Search Documents

By R. J. Heemstra

A method was developed for calibrating photographic emulsions and retrieving working curves for emission spectrography. The values obtained from a digital readout or a recorder chart of a comparator-microphotometer are converted to light intensity values using an emulsion characteristic curve derived from a quartic polynomial preliminary curve. The characteristic curve, consisting of Seidel transform versus the logarithm of intensity, is split into two cubic polynomials at the zero value of the transform, resulting in eight emulsion calibration coefficients. These methods allow use of the calibration curves even at very small and very high intensities, thus extending the range of analysis. Use of a small computer allows rapid calculations. A computer program was written to formulate, code, and file each working curve along with its statistical error. Proper coding of the input data permits the direct printout of the concentration of the elements under investigation.

Jan 1, 1970

By Joseph M. Kurtak

The Bureau of Mines conducted a four year (1985-1988) mineral assessment of the Juneau Mining District in southeast Alaska as part of its ongoing statewide mining district evaluation program. Following an extensive literature search, the Bureau investigated mines, prospects, and mineral occurrences in the area. This report describes the results of Bureau work in the Eagle River area of the Juneau gold belt; a component of the Juneau Mining District comprising 87,000 acres between the Mendenhall Glacier and Berners Bay. Gold and silver have been the only metals having significant production from the area and occur mainly in quartz stringer and fissure type veins hosted by phyllites, greenschists, greenstones, altered diorite dikes and quartz diorite gneiss. Gold also occurs in several small placer deposits. Approximately 21,100 oz of gold and nearly 9,000 oz of silver were produced over a 60 year period. Currently, the only mining activity consists of some exploration and minor placer gold production. Inferred and indicated lode gold resources having mineral development potential total approximately 796,000 tons with a weighted average grade of 0.22 oz/ton gold.

Jan 1, 2011

By J. S. Kennedy, M. M. Fine

"INTRODUCTION Barite is one of the major industrial minerals whose production has increased considerably in the last 10 years. In 1935 domestic production of barite was 218,075 tons and. had increased by 1944 to 515,136 tons. 3/ Most of the primary uses for barite and barite products were developed before 1935, so the increase in barite production reflects the growth of industry in general rather than any recent developments in barite technology.The principal uses for ground and crushed barrite are as a weighting agent in heavy drilling fluids, as a filler in rubber and other materials, as a pigment and extender in paints, and as a flux in glass melt. In addition, a considerable' quantity of barite serves as the raw material for the manufacture of lithopone and barium chemicals.Specifications for barrite vary widely and depend primarily on the use to which the material is put. The primary requisites for barite used in heavy drilling muds -are that it have a minimum specific gravity of 4.2 and be very,low in soluble salts. A minimun barium sulfate content of 92 percent may be specified; but this is less important than the gravity. 4/ In addition before consumption the material must be ground to '92 percent minus 325-mesh. 5/ Lithopone and chemical manufacturers require a minimum of 94 Percent barium sulfate, a maximum of 1.0 percent iron oxide, and not more than a trace of fluorine. 6/ Barite used as fillers in light-colored products should be of fairly high grade, but the filler used in dark products may be considerably lower grade.Glass barite should contain a minimum of 96 percent barium sulfate, not more than 3 percent moisture, a maxium of 0.2 to 0.4 percent iron oxide, and not more than a trace of titanium oxide. Particle size is a matter of some importance in glass barite, also. 7/"

May 1, 1948

By T. J. Ballard

Corundum is a natural alumina (A120 ) and is next to the diamond in hardness . Except for the gem varieties , it is used principally as an abrasive , chiefly in grinding , dressing , and polishing metals and optical glass . Natural corundum is preferred to artificial abrasives for certain specialized jobs . Most of the corundum ( excluding emery ) mined in the United States came from the Corundum Hill mine in North Carolina and the Laurel Creek mine in Georgia . The Corundum Hill mine provided over half of the domestic production of corundum prior to 1900. Since 1900 , the importation of foreign corundum and the manufacture of artificial abrasives caused the decline of corundum mining in the United States .

Mar 1, 1947

By W. W. Roepke

The Bureau of Mines has developed an interactive computer program that enables mine operators and others to identify the effect of cut-ting system changes on relative dustiness at the face. The program, which simultaneously evaluates machine parameters, coal seam parame-ters, and operator-controllable parameters, was developed for use on any microcomputer using BASIC programming language. The program allows the user to change one or more of the cutting system parameters at a time to see how these changes affect relative dustiness. A complete program listing and flowchart are included along with operating in-structions and sample outputs. An example showing how to use the program is also included.

