been selected at the time of the initial probing study, a broad survey of probing techniques was conducted. The capabilities and limitations of each technique as they applied to probing through the borehole were identified. To facilitate this comparitive evaluation, Table I was prepared which lists all passage conditions which might affect the emplacement of sealant material in the passage. The most satisfactory techniques for observing each condition of interest are listed together with the effects of the observation on the sealing operation. Table II summarizes the environmental conditions likely to be encountered in the passage being probed and the physical

Jan 1, 1973

By O. P. Hood

The smoke problem means different things in different places . In the neighborhood of industrial plants , especially smelting plants and cement plants , the term " smoke " is applied to material discharged from these plants , consisting of a mixture of solid particles ( dust ) , fume which has condensed from vapors , and gases of various kinds that are produced in the operations . In the ordinary use of the word , however , " smoke" refers to the visible material which escapes from the burning of coal . White smoke usually owes its color to small drops of water which have condensed from the water vapor that it formed in the burning of coal . When smoke is black, the color is due to unconsumed particles of carbon and usually when the smoke problem is spoken of , it is this black smoke produced in the burning of coal that is referred to , Many inquiries in regard to smoke are addressed to the Bureau of Mines , and the following brief summary has been prepared as covering the usual questions . For references to the smoke problem in England , I am indebted to a recent interesting paper on this topic by David Brownlie .

Feb 1, 1922

By Joan Weinberg

The real gross national product (GNP) advanced at a annual rate of 3.1 % during the second quarter, following a revised 3.4% increase in the first quarter (see table 1). Export growth continues to play an important role in the rising output. Combined with the decline in imports, it resulted in a noticeably improved trade position. Imports of consumer goods, including automobiles and food, fell while exports rose. Imported cars have been losing ground to domestic cars. The foreign car share of the U.S. market fell from 36% in October 1987, to 29% in May 1988. Business spending for new plant and equipment contributed strongly to the GNP increase. Equipment purchases, particularly of computers, rose at a 14.8% annual rate, following a large first-quarter gain. Purchases of structures rose 11.8%. The other key component of business spending, change in business inventories, declined from the first quarter. Inventory buildup in late 1987 had been considered excessive.

Jan 1, 1988

By J. O. Jones

[Willis Mountain in southeastern Buckingham County is one of several kyanite deposits its central Virginia. It is composed principally of kyanite resulting from metamorphism of siliceous sedimentary beds rich in alumina. The mountain, which trends north-south, is 2 miles long and is topped by a narrow ridge with sleep rugged sides rising to an altitude of 1,160 feet and projecting 500 fast shove the surrounding countryside. Bureau Mines engineers examiner Willis Mountain early in 1949, when bonded concentrations of coarsely crystalline kyanite were observed in the kyanite-quartzite on the northern end of the mountain and in loose boulders on the eastern slope. Commencing in late July 1949, the investigations continued on the Long Mountain segment for 11 months, ended in June 1950. A total of 600 samples from 32 diamond-drill holes, aggregating 3,876 feet of drilling, and from 255 feet of sampling in 3 trenches was assayed for kyanite and ferric oxide.]

Jan 1, 1954