Search Documents

By James A. Wasson

This Bureau of Mines report summarizes the application of pilot flooding in the evaluation of a potential waterflood project. Aspects of pilot flooding discussed include choice of pilot location, confined and unconfined waterfloods, operational precautions, and comparison of predicted with observed performance. Summaries of published methods of pilot flood data analysis for determination of full-scale waterflood feasibility are presented and their use illustrated for example pilot flood data.

Jan 1, 1974

By G. E. McElroy

Changes in existing airway and fan-installation conditions offer the most common opportunities for effecting economical operation of mine ventilating systems, but the largest possibilities for securing this result lie in the original design of the main airways for efficient service. Formulas, and. charts for their graphical solution, are presented herewith for the determination of the elements of airways design when the conditions of service are known, or may be roughly approximated. Although the analyses are made with particular reference to metal-mine airways, there is no essential difference between metal and coal mine main airways, and the methods presented are equally applicable to both. Little attention is paid to designing airways for maximum economy in the ventilation of metal mines. Most of the openings used as main airways are originally designed and used for transportation and other operating purposes. Even where openings are made primarily for ventilation, the possibility of their future use for other operating purposes, or even custom alone, usually results in the selection of a size and shape similar to those of existing openings. Natural conditions, such as heavy ground, often seriously limit the size of opening that can be maintained without excessive expense; and various operating factors, such as velocity limitations on traveling roads, often dictate size requirements in excess of those required for economy in ventilation only. In metal mines the main airways are, as a rule, too small rather than too large for economic service, with the general result that the quantities in circulation are often less than the mine's proper requirements over long periods, even though excessive amounts of power are applied in an effort to remedy conditions.

Jan 1, 1932

By B. W. Haynes

With the national focus on energy, the combustible fraction of urban refuse is being extensively considered as a fuel supplement for coal in the generation of heat and power. The objective of these analytical studies by the Bureau of Mines was to determine the concentration of major, minor, and trace elements in the combustible fractions collected at various locations in the Bureau's urban refuse recycling pilot plant located at College Park, Md. The samples processed through the plant were submitted by various municipalities that are considering resource recovery as an alternative to landfill or other means of disposal. Twenty-five elements were determined in samples from six geographic areas and were compared with element concentrations found in typical coal samples.

Jan 1, 1977

By Richard A. Allwes

The Bureau of Mines conducted an in-mine case study on two consecutive three-entry gate road systems designed in accordance with the stiff-yield pillar design concept. This Bureau study was conducted in order to further develop technology that will improve the health and safety aspects of longwall mining. Support loading and strata activity were monitored to determine the effects of retreat longwall mining on the gate road ground control system. Analyses of pillar stress and roof bolt loading histories revealed that headgate roof support elements ex-perienced cumulative loading throughout the life of the longwall panel. Tailgate pillar loadings had significantly different histories from the loading histories of the headgate pillars. Stress relief occurred in the tailgate pillars following the passage of the longwall face. More-over, the stiff-yield pillar design, with the abutment pillar placed adjacent to the working panel when part of the headgate system, provided effective ground control in that no major roof falls or roof problems were experienced in the headgate or tailgate systems during longwall mining.

Jan 1, 1985

By H. Kenworthy

The objective of this investigation was to evaluate the technical feasibility of smelting certain low-grade domestic iron ores in an electric furnace. Laboratory-scale experiments showed that a high recovery of iron in the form of pig iron can be obtained from east Texas ores containing less than 25 percent iron. The pig iron was amenable to standard-or electric-furnace-refining methods for producing steel. Car-bon, silicon, and phosphorus were the primary impurities removed in refining. Overall recoveries of iron as pig iron exceeded 95 percent, in contrast with commercial mineral-dressing recoveries on these particular ores of 50 percent of the iron as a 45-to 50-percent iron concentrate.

Jan 1, 1958

By Donald P. Schlick

The Federal Coal Mine Health and Safety Act of 1969 requires each mine operator to implement the respirable dust sampling program established by the Secretary of the Interior and the Secretary of Health, Education, and Welfare. This program requires frequent sampling of "high-risk" face workers and periodic sampling of other underground workers. Dust samples are collected by the coal mine operator and weighed at the Bureau's Pittsburgh Field Health Group, and the results are processed by the Bureau's Automatic Data Processing Section located in Denver, Colo. This paper presents the system employed by the Bureau to weigh the dust samples and to process and store the data.

