Search Documents

By C. M. Flynn

The Bureau of Mines prepared and investigated xanthated sawdust adsorbents to determine their effectiveness in removing heavy metal ions from dilute aqueous solutions, mine-drainage waters, and brines. Stripping of the metal values from the metal-laden adsorbent was also investigated. The treated sawdusts had an adsorption capacity of 0.3 to 0.4 meg/g dry adsorbent for Mn, Co, Ni, Cu, Ag, Zn, Cd, Hg, or Pb from feed solutions with pH 5 to 6. The feed solutions tested included mine-drainage waters and geothermal brine. Effluent metal concentrations as low as 0.05 to 0.1 mg/l were obtained at effluent pH values of 6 to 9. The order of affinity of metals for the sawdust adsorbent is Na«Ca~Mg~Mn<Zn<Ni<Cd<Pb~Cu. The presence of Ca, Mg, or Na in concentrations as high as 2 g/l does not seriously impair the heavy-metal adsorption. Metals were desorbed from the metal-laden adsorbent by elution with dilute mineral acids, sodium cyanide, or salts of ethylenediaminetetra-acetic acid.

Jan 1, 1979

By Martin H. Stanczyk

The direct dissolution of a typical zinc sulfide flotation concentrate by elevated temperature and pressure leaching was investigated. The concentrate assayed about 55 percent Zn, 32 percent S, 6 percent Fe, and 1 percent Pb and contained minor quantities of copper and precious metals. The influence of various factors on the dissolution of the zinc in acidic and ammoniacal pulps when using oxygen as the oxidant was determined. The tests revealed that the sphalerite was difficult to oxidize. Complete dissolution of the mineral required vigorous and intimate nixing of the gaseous, liquid, and sold phases. The addition of pyrite or sulfuric acid to water slurries of the concentrate was required to obtain a high zinc extraction when leaching under acidic conditions. The quantity of pyrite and acid used was about 0.125 and 0.25 pound, respectively, per pound of zinc sulfide contained in the leach charge. In tests with acid, about 96 percent of the zinc was extracted from the concentrate in 1 hour at 200° C. when the oxygen partial pressure was 75 pounds per square inch gage or higher. Leaching with a continuous flow of air as the oxidant gave results that were almost as good as those obtained when oxygen was used, In tests with air fed through the autoclave at 320 liters per hour, 95 percent of the zinc was dissolved in 1 hour, Acid leach solutions assaying approximately 58 grams Zn per liter and containing Fe, Ni, Cr, and Cu impurities were produced in the better tests. The leached residue consisted essentially of red iron oxide together with substantially all of the lead and precious metals.

Jan 1, 1961

By H. H. Schrenk

One phase of the Bureau of Minest work in the field of health and safety is the promotion of safe, satisfactory, and reliable respir atory protective devices. To insure that such devices will be available, the Bureau has established schedules of what it considers the minimum re- quirements for oxygen breathing-apparatus,3 gas masks, hose masks,5/ and mechanical filter-respirators (a schedule of requirements for hose- type supplied-air respirators is being prepared). Approval of oxygen breathing-apparatus is given by the Safety Division; approval of other types of respiratory equipment is given by the Health Division, both divisions being in the Health and Safety Branch, Manufacturers of respiratory protective devices may submit their equipment to the Bureau for approval under the requirements of these schedules. As a prerequisite to submitting a device for approval, the Bureau requires a statement that the device is completely developed and of the design and material that the manufacturer believes suitable for a finished marketable device; that the device has been

Aug 1, 1937

By R. E. Cumings

The Bureau of Mines made electrorefining tests in inert-atmosphere, molten salt cells to develop methods for the preparation of high-purity molybdenum. Seven of the electrolytes investigated were suitable for the preparation of refined metal. The electrolytes were composed of molybdenum chloride in alkali chlorides or mixtures of alkali and alkaline-earth chlorides. An electrolyte composed of potassium chloride and potassium hexachloro-molybdate was selected for a larger scale, more detailed study on the basis of its ease of preparation, its ability to retain the molybdenum salt, and the type of deposits obtained. High-purity molybdenum in the 99.99-percent-purity range was successfully prepared as dense plate up to 80 mils thick and as dendritic crystals. The temperature of electrolysis and the current density were major factors in determining whether plate or dendritic crystals of molybdenum were obtained.