Jan 1, 1985

By John Ward Smith

Aragonite, co-occurring with calcite and dolomite as matrix minerals, has been discovered in Mahogany zone oil shales of Colorado's Eocene Green River Formation, posing puzzles on the geochemical patterns of their separate origins, reasons for their simultaneous existence, and their interrelation. The presence of aragonite is demonstrated by X-ray diffraction. Amounts of aragonite and dolomite are significantly and inversely related, but the calcite quantity is essentially independent of either aragonite or dolomite quantity. A geochemical pattern outlining the deposition conditions that created the Green River Formation oil shale is postulated from characteristics of the oil shale. The development of the three separate carbonates--aragonite, calcite, and dolomite--the inverse relationship between aragonite and dolomite, and the independence of amounts of calcite and the other two carbonates are shown to be natural consequences of this oil-shale genesis pattern.

Jan 1, 1973

By James Paone

This report shows the feasibility of predicting drillability, analytically, by using regression analysis techniques. The approach is new in diamond-drilling research. Further, the study shows that this technique may be of value to drill manufacturers and others in mathematically delineating performance characteristics of new drills in specific rock types. Another application might be the prediction of penetration speeds in extraterrestrial material based on the physical properties of the materials as samples become available. Prediction equations for penetration rates are presented for 9 rocks drilled in the laboratory and for 20 rocks drilled under field conditions. The prediction equations are based on drill operating parameters and on characteristics of the rock penetrated. No single physical property appeared consistently in the best predictor equations, and all the physical properties were found to be highly correlated with each other.

Jan 1, 1966

By Leonard Obert

THE CRACKING AND POPPING of rock, often heard by men working underground, for years has been interpreted as a warning of danger and unstable ground. However, not until 1939 was it discovered that rock under stress generates subaudible and sometimes audible seismic disturbances (referred to as "micro-seismims" 4), which can be detected with the use of a suitable seismic apparatus. Since that date laboratory and field investigations have been in progress to ascertain to what extent this phenomenon can be utilized to detect, localize, and determine the magnitude of areas of instability in and around mine openings and to predict if and when failure will occur. These investigations have included a determination of the types of problems to which the method is applicable and the effect of rock type, geological defects, such as joints, fractures, faults, and other uncontrollable factors, on the reliability of results. Six reports have been prepared covering the investigations conducted between 1940 and 1952 (4-9). 5 These reports describe some of the characteristics of micro-seismims, as determined from both laboratory and field tests; the equipment used to pick up and record micro-seismims; the general test procedure and method of analyzing results; and applications of the method to specific mining problems.

Jan 1, 1957

By L. D. Tracy

"This paper represents work conducted by the Bureau of Mines in cooperation with the Illinois Geological Survey and the Engineering Experiment Station of the University of Illinois.IntroductionThe present report covers conditions and mining royalties in District VIII of the coal fields of Illinois, as designated by the Illinois Geological Survey. The various districts have been described in the reports on the Illinois coal-mining investigations, carried on cooperatively by the Illinois Geological Survey, the engineering experiment station of the University of Illinois, and the U. S. Bureau of Mines. This district includes Vermilion and Edgar Counties, but as the coal-mining operations in Edgar County amounted to only 827 tons in 1923, the data here given have been confined to Vermilion County.A similar report on District VI (Williamson and Franklin Counties) has been issued as Serial 2722 of the Bureau of Minos.A description of geological and mining conditions, and a discussion of market and transportation facilities, have been included because these have an important bearing on the royalties specified and the general conditions of the lease.Mining ConditionsDistrict VIII is better known as the Danville district and in 1923 produced 4,177,000 tons of coal, or approximately L per cent of the total output for the entire State for that year, which was 79,300,000 tons."

Apr 1, 1926

By C. P. Bowie

For years many oil producers have believed that often low-pressure oil- and gas-bearing strata have been over coked in fields where the rotary system of drilling has been used. Collom3/ gave as a reason for this condition that because the mud fluid was thick, the oil or gas stratum was plastered and sealed as the tools passed through it and no oil showed at the surface. Although this observation was made 15 years ago, it may often still be true notwithstanding modern developments in coring and electrical logging. Operators have believed, also, that mud fluid does not solidify behind the casing. Lewis and McMurray4/ stated: "All the evidence obtainable from practical experience points to the fact that the mud fluid properly mixed and employed does not solidify behind the casing, even in deer wells and after long periods."