Jan 1, 1971

By C. J. Walker

The ever-increasing use off natural underground formations for storing natural gas has focused attention on the behavior of such storage formations under varying operating conditions. The need for a means of evaluating in¬dividual wells and groups of wells has become manifest. It is essential that industry and others be able to determine the rates of flow that can be ex¬pected from a given well or group of wells under different conditions and to ascertain whether certain wells are deteriorating. Such questions need more exact answers now than ever before because of the vital role underground gas storage plays in the industrial and domestic consumption of natural gas. The Bureau of Mines--in cooperation with the American Gas Association--has main¬tained an active interest in gas-well testing because of the implications of such test procedures on the consumption and efficient production of natural gas. A basis for testing gas wells was provided by the back-pressure method of Rawlins and Schellhardt (12).4/ They showed that for normal gas wells there is a consistent relationship between rates of delivery of gas and corresponding pressures when the formation pressures are used as the basis of interpretation, The equation for this relationship is as follows: Q = C (Pf2 - Ps2)n where; Q = rate of flow, generally expressed in cubic feet per 24 hours. C = a coefficient.

Jan 1, 1960

By Edward A. McClatchie

A methane monitor that complies with 30CFR75.313 has been designed and fabricated using a novel pressure modulated infrared absorption technique. The methane monitor met or exceeded in performance all of its target specifications. The monitor was operated continuously during production mining for the entire duration (45 days) of the in-mine test; no failures occurred during the test. The monitor was regularly checked with calibration gas and no shifts in calibration were found during the in-mine test. Operating principles, performance data and electrical schematics are included in the report.

Jan 1, 1976

By Lloyd A. Morley

Previous research conducted for the USBM by Penn State personnel (Grant GO-101729) found that a need existed to physically model a typical a-c/d-c coal mine section electrical system. Its purpose would be to permit preliminary evaluations of electrical problem solutions prior to launching full-scale investigations. Such use can result in greater flexibility than afforded by present computer models. Furthermore, numerous problems, which would be virtually impossible to incorporate in a computer model at this time, are more easily analyzed with physical simulation. The development of this system is now proceeding at the USBM's Bruceton Research Facilities. However, electrical specifications of scaled down components for its construction are required. This project is a result of that need and has been funded as an extension to Grant GO-133077. The following report covers these specifications. Scope of Work To represent a mined a-c/d-r. coal mine section, the typical component specifications must detail at least: a. one a-c continuous miner, b. two a-c or d-c shuttle cars, c. one a-c or d-c roof bolter, d. one a-c section fan, and e. feeder cables. Further, each machine should be portrayed by each of its general

Jan 1, 1974

By A. L. Engel

Production of chromite in California has been from many small, high-grade mines. The opening of the Purchase Depot at Grants Pass, Oreg., in 1951 has stimulated chromite mining in California, and a large number of properties are being reexamined as there is a possibility that some low-grade ores from many of these properties can be beneficiated to meet the purchasing schedule. The Bureau of Mines in its program of conservation is continuing ore-dressing tests on chromite ores to better evaluate their potential. This report is a compilation of preliminary concentration tests on samples from five different properties in California. The concentration tests were made on ores from the David mine, Butte County, the Seiad Creek mine, Siskiyou County, the High Plateau mine, Del Norte County, Bud's mine, Tuolumne County, and tailings from the Miller concentration plant in San Luis Obispo County, Calif., to determine the possibility of beneficiating these ores so that they will meet the specifications for the Government stockpile.

Jan 1, 1956

By D. Bienstock, J. H. Field, M. J. Lempel

A computer program is presented to perform the detailed and numerous calculations required for determining the interface temperatures and steady - state heat flow through a furnace wall composed of several refractories in layers . A method is developed that will allow the designer to determine the various thicknesses for each refractory layer to minimize either the total wall thickness or the cost of the wall per unit of area . A sample problem is presented and analyzed to illustrate the techniques involved .