Jan 1, 1966

By Thomas C. Atchison, Joseph M. Pugliese

Six explosives were compared by measuring their strain- producing abilities in limestone . Peak strain , e , varied with scaled distance , R/Ro , according to the following equation : € = Kc (R /R 。)- ". The distance exponent , n , was a constant of the rock and did not depend upon explosive . The strain intercept , Ke , increased with increasing detonation pressure of the explosive . The strain intercept also depended upon the explosive- to - rock impedance ratio . For impedance ratios from 0.53 to 1.38 , the strain intercept was approximately proportional to the medium stress , Pn , as calculated from the explosive detonation pressure , P , and the explosive - torock impedence ratio , Z , by the simple elastic theory relation : P = 2P / ( 1 + Z ) . PD However , the data indicated that , at lower values of impedance ratio , the strain intercept is relatively larger than would be expected from the simple elastic theory . The results presented provide a simple method for predicting the relative effectiveness of different explosives in breaking limestone from the detonation pressures and characteristic impedances of the explosives .

Jan 1, 1964

By E. R. Bauer

This report presents the results of a cooperative study between BethEnergy Mines Inc., Ebensburg, PA, a central Pennsylvania coal mining company, and the U.S. Bureau of Mines to investigate longwall development entry roof instability. In-mine mapping of geologic and deformational features was conducted to reveal the major ground control problems encountered during gate road development. In addition, mining-induced pillar load monitoring was used to indicate development loading on variously dimensioned gate road pillars and to determine if pillar yielding occurred. Finally, visual observations of a variety of roof control methods were used to determine the most effective support elements for controlling cutter roof failure.

Jan 1, 1992

By L. C. IlsLey

In the normal operation of mines, the aggregate effect of many seemingly minor op rations may be very important as respects economy and safety. Anion: these operations is the method employed in coupling and uncoupling mine cars. For economic reasons the equipment in mines has not been protected as well as railroad equipment. It is pertinent that haulage accidents rank second in severity among mine accidents, and that manual coupling of cars has been one of the most frequent causes of such accidents. One study4/ revealed that coupling was responsible for about 20 percent of haulage accidents underground. A review of early conditions on steam railroads, which were responsible for the introduction of safer methods of coupling cars, indicates how conditions in might be improved. THE STORY OF RAILROAD COUPLING As any considerable improvement in mine-car coupling probably will follow lines somewhat similar to those that brought order out of chaos for the railroads, it seems appropriate to review briefly the steps taken to improve railroad coupling from the days of link and pin couplings of various types to the adoption of the standard ?M.C.E? automatic coupler.

Jan 1, 1943

By W. J. Huff, G. W. Jones, I. Spolan, R. E. Kennedy

"INTRODUCTION Information on the exploeibility and ease of ignition of acetylene is important in connection with investigations by the Bureau of Mines and others seeking the causes of explosions in medium-pressure acetylene generators.A previous report 6/ gave preliminary results of an investigation made by this Bureau to determine the causes of these explosions. This report indicated the need of amending Federal specifications for ""1/4 by 1/12"" carbide to reduce the amount of fine sizes permitted under the specifications then in force. Tests described in the above report showed that certain sizes of carbide may, under certain conditions, attain excessively high temperatures when acetylene-water vapor mixtures are passed through carbides for extended periods.Federal specifications P-0-101, Amendment 5, June 28, 1944, are now in effect. These latest specifications permit a maximum of 7 percent of ""1/4 by 1/12"" carbide by weight to pass through a 0.0661-inch sieve and a maximum of 2 percent to pass through a 0.0555-inch sieve. Experience has shown that these specifications have insured a safer size range of carbide for medium-pressure acetylene generators.Although the improvement in the size range of the carbides has aided in the prevention of explosions, there have been explosions in which the carbide used at the time of the explosion met the latest Federal specifications."

Sep 1, 1945

By L. C. IlsLey

The United States Bureau of Mines has been conducting investigations of electrical equipment curing a period of more than 25 years in an endeavor to encourage the development of safer electrical equipment for coal mines. In order to conduct these investigations in an orderly manner they are carried out under a published schedule of tests known as Schedule 20, which specifies detailed requirements for motors, controllers, etc., and fees covering the various inspections and tests made as part of a routine investigation.

Jan 1, 1937

By Robert Bottge

When a company develops a mineral property in a remote area of Alaska, it must consider how best to house its personnel. This Bureau of Mines report examines the economics of two options: company towns and company camps. The price required to maintain a 15% discounted-cash-flow rate of return (DCFROR) was derived for hypothetical 1,000-st/d cut-and-fill mines and 50,000-st/d open-pit mines located in three different regions of the State, One set of hypothetical mines utilizes a townsite; the other utilizes a relatively new concept, a fly-in camp or commuting operation, in which two shifts of employees operate the mine and all associated facilities for 1 week before being replaced by a second crew. The study shows that operating costs were higher for mines employing the commuting option than for mines having a company town because of the additional wages paid for overtime hours; however, the price required to obtain a 15% DCFROR for the single-product copper concentrate, f.0.b. the mill site, was significantly lower owing to the lower investment costs for the camp-type operation. The economic advantage for those mines utilizing the camp increases from south to north and from the coast toward the interior.