Jan 1, 1937

By Stephan Stecura

One of the principal objectives of the Bureau of Mines program for development of superrefractory ceramic materials is to obtain fundamental data on the physical properties of refractory oxides. Elements of particular interest to research workers in the Bureau include groups III and IV of the Periodic Table and the rare-earth group. This report contains thermal expansion and phase inversion measurements on oxides of scandium, yttrium, lanthanum and 12 lanthanide series elements (promethium and terbium omitted) up to 1,350°C, made by high-temperature X-ray diffractometer techniques. Thermal expansion values were calculated from unit cell dimensions measured at selected temperatures; with anisotropic oxides expansion was determined parallel to each major crystallographic axis. The combined random and systematic errors in the thermal expansion values are considered to be less than 3 percent of the total expansion at 500° C, and approximately 2 percent at 1,000° C, No difference in expansion coefficients was observed between heating and cooling cycles for oxides that did not undergo phase inversion. Tabular data of linear expansion, in percent, linear expansion coefficients, and graphical presentation of linear expansion as a function of temperature are presented.

Jan 1, 1961

By J. Hyvarinen, A. D. Look

"INTRODUCTION AND SUMMARYElectricity is used extensively in open-pit metal mines to provide illumination, heat, and power to operate hauling and loading equipment, drills, pumps, signal systems, and other machinery. Good installation and maintenance of equipment and power, circuits, are essential to minimize the hazards of shock, burns, and fire.In the 13 years from 1931 to 1943, 20 fatal and 82 nonfatal injuries resulted from the use of electricity in open-pit mines in the United States ; 4/ these figures represent about, 10 percent of all fatalities and 1 percent of the nonfatal injuries. The ratio of fatal to nonfatal injuries from electricity in such mines was very high during this period; the figures show one fatality to every five accidents from this cause.Electricity may cause personal injury through abnormalities in equipment, such as short-circuit, accidental ground, overload, and poor contact; however, each year some fatal electrical accidents are due to persons touching uninsulated ""live wires."" These contact injuries are the result of careless body movements of persons in the vicinity of 'wires at places not normally frequented, or of accidental contact with live circuits when handling metal objects. Electrical hazards can be minimized by the enclosure or elevation of current-carrying parts; ample working space around equipment, adequate insulation, locking switches in the open or closed position under certain conditions, identifying and warning devices, protective grounding, insulating flooring, platforms, or rubber gloves, and proper inspection and maintenance."

Apr 1, 1949

This manual provides instructions for installling, operating, and maintaining protective canopies on the Joy Mfg. Co. cutter. These instructions are based upon two actual installations: one made in a mine and one in the factory. The parts list and engineering drawings for the protective canopies are included at the end of the manual. And a discussion of some alternative design concepts is also included. The manual can also be used for retrofitting other cutters with similar protective canopies. Skilled mechanics can determine if the instructions herein would be applicable to the other cutters and can determine any necessary modifications if they are not.

Jan 1, 1973

By Rogers F. Davis

This publication has been prepared to supply manufacturers and industrial users a listing of mobile diesel-powered equipment and subassemblies approved and certified by the Bureau of Mines for use in nongassy noncoal mines and tunnels. This revised and supplemented listing supersedes an earlier publication2 released in 1963. Testing of diesel-powered equipment is one phase of the Bureau's program of health and safety that concerns approval of electrical and diesel equipment designed to prevent explosions, fires, shocks, or toxic hazards in underground mines, when such equipment is used and maintained properly. Manufacturers submit machinery and component parts to the Bureau for study of their design, safety features, and use. Equipment must pass exacting tests and must meet strict requirements established through research and experience and outlined in the Bureau's permissible schedules before the Bureau approves it for safe use in mines.

Jan 1, 1968

By W. C. Holliman

This report on the characteristics of commercial aviation gasolines presents compilations of inspection test data furnished on their products by manufacturers of commercial grades of aviation gasoline, and special data obtained in Bureau of Mines laboratories on samples of these gasolines. Data and physical samples for the survey were submitted by 15 manufacturers on 18 grade 80, 21 grade 91/98, 22 grade 100/130, and 10 grade 115/145 aviation fuels.