Jan 1, 1964

By Arthur L. Miller

Recent studies suggest that trace metals emitted by internal combustion engines are derived mainly from combustion of lubrication oil. This hypothesis was examined by investigation of the formation of particulate matter emitted from an internal combustion engine in the absence of fuel-derived soot. Emissions from a modified CAT 3304 diesel engine fueled with hydrogen gas were characterized. The role of organic carbon and metals from lubrication oil on particle formation was investigated under selected engine conditions. The engine produced exhaust aerosol with log normal-size distributions and particle concentrations between 105 and 101 cm-3 with geometric mean diameters from 18 to 31 nm. The particles contained organic carbon, little or no elemental carbon, and a much larger percentage of metals than particles from diesel engines. The maximum total carbon emission rate was estimated at 1.08 g h-1, which is much lower than the emission rate of the original diesel engine. There was also evidence that less volatile elements, such as iron, self-nucleated to form nanoparticles, some of which survive the coagulation process.

Jan 1, 2007

By H. E. Peterson, W. L. Anderson

"INTRODUCTION The great demand for tungsten incident to the war has led to the exploration of a large number of low-grade tungsten deposits. To properly evaluate the low-grade deposits it is essential to have available a dependable method of analysis applicable to all types of low-grade tungsten ores. Results reported on the tungsten content of the ores have often varied quite widely and have led to confusion. The Bureau of Mines has been requested by Government lending agencies and by companies interested in the production of tungsten to publish a general method for the determination of tungsten in low-grade ores. To meet this need, the Bureau of Mines is herein submitting two methods for analysis that have been proved on a large number of tungsten-bearing ores various types in the Bureau of Mines laboratory in Salt Lake City. Also, a third method was developed that requires no cinchonine and has proved to be applicable on most tungsten ores. The cinchonine method is the generally accepted for analysis of tungsten ores. Very reliable results can be obtained by this method if certain precautions are taken, as outlined in this report."

May 1, 1943

By E. C. Baker

The capital investment and operating costs of two methane-control systems used during longwall mining operations are compared in this Bureau of Mines report. Costs are given for a surface gob hole drainage system and an underground cross-measure borehole drainage system to control methane gas in gobs in four coal mining areas--central Pennsylvania, northern West Virginia, southern Virginia, and northern Alabama. Present-worth analysis is used to determine the more cost-effective alternative in each location. The alternatives have equal lives and provide the same service based on a minimum rate of return of 15 pet. In central Pennsylvania and northern West Virginia, the gob hole system is more cost effective than the cross-measure system, by 10 and 18 pet, respectively. In southern Virginia and northern Alabama, the cross-measure system is more cost effective, by 29 and 38 pet., respecitively. Costs for other locations must be developed on a case-by-case basis.

Jan 1, 1988

By Charles L. Harnes

A mineral pigment is a colored substance dug from the ground, which after treatment can be mixed with a drying oil to form a paint. Not all colored earths, however, can be made into satisfactory pigment. Much depends upon the attractiveness and uniformity of the color and the ease of purification. Mineral pigments are distinguished from chemical pigments by a difference in origin and treatment. Chemical pigments are not found ready-made in the earth but must be synthesized or otherwise obtained from other compounds or elements; for example, cadmium yellow, a chemical pigment, is precipitated from a solution of cadmium chloride, hydrochloric acid, and sodium sulfide.

Jan 1, 1942

By Florence L. Feicht, H. H. Schrenk, Carlton E. Brown

This report describes the dropping - mercury electrode , its use in analysis , and the procedure of the Health Division of the Bureau of Mines in determining lead , cadmium , and zinc . The dropping - mercury electrode or polarograph is an electrolytic device , one electrode of which consists of mercury issuing in small drops from a capillary tube . Such electrodes have been in existence for more than 50 years, but they were not used for analytical purposes until about 1922.6/ Developments since have been rapid , especially in Czechoslovakia , Germany , Italy, and Japan and more recently in the United States . A recent bibliography / contains references to, 825 articles issued from 1903 through 1940. In 1939 Kolthoff and Lingane presented the first comprehensive critical review, in English , of the device and its use in analysis . They have recently issued a book on the same subject. Similar information also is included in a recent book10/ by Kolthoff and Laitinen . Much of the information in this and the two following sections on this device and its use in analysis was obtained from these three publications . The use of the dropping - mercury electrode in analysis is based upon the fact that the kind and amount of electro - reducible and electro - oxidizable constituents in solution can be determined from the current -voltage relationships revealed by this electrode or electrolytic device .

May 1, 1942

By Robert L. Frantz

This report is a part of the project "Study of the Human Factors Aspects of an Automated Continuous Mining Section". The report covers three phases: Phase I Assessment of the Impact of the Automation Technology on Mining Health and Safety. Phase II Estimation of the Cost-Effectiveness and Productivity of Automation. Phase III Prediction of the Psychological and Organizational Impacts of Automated Mining, The investigation determines that the automation of a continuous mining section will improve the health and safety of the miner, increase productivity and decrease mining costs, result in a more attractive and desirable working environment, and result in a greater rate of return on capital investment.