Jan 1, 1986

By M. E. Tyrrell, J. Koster

This work was undertaken to determine the feasibility of making mixed diborides of two metals directly from the metal oxides , boron carbide and carbon . The diborides (Ti , V ) , B₂ , (Ti , Cb) B₂ , and ( Ti , Ta ) B₂ were prepared in a crucible resistance furnace at 2,100 ° C , and X- ray- diffraction analyses showed each was a homogeneous solid solution containing approximately equal molar contents of the given diborides . The diboride powders were cold - pressed ; sintered to 2,300 ° C , and evaluated for mechanical strength , rate of oxidation , and resistance to molten metals . The diboride ( Ti , Ta ) B₂ exhibited the best mechanical properties ; the diboride ( Ti , Cb ) B₂ , the lowest cumulative rate of oxidation . The mixtures were stable in the presence of molten aluminum and copper but were attacked by molten Ti , Zr , and Cr .

Jan 1, 1964

By B. W. Gandrud

At the Southern Experiment Station of the Federal Bureau of Mines, reports are prepared from time to time on results of washability studies of commercially important coal beds in the Southern Appalachian region. The investigations that provide the material for these reports are made by the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama and the mine operators. This report records the results obtained on a sample of run-of-mine coal taken in June 1953 from the Pratt bed at the Davidson Coal Co. mine about 1 mile west of Graysville, Ala. One of the main objectives of a washability study is to obtain technically and commercially important data in connection with the best methods for preparing and utilizing the Nation&apos;s limited reserves of good coking coal. Such information is important from the standpoint of conservation in that it facilitates selection of preparation methods that will yield an acceptable grade of coking coal with a mini-mum of losses of coal in the rejects. The Pratt bed is one of the main sources of coking coal in the Jefferson County part of the Warrior field. This is the first time, however, that data from a complete washability study of coal have been obtained from this bed in Jefferson County. In the Graysville area, Pratt-bed coal has good coking characteristics and is used for blending with other coals in making metallurgical coal. The extent of its use in such blends is severely limited in this area, however, by the fact that it has a high sulfur content, which has not been reducible to any great extent by washery treatment.

Jan 1, 1955

By T. E. Green, E. F. Spano, W. J. Campbell

A combined ion - exchange X- ray spectrographic method was developed and evaluated for determining trace amounts of cobalt and nickel in high - purity tungsten and tungsten trioxide . The sensitivity for both cobalt and nickel is in the range from 0.2 to 0.5 μg ( 0.04 to 0.1 ppm , based on 5 gram samples ) . Accuracy at the 5 to 20 μg level is ±10 percent of the amount present . Approximately 16 hours elapsed time is required for analysis

Jan 1, 1963

By Oliver Bowles

"The American Consul at Guatemala City reports that the Guatemala Marble Mining Company is preparing to operate a marble quarry about 13 miles from the railroad station of Zacapa, which station is a little over 100 miles from Puerto Barrios, the nearest port from which the product may be shipped. The deposit is extensive, and though somewhat broken up in places, great quantities of sound marble are available. It is claimed that the marble is equal in quality to the best product of the Italian Carrara quarries.Access to the quarry by rail is obtained by a spur track of the International Railways of Central America (Ferrocarril Internacional de Centro America) from Marmol, 3 miles south of Zacapa. This spur is about 5 miles long and terminates at the foot of the mountains. A double-track incline cable-way 2000 feet in length has been constructed to bring the marble down the mountain. From the top of the incline to the quarry there is a railway six miles in length over which the rock will be hauled by two side-geared Shay locomotives."

Mar 1, 1920

By Joseph M. Singer

Having established that sodium chloride reduces the incendivity of explosives, the Bureau of Mines studied the effect of sodium nitrate in reducing ignition hazards. Gallery experiments showed that sodium nitrate reduced the incendivity of certain explosives to 8 percent natural gas in air but increased their incendivity to coal dust predispersed in air. Laboratory experiments using hot jets from explosions of stoichiometric mixtures of methane-oxygen-nitrogen showed that both sodium chloride and sodium nitrate reduced the incendivity to methane, to mixtures of coal dust and methane) and to coal dust. The difference between the gallery and laboratory results with respect to coal dust is attributed to temperature-time effects.