Jan 1, 1948

By J. H. East, D. Harrington

Fires in metal mines have resulted in some of the worst disasters in American mining history insofar as loss of life is concerned. One fire caused the death of 163 miners and individual less spectacular fires have cost the lives of scores of workers. Metal mines are often very deep, and the men working on numerous levels far removed from direct communication with the surface. In many instances they cannot be warned quickly of an emergency or a mine fire by telephone or other usual method of communication, or by messenger, flashing lights, gongs, sirens, or whistles. Telephones are not paricularly effective as a means of warning unless placed at all strategic points and with attendants always on duty; though telephones well placed have a definite value in any well-pla.mied emergency procedure in mines of all kinds. Messengers are slow and men working in remote parts of a mine would not receive a warning quickly enough. Most metal mines are not electrically lighted, except at or adjacent to shaft stations and in principal haulageways, and this limits the effectiveness of flashing lights. Electric gongs and sirens or whistles have been tried as warning signals, but the sound is quickly deadened and does not travel upward into the stopes, especially those of an extensive volume. Shutting off the compressed air is by no means satisfactory as a warning, as not infrequently it is stopped accidently, so that it loses its value as an alarm. The introduction of water into compressed air lines is undesirable as a fire warning and necessitates considerable care, especially in deep mines; pressure-reducing valves must be provided to reduce pressure that otherwise would break connections or split the pipe. A quick, effective method of warning miners underground of the existence of an emergency requiring them to leave the mine immediately, such as a fire on the surface or underground, is provided by the introduction of stenches in the compressed-air lines. This method of warning is by no means experimental, inasmuch as it has been used successfully for many years in

Jul 1, 1943

By John W. Buch

"INTRODUCTION The Ruhr coal basin is estimated to cover an area of more than 1,000 square miles. Here, the total thickness of the coal bearing formation (Carboniferous) is 10,500 feet, and drilling-hole have revealed 92 coal beds with a total thickness of 262 feet. 6/ Beds pitch from 0 to 90 degrees and about 70 percent of the wartime production came from beds that pitched less than 30 decrees. 5/For example at the Minisiter Stein mine, there are 24 minable coal beds ranging from 80 centimeters. (2 ft., 7 1/2 in.) to 250 centimeters (8 2 1/2 in.). The vertical thickness of the measures is 1,000 meters (3,200 ft.), and at this mine the deposits are covered with 150 meters (500 ft.) of surface wash. The cross section (fig, 1) at Fritz mine; Hoesch, A.G., Essen, Ruhr, is characteristic, The mines have been developed and worked to vertical depths of 2,000 to 2,500 feet by vertical shafts; main-level intervals are 500 to 700 feet apart. Haulage roads are straight, driven in rock, and centered as nearly as practical between property boundaries. Levels are sectionalized by driving crosscuts at right angles to the main haulage road on 800- to 900-foot centers. The roads are the main transportation arteries for the use of trolley or Diesel locomotives. A plan of the sixth main level (fig. 2) at the Bruchstrasse mine; Gelsenkirchener A.G., Bochum, illustrates main-level development and,sectionalizing with crosscuts. The cross section in figure 3 is that of the fourth crosscut west at the same mine."

Oct 1, 1946

By Floyd G. Anderson

This report reviews and summarizes information on prevention and suppression of dust in mining, tunneling, and quarrying published in the United States during the years 1958 through 1960. Unpublished pertinent data developed or assembled by the Bureau of Mines during this period also are included. Silicosis statistics reported by the U.S. Public Health Service indicate a sizable silicotic population in the United States and suggest a need for greater dust-control effort. A joint medical-environmental survey was begun by the U.S. Public Health Service and the Bureau of Mines to evaluate the magnitude of the silicosis problem in the metal mining industry in the United States.

Jan 1, 1962

By J. R. Alldredge

This Bureau of Mines report presents a computer code that has been developed for describing and testing the statistical distribution of general continuous data sets. The statistical distributions used include the normal, lognormal, exponential, chi square, gamma, and uniform. Histograms for observed and expected values are plotted for each distribution. An example using geologic data obtained from a study of the geometric properties of natural fractures in oil shale rock illustrates the use of the computer program, GDIST.

Jan 1, 1977

By Donelson A. Robertson

Includes a review of the state-of-the-art of explosives loading in the crushed stone and cement industries of South Florida and the development of a field test program for alternatives. Emphasis is on the loading of small diameter (2 1/4" or less) explosives. Test results ire evaluated for operational and economic feasibility. Details are described of an explosives loading method which involves placing cardboard tubes with external couplings through the hollow drill steel and then Loading explosives into the tube casings after the drill rig has moved off. This method eliminates the hazards peculiar to loading explosives Through the kelly bar. The alternative method can be performed by existing drill rigs with or without minor modification. With modification, improvement in yield per blasthole and/or primary crushing rate provides opportunity so offset some or all of the additional cost.

Jan 1, 1978