Jan 1, 1977

By C. H. Fisher, Abner Eisner

"INTRODUCTION Sulphuric acid of various concentrations has long been used as a reagent in the determination of olefins and aromatics in hydrocarbon oils 4 such as gasoline, kerosene, and neutral oils from coal—tar distillates. Despite its long use, however, there is no general agreement as to optimum conditions and concentration of acid, and numerous methods and modifications have been recommended. In most cases, treatment of the neutral oil with 60 to 90 percent sulphuric acid, followed by distillation to the original endpoint to remove olefin polymers, is recommended for the estimation of unsaturated hydrocarbons. The distillate thus obtained is taken as olefin—free oil and used in later stages of the anlysis. Aromatic hydrocarbons generally are determined in the olefin—free oil by suphonation with more concentrated acid (96 to 100 percent and fuming sulphuric acid are recommended), the hydrocarbons not attacked and removed as water—soluble sulphonic acids being considered as saturated hydrocarbons. In some cases the saturates are examined further by differentiatingbetween cyclic (naphthenes) and acyclic hydrocarbons (paraffins). Generally this is achieved by physical methods, although strong sulphuric acid is known to react preferentially with some types of saturated hydrocarbons,It was the purpose of the present work to make a general study of this type of analysis and to investigate the reactions of hydrocarbons under conditions often used in analyses that employ sulphuric acid reagents. Since previous work is not in good agreement, the optimum concentrations of acid for the different stages of the analysis were determined. Several sulphuric acid methods previously recommended and new modifications were compared, two synthetic solutions being used as the reference oil. The results obtained are presented below under separate headings."

Dec 1, 1937

By J. D. Dixon

This Bureau of Mines report describes the results of an investigation for developing and applying procedures for stabilizing excavations openings in highly yielding ground. The approach developed in this report involves nonlinear modeling of the progressive relaxation of the zones of rock mass around the excavations opening where Coulomb criterion of failure is exceeded. Stresses are calculated by using a computer code; Coulomb-failure condition is examined for both intact rock and joints (using strength parameters [~] and c). The rock mass in the failed zones is relaxed by reducing the Young's modulus of the rock based on an empirical formulation that is a function of the shape of the opening and the extent of the failed zone. In addition, the material in the failed zone is assigned reduced strength paramters 0' and c'. The limiting (or convergent) relaxed zone is obtained through an iterative process by manually changing the rock modulus and the strength parameters between iterations. Support pressures are computed by applying forces normal to the excavation surface. The approach is applied to the analysis of stability and support requirements for an entry in a longwall coal mine.

Jan 1, 1985

By C. H. Fisher

Sulphuric acid of various concentrations has long been used as a reagent in the determination of olefins and aromatics in hydrocarbon oils4 such as gasoline, kerosene, and neutral oils from coal-tar distillates. Despite its long use, however, there is no general agreement as to optimum conditions and concentration of acid, and numerous methods and modifications have been recommended. In most cases, treatment of the neutral oil with 80 to 90 percent sulphuric acid, followed by distillation to the original endpoint to remove olefin polymers, is recommended for the estimation of unsaturated hydrocarbons. The distillate thus obtained is taken as olefin-free oil and used in later stages of the anlysis. Aromatic hydrocarbons generally are determined in the olefin-free oil by suphonation with more concentrated acid (96 to 100 percent and fuming sulphuric acid are recommended), the hydrocarbons not attacked and removed as water-soluble sulphoric acids being considered as saturated hydrocarbons. In some cases the saturates are examined further by differentiating between cyclic (naphthenes) and acyclic hydrocarbons (paraffins), Generally this is achieved by physical methods, although strong sulphuric acid is known to react preferentially with some types of saturated hydrocarbons. It was the purpose of the present work to make a general study of this type of analysis and to investigate the reactions of hydrocarbons under conditions often used in analyses that employ sulphuric acid reagents. Since previous work is not in good agreement, the optimum concentrations of acid for the different stages of the analysis were determined. Several sulphuric acid methods previously recommended and new modifications were compared, two synthetic solutions being used as the reference oil. The results obtained are presented below under separate headings.

Jan 1, 1937