Jan 1, 1967

By O. C. Blade

This report is one of a series made by the Bureau of Mines under a cooperative agreement with the American Petroleum Institute on the characteristics of commercial aviation gasolines. The series of Surveys is a continuation of like work conducted under aimil.ar cooperative agreements with the Coordinating Research Council, Inc. by the National. Bureau of Standards from 1940 through 1946 and by the Bureau of Mines from 1947 through 1949. A completed list of the series of surveys is given at the end of this paper.

Jan 1, 1951

By G. L. Neumann

Owing to the need for additional sources of supply of both zinc and lead following World War II, the Bureau of Mines investigated many abandoned lead-zinc mines in the eastern United States. A series of shallow veins in south-western St. Lawrence County has long been a subject of speculation. These veins, which average about 4 feet in width and cut across the bedding of the country rock at right angles, are filled with calcite-carrying galena and sphalerite. The deposits have been worked sporadically during the last 115 years. From 1837 to 1852 the Coal Hill, the North, and the Victoria mines near the village of Rossie were at their peak of activity. Other calcite veins were prospected and a small production was realized. The Bureau of Mines began diamond drilling May 1, 1950, under the general supervision of McHenry Mosier, chief, Mining Branch, Bureau of Mines, Region VIII, and under the immediate supervision of the author) who was project engineer, following the preliminary examination by Robert S. Sanford. A total of 3,870.2 feet was drilled in 18 holes on four of the numerous deposits scattered over Macomb and Rossie townships. Drilling was completed September 21, 1950.

Jan 1, 1952

By F. E. Block, Stephen D. Hill

The necessity for measuring radiation dose is encountered in studying both the beneficial and damaging effects of ionizing radiation on materials . It is also necessary to know the radiation dose absorbed by the reactants in order to evaluate the efficiency of reactions or processes that are promoted by radiation . Thus , a significant effort was made at the Albany cobalt 60 facility to investigate techniques by which the exposure radiation dose can be determined . Methods including ferrous sulfate , ceric sulfate , and methyl methacrylate chemical dosimeters , ion chamber dosimetry , and an absolute radiation calorimeter were investigated . Isodose curves were constructed for several standard source configurations using the dosimetry techniques which were investigated .

Jan 1, 1964

By Alan R. Buehler

In 1986, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied part of the 256,430-acre Alvord Desert and part of the 22,240-acre East Alvord Wilderness Study Area (OR-002-074 and OR-002-073A, respectively), in order to evaluate their identified mineral resources. The study areas are located in Harney and Malheur Counties, OR, about 25 mi northeast of the small village of Fields. There are no mines, prospects, or identified mineral resources inside the study areas. Basalt flows within the study areas contain chalcedony-lined vugs and banded agate which may be of interest to rock hounds. An ignimbrite flow contains perlitic material, but crystalline contaminants make it unsuitable for commercial uses. Lacustrine (lake) sediments contain diatomite and clays, and evaporite crusts contain boron too low grade to profitably mine. Small quantities of common opal and petrified wood occur which might be of possible interest to rock hounds. Some of the petrified wood is black, free of fractures, and polishes well; it may be suitable as backing material for soft, thin, and brittle gemstones, such as precious opal. The lacustrine sediments also contain black, fetid layers which have above background, but economically insignificant concentrations of zinc, cobalt, nickel, barium, iron, manganese, aluminum, and potassium. Large quantities of fine-grained dune sands within the study areas are too far from markets for economic consideration. Ephemeral streams in the study areas contain small amounts of placer gold of no economic interest. The western portions of both study areas are reported to have moderate favorability for occurrences of natural gas, and both study areas are reported to have high favorability for the occurrence of geothermal resources. As of December 1986, oil and gas leases covered 3,100 acres in the study areas.

Jan 1, 1987

By Manuel Gomez

A lignite from Milam County, Tex., has been oxidized by air at temperatures from about 27° to 300° C. for varying lengths of time. The oxidized coal was carbonized at 500° C. in a laboratory assay unit, and the products of carbonization were measured and analyzed. The data presented suggest that, as lignite is progressively oxidized, tar yields are decreased and gas yields are increased in a ratio approximating 1:1. It is surmised that tar-yielding structures in the nonoxidized coal produce gas, principally, when the coal is oxidized. Char-yielding structures of the nonoxidized coal give rise to additional water of decomposition after oxidation and pyrolysis. As lignite is subjected to greater oxidation, the gaseous product evolved on pyrolysis becomes almost entirely carbon dioxide. Tar yields decrease with an increased degree of oxidation, so that the reduction in tar yield may be used as a qualitative measure of oxidation. Pilot-plant drying and carbonization, where air is used as the transport gas and where some air is included in the drying and carbonizing gases, induces some oxidation of the coal particle. The short residence time in a fluidized system with reference to the oxidation environment limits the oxidation.

Jan 1, 